WiFi-enabled 3/4-inch PVC ultrasonic water flow meter with protected USB-C power, ESP32 WiFi, 3.3V regulation, 12V sensor supply branch, RS485 sensor interface, UART programming, reset network, and status LEDs.

Per-channel low-voltage controller PCB for RIL TC/HF/LeTID and PID test benches. STM32H7, 16-bit DAC setpoints, 24-bit ADC sense (4-wire), isolated digital interface to gate driver, PT100/RH conditioning, Ethernet, interlocks. Safety-critical brain board.

Jerky Robot V3 100 mm × 152 mm 2-layer control board with ESP32-S3 and Arduino Nano sockets, screw-terminal I/O, BSS138 UART level shifting, PC817 sensor isolation, optional HX711 interface, status LEDs, test points, top-side component placement, and bottom GND fill for JLCPCB fabrication.

NFC-harvested Omni-Touch wearable board with PN7160 frontend, STM32L041 host MCU, SE050 secure element, palm-grid matrix interface, fingerprint UART connector, and status LED on a flex smart-card form factor.

Slot-machine telemetry board with 5V or 12V input, removable ESP32 module interface, Ethernet connectivity, and isolated money pulse inputs.

Isolated PLC-to-LVDS interface board with one trigger output, two LVDS status return channels, DB9 field connector, selectable 5 V or 24 V trigger conditioning, and protected 24 V power input.

ESP32-based sensor camera system with HC-SR04, NEO-6M GPS, ESP32-CAM, optional FT232RL programming interface, 5V input, and regulated 3.3V logic rail.

ESP32-S3 quadcopter flight controller with OV5640 24-pin DVP camera interface, Wi-Fi video link, BLE telemetry, onboard USB-C power/programming, IMU, barometer, ToF altitude sensing, lidar connector, and 4 ESC PWM outputs.

EV motorcycle instrument cluster using STM32H743IIT6 main MCU, display interface, CAN, USB, charging, and power supervision

Compact 2-layer ESP32-S3-MINI-1 piezo TX/RX board for a shared 3 MHz transducer node. Includes USB 5 V input, TP4056 single-cell LiPo charging, TLV75533 3.3 V regulation, ferrite-bead isolated 3V3_ANALOG rail, ~12 V pulsed TX boost rail, low-gate-charge NMOS transmit driver, clamp-protected RX input, 2-stage OPA836 analog receive chain, envelope detector, ADC interface, TMP117 I2C temperature sensor, and status LEDs. Layout intent: piezo centered, RX chain within 10 mm of PIEZO_NODE, boost section remote from RX, digital and analog partitioning, and AGND/DGND star connection near RX front end.

ESP32-S3 touch display development board standardized on a portrait ILI9341 TFT by default, preserving USB-C power, CP2102N USB-UART, I2C touch, PCM5102A audio, microSD, and expansion while assigning KEY1-KEY5 to BOOT, RESET, USER1, USER2, and USER3. The next design pass is driven by a portrait-oriented board resize and user-facing edge placement of the display area, touch interface, controls, and primary connector access.

Multi-layer circular BLDC motor controller for a 24 V, up to 750 W system using an ESP32-WROOM with DRV8323RS gate driver, six external MOSFETs, 2 mOhm shunt current sensing, bottom-mounted AS5600 encoder, USB-C programming/user interface, 3.3 V logic powered from the DRV8323RS buck regulator, and heavy motor phase pads sized for approximately 30 A current paths. Target layout is a circular board around 50 mm diameter, expandable if required for thermal management, power routing, and signal integrity.

This project is a BLE door and window sensor design that uses a U-blox BMD-330-A-R for BLE communication, a reed switch as a sensor, a multi-color LED for status display, and is powered by VBAT. There's also a programming interface and reset switch included. #WiFi #BLE #MCU #ReferenceDesign #project #referenceDesign #simple-embedded #ublox #template #reference-design

This project is a BLE door and window sensor design that uses a U-blox BMD-330-A-R for BLE communication, a reed switch as a sensor, a multi-color LED for status display, and is powered by VBAT. There's also a programming interface and reset switch included. #WiFi #BLE #MCU #ReferenceDesign #project #referenceDesign #simple-embedded #ublox #template #reference-design

Carte STM32F103 2 couches avec alimentation 3,3 V régulée, quartz 16 MHz, USB 2.0 Full-Speed, interface SWD et support de fabrication.

Experimental 21V/5S Li-ion DeWalt battery charger with 21V DC input, relay-switched charge path, tap monitoring, ESP32-WROOM external controller interface, test header, and 2-layer prototype PCB intent.

Raspberry Pi 5 HAT for the Tense Sapphire P.K.E. Meter with two GPIO-driven LEDs, one buzzer, and two GPIO buttons on the 40-pin HAT interface.

Handheld Xbox 360 system with integrated controller electronics, battery-managed USB-C PD power, and a separate dock that automatically switches display, Kinect, and DVD drive paths through a mezzanine docking interface.

Glove interface board using Seeed Studio XIAO ESP32S3. Manufacturing path updated for partial assembly: preserve existing glove interface circuitry (FSR inputs on J3-J7, I2C on J8, SPI on J9, pull resistors R1-R7, decoupling C1) and source U1 separately because JLCPCB stock for MPN 113991114 is unavailable. Assemble all other parts normally, leave U1 for customer-supplied/manual installation, and do not substitute U1 unless a verified XIAO-format pin-compatible replacement is explicitly approved.

FlowState Headband EVT1 — 4-Channel EEG Calibration Device Closed-loop EEG neurofeedback headband for theta/beta baseline calibration. 4-layer mixed-signal PCB, 40x30mm. Core ICs: - ADS1299-4PAG (TI) — 4-channel 24-bit EEG analog front end, SPI interface, 250 SPS - nRF5340 (Nordic) — Dual-core BLE 5.3 SoC, 128 MHz app core + 64 MHz network core Key requirements: - Separate analog and digital power domains (dual LDO: LP5907 for AVDD, AP2112 for DVDD) - Split analog/digital ground planes with single-point connection - 6 electrode inputs (4 active + 1 reference + 1 DRL) with individual TVS ESD protection on each - LIS2DH12 accelerometer (I2C) for motion artifact detection - MCP73831 USB-C battery charging (300-500 mAh LiPo) - 2.4 GHz chip antenna or PCB trace antenna at board edge with 10mm keepout - Conformal coating for sweat/moisture protection Reference designs: - Analog front-end: TI ADS1299 EVM (SBAS499) - Digital/BLE: Nordic nRF5340 DK reference schematic Critical constraint: Microvolt-level EEG signals — analog input routing and power supply filtering are the highest-priority layout concerns.

Wearable closed-loop ultrasonic monitoring and transcutaneous neuromodulation system based on ESP32-C3, powered from a 7.4 V 1000 mAh LiPo battery with TP4056 charging, MT3608 boost conversion, AMS1117-3.3 regulation, JSN-SR04T ultrasonic sensing, LED and buzzer alerts through a BC547 driver, and a reserved neuromodulation interface for future integration.

Datasheet-driven MFRC522 RFID reader PCB intended to replicate RC522 module behavior at 13.56 MHz with a 3.3 V nominal supply, 2.5 V to 3.3 V operating range, and RC522-style 8-pin host header compatibility. The MFRC522 datasheet is the authoritative source for pin usage, power rail relationships, oscillator requirements, reset/IRQ handling, and antenna interface topology. AVDD, DVDD, and TVDD must be tied to the same 3.3 V rail; PVDD must be equal to or lower than DVDD; unused MFIN must be tied to SVDD or PVSS; SVDD must be tied to a valid supply if not used independently. The design must use a 27.12 MHz crystal meeting CL 10 pF and ESR <= 100 ohms, local 100 nF decoupling on each MFRC522 supply grouping plus bulk capacitance, and an RF front-end based on the MFRC522 application diagram and reference reader matching/tuning network. PCB priorities are short crystal and RF connections, compact placement of decoupling capacitors at supply pins, solid ground reference, and protected antenna region with minimal digital routing through the RF area.

Driver drowsiness detection ECG front end based on the AD8232 with ECG electrode interface, analog signal conditioning, a dedicated 50 Hz twin-T notch filter for power-line interference rejection, regulated low-noise analog power, and a downstream conditioned ECG output prepared for processing and fatigue/drowsiness analysis.

MagicGlow smart key tray annular PCB with dual WS2812B rings, ESP32-C6 control, HX711 load-cell interface, USB-C power/UART access, buzzer, and button.

Self-Powered RF Transceiver Module for EM Sensing with RF Prescaler, Divider Chain, and ESP32-S3 Interface