LED Driver IC 1 Output DC DC Controller SEPIC, Step-Down (Buck), Step-Up (Boost) Analog, PWM Dimming 8-SO-EP # AL8866QSP-13 Engineering Specifications **General Description** The AL8866QSP-13 is an automotive-qualified, multi-topology DC-switching LED controller manufactured by Diodes Incorporated. It is designed to control an external power MOSFET for high-power automotive LED lighting systems. The device supports buck, boost, buck-boost and single-ended primary-inductance converter configurations. Its wide input-voltage range makes it suitable for automotive power systems and various high-voltage LED applications. The controller uses fixed-frequency peak current-mode regulation with spread-spectrum frequency modulation to reduce electromagnetic interference. It supports both analog and pulse-width-modulation dimming through the DIM input. An integrated programmable soft-start function gradually increases the inductor and switching currents during startup to reduce output-voltage and current stress. The open-drain fault output provides system-level fault reporting for abnormal operating conditions. **Engineering Specifications** **Manufacturer:** Diodes Incorporated **Manufacturer Part Number:** AL8866QSP-13 **Component Type:** Automotive LED driver controller **Converter Topologies:** Buck, boost, buck-boost and SEPIC **Control Architecture:** Fixed-frequency peak current-mode control **External Switching Device:** External power MOSFET **Minimum Input Voltage:** Four point seven volts **Maximum Input Voltage:** Eighty-five volts **Maximum Output Voltage:** Eighty-five volts **Switching Frequency:** Four hundred kilohertz **Frequency Modulation:** Spread-spectrum modulation for reduced electromagnetic interference **LED Current Control:** External current-sense resistor and external MOSFET configuration **Feedback Voltage:** Two hundred millivolts **Typical Quiescent Current:** One point eight milliamperes **Typical Efficiency:** Up to approximately ninety-three percent, depending on the application circuit and external components **Dimming Methods:** Analog dimming and pulse-width-modulation dimming **Analog Dimming Range:** One percent to one hundred percent **Analog Dimming Dynamic Range:** Greater than one hundred to one **Pulse-Width-Modulation Dimming Ratio:** One hundred to one at a two-hundred-hertz dimming frequency **Pulse-Width-Modulation Frequency Range:** Approximately one hundred hertz to one kilohertz **Full-Brightness Current Accuracy:** Approximately plus or minus three percent **Low-Level Dimming Current Accuracy:** Approximately plus or minus twelve percent at twenty-percent dimming **Soft-Start Function:** Externally programmable **Fault Output:** Active-low open-drain fault indicator **Protection Features:** Output overvoltage protection, LED open-circuit protection, output undervoltage protection, LED short-circuit protection, cycle-by-cycle overcurrent limitation, current-sense resistor short-circuit protection, inductor and diode short-circuit detection, diode open-circuit protection and thermal shutdown **Automotive Qualification:** AEC-Q100 Grade One qualified **Automotive Documentation:** PPAP capable **Manufacturing Standard:** Manufactured in IATF-certified automotive facilities **Operating Temperature Range:** Minus forty degrees Celsius to positive one hundred twenty-five degrees Celsius **Package Type:** Thermally enhanced SO-8 exposed-pad package **Pin Count:** Eight leads with exposed thermal ground pad **Mounting Style:** Surface mount **Packing Method:** Thirteen-inch tape and reel **Standard Packing Quantity:** Two thousand five hundred components per reel **Moisture Sensitivity:** Level One **Terminal Finish:** Matte-tin-plated leads **Environmental Compliance:** Lead-free, RoHS compliant, halogen-free and antimony-free **Typical Applications** Automotive high-beam and low-beam lighting Automotive daytime running lights Automotive fog lights Automotive turn-signal lights Automotive position lights Automotive brake and stop lights High-power exterior LED lighting Multi-topology automotive LED driver modules #AL8866QSP13 #AL8866Q #DiodesIncorporated #LEDDriver #AutomotiveLED #AutomotiveElectronics #BuckConverter #BoostConverter #BuckBoostConverter #SEPICConverter #PowerElectronics #LEDLighting #ElectronicComponents #EngineeringSpecifications

Non-Synchronous Buck DC-DC Converter – 3 A non-synchronous step-down (buck) switching regulator with an integrated 80 V, 3.5 A power MOSFET for industrial, telecom, and high-voltage power supply applications. Operates from a 12 V to 76 V input voltage, provides an adjustable output voltage from 1.0 V to 76 V, and features a programmable switching frequency from 50 kHz to 750 kHz. Includes current-mode control, soft-start, enable input, 0 µA standby current, precision reference (±1.5%), externally programmable undervoltage lockout (UVLO) with hysteresis, overcurrent protection (OCP), overvoltage protection (OVP), and thermal shutdown (TSD). Specified for operation over a −40°C to +85°C temperature range and housed in an 8-pin HTSOP-J exposed-pad package. #ROHM #BD9G341AEFJE2 #BD9G341AEFJ #BuckConverter #DCDCConverter #StepDownRegulator #SwitchingRegulator #PowerManagement #3A #80VMOSFET #IndustrialPower #HTSOPJ8 #EmbeddedSystems

Buck Switching Regulator IC Positive Adjustable (Fixed) 0.8V (3.3V, 5V) 1 Output 4.5A 20-WFQFN Exposed Pad The LM656x5-Q1 are a family of automotive buck converters designed for high efficiency, high-power density, and ultra-low electromagnetic interference (EMI). The converters operate over a wide input voltage range of 3V to 65V (70V transient < 100ms), reducing the need for external input surge protection. The LM656x5-Q1 comes with pin selectable fixed output voltages of 3.3V and 5V or in adjustable configuration. The low EMI operation is enabled with minimized loop inductance and optimized switch node slew rate. A pin-selectable ±5% or ±10% dual-random spread spectrum (DRSS) significantly reduces peak emissions through a combination of triangular and pseudo-random modulation while keeping output voltage ripple very low. The current-mode control architecture with a 30ns typical minimum on-time allows high conversion ratios at high frequencies coupled with a fast transient response and excellent load and line regulation. Features • AEC-Q100 qualified for automotive applications: – Temperature grade 1: –40°C to +125°C, TA • Wide input voltage range: 3V to 65V (70V transient < 100ms) – Meets LV148 / ISO21780 requirements • Designed for low EMI requirements – Facilitates CISPR 25 class 5 compliance – Mode pin configurable ±5% or ±10% dualrandom spread spectrum reducing peak emissions – Enhanced HotRod™ QFN package with symmetrical pinout – Switching frequency from 300kHz to 2.2MHz – Pin-configurable AUTO or FPWM operation – Internal compensation, current limit, and TSD • Low minimum on time: 40ns (maximum) – Enables 36VIN to 3.3VOUT conversion at 2.2MHz • High-efficiency power conversion at all loads – > 94% peak efficiency at 24VIN, 5VOUT, 400kHz – 2.5µA switching input current at no load • High power density – 3.6mm × 2.6mm, wettable flank, 20-pin package – Pin compatible with 36V LM654x0-Q1 – ϴJA = 24.0°C/W (LM65645-Q1EVM) • Create a custom design using the LM656x5-Q1 with the WEBENCH® Power Designer 2 Applications • Advanced driver assistance systems (ADAS) • Automotive infotainment and cluster • Hybrid, electric, and powertrain systems #AutomotiveElectronics #BuckConverter #DCDCConverter #PowerManagement #VoltageRegulator #SynchronousBuck #LowEMI #AECQ100 #TexasInstruments #EmbeddedSystems

DC/DC Switching Regulator, configurable as a boost, buck-boost, SEPIC, flyback, or inverting converter with a 5 V to 32 V input voltage range, up to 60 V output switch voltage, 4 A maximum switching current, and 400 kHz fixed switching frequency. Features current-mode control, an adjustable 1.25 V feedback reference, integrated power MOSFET, soft-start, current limiting, thermal shutdown, and TTL-compatible enable input. #DCDCConverter #SwitchingRegulator #BoostConverter #BuckBoostConverter #SEPICConverter #FlybackConverter #InvertingConverter #CurrentMode #400kHz #4A #60V #TO2635L #XLSEMI #XL6009E1

MPS MP1584 high-frequency step-down buck converter, 3A output current, 4.5V to 28V input voltage range, integrated high-side power MOSFET, current-mode control, programmable switching frequency from 100kHz to 1.5MHz, high-efficiency pulse-skipping mode for light loads, ceramic capacitor stable, internal soft-start, internal current limit, fault protection and thermal shutdown, available in SOIC-8E package, suitable for automotive, industrial, distributed power and battery-powered systems. MP1584, MPS MP1584, Monolithic Power MP1584, MP1584 buck converter, MP1584 step down converter, 3A buck converter, 28V buck converter, 1.5MHz buck converter, SOIC-8E buck converter, adjustable DC DC converter, high efficiency buck regulator, MP1584EN, MP1584 datasheet #MP1584 #MPSMP1584 #MonolithicPower #BuckConverter #StepDownConverter #DCDCConverter #3ABuckConverter #28VConverter #15MHzConverter #SOIC8E #PowerManagementIC #SwitchingRegulator

The NCP1345, manufactured by onsemi, is a highly integrated quasi-resonant flyback controller optimized for high-performance off-line USB-PD and USB Type-C power converters. This advanced controller features a dual-pin Vcc architecture for simplified Vcc management and enhanced performance, allowing direct connection to the auxiliary winding. It incorporates a precise primary side-based output current limiting circuit to ensure a constant output current limit irrespective of the programmed output voltage or nameplate output power. The quasi-resonant (QR) current-mode flyback stage is equipped with proprietary valley-lockout circuitry for stable valley switching down to the 6th valley and transitions to frequency foldback mode to reduce switching losses. Additional load decreases trigger the NCP1345 to enter skip mode for efficient power management. Key protective features include internal brownout detection, maximum output current limit, latched overvoltage, and NTC-ready overtemperature protection, as well as line removal detection for safe discharge of X2 capacitors. The NCP1345 is available in SOIC-9 NB packages and supports various configurations and protection mechanisms, making it a robust solution for modern power supply designs.

The TPS54531DDA is a high-efficiency step-down switching regulator designed for converting higher input voltages into regulated lower output voltages. It integrates a power MOSFET, control circuitry, and protection features into a compact package, enabling simplified power supply design for a wide range of industrial, consumer, communication, and embedded applications. The device utilizes current-mode control architecture to provide fast transient response, stable operation, and straightforward loop compensation. It supports a wide input voltage range and delivers efficient power conversion while minimizing external component count. Built-in protection mechanisms enhance system reliability by safeguarding against fault conditions such as overcurrent, undervoltage, and thermal overload. The TPS54531DDA is commonly used in distributed power systems, industrial controllers, networking equipment, telecommunications hardware, battery-powered devices, and embedded computing platforms requiring efficient voltage regulation. Features Integrated high-side power MOSFET High-efficiency buck regulator architecture Wide input voltage operating range Current-mode control operation Adjustable output voltage capability Fast transient response performance Internal soft-start functionality Cycle-by-cycle current limiting protection Thermal shutdown protection Undervoltage lockout protection Frequency compensation support Low standby current operation Compact surface-mount package Suitable for industrial temperature environments Electrical Characteristics Step-down DC/DC conversion topology Fixed switching frequency operation Adjustable output regulation High conversion efficiency across load conditions Stable operation with ceramic output capacitors Integrated power switch architecture Low output voltage ripple performance High load regulation accuracy Applications Industrial automation systems Embedded processors and microcontrollers Communication equipment Networking hardware Distributed power architectures Point-of-load regulators Consumer electronic products Measurement and instrumentation equipment Battery-powered systems Digital control platforms Package Information Package Type: SO PowerPAD package Surface-mount assembly compatible Thermally enhanced package construction Optimized for automated PCB manufacturing Compact footprint for space-constrained designs #commonpartslibrary #integratedcircuit #powermanagement #powersupply #buckconverter #dcdcconverter #switchingregulator #voltageregulator #embeddedsystems #industrialelectronics #powerelectronics #texasinstruments #energyefficiency #electronicsdesign #powersupplycontroller

DC-DC Controllers LM5176PWPR HTSSOP-28_L9.7-W4.4-P0.65-LS6.4-BL-EP LCSC Part Number: C442493 JLCPCB Part Class: Extended Part Manufactured by TI(德州仪器) Texas Instruments LM5176 synchronous 4-switch buck-boost DC/DC controller, regulates output voltage above, below or equal to input voltage, wide 4.2V to 55V input voltage range with 60V absolute maximum, adjustable 0.8V to 55V output voltage, single-inductor buck-boost architecture, current-mode control, high-efficiency buck-boost transition, adjustable switching frequency with optional synchronization and dithering, integrated 2A MOSFET gate drivers, cycle-by-cycle current limit, optional hiccup protection, input UVLO, soft-start, power-good output, output overvoltage protection, available in HTSSOP-28 and QFN-28 packages. Search Keywords: LM5176, Texas Instruments LM5176, TI LM5176, LM5176 buck boost controller, LM5176 4 switch buck boost, LM5176 synchronous buck boost controller, 55V buck boost controller, 4.2V to 55V DC DC controller, adjustable buck boost controller, single inductor buck boost controller, LM5176 HTSSOP-28, LM5176 QFN-28, LM5176 power supply controller, LM5176 USB power delivery, LM5176 battery powered systems, LM5176 LED lighting, LM5176 datasheet Hashtags: #LM5176 #TexasInstrumentsLM5176 #TIBuckBoostController #BuckBoostController #SynchronousBuckBoost #4SwitchBuckBoost #DCDCController #55VController #SingleInductorBuckBoost #CurrentModeController #MOSFETGateDriver #2AGateDriver #AdjustableFrequencyController #UVLOController #PowerGoodController #OutputOVP #HTSSOP28 #QFN28

Buck Switching Regulator IC Positive Adjustable 0.8V 1 Output 3A 8-SOIC (0.154", 3.90mm Width) Exposed Pad MP1584EN-SOP8 MP1584EN-LF-Z is a high-frequency, non-synchronous step-down (buck) DC-DC switching regulator from Monolithic Power Systems. It integrates a high-side power MOSFET and is designed to efficiently convert input voltages from 4.5V to 28V into a lower, regulated output voltage with up to 3A output current. Its high switching frequency enables the use of small external components, making it ideal for compact and cost-effective power supply designs. Key Features: • Wide 4.5V to 28V input voltage range • Adjustable output voltage from 0.8V to 25V • Up to 3A continuous output current • Integrated high-side power MOSFET • Programmable switching frequency from 100kHz to 1.5MHz • Current-mode control for fast transient response • High efficiency with pulse-skipping mode at light loads • Low quiescent current operation • Internal soft-start function • Over-current and thermal shutdown protection • Stable with ceramic output capacitors • Available in SOIC-8E package with exposed thermal pad #MP1584EN #BuckConverter #DCDCConverter #SwitchingRegulator #PowerManagement #VoltageRegulator #MPS #MonolithicPowerSystems #EmbeddedSystems #ElectronicsDesign #PowerSupply #PCBDesign #HardwareEngineering #Electronics #Semiconductor #power #PMIC #IC

DC-DC Controllers LM5146QRGYRQ1 VQFN-20_L4.5-W3.5-P0.50-BL-EP-1 LCSC Part Number: C1850329 JLCPCB Part Class: Extended Part Manufactured by TI(德州仪器) Texas Instruments LM5146-Q1 100V synchronous buck DC/DC controller for automotive applications, AEC-Q100 Grade 1 qualified, 5.5V to 100V wide input voltage range, adjustable output voltage from 0.8V to 60V, 150°C maximum junction temperature, 100% duty cycle operation during input voltage dips, 40ns minimum high-side on-time, 140ns minimum off-time, switching frequency from 100kHz to 1MHz with synchronization capability, 7.5V gate drivers for standard VTH MOSFETs, 2.3A source and 3.5A sink gate drive capability, lossless RDS(on) or shunt current sensing, adjustable soft-start, hiccup overcurrent protection, UVLO, PGOOD indicator, thermal shutdown, 20-pin VQFN package. Search Keywords: LM5146-Q1, Texas Instruments LM5146-Q1, TI LM5146-Q1, LM5146 automotive buck controller, 100V synchronous buck controller, AEC-Q100 buck controller, LM5146-Q1 VQFN-20, wide input buck controller, 5.5V to 100V buck controller, 0.8V to 60V output controller, 48V automotive buck controller, HEV EV buck controller, ADAS buck controller, LM5146-Q1 datasheet Hashtags: #LM5146Q1 #TexasInstrumentsLM5146Q1 #TIBuckController #SynchronousBuckController #100VBuckController #AutomotiveBuckController #AECQ100 #WideInputController #48VAutomotive #HEVPowerSupply #EVPowerSupply #ADASPower #MOSFETGateDriver #CurrentModeController #VQFN20