Buck Switching Regulator IC Positive Adjustable 1.2V 1 Output 3.5A 8-PowerSOIC (0.154", 3.90mm Width) The LM5013DDAR is a 100-V input, 3.5-A buck switching regulator IC that efficiently steps down high DC voltages (such as 24 V, 48 V, or battery rails) to lower regulated outputs. It is optimized for rugged environments where wide input variations and high reliability are required. It features ultra-low quiescent current operation, making it suitable for systems that require high efficiency even at light load or standby conditions. Key Features Wide input voltage range: 6 V to 100 V Up to 3.5 A output current capability Integrated 100-V high-side MOSFET Non-synchronous buck topology Ultra-low quiescent current (IQ) for high efficiency in standby Constant-on-time (COT) control for fast transient response No external compensation components required Adjustable output voltage (down to ~1.2 V reference) 50 ns minimum on/off time for high step-down ratios Built-in protection features: Overcurrent protection Thermal shutdown Input undervoltage lockout (UVLO) Open-drain power-good (PGOOD) signal for system monitoring Meets low EMI requirements (CISPR 25 Class 5 capable) Package 8-pin SO PowerPAD (DDA) surface-mount package Designed for good thermal performance in high-voltage applications Typical Applications Industrial power supplies (24 V / 48 V systems) Automotive power systems Telecom and networking equipment High cell-count battery systems Motor control and inverter subsystems #LM5013 #BuckConverter #DCDCConverter #TexasInstruments #PowerManagementIC #HighVoltageRegulator #3ARegulator #IndustrialPower #AutomotiveElectronics #SwitchingRegulator #COTController

Buck Switching Regulator IC Positive Fixed 3.3V 1 Output 2A SOT-23-6 Thin, TSOT-23-6 The AP63200/AP63201/AP63203/AP63205 is a 2A, synchronous buck converter with a wide input voltage range of 3.8V to 32V and fully integrates a 125mΩ high-side power MOSFET and a 68mΩ low-side power MOSFET to provide high-efficiency step-down DC/DC conversion. The AP63200/AP63201/AP63203/AP63205 device is easily used by minimizing the external component count due to its adoption of peak current mode control along with its integrated compensation network. The AP63200/AP63201/AP63203/AP63205 has optimized designs for Electromagnetic Interference (EMI) reduction. The converter features Frequency Spread Spectrum (FSS) with a switching frequency jitter of ±6%, which reduces EMI by not allowing emitted energy to stay in any one frequency for a significant period of time. It also has a proprietary gate driver scheme to resist switching node ringing without sacrificing MOSFET turn-on and turn-off times, which further erases highfrequency radiated EMI noise caused by MOSFET switching. The device is available in a low-profile, TSOT26 package. • VIN 3.8V to 32V • 2A Continuous Output Current • 0.8V ±1% Reference Voltage • 22µA Ultralow Quiescent Current • Switching Frequency o 500kHz: AP63200 and AP63201 o 1.1MHz: AP63203 and AP63205 • Pulse Width Modulation (PWM) Regardless of Output Load o AP63201 • Supports Pulse Frequency Modulation (PFM) o AP63200, AP63203, and AP63205 o Up to 80% Efficiency at 1mA Light Load o Up to 88% Efficiency at 5mA Light Load • Fixed Output Voltage o 3.3V: AP63203 o 5.0V: AP63205 • Proprietary Gate Driver Design for Best EMI Reduction • Frequency Spread Spectrum (FSS) to Reduce EMI • Precision Enable Threshold to Adjust UVLO • Protection Circuitry o Overvoltage Protection o Cycle-by-Cycle Peak Current Limit o Thermal Shutdown • 12V and 24V distributed power bus supplies • Flat screen TV sets and monitors • Power tools and laser printers • White goods and small home appliances • FPGA, DSP, and ASIC supplies • Home audios • Network systems • Set top boxes • Gaming consoles • Consumer electronics #commonpartslibrary #integratedcircuit #AP63203WU7 #BuckConverter #DCDCConverter #PowerManagement #VoltageRegulator #SynchronousBuck #EmbeddedSystems #IndustrialElectronics #PowerSupply #DiodesInc #3V3Power #ElectronicsDesign

Buck Switching Regulator IC Positive Adjustable 0.8V 1 Output 3.5A SOT-23-6 Thin, TSOT-23-6 The LMR51635YFDDCR specification defines the engineering requirements for a synchronous step-down DC-DC converter integrated circuit designed for high-efficiency power regulation in embedded and industrial electronic systems. This specification establishes the functional, electrical, mechanical, thermal, environmental, and quality requirements necessary to ensure stable voltage conversion, efficient power management, and long-term operational reliability. The device is intended for use in industrial automation, telecommunications equipment, consumer electronics, test and measurement instruments, distributed power systems, and embedded applications requiring regulated low-voltage power rails from higher-voltage DC sources. It integrates high-performance switching circuitry to provide efficient voltage conversion while minimizing external component count and overall system power loss. Engineering Requirements The DC-DC converter shall be manufactured using qualified semiconductor fabrication processes and high-quality materials to ensure consistent electrical performance, low power consumption, and reliable long-term operation. The device shall maintain stable functionality under specified input voltage, output load, temperature, and environmental operating conditions. Electrical characteristics shall provide accurate output voltage regulation, high conversion efficiency, low output ripple, and fast transient response during load and input voltage variations. The converter shall maintain stable switching operation while supporting continuous and dynamic power delivery with minimal performance degradation. The integrated control architecture shall ensure reliable startup, controlled shutdown, and stable operation under varying load conditions. Built-in protection mechanisms shall support safe operation during abnormal conditions, including overload, overcurrent, thermal stress, and short-circuit events, thereby enhancing overall system reliability. Thermal performance shall support continuous operation within the specified junction temperature range while maintaining electrical integrity and long-term reliability. The package shall be suitable for automated surface-mount assembly and compatible with standard solder reflow manufacturing processes. Mechanical construction shall withstand thermal cycling, vibration, mechanical handling, and environmental exposure without degradation of electrical or mechanical performance. Workmanship shall be free from defects including contamination, package cracking, bond failures, lead deformation, or structural inconsistencies that could adversely affect device functionality or reliability. Inspection, validation, and testing shall be conducted using calibrated equipment and controlled quality procedures to verify compliance with engineering and manufacturing requirements. Any deviation from this specification shall require formal engineering evaluation, documented technical justification, and approval through the established engineering change control process before implementation. Documentation Supporting documentation shall include engineering drawings, electrical performance specifications, application guidelines, thermal characterization reports, qualification records, inspection reports, reliability data, material declarations, and revision-controlled manufacturing documentation. All documentation shall be maintained under formal configuration management and quality assurance systems to ensure complete product traceability. Revision Control Any modification to this specification shall be managed through the formal engineering change management process. All revisions shall undergo technical review, validation, and approval before release to ensure continued compliance with design intent and applicable engineering standards. #EngineeringSpecification #DCDCConverter #BuckConverter #PowerManagement #PowerElectronics #EmbeddedSystems #IndustrialElectronics #VoltageRegulator #QualityAssurance #EngineeringDocumentation

10 µH Shielded Drum Core, Wirewound Inductor 7.5 A 30mOhm Max Nonstandard # Engineering Specification ## Product Name SRP1038A-100M ## General Description SRP1038A-100M is a shielded surface mount power inductor designed for use in high-efficiency DC-DC conversion and power management applications. The device is intended to support energy storage and current smoothing functions in switching regulator circuits, where stable inductance performance and low power loss are critical. The inductor utilizes a ferrite core construction with a shielded magnetic structure to minimize electromagnetic interference and reduce magnetic flux leakage. This enables improved circuit density and reduced noise coupling in compact electronic assemblies. The design is optimized for use in high current power conversion systems, including buck converters, point-of-load regulators, and distributed power architectures. The component is widely used in industrial, automotive, telecommunications, and embedded systems where reliable energy transfer, thermal stability, and efficient power delivery are required. Its surface mount form factor supports automated PCB assembly and compact system integration while maintaining mechanical robustness under thermal and electrical stress. The design emphasizes low direct current resistance, high current handling capability, and stable inductance behavior under load conditions. It is suitable for applications requiring efficient power conversion with minimal energy loss and stable electromagnetic performance. ## Functional Requirements ### Energy Storage The device shall store energy in a magnetic field during switching operation in power conversion circuits. ### Current Filtering The device shall smooth current ripple in switching regulator applications to maintain stable output conditions. ### Electromagnetic Shielding The device shall reduce electromagnetic interference through a shielded magnetic structure. ### Power Conversion Support The component shall support efficient operation in DC-DC conversion systems. ## Electrical Requirements ### Inductive Performance The device shall provide stable inductance characteristics suitable for power conversion and filtering applications. ### Low Loss Operation The inductor shall minimize resistive and core losses to improve overall system efficiency. ### High Current Capability The device shall support operation under elevated current conditions typical of switching power supplies. ### Thermal Stability The inductor shall maintain performance consistency under thermal loading and temperature variation. ## Mechanical Requirements ### Surface Mount Package The device shall be supplied in a surface mount configuration suitable for automated PCB assembly processes. ### Structural Integrity The component shall withstand mechanical stress during assembly, operation, and thermal cycling. ### PCB Integration The design shall support compact layout integration in multilayer printed circuit board systems. ## Environmental Requirements ### Operating Conditions The device shall operate reliably under conditions typical of industrial and embedded electronic systems. ### Thermal Performance The component shall maintain stable operation under continuous power cycling and heat generation. ### Storage and Handling The device shall retain structural and electrical integrity during storage, transportation, and handling. ## Quality Requirements ### Reliability The inductor shall provide consistent long-term performance under continuous electrical and thermal stress. ### Verification Electrical and thermal characteristics shall be validated through appropriate qualification and testing procedures. ### Compliance The product shall conform to applicable standards for magnetic components used in power electronics applications. ## Documentation Requirements Technical documentation shall include application guidance, layout recommendations for switching power designs, thermal considerations, electrical characteristics, and integration practices for DC-DC converter systems. ## Classification Tags #SRP1038A100M #PowerInductor #ShieldedInductor #SMDInductor #MagneticComponent #EnergyStorageInductor #DCDCConverter #BuckConverter #PowerElectronics #SMPSDesign #ElectromagneticCompatibility #EMIShielding #PCBDesign #ElectricalEngineering #EmbeddedPower #IndustrialElectronics #AutomotiveElectronics #CommonPartsLibrary #ComponentLibrary #EngineeringSpecification #PowerManagement #CircuitDesign #HighCurrentInductor

Battery Power Management IC Lithium Ion/Polymer 24-QFN (4x4) nPM1100 is an integrated Power Management IC (PMIC) with a linear-mode lithium-ion/lithium-polymer battery charger in a compact 2.1x2.1 mm WLCSP package. It has a highly efficient, dual-mode configurable output DC/DC buck regulator. nPM1100 is an extremely compact PMIC device, created for space constrained applications with a small lithium-ion or lithium-polymer battery. It is compatible with all nRF52 and nRF53 Series SoCs and supports charging batteries at up to 500 mA through USB, and also delivers up to 150 mA of current to power external components with regulated voltage. A minimum of five passive components are required for operation and the device functions without a control interface. It is the perfect companion for nRF52 and nRF53 multiprotocol SoCs in battery powered designs. Low quiescent current (IQ) extends battery life during shipping and storage with Ship mode, or in operation using auto-controlled hysteretic buck mode for high efficiency down to 1 µA loads. Charge and error indication LED drivers are built in. Charge profile limits are configurable and VBUS current limits can be fixed or auto-controlled with on-chip USB port detection. • 400 mA linear battery charger • Linear charger for lithium-ion/lithium-polymer batteries • Adjustable charge current from 20 mA to 400 mA • Selectable termination voltage of 4.1 V or 4.2 V • Automatic trickle, constant current, and constant voltage charging • Battery thermal protection • Discharge current limitation • JEITA compliant • Li-ion/Li-polymer USB battery charger with a high efficiency buck regulator • 800 nA - Typical quiescent current • 460 nA - Shipping mode quiescent current • Thermal protection • Input regulator • USB compatible current limit of 100 mA and 500 mA • 4.1 V to 6.7 V input voltage range for normal operation • 20 V overvoltage protection • Reverse current protection • 3.0 V to 5.5 V system voltage output • USB port detection supporting the following types: • SDP • CDP/DCP • 1.8 V to 3.0 V, 150 mA step-down buck regulator • Step-down buck regulator with up to 92% efficiency • Automatic transition between hysteretic and pulse width modulation (PWM) modes • Forced PWM mode for clean power operation • Pin-selectable output voltage (1.8 V, 2.1 V, 2.7 V, 3.0 V) • Soft start-up • LED drivers for charger state indication • 5 mA low side LED driver for charging indication • 5 mA low side LED driver for error indication • 2.3 V to 4.35 V battery operating input range • 2.1x2.1 mm WLCSP package • Suitable for two layer PCB design #CommonPartsLibrary #IntegratedCircuit #NordicSemiconductor #nPM1100 #PMIC #BatteryCharger #PowerManagement #LiIon #LiPolymer #BuckConverter #Wearables #IoT #WirelessSensor #LowPowerDesign #USBCharging #EmbeddedSystems #nRF52 #nRF53 #PortableElectronics

LED Driver IC 1 Output DC DC Controller SEPIC, Step-Down (Buck), Step-Up (Boost) Analog, PWM Dimming 8-SO-EP # AL8866QSP-13 Engineering Specifications **General Description** The AL8866QSP-13 is an automotive-qualified, multi-topology DC-switching LED controller manufactured by Diodes Incorporated. It is designed to control an external power MOSFET for high-power automotive LED lighting systems. The device supports buck, boost, buck-boost and single-ended primary-inductance converter configurations. Its wide input-voltage range makes it suitable for automotive power systems and various high-voltage LED applications. The controller uses fixed-frequency peak current-mode regulation with spread-spectrum frequency modulation to reduce electromagnetic interference. It supports both analog and pulse-width-modulation dimming through the DIM input. An integrated programmable soft-start function gradually increases the inductor and switching currents during startup to reduce output-voltage and current stress. The open-drain fault output provides system-level fault reporting for abnormal operating conditions. **Engineering Specifications** **Manufacturer:** Diodes Incorporated **Manufacturer Part Number:** AL8866QSP-13 **Component Type:** Automotive LED driver controller **Converter Topologies:** Buck, boost, buck-boost and SEPIC **Control Architecture:** Fixed-frequency peak current-mode control **External Switching Device:** External power MOSFET **Minimum Input Voltage:** Four point seven volts **Maximum Input Voltage:** Eighty-five volts **Maximum Output Voltage:** Eighty-five volts **Switching Frequency:** Four hundred kilohertz **Frequency Modulation:** Spread-spectrum modulation for reduced electromagnetic interference **LED Current Control:** External current-sense resistor and external MOSFET configuration **Feedback Voltage:** Two hundred millivolts **Typical Quiescent Current:** One point eight milliamperes **Typical Efficiency:** Up to approximately ninety-three percent, depending on the application circuit and external components **Dimming Methods:** Analog dimming and pulse-width-modulation dimming **Analog Dimming Range:** One percent to one hundred percent **Analog Dimming Dynamic Range:** Greater than one hundred to one **Pulse-Width-Modulation Dimming Ratio:** One hundred to one at a two-hundred-hertz dimming frequency **Pulse-Width-Modulation Frequency Range:** Approximately one hundred hertz to one kilohertz **Full-Brightness Current Accuracy:** Approximately plus or minus three percent **Low-Level Dimming Current Accuracy:** Approximately plus or minus twelve percent at twenty-percent dimming **Soft-Start Function:** Externally programmable **Fault Output:** Active-low open-drain fault indicator **Protection Features:** Output overvoltage protection, LED open-circuit protection, output undervoltage protection, LED short-circuit protection, cycle-by-cycle overcurrent limitation, current-sense resistor short-circuit protection, inductor and diode short-circuit detection, diode open-circuit protection and thermal shutdown **Automotive Qualification:** AEC-Q100 Grade One qualified **Automotive Documentation:** PPAP capable **Manufacturing Standard:** Manufactured in IATF-certified automotive facilities **Operating Temperature Range:** Minus forty degrees Celsius to positive one hundred twenty-five degrees Celsius **Package Type:** Thermally enhanced SO-8 exposed-pad package **Pin Count:** Eight leads with exposed thermal ground pad **Mounting Style:** Surface mount **Packing Method:** Thirteen-inch tape and reel **Standard Packing Quantity:** Two thousand five hundred components per reel **Moisture Sensitivity:** Level One **Terminal Finish:** Matte-tin-plated leads **Environmental Compliance:** Lead-free, RoHS compliant, halogen-free and antimony-free **Typical Applications** Automotive high-beam and low-beam lighting Automotive daytime running lights Automotive fog lights Automotive turn-signal lights Automotive position lights Automotive brake and stop lights High-power exterior LED lighting Multi-topology automotive LED driver modules #AL8866QSP13 #AL8866Q #DiodesIncorporated #LEDDriver #AutomotiveLED #AutomotiveElectronics #BuckConverter #BoostConverter #BuckBoostConverter #SEPICConverter #PowerElectronics #LEDLighting #ElectronicComponents #EngineeringSpecifications

Ultra-Low IQ Synchronous Buck DC-DC Converter – 300 mA synchronous step-down (buck) switching regulator for high-efficiency industrial, automotive, battery-powered, and embedded power applications. Operates from a 3 V to 65 V input voltage, provides an adjustable output voltage from 1.0 V to 65 V, and delivers up to 300 mA output current. Features 6 µA typical quiescent current, programmable switching frequency from 200 kHz to 2.2 MHz, 100% duty-cycle operation, synchronous rectification, Power Good (PG) output, enable input, soft-start, cycle-by-cycle current limiting, hiccup short-circuit protection, thermal shutdown, and undervoltage lockout (UVLO). Specified for operation over a −40°C to +150°C junction temperature range and housed in a 9-pin VQFN-HR (2 × 2 mm) wettable-flank package. #TexasInstruments #LMR36503RFRPER #LMR36503 #BuckConverter #SynchronousBuck #DCDCConverter #SwitchingRegulator #PowerManagement #UltraLowIQ #300mA #VQFN9 #EmbeddedSystems

Non-Synchronous Buck DC-DC Converter – 3 A non-synchronous step-down (buck) switching regulator with an integrated 80 V, 3.5 A power MOSFET for industrial, telecom, and high-voltage power supply applications. Operates from a 12 V to 76 V input voltage, provides an adjustable output voltage from 1.0 V to 76 V, and features a programmable switching frequency from 50 kHz to 750 kHz. Includes current-mode control, soft-start, enable input, 0 µA standby current, precision reference (±1.5%), externally programmable undervoltage lockout (UVLO) with hysteresis, overcurrent protection (OCP), overvoltage protection (OVP), and thermal shutdown (TSD). Specified for operation over a −40°C to +85°C temperature range and housed in an 8-pin HTSOP-J exposed-pad package. #ROHM #BD9G341AEFJE2 #BD9G341AEFJ #BuckConverter #DCDCConverter #StepDownRegulator #SwitchingRegulator #PowerManagement #3A #80VMOSFET #IndustrialPower #HTSOPJ8 #EmbeddedSystems

Synchronous Buck DC-DC Converter – 2 A synchronous step-down (buck) switching regulator for high-efficiency power conversion in industrial, automotive, and embedded applications. Operates from a 4.5 V to 36 V input voltage, provides an adjustable output voltage from 0.6 V to 34.2 V, and switches at a 500 kHz fixed frequency. Features 40 µA typical quiescent current, 100% duty-cycle operation, synchronous rectification, cycle-by-cycle current limiting, hiccup short-circuit protection, thermal shutdown, undervoltage lockout (UVLO), power-good output, and enable input. Operates over a −40°C to +150°C junction temperature range and is housed in a 6-pin SOT-23-THIN (DDC) package. #TexasInstruments #LMR51420 #LMR51420XDDCR #BuckConverter #DCDCConverter #SynchronousBuck #SwitchingRegulator #PowerManagement #2A #SIMPLESWITCHER #SOT236 #EmbeddedSystems

Automotive 80 V, 2 A Synchronous Buck Converter IC – Automotive-grade synchronous step-down (buck) DC-DC converter optimized for automotive power supplies, industrial automation, battery-powered systems, distributed power, and embedded applications. Operates from a 4.2 V to 80 V input voltage and provides an adjustable output voltage from 1 V to 75 V with up to 2 A continuous output current. Features an integrated high-side and low-side MOSFET, 200 kHz to 2.2 MHz programmable switching frequency, 40 µA typical quiescent current, 98% maximum duty cycle, forced PWM/light-load efficiency modes, spread-spectrum EMI reduction, frequency synchronization, power-good output, fixed soft-start, and pre-biased startup. Includes comprehensive protection with cycle-by-cycle current limiting, hiccup-mode short-circuit protection, thermal shutdown, and undervoltage lockout (UVLO). Qualified to AEC-Q100 Grade 1, it operates over a −40°C to +125°C ambient (−40°C to +150°C junction) temperature range and is housed in an 8-pin SO PowerPAD (HSOIC) package. #TexasInstruments #LMR38020FSQDDARQ1 #LMR38020Q1 #BuckConverter #SynchronousBuck #DCDCConverter #PowerManagement #AutomotiveElectronics #AECQ100 #SIMPLESWITCHER #HSOIC8 #EmbeddedSystems

Automotive 8 A Synchronous Buck Converter IC – High-efficiency synchronous step-down (buck) DC-DC converter optimized for automotive power supplies, industrial automation, networking equipment, point-of-load regulation, and embedded power applications. Operates from a 4.5 V to 28 V input voltage and provides an adjustable output voltage from 0.6 V to 13 V with up to 8 A continuous output current. Features integrated high-side (20.4 mΩ) and low-side (9.5 mΩ) MOSFETs, D-CAP3™ control architecture for fast transient response, 45 µA typical quiescent current, selectable switching frequencies of 500 kHz, 800 kHz, or 1.2 MHz, pre-biased startup, power-good (PG) output, soft-start, frequency synchronization, and light-load Eco-mode™ operation for improved efficiency. Includes comprehensive protection with cycle-by-cycle current limiting, undervoltage lockout (UVLO), overvoltage protection (OVP), thermal shutdown, and hiccup-mode short-circuit protection. Specified for operation over a −40°C to +150°C junction temperature and housed in a compact 10-pin VQFN-HR (3 × 3 mm) package. #TexasInstruments #TPS56837RPAR #TPS56837 #BuckConverter #SynchronousBuck #DCDCConverter #PowerManagement #PointOfLoad #IndustrialElectronics #AutomotiveElectronics #VQFN10 #EmbeddedSystems

Non-Isolated PoL Module DC DC Converter 1 Output 0.6 ~ 5.5V 12A 3V - 16V Input #TexasInstruments #TPSM8A28RDGR #PowerModule #BuckConverter #DCDCConverter #VoltageRegulator #SynchronousBuck #8A #1MHz #QFN #PowerManagement #PCBComponents

Buck Switching Regulator IC Positive Adjustable 0.6V 1 Output 3A 14-VFQFN Buck step-down switching regulator that converts a 4V to 19V input supply to an adjustable output voltage from 0.6V, delivering up to 3A continuous output current. It uses Constant-On-Time (COT) control with programmable switching frequency, 40µA quiescent current, a Power Good indicator, programmable soft-start, selectable PWM/PFM operation, and integrates thermal shutdown and short-circuit protection in a 2mm × 3mm QFN-14 package. #DCDCConverter #BuckConverter #StepDownConverter #SwitchingRegulator #PowerManagementIC #MonolithicPowerSystems #QFN14

Buck Switching Regulator IC Positive Adjustable (Fixed) 0.8V (3.3V, 5V) 1 Output 4.5A 20-WFQFN Exposed Pad The LM656x5-Q1 are a family of automotive buck converters designed for high efficiency, high-power density, and ultra-low electromagnetic interference (EMI). The converters operate over a wide input voltage range of 3V to 65V (70V transient < 100ms), reducing the need for external input surge protection. The LM656x5-Q1 comes with pin selectable fixed output voltages of 3.3V and 5V or in adjustable configuration. The low EMI operation is enabled with minimized loop inductance and optimized switch node slew rate. A pin-selectable ±5% or ±10% dual-random spread spectrum (DRSS) significantly reduces peak emissions through a combination of triangular and pseudo-random modulation while keeping output voltage ripple very low. The current-mode control architecture with a 30ns typical minimum on-time allows high conversion ratios at high frequencies coupled with a fast transient response and excellent load and line regulation. Features • AEC-Q100 qualified for automotive applications: – Temperature grade 1: –40°C to +125°C, TA • Wide input voltage range: 3V to 65V (70V transient < 100ms) – Meets LV148 / ISO21780 requirements • Designed for low EMI requirements – Facilitates CISPR 25 class 5 compliance – Mode pin configurable ±5% or ±10% dualrandom spread spectrum reducing peak emissions – Enhanced HotRod™ QFN package with symmetrical pinout – Switching frequency from 300kHz to 2.2MHz – Pin-configurable AUTO or FPWM operation – Internal compensation, current limit, and TSD • Low minimum on time: 40ns (maximum) – Enables 36VIN to 3.3VOUT conversion at 2.2MHz • High-efficiency power conversion at all loads – > 94% peak efficiency at 24VIN, 5VOUT, 400kHz – 2.5µA switching input current at no load • High power density – 3.6mm × 2.6mm, wettable flank, 20-pin package – Pin compatible with 36V LM654x0-Q1 – ϴJA = 24.0°C/W (LM65645-Q1EVM) • Create a custom design using the LM656x5-Q1 with the WEBENCH® Power Designer 2 Applications • Advanced driver assistance systems (ADAS) • Automotive infotainment and cluster • Hybrid, electric, and powertrain systems #AutomotiveElectronics #BuckConverter #DCDCConverter #PowerManagement #VoltageRegulator #SynchronousBuck #LowEMI #AECQ100 #TexasInstruments #EmbeddedSystems