Power Management IC (PMIC) integrating battery charging, power regulation, fuel gauging, and system management for single-cell Li-ion, Li-poly, and LiFePO₄ batteries. It features a 4–100 mA linear battery charger, two 200 mA buck regulators, two configurable 50 mA LDOs or 100 mA load switches, USB-C compatible input (4.0–5.5 V) with 22 V overvoltage protection, and an I²C-compatible TWI interface with watchdog, hard reset, power-loss warning, GPIOs, and LED drivers. #PMIC #PowerManagementIC #BatteryCharger #FuelGauge #BuckRegulator #LDO #USBTypeC #I2C #TWI #NordicSemiconductor #LiIon #LiPo #LiFePO4

Lipo battery charger with 3v3 @ 1.8A output.

Plug Power Connectors The XT60U-M is a high-current 2-pin male DC power connector from the XT60 series, commonly manufactured by AMASS. It is widely used in RC batteries, drones, e-bikes, battery packs, power distribution systems, and other applications that require reliable high-current connections. The connector uses gold-plated brass contacts and a flame-retardant polyamide housing to provide low contact resistance, durability, and safe operation under high loads. Key Features Connector Type: XT60 series male plug Number of Pins: 2 Rated Current: 30 A continuous Rated Voltage: 500 V DC Contact Material: Gold-plated brass Housing Material: Polyamide (PA), UL94 V-0 flame-retardant Wire Size Support: Up to 12 AWG Mounting Method: Cable mount, solder termination Mechanical Life: Approximately 1000 mating cycles Operating Temperature Range: −20 °C to +120 °C Low Contact Resistance for efficient power transfer Polarized Design prevents reverse connection and incorrect mating Compact and Lightweight construction for battery-powered systems Typical Applications RC LiPo battery packs Drones and UAVs Electric bicycles and scooters Robotics projects Portable power systems Battery chargers and power distribution modules #CommonPartsLibrary #Connector

Single LiPo battery fuel gauge, I2C, type 01, WDFN-8 Battery gauge I2C WDFN*1EP*4x3mm*P0.65mm*

The Boron is a powerful LTE Cat M1 enabled development kit that supports cellular networks and Bluetooth LE (BLE). It is based on the Nordic nRF52840 and has built-in battery charging circuitry so it’s easy to connect a Li-Po and deploy your local network in minutes. #commonpartslibrary #developmentboard #boron

1.5A USB-Friendly Li-Ion Battery Charger and Power-Path Management IC with 4.2 VBAT The BQ24075TRGTR (from Texas Instruments) is a highly integrated single-cell Li-Ion / Li-Polymer linear battery charger IC with power-path management. It is designed for portable and space-constrained applications, allowing a device to be powered from a USB port or AC adapter while simultaneously charging the battery. The device integrates charging control, power-path management, and safety features into a compact package. A key feature is its Dynamic Power Path Management (DPPM), which ensures the system is powered even when the battery is low or absent, while intelligently managing charging current. Key Features Battery Charging Supports single-cell Li-Ion / Li-Polymer batteries Up to 1.5 A programmable charge current Three-phase charging: Pre-charge (conditioning) Constant current Constant voltage Fixed 4.2 V charge voltage Power Path Management Dynamic Power Path Management (DPPM): Powers system and charges battery simultaneously Prioritizes system load over charging Allows system operation even with: Deeply discharged battery No battery connected Input & Power Features Operates from: USB input (100 mA / 500 mA selectable) AC adapter Programmable input current limit up to 1.5 A Input voltage range: ~4.35 V to 6.4 V (28 V max rating) Input dynamic power management (VIN-DPM) prevents source overload Protection & Safety Thermal regulation and shutdown Over-voltage protection (OVP) Short-circuit and reverse current protection Battery temperature monitoring (NTC thermistor input) Battery disconnect (SYSOFF) feature Control & Status Standalone operation (no MCU required, resistor-programmable) Charge status outputs: Charging Charge complete Power good Physical Characteristics Package: 16-pin VQFN (3 mm × 3 mm) Operating temperature: –40°C to +85°C #commonpartslibrary #integratedcircuit #powermanagement #batterycharger

Battery Power Management IC Lithium Ion/Polymer 24-QFN (4x4) nPM1100 is an integrated Power Management IC (PMIC) with a linear-mode lithium-ion/lithium-polymer battery charger in a compact 2.1x2.1 mm WLCSP package. It has a highly efficient, dual-mode configurable output DC/DC buck regulator. nPM1100 is an extremely compact PMIC device, created for space constrained applications with a small lithium-ion or lithium-polymer battery. It is compatible with all nRF52 and nRF53 Series SoCs and supports charging batteries at up to 500 mA through USB, and also delivers up to 150 mA of current to power external components with regulated voltage. A minimum of five passive components are required for operation and the device functions without a control interface. It is the perfect companion for nRF52 and nRF53 multiprotocol SoCs in battery powered designs. Low quiescent current (IQ) extends battery life during shipping and storage with Ship mode, or in operation using auto-controlled hysteretic buck mode for high efficiency down to 1 µA loads. Charge and error indication LED drivers are built in. Charge profile limits are configurable and VBUS current limits can be fixed or auto-controlled with on-chip USB port detection. • 400 mA linear battery charger • Linear charger for lithium-ion/lithium-polymer batteries • Adjustable charge current from 20 mA to 400 mA • Selectable termination voltage of 4.1 V or 4.2 V • Automatic trickle, constant current, and constant voltage charging • Battery thermal protection • Discharge current limitation • JEITA compliant • Li-ion/Li-polymer USB battery charger with a high efficiency buck regulator • 800 nA - Typical quiescent current • 460 nA - Shipping mode quiescent current • Thermal protection • Input regulator • USB compatible current limit of 100 mA and 500 mA • 4.1 V to 6.7 V input voltage range for normal operation • 20 V overvoltage protection • Reverse current protection • 3.0 V to 5.5 V system voltage output • USB port detection supporting the following types: • SDP • CDP/DCP • 1.8 V to 3.0 V, 150 mA step-down buck regulator • Step-down buck regulator with up to 92% efficiency • Automatic transition between hysteretic and pulse width modulation (PWM) modes • Forced PWM mode for clean power operation • Pin-selectable output voltage (1.8 V, 2.1 V, 2.7 V, 3.0 V) • Soft start-up • LED drivers for charger state indication • 5 mA low side LED driver for charging indication • 5 mA low side LED driver for error indication • 2.3 V to 4.35 V battery operating input range • 2.1x2.1 mm WLCSP package • Suitable for two layer PCB design #CommonPartsLibrary #IntegratedCircuit #NordicSemiconductor #nPM1100 #PMIC #BatteryCharger #PowerManagement #LiIon #LiPolymer #BuckConverter #Wearables #IoT #WirelessSensor #LowPowerDesign #USBCharging #EmbeddedSystems #nRF52 #nRF53 #PortableElectronics