Part Review and Datasheet Update

flux

Reviewed the NPM1100-QDAA-R7 part metadata, symbol pins, and footprint against Nordic’s nPM1100 documentation. I recorded the official Nordic datasheet URL in project metadata and created the detailed review here: part-review-npm1100-qdaa-r7.
Open items / mismatches:
  • Pin 3 is labeled VOUTBSET2; latest Nordic docs say it should be VOUTBSET0.
  • Pin 4 is labeled NC_1; latest Nordic docs say it should be AVSS ground.
  • Exposed pad is labeled GND; datasheet names it AVSS — electrically OK, but naming should be clarified.
  • Pin types/descriptions are mostly unspecified and should be populated from the datasheet.
Suggested next steps:
  1. Rename/fix the mismatched terminals.
  2. Populate pin descriptions and pin types from the datasheet.
  3. Re-check the footprint pad geometry against the QFN-24 4×4 mm exposed-pad land pattern.
A

adrian95

Fix the pin mismatches, populate pin descriptions, and pin type then run a symbol/footprint review.

flux

I’ll correct the mismatched NPM1100-QDAA-R7 pins, populate pin descriptions/types from the Nordic QFN24 pin table, then run a fresh schematic/footprint review.

flux

I found the three symbol naming mismatches still present: pin 3, pin 4, and the exposed pad label. I’m applying the corrected Nordic QFN24 names and descriptions now.

flux

Updated the symbol/footprint pin labels and metadata: VOUTBSET2 → VOUTBSET0, NC_1 → AVSS, and exposed pad GND → AVSS_EP. I populated all 25 terminals with datasheet-based pin descriptions and Flux-valid pin types, then reviewed the symbol/footprint checks; no open warnings/errors were reported.
Open items:
  • The exposed pad is named AVSS_EP to avoid duplicate AVSS labels while preserving datasheet meaning.
  • Pad geometry dimensions were not exposed in the review output, so only pad naming/count consistency was verified.
Suggested next steps:
  1. If desired, import/check the exact Nordic QFN-24 4×4 mm land pattern dimensions.
  2. Publish the corrected part revision.
Check land pattern and publish
Check land pattern
Run full review
Publish revision
Update review document
Sign up to send

Files

Pins

Symbol

Layout

3D View

ICHG
Pin Number
12
SHPACT
Pin Number
6
VBAT
Pin Number
15
D+
Pin Number
20
VOUTB
Pin Number
1
NC_4
Pin Number
24
CHG
Pin Number
8
VOUTBSET1
Pin Number
2
VBUS
Pin Number
17
VOUTBSET0
Pin Number
3
PVSS
Pin Number
23
MODE
Pin Number
7
ISET
Pin Number
5
SHPHLD
Pin Number
11
NC_2
Pin Number
13
NC_3
Pin Number
18
VTERMSET
Pin Number
9
NTC
Pin Number
14
ERR
Pin Number
10
AVSS_EP
Pin Number
25
VSYS
Pin Number
16
DEC
Pin Number
21
AVSS
Pin Number
4
SW
Pin Number
22
D-
Pin Number
19
Name
Pin #
Type
Section
Pin Group
Orientation
Order
Sub-symbol
Pin Description
VOUTB
1
Power Out
BUCK regulator output
VOUTBSET1
2
Bi-Directional
BUCK regulator output voltage selection bit 1; toggle only in Power OFF
VOUTBSET0
3
Bi-Directional
BUCK regulator output voltage selection bit 0; toggle only in Power OFF
AVSS
4
Ground
Bottom
Analog ground / AVSS
ISET
5
Input
VBUS current limit selection: 100 mA SDP-only or 500 mA
SHPACT
6
Input
Shipping mode activate input
MODE
7
Input
BUCK mode select: LOW automatic, HIGH forced PWM
CHG
8
Open Collector
Open-drain low-side LED driver; active when battery is charging
VTERMSET
9
Input
Battery charge termination voltage select: LOW 4.10 V, HIGH 4.20 V
ERR
10
Open Collector
Open-drain low-side LED driver; active on charging error condition
SHPHLD
11
Input
Shipping mode hold input
ICHG
12
Input
Charge current limit resistor input
NC_2
13
Not Connected
No connect
NTC
14
Input
Battery NTC thermistor input
VBAT
15
Power In
Battery connection
VSYS
16
Power Out
System voltage output; enabled after power-on reset; do not externally supply
VBUS
17
Power In
Input supply from USB or adapter
NC_3
18
Not Connected
No connect
D-
19
Input
USB D- data line for port detection
D+
20
Input
USB D+ data line for port detection
DEC
21
Power Out
System decoupling capacitor pin; do not externally supply
SW
22
Power Out
BUCK converter switching node to inductor
PVSS
23
Ground
DC/DC power ground

NPM1100-QDAA-R7