Project Status and Action Items
Worked for 1 min 27 sec
Done. I deleted
CN1 and moved U_MCU/Pico to the top of the board; it is now centered at about (10 mm, 88 mm) with its top edge just inside the board outline.Open item: the Pico was clamped at the board edge, so if you want more clearance from the top edge I can drop it slightly lower.
I need a power switch and some output LEDs
Thought for 5 sec
I’ll add a low-current front-panel power/enable switch rather than a high-current 12 V path switch, plus output/status LEDs with current-limiting resistors, then verify the schematic changes.
Worked for 1 min 54 sec
Added the power switch and output LEDs.
SW_PWR is a low-current front-panel switch that pulls Pico 3V3_EN to GND to turn logic off, and I added green indicators for BUS_12V and VOUT_19V5 with 4.7kΩ and 8.2kΩ series resistors.Open items:
- These are placed near the top/front-panel area but not routed yet.
- If you intended a true high-current input disconnect instead of a Pico enable switch, that needs a different switch/contactor architecture.
Route controls and verify
Use high-current switch
Route switch and LEDs
Add LED labels
Run design review
Refine this doc
Ask about this doc
Imported Connector Verification
ED32BGFBK
- Source file:
ED32BGFBK.elibz - Imported project: /kproc/ed32bgfbk
- Part UID:
63e570f9-6b31-4efa-8903-7a82ab48a548 - Manufacturer: WingTAT
- MPN: ED32BGFBK
- Designator prefix: J
Verification Result
- Published as part: yes.
- Schematic components: 0.
- Nets: 0.
- PCB layout nodes: 1.
- Conclusion: import is footprint-only. It currently has no schematic terminals, so it cannot be wired into the distribution-board schematic.
Repair Attempt Result
A repair thread was started in the part project, but it reported that available tools could not add schematic terminals/symbols to the footprint-only imported part. The part still has 0 schematic terminals.
Required Repair
Use the Flux part editor or an importable EDA library that includes both symbol and footprint. Add a schematic symbol with 32 terminals and map those terminals to the footprint pads. Use the pin allocation in
edge-connector-pinout-rev-a-daughterboard-slot unless the imported footprint numbering proves a different physical order.DC-S007B-D025-15A
- Source file:
DC-S007B-D025-15A.elibz - Imported project: /kproc/dc-s007b-d025-15a
- Part UID:
76dfedca-adc2-4fc1-b509-603f002c2698 - Manufacturer: G-Switch
- MPN: DC-S007B-D025-15A
- Designator prefix: J
Verification Result
- Published as part: yes.
- Schematic components: 0.
- Nets: 0.
- PCB layout nodes: 1.
- Conclusion: import is footprint-only. It currently has no schematic terminals, so it cannot be wired into the daughterboard output schematic.
Repair Attempt Result
A repair thread was started but did not complete in a reasonable time and the part still shows 0 schematic terminals. The thread was stopped to avoid indefinite execution.
Required Repair
Use the Flux part editor or an importable EDA library that includes both symbol and footprint. Add a schematic symbol with the connector's real electrical terminals from the datasheet/footprint. Minimum expected terminals are likely center positive, sleeve/ground, and any switched/contact-detect pins if present. Do not assume pinout until the footprint/datasheet is verified.
Current Schematic Impact
Neither imported connector has been added to the active schematic because footprint-only parts would create unusable/no-terminal schematic instances. Once repaired, add:
- 12× ED32BGFBK to the distribution board slot interface.
- 1× DC-S007B-D025-15A per daughterboard output.
ED32BGFBK
Verification Result
Repair Attempt Result
Required Repair
DC-S007B-D025-15A
Verification Result
Repair Attempt Result
Required Repair
Current Schematic Impact
