N-Channel 30 V 5.7A (Ta) 1.4W (Ta) Surface Mount SOT-23-3 The AO3400A N-Channel MOSFET is a 30V N-channel enhancement-mode MOSFET designed using trench MOSFET technology. It is widely used for load switching, DC-DC converters, motor driving, and PWM control applications due to its very low on-resistance and compact SOT-23 package. It is especially popular in small electronics and embedded systems because it can be driven directly by 3.3V or 5V logic signals, making it ideal for microcontroller-based designs. Key Features Drain-Source Voltage (VDS): 30V Continuous Drain Current (ID): up to 5.7A (at 25°C) Ultra-low RDS(on): ~26.5 mΩ @ VGS = 10V ~32 mΩ @ VGS = 4.5V ~48 mΩ @ VGS = 2.5V Logic-level gate drive (works well with MCU GPIOs) Fast switching performance (ns-range switching times) Low gate charge (~6–7 nC) → efficient switching Compact SOT-23 package for space-saving PCB design Low power dissipation (~1.4W typical at 25°C ambient) Operating temperature: −55°C to +150°C Typical Applications Load switching (LEDs, sensors, small motors) Power management in battery-powered devices DC-DC converters PWM control circuits Fan and heater control in embedded systems #AO3400A #MOSFET #NChannelMOSFET #PowerElectronics #SOT23 #LoadSwitch #EmbeddedSystems #ElectronicsComponents #TrenchMOSFET #Commonpartslibrary #Transistor #FET

JST XH Connector Header Through Hole 2 position 0.098" (2.50mm) B2B-XH-A(LF)(SN) is a 2-position, 2.50 mm pitch, through-hole shrouded male PCB header from the JST XH Series. It is designed for reliable wire-to-board connections in consumer electronics, industrial equipment, power supplies, battery packs, and embedded systems. The connector features a polarized shrouded housing to prevent incorrect mating and supports secure, dependable electrical connections with easy PCB assembly. Key Features: 2-position wire-to-board header 2.50 mm contact pitch Through-hole (THT) PCB mounting Straight vertical orientation Shrouded housing with polarization to prevent misalignment Rated for up to 3 A current and 250 V AC/DC Tin-plated brass contacts for reliable conductivity Operating temperature range: -25°C to +85°C Compatible with JST XH Series crimp housings and terminals Ideal for power and signal connections in compact electronic assemblies. #JST #XHSeries #PCBHeader #WireToBoard #Connector #ThroughHole #THT #ShroudedHeader #2Position #25mmPitch #Electronics #EmbeddedSystems #IndustrialElectronics #PowerConnector #PCBDesign

Buck Switching Regulator IC Positive Fixed 3.3V 1 Output 2A SOT-23-6 Thin, TSOT-23-6 The AP63200/AP63201/AP63203/AP63205 is a 2A, synchronous buck converter with a wide input voltage range of 3.8V to 32V and fully integrates a 125mΩ high-side power MOSFET and a 68mΩ low-side power MOSFET to provide high-efficiency step-down DC/DC conversion. The AP63200/AP63201/AP63203/AP63205 device is easily used by minimizing the external component count due to its adoption of peak current mode control along with its integrated compensation network. The AP63200/AP63201/AP63203/AP63205 has optimized designs for Electromagnetic Interference (EMI) reduction. The converter features Frequency Spread Spectrum (FSS) with a switching frequency jitter of ±6%, which reduces EMI by not allowing emitted energy to stay in any one frequency for a significant period of time. It also has a proprietary gate driver scheme to resist switching node ringing without sacrificing MOSFET turn-on and turn-off times, which further erases highfrequency radiated EMI noise caused by MOSFET switching. The device is available in a low-profile, TSOT26 package. • VIN 3.8V to 32V • 2A Continuous Output Current • 0.8V ±1% Reference Voltage • 22µA Ultralow Quiescent Current • Switching Frequency o 500kHz: AP63200 and AP63201 o 1.1MHz: AP63203 and AP63205 • Pulse Width Modulation (PWM) Regardless of Output Load o AP63201 • Supports Pulse Frequency Modulation (PFM) o AP63200, AP63203, and AP63205 o Up to 80% Efficiency at 1mA Light Load o Up to 88% Efficiency at 5mA Light Load • Fixed Output Voltage o 3.3V: AP63203 o 5.0V: AP63205 • Proprietary Gate Driver Design for Best EMI Reduction • Frequency Spread Spectrum (FSS) to Reduce EMI • Precision Enable Threshold to Adjust UVLO • Protection Circuitry o Overvoltage Protection o Cycle-by-Cycle Peak Current Limit o Thermal Shutdown • 12V and 24V distributed power bus supplies • Flat screen TV sets and monitors • Power tools and laser printers • White goods and small home appliances • FPGA, DSP, and ASIC supplies • Home audios • Network systems • Set top boxes • Gaming consoles • Consumer electronics #commonpartslibrary #integratedcircuit #AP63203WU7 #BuckConverter #DCDCConverter #PowerManagement #VoltageRegulator #SynchronousBuck #EmbeddedSystems #IndustrialElectronics #PowerSupply #DiodesInc #3V3Power #ElectronicsDesign

MAX-M10 RF Receiver BeiDou, Galileo, GLONASS, GPS, GNSS 1.561GHz, 1.575GHz, 1.602GHz -167dBm 921.6kbps Not Included Module The MAX-M10S-00B is a professional-grade, ultra-low-power GNSS positioning module from u-blox based on the u-blox M10 platform. It is designed for battery-powered applications such as asset trackers, wearables, IoT devices, and navigation systems. The module supports simultaneous reception of multiple GNSS constellations, providing high positioning availability, fast acquisition times, and excellent sensitivity even in challenging urban or weak-signal environments. It integrates a TCXO, LNA, and SAW filter to improve RF performance while maintaining very low power consumption. Key Features Multi-constellation GNSS receiver: GPS Galileo GLONASS BeiDou QZSS SBAS support (WAAS, EGNOS, MSAS, GAGAN) Concurrent tracking of up to four GNSS constellations for improved position availability and accuracy. Ultra-low power consumption: Approximately 25 mW in continuous tracking mode, making it ideal for battery-powered devices. High RF sensitivity: Tracking sensitivity up to −167 dBm for reliable operation in weak-signal conditions. High positioning accuracy: Typical position accuracy of approximately 1.5 m CEP under suitable conditions. Navigation update rate: Up to 10 Hz for responsive tracking applications. Integrated RF front-end: Built-in LNA (Low Noise Amplifier) Built-in SAW filter Integrated TCXO for stable operation. Supports Assisted GNSS services: AssistNow Online AssistNow Offline AssistNow Autonomous CloudLocate support for low-power IoT positioning. Communication interfaces: UART I²C NMEA and UBX protocols supported. Wide operating temperature range: −40°C to +85°C. Supply voltage: 1.76 V to 3.6 V. Typical Applications Asset tracking devices Wearable electronics Fleet management systems Industrial IoT Smart meters Drone and robotics navigation Personal navigation devices Timing and synchronization systems Package Information Package Type: Surface-mount LCC module Dimensions: 9.7 mm × 10.1 mm × 2.5 mm (typical module size) #Commonpartslibrary #RF #Wireless #RFreceivers #MAXM10S #uBlox #GNSS #GPS #Galileo #GLONASS #BeiDou #QZSS #NavigationModule #GNSSModule #GPSTracking #AssetTracking #IoT #IndustrialIoT #WearableTech #FleetManagement #DroneNavigation #EmbeddedSystems #ElectronicsDesign #PCBDesign #HardwareEngineering #LowPowerDesign #LocationTracking #Geolocation #RFDesign #LNA #SMTModule

Bluetooth, WiFi 802.11b/g/n/ax, Bluetooth v5.4 Transceiver Module 2.4GHz Integrated, Chip Surface Mount Silicon Labs SiWG917 module is our lowest power Wi-Fi 6 plus Bluetooth LE 5.4, ideal for ultra-low power IoT wireless devices using Wi-Fi®, Bluetooth, Matter, and IP networking for secure cloud connectivity. It is optimal for developing battery operated devices that need long battery life. SiWG917 module includes an ultra-low power Wi-Fi 6 plus Bluetooth Low Energy (LE) 5.4 wireless CPU subsystem, and an integrated micro-controller (MCU) application subsystem, security, peripherals and power management subsystem all in a single 16 x 21.1 x 2.3 mm package. The wireless subsystem consists of a multi-threaded Network Wireless Processor (NWP) running up to 160 MHz, baseband digital signal processing, analog front end, 2.4 GHz RF transceiver and integrated power amplifier. The application subsystem consists of an ARM® Cortex®-M4 running up to 180 MHz, embedded SRAM, flash, ultra-low power sensor hub, and matrix vector processor. The ARM® Cortex®-M4 is dedicated for peripheral and application-related processing, while the NWP runs the wireless and networking stacks on independent threads, thus providing a fully integrated solution that is ready for a wide range of embedded wireless IoT applications. The modules come with modular radio type approvals for various countries, including USA (FCC), Canada (IC/ISED) and Japan (MIC), and are in compliance with the relevant EN standards (including EN 300 328 v2.2.2) for the conformity with the directives and regulations in EU and UK. KEY FEATURES • Wi-Fi 6 Single Band 2.4 GHz 20 MHz 1x1 stream IEEE 802.11 b/g/n/ax • Bluetooth LE 5.4 • Single chip Matter Over Wi-Fi Solution • ARM® Cortex® M4 Processor with FPU subsystem up to 180 MHz with rich set of Digital and Analog Peripherals. • Wi-Fi 6 Benefits: TWT for improved efficiency and longer battery life, MUMIMO/OFDMA for Higher Throughput, network capacity and low latency • Best in Class Device and Wireless Security • WLAN Tx power up to +17.5 dBm with integrated PA • Bluetooth LE Tx power up to +17 dBm with integrated PA • WLAN Rx sensitivity as low as -95.5 dBm • Wi-Fi 4 Standby Associated mode current: 71 μA @ 1-second listen interval • Embedded Flash option up to 8 MB/ optional external Flash up to 16 MB • Embedded PSRAM option up to 2 MB/ optional external PSRAM option up to 16 MB • Ultra-low power sensor hub peripherals • Matrix Vector Processor (MVP) • Embedded Wi-Fi, Bluetooth LE, Matter, and networking stacks supporting wireless coexistence • Three software-configurable MCU application memory options for sharing the RAM between the wireless, system, and application (192/256/320 KB) • Operating temperature: -40 to +85 ºC • Operating supply range: 3.0 to 3.63 V • Supply voltage for GPIOs: 1.71 to 3.63 V #WiFi6 #BluetoothLE54 #IoTModule #WirelessSoC #SiliconLabs #EmbeddedSystems #SmartHome #IndustrialIoT #LowPowerDesign #RFModule #ConnectedDevices #EdgeComputing #MatterReady #PCBDesign #ElectronicsEngineering

MPU with Dual Arm Cortex-A35 @1.5GHz, Cortex-M33 @400MHz, 3xEthernet (2+1 switch), 3xFD-CAN, LVDS/DSI, H.264, 3D GPU, AI/NN, Secure Boot, Cryptography, DRAM enc/dec, PKA The STM32MP257FAI3 is a high-performance microprocessor from STMicroelectronics' STM32MP2 series, integrating dual 64-bit Arm Cortex-A35 cores running at up to 1.5 GHz, a Cortex-M33 real-time core, and a Cortex-M0+ low-power management core. It is designed for advanced industrial, edge AI, machine vision, HMI, IoT gateway, and multimedia applications requiring Linux-class processing alongside deterministic real-time control. The device features AI acceleration, 3D graphics, video encoding/decoding, extensive connectivity, advanced security, and support for high-speed external memory. Key Features Dual-core 64-bit Arm Cortex-A35 CPU operating up to 1.5 GHz Arm Cortex-M33 real-time processor with TrustZone and FPU support Arm Cortex-M0+ low-power coprocessor for autonomous operation Integrated NPU (Neural Processing Unit) delivering up to 1.35 TOPS AI performance 3D GPU and hardware video encoder/decoder acceleration Supports DDR3L, DDR4, and LPDDR4 external memory up to 4 GB Multiple display interfaces including MIPI-DSI, LVDS, and parallel RGB USB 2.0 Host and USB 3.0 Dual-Role with embedded PHYs PCI Express interface with integrated 5 Gbps PHY Up to three Gigabit Ethernet interfaces with TSN and IEEE 1588 support Extensive connectivity: I2C, I3C, SPI, UART, USART, CAN FD, SDMMC, SAI, and SPDIF Hardware cryptographic accelerators including AES, SHA, RSA, ECC, PKA, and True RNG Secure boot, TrustZone security, tamper detection, and resource isolation framework Multiple low-power operating modes for energy-efficient designs Available in fine-pitch BGA packages for high-density embedded systems. #STM32MP257FAI3 #STM32MP2 #STMicroelectronics #CortexA35 #CortexM33 #EdgeAI #EmbeddedLinux #IndustrialAutomation #MachineVision #HMI #IoTGateway #MPU #PCIe #USB3 #GigabitEthernet #TrustZone #EmbeddedSystems #ArtificialIntelligence #LinuxProcessor #IndustrialIoT #CommonPartsLibrary #IntegratedCircuit #Microprocessor #STM32MP2

1/1 Transceiver Half RS422, RS485 8-SOIC These devices have robust 3.3-V drivers and receivers in a small package for demanding industrial applications. The bus pins are robust to ESD events with high levels of protection to Human-Body Model and IEC Contact Discharge specifications. Each of these devices combines a differential driver and a differential receiver which operate from a single 3.3-V power supply. The driver differential outputs and the receiver differential inputs are connected internally to form a bus port suitable for half-duplex (two-wire bus) communication. These devices feature a wide common-mode voltage range making the devices suitable for multi-point applications over long cable runs. These devices are characterized from –40°C to 125°C 1• Small-size VSSOP Packages Save Board Space, or SOIC for Drop-in Compatibility • Bus I/O Protection – >±15 kV HBM Protection – >±12 kV IEC 61000-4-2 Contact Discharge – >±4 kV IEC 61000-4-4 Fast Transient Burst • Extended Industrial Temperature Range –40°C to 125°C • Large Receiver Hysteresis (80 mV) for Noise Rejection • Low Unit-Loading Allows Over 200 Connected Nodes • Low Power Consumption – Low Standby Supply Current: < 2 µA – ICC < 1 mA Quiescent During Operation • 5-V Tolerant Logic Inputs Compatible With 3.3-V or 5-V Controllers • Signaling Rate Options Optimized for: 250 kbps, 20 Mbps, 50 Mbps • Glitch Free Power-Up and Power-Down Bus Inputs and Outputs 2 Applications • Factory Automation • Telecommunications Infrastructure • Motion Control #SN65HVD75D #RS485 #RS422 #Transceiver #TexasInstruments #IndustrialCommunication #FactoryAutomation #MotionControl #TelecomInfrastructure #ESDProtection #HalfDuplex #InterfaceIC #EmbeddedSystems #IndustrialElectronics #DataCommunication

Bipolar Motor Driver NMOS On/Off, PWM 44-HTSSOP The DRV8262QDDWRQ1 is an automotive-qualified, high-power H-bridge motor driver from Texas Instruments designed for 24 V and 48 V automotive systems. It integrates two H-bridges capable of driving one or two brushed DC motors, a bipolar stepper motor, or thermoelectric coolers (TECs). The device features integrated high-side current sensing, programmable current regulation, and comprehensive protection functions, eliminating the need for external current-sense resistors while reducing PCB area and system cost. It supports wide supply voltages from 4.5 V to 60 V, making it suitable for demanding automotive body electronics and industrial motor control applications. Key Features Automotive AEC-Q100 Grade 1 qualified (-40°C to +125°C) Wide 4.5 V to 60 V operating supply voltage Dual H-bridge or single high-current H-bridge operation Drives: One or two brushed DC motors One bipolar stepper motor One or two thermoelectric coolers (TECs) Up to 8 A peak (dual H-bridge mode) Up to 16 A peak (single H-bridge mode) Low MOSFET on-resistance: 100 mΩ (dual H-bridge) 50 mΩ (single H-bridge) Integrated high-side current sensing with ±4% accuracy Programmable current regulation and current limiting Supports 1.8 V, 3.3 V, and 5 V logic interfaces Configurable PWM control modes (PH/EN or IN/IN) Ultra-low 3 µA sleep current Integrated protection features: Undervoltage Lockout (UVLO) Charge Pump Undervoltage (CPUV) Overcurrent Protection (OCP) Thermal Shutdown (OTSD) Fault output (nFAULT) Functional safety-capable with supporting documentation for automotive system design. #DRV8262QDDWRQ1 #MotorDriver #HBridge #AutomotiveElectronics #BrushedDCMotor #StepperMotor #CurrentSense #AECQ100 #TexasInstruments #EmbeddedSystems #PowerManagement #PCBDesign

Power Switch/Driver 1:1 N-Channel 1.35A 28-WQFN (4x5) The TPS274160 device is a smart high-side switch with four integrated 160-mΩ NMOS power FETs and a chargepump to drive the gates. The device offers robust protection and diagnostic features to drive various loads (inductive, capacitive, and resistive) such as low wattage bulbs, LEDs, relays, solenoids, heaters, and sub-modules. The part enables flexible, multi-channel output configurations through paralleling channels and is in a very small WQFN package to enable usage in space constrained applications. The device is protected against short circuit events and over-temperature events, safely shutting off the output during fault events. The device also implements an external adjustable current limiting feature. This feature improves the reliability of the system by reducing inrush current when driving large capacitive loads and minimizing overload current thereby eliminating system supply brown out condition. The device also integrates diagnostic features like output current monitoring (version B) and open load detection to enable improved intelligence in modules and to enable predictive maintenance functionality. • Quad-channel 160-mΩ smart high-side switch • Wide DC operating voltage range: 5 V to 36 V – 50-V absolute maximum voltage • Accurate adjustable current limiting (250 mA to 4 A) • Intelligent diagnostic features – TPS274160A: Open-drain fault output – TPS274160B: Analog current sense – Open-load or short to supply detection in the off-state • Robust protection features – Short-circuit protection – Inductive load flyback clamp – Undervoltage lockout (UVLO) protection – Loss of GND protection • Excellent ESD protection on VS and OUT pins – ±8/±15 kV IEC 61000-4-2 ESD contact/air discharge • Available in small and 28-pin leadless QFN packages • Functional Safety-Capable – Documentation available to aid functional safety system design 2 Applications • Digital output modules • Standalone remote I/O • Motor drives • Solenoid or valve drive #TexasInstruments #TPS274160BRLHR #HighSideSwitch #SmartSwitch #IndustrialAutomation #PowerManagement #LoadDriver #CurrentLimiting #ProtectionIC #IndustrialControl #RemoteIO #SolenoidDriver #MotorDrive #EmbeddedSystems #ElectronicsDesign

ARM® Cortex®-M4F STM32G4 Microcontroller IC 32-Bit 170MHz 512KB (512K x 8) FLASH 64-LQFP (10x10) The STM32G491RET6 from STMicroelectronics is a high-performance 32-bit microcontroller based on the Arm® Cortex®-M4 core with Floating Point Unit (FPU), designed for advanced embedded applications requiring high computational performance, precise analog processing, and real-time control. It belongs to the STM32G4 series and integrates enhanced analog peripherals, motor-control timers, communication interfaces, security features, and hardware accelerators such as CORDIC and FMAC. The device operates at up to 170 MHz, provides 512 KB Flash memory, and includes 96 KB SRAM, making it suitable for applications such as motor control, digital power conversion, industrial automation, robotics, and embedded control systems. Key Features Core: Arm® Cortex®-M4 32-bit CPU with FPU, DSP instructions, and MPU Maximum CPU Frequency: Up to 170 MHz (up to 213 DMIPS) Memory: 512 KB Flash memory with ECC support 96 KB SRAM with parity checking features Quad-SPI memory interface Operating Voltage: 1.71 V to 3.6 V Package: LQFP-64 Advanced Analog Features: 3 × 12-bit ADCs with high-speed conversion 4 × 12-bit DAC channels 4 × Rail-to-Rail operational amplifiers 4 × Fast analog comparators Internal voltage reference buffer Hardware Accelerators: CORDIC accelerator for trigonometric calculations FMAC (Filter Math Accelerator) for digital filtering applications Timers & Motor Control: Advanced PWM timers for motor-control applications Multiple 16-bit and 32-bit timers Support for encoder and PWM control Communication Interfaces: 2 × FDCAN interfaces 5 × USART/UART 3 × SPI interfaces 3 × I²C interfaces USB 2.0 Full-Speed interface SAI audio interface Security Features: True Random Number Generator (TRNG) CRC calculation unit Unique device ID Debug & Programming: SWD and JTAG debugging support Typical Applications Motor control and BLDC controllers Digital power converters Industrial automation equipment Robotics and motion control Smart sensors and embedded control systems Power management applications #STM32G491RET6 #STM32G4 #STMicroelectronics #ARM_CortexM4 #Microcontroller #MCU #EmbeddedSystems #MotorControl #DigitalPower #IndustrialAutomation #Robotics #IoT #ElectronicsDesign #PCBDesign

Accelerometer, Gyroscope, Magnetometer, 9 Axis Sensor I2C, SPI, UART Output The BNO085 is a high-performance 9-axis absolute orientation sensor system-in-package (SiP) that integrates a 3-axis accelerometer, 3-axis gyroscope, 3-axis magnetometer, and a low-power ARM Cortex-M0+ microcontroller running CEVA/Hillcrest SH-2 sensor fusion firmware. It provides accurate real-time orientation, motion tracking, and activity detection while offloading complex sensor fusion calculations from the host processor. The device is widely used in robotics, AR/VR systems, wearables, drones, IoT devices, and navigation applications. Key Features 9-axis motion sensing with integrated accelerometer, gyroscope, and magnetometer Built-in SH-2 sensor fusion engine for accurate orientation tracking ARM Cortex-M0+ processor for onboard motion processing Outputs quaternion, rotation vector, linear acceleration, gravity vector, angular velocity, and magnetic field data Advanced motion detection including tap, step, shake, and significant motion detection Activity classification and stability detection capabilities Low-latency rotation vectors optimized for AR/VR applications Supports I²C, SPI, and UART communication interfaces Configurable output data rates and timestamps Low-power operation suitable for battery-powered devices Compact 28-pin LGA package (5.2 mm × 3.8 mm) Operating temperature range: -40°C to +85°C Backward compatible with BNO080 designs while adding support for future application-specific libraries Applications Robotics and autonomous systems Virtual Reality (VR) and Augmented Reality (AR) Wearable devices and fitness trackers Drones and UAVs Head-mounted displays (HMDs) Industrial motion tracking IoT and smart devices Navigation and positioning systems #BNO085 #IMU #9AxisSensor #MotionTracking #SensorFusion #OrientationSensor #Robotics #AR #VR #IoT #Wearables #EmbeddedSystems #CEVA #HillcrestLabs #MotionDetection #Quaternion #InertialMeasurementUnit

9 Position D-Sub Receptacle, Female Sockets Connector 2311765-1 is a 9-position right-angle D-Sub receptacle connector from the TE Connectivity AMPLIMITE HD-20 series. It is designed for wire-to-board signal applications and features through-hole PCB mounting with an integrated boardlock and 4-40 screwlock for secure mechanical retention. The connector is commonly used in industrial equipment, communication systems, embedded controllers, and other electronic devices requiring a reliable D-Sub interface. Key Features 9-position D-Sub receptacle (female) Right-angle through-hole PCB mounting AMPLIMITE HD-20 series 2-row configuration 2.77 mm (0.109") contact pitch Boardlock for improved PCB retention 4-40 screwlock for secure mating Maximum contact current: 3 A per contact Glass-filled PBT housing Operating temperature: -55°C to +85°C Ideal for signal transmission in industrial and embedded applications. #CommonPartsLibrary #Connector #TEConnectivity #AMPLIMITE #DSub #RightAngleConnector #PCBConnector #ThroughHole #WireToBoard #SignalConnector #ElectronicComponents #EmbeddedSystems