Voltage supervisor, designed to monitor the supply voltage and generate a reset signal when the monitored voltage falls below the specified threshold. The TLV840MADL29DBVR features a 2.9 V fixed threshold, manual reset (MR) input, active-low reset output, and is housed in a 5-pin SOT-23 (DBV) package, making it suitable for supply-voltage monitoring and reset generation in microprocessor and digital systems. #TexasInstruments #TLV840MADL29DBVR #VoltageSupervisor #ResetSupervisor #PowerMonitoring #VoltageMonitor #ActiveLowReset #ManualReset #SOT23 #DBV #PCB #Electronics #ComponentLibrary

ADC, Audio 8k ~ 192k I2S, TDM 20-WQFN (3x3) Analog-to-Digital Converter (ADC) IC that converts analog audio signals into digital data using a 24-bit delta-sigma architecture. The PCM1820IRTER supports stereo audio input, sampling rates up to 192 kHz, and digital audio output interfaces including I²S and TDM. It operates from a 3.3 V analog supply and is available in a 16-pin WQFN package. #AudioADC #DeltaSigmaADC #PCM1820IRTER #TexasInstruments #AudioInterface #ICComponent

Adjustable Low-Dropout (LDO) Linear Voltage Regulator – Positive adjustable LDO voltage regulator designed for power supplies, industrial control systems, embedded electronics, consumer devices, communication equipment, and analog circuits. Delivers up to 800 mA output current with an adjustable output voltage range of 1.25 V to 13.8 V using an external resistor divider. Operates from an input voltage up to 15 V with a maximum dropout voltage of 1.2 V at 800 mA, making it suitable for low-dropout linear regulation. Features 1% output voltage accuracy, 75 dB PSRR (120 Hz), 5 mA typical quiescent current, current limiting, and thermal shutdown protection for reliable operation. Designed for surface-mount applications in a TO-252-3 (DPAK) package and operates over a 0°C to +125°C temperature range. #TexasInstruments #LM1117DTADJNOPB #LM1117 #LDO #LinearRegulator #VoltageRegulator #AdjustableRegulator #PowerManagement #DPAK #EmbeddedSystems

Analog to Digital Converters - ADC Single-channel, 9-bit, 1.3-GSPS analog-to-digital converter (ADC) with JESD204C interface 144-FCBGA -40 to 85 ADC09xJ1300 is a family of quad, dual and single channel, 9-bit, 1.3GSPS analog-to-digital converters (ADC). Low power consumption, high sampling rate and 9-bit resolution makes the ADC09xJ1300 ideally suited for suited for a variety of multi-channel communications and test systems. Full-power input bandwidth (-3dB) of 6GHz enables direct RF sampling of L-band and S-band. A number of clocking features are included to relax system hardware requirements, such as an internal phase-locked loop (PLL) with integrated voltagecontrolled oscillator (VCO) to generate the sampling clock. Four clock outputs are provided to clock the logic and SerDes of the FPGA or ASIC. A timestamp input and output is provided for pulsed systems. JESD204C serialized interface decreases system size by reducing the amount of printed circuit board (PCB) routing. Interface modes support from 2 to 8 lanes (dual and quad channel devices) or 1 to 4 lanes (for the single channel device), with SerDes baud-rates up to 17.16Gbps, to allow the optimal configuration for each application. Features • ADC Core: – Resolution: 9 Bit – Maximum sampling rate: 1.3GSPS – Non-interleaved architecture – Internal dither reduces high-order harmonics • Performance specifications (–1dBFS): – SNR (100 MHz): 53.5dBFS – ENOB (100 MHz): 8.5 Bits – SFDR (100 MHz): 64dBc – Noise floor (–20dBFS): –143dBFS • Full-scale input voltage: 80 mVPP-DIFF • Full-power input bandwidth: 6GHz • JESD204C Serial data interface: – Support for 2 to 8 (Quad/Dual channel) or 1 to 4 (Single channel) total SerDes lanes – Maximum baud-rate: 17.16Gbps – 64B/66B and 8B/10B encoding modes – Subclass-1 support for deterministic latency – Compatible with JESD204B receivers • Optional internal sampling clock generation – Internal PLL and VCO (7.2–8.2GHz) • SYSREF Windowing eases synchronization • Four clock outputs simplify system clocking – Reference clocks for FPGA or adjacent ADC – Reference clock for SerDes transceivers • Timestamp input and output for pulsed systems • Power consumption (1GSPS): – Quad Channel: 450mW / channel – Dual channel: 625mW / channel – Single channel: 940mW • Power supplies: 1.1V, 1.9V #CommonPartsLibrary #IntegratedCircuit #ADC #HighSpeedADC #RFADC #JESD204C #13GSPS #9bitADC #DirectRFSampling #TexasInstruments #MixedSignal #DataAcquisition #JESD204

16-bit, 500-kSPS, eight-channel, single-supply SAR ADC with ±12-V differential inputs The ADS8684W and ADS8688W are 4-channel and 8-channel, integrated data acquisition systems based on a 16-bit successive approximation (SAR) analogto-digital converter (ADC), operating at a throughput of 500kSPS. The devices feature integrated analog front-end circuitry for each input channel with overvoltage protection up to ±20V, a 4-channel or 8-channel multiplexer with automatic and manual scanning modes, and an on-chip, 4.096V reference with low temperature drift. Operating on a single 5V analog supply, each input channel on the devices can independently support bipolar input ranges of ±12.288V, ±6.144V, and ±3.072V and unipolar input ranges of 12.288V to 0V and 6.144V to 0V. The ADS8684W and ADS8688W offer a simple SPIcompatible serial interface to the digital host and also support daisy-chaining of multiple devices. The digital supply operates from 1.65V to 5.25V, enabling direct interface to a wide range of host controllers Features • 16-Bit ADCs with Integrated Analog Front-End • 4-, 8-Channel MUX with Auto and Manual Scan • Channel-Independent Programmable Inputs: – ±12.288V, ±6.144V, and ±3.072V – 12.288V to 0V and 6.144V to 0V • 5V Analog Supply: 1.65V to 5V I/O Supply • Constant Resistive Input Impedance: 1.2MΩ • Input Overvoltage Protection: Up to ±20V • On-Chip, 4.096V Reference with Low Drift • Excellent Performance: – 500kSPS Aggregate Throughput – DNL: ±0.6LSB; INL: ±0.8LSB – Low Drift for Gain Error and Offset – SNR: 91.5dB; THD: –102dB – Low Power: 65mW • AUX Input → Direct Connection to ADC Inputs • ALARM → High and Low Thresholds per Channel • SPI™-Compatible Interface with Daisy-Chain • Industrial Temperature Range: –40°C to 125°C #commonpartslibrary #ADS8688W #TexasInstruments #ADC #SARADC #DataAcquisition #IndustrialAutomation #SPI #PrecisionADC #AnalogFrontEnd #EmbeddedSystems #MeasurementSystems

This LM2679SX-ADJ reference design is a step-down voltage regulator providing a stable 5V output from a higher input voltage. Ideal for applications needing a regulated 5V supply. #referenceDesign #project #stepDown #voltageRegulator #5V #LM2679SX-ADJ #LM2679-ADJ #LM2679 #Module #subLayout #reusable #module #powermanagement #texas-instruments #sublayout

The TMS320F280049CPZQR is a 32-bit real-time microcontroller from Texas Instruments' C2000 Piccolo family, purpose-built for high-performance digital power control, motor control, and other real-time embedded control applications. The device is centered around TI's C28x digital signal processing core, a fixed- and floating-point architecture specifically optimized for the kind of fast, deterministic mathematical computation required in closed-loop control systems such as motor drives, digital power supplies, solar inverters, and electric vehicle subsystems. This particular part number represents the "C" variant within the TMS320F28004x family, which grants access to an integrated Configurable Logic Block, a flexible programmable logic resource that allows engineers to implement custom digital logic functions directly on-chip, such as specialized PWM waveform shaping, custom protocol interfaces, or glue logic that would otherwise require an external FPGA or discrete logic devices. This variant also provides access to a secure ROM library containing TI's InstaSPIN-FOC technology, a field-oriented motor control solution that significantly simplifies the development of sensorless motor control algorithms by handling much of the underlying control theory and tuning complexity in pre-validated, secure firmware. Beyond its core processing capabilities, the device integrates an extensive set of control-oriented peripherals that are characteristic of the C2000 platform, including high-resolution pulse-width modulation outputs, enhanced capture modules, and a multi-channel sigma-delta filter module that enables isolated current and voltage sensing across an isolation barrier without requiring a separate digital isolator and decoder chip. A dedicated Control Law Accelerator runs in parallel with the main processing core, offloading time-critical control loop calculations so that the main core remains free to handle communication, supervisory logic, and other system-level tasks, which is particularly valuable in systems running multiple simultaneous control loops. Connectivity on the device is supported through a broad set of industry-standard communication interfaces, allowing it to interface with a wide range of external sensors, communication networks, and host systems without requiring additional bridge components. The device also supports TI's Fast Serial Interface, a high-speed, robust communication protocol intended to simplify board-to-board and module-to-module communication in multi-controller systems, an increasingly common need in distributed power and motor control architectures. This part is qualified to automotive electronics reliability standards, making it suitable for deployment in vehicle power electronics, traction inverters, onboard chargers, and other automotive systems where component robustness, extended temperature operation, and rigorous quality screening are required. The device also supports TI's functional safety documentation framework, providing the architectural transparency and failure mode analysis resources needed by system designers building safety-critical control systems around the device. It is housed in a surface-mount package suited to dense power electronics board layouts and is supplied in tape-and-reel packaging for automated assembly. Spec Sheet Identification Part Number: TMS320F280049CPZQR Device Family: C2000 Piccolo, TMS320F28004x Manufacturer: Texas Instruments Variant: "C" type — with Configurable Logic Block and secure ROM/InstaSPIN-FOC access Functional Classification Device Type: 32-bit real-time microcontroller Core Architecture: C28x digital signal processing core Math Acceleration: Floating-Point Unit and Trigonometric Math Unit for control-loop computation Parallel Control Processing: Integrated Control Law Accelerator Programmable Logic: Configurable Logic Block (CLB) for custom digital logic functions Motor Control Library: Secure ROM with InstaSPIN-FOC sensorless field-oriented control Memory Program Memory Type: Embedded flash memory Memory Architecture: Supports field reprogramming for firmware updates and calibration data storage Control & Analog Peripherals PWM Capability: Frequency-independent, high-resolution PWM outputs Capture Module: Enhanced capture (eCAP) peripheral Isolated Sensing: Multi-channel sigma-delta filter module (SDFM) for isolated current/voltage sensing Analog Integration: Integrated high-speed analog-to-digital converters and internal digital-to-analog converters Programmable Gain: Integrated programmable gain amplifiers Communication Interfaces Standard Interfaces: SPI, SCI, I2C, LIN, and CAN connectivity Power Management Bus: Fully compliant PMBus support High-Speed Module Interface: Fast Serial Interface (FSI) for board-to-board and module-to-module communication Target Applications Application Domains: Industrial motor drives, solar inverters, digital power supplies, electric vehicle and transportation systems, sensing and signal processing Environmental & Qualification Automotive Qualification: AEC-Q100 qualified Functional Safety Support: Documentation and architecture support for functional safety-compliant system design Lifecycle Status: Active production Package Package Type: Surface-mount quad flat package style (LQFP) Mounting: Surface mount technology (SMT) Packaging Format Supply Format: Tape-and-reel, per part suffix designation #TMS320F280049 #C2000 #Piccolo #TexasInstruments #DigitalSignalController #RealTimeMCU #MotorControl #DigitalPowerControl #InstaSPINFOC #FieldOrientedControl #ConfigurableLogicBlock #AECQ100 #AutomotiveMCU #PowerElectronics #EmbeddedSystems #LQFP #SurfaceMount #SemiconductorIC #EngineeringSpec #ComponentLibrary #CommonPartsLibrary

This SN65HVD230DR-based reference design is a CAN bus transceiver circuit that facilitates robust data communication across the CAN network. The design incorporates a variety of capacitors and resistors to maintain signal quality, and it employs a NUP2105L for voltage protection. This circuit is ideally suited for applications that need reliable data communication in automotive or industrial settings. #referenceDesign #Module #CANbus #interface #transceiverCircuit #SN65HVD230 #SN65HVD230DR #reusable #module #canbus #texas-instruments #sublayout

This project is a reference design based on the BQ24075RGTT, a single cell Li-Ion battery charger. It manages the power between an external power source (VIN), a Li-Ion battery (BAT), and a system power rail (SYS). Key features include power-path management, battery thermistor monitoring, and charge status indication. #Module #BQ24075 #ReferenceDesign #charger #BatteryManagement #reusable #module #bms #texas-instruments #sublayout

This LM2678SD-5.0 reference design is a step-down voltage regulator providing a stable 5V output from a higher input voltage. It uses capacitors, an inductor, and a diode for filtering and protection, with an ON/OFF terminal for control. Ideal for applications needing a regulated 5V supply. #referenceDesign #stepDown #voltageRegulator #5V #Module #subLayout #reusable #module #powermanagement #texas-instruments #sublayout

This project is a reference design based on the BQ25890, a single cell Li-Ion battery charger. It manages the power between an external power source (VIN), a Li-Ion battery (BAT), and a system power rail (SYS). Key features include power-path management, battery thermistor monitoring, and charge status indication. #Module #BQ25890 #ReferenceDesign #charger #BatteryManagement #reusable #module #bms #texas-instruments #sublayout

This TCAN1042HDR-based reference design is a CAN bus transceiver circuit that facilitates robust data communication across the CAN network. The design incorporates a variety of capacitors and resistors to maintain signal quality, and it employs a NUP2105L for voltage protection. This circuit is ideally suited for applications that need reliable data communication in automotive or industrial settings. #referenceDesign #module #CANbus #interface #transceiverCircuit #TCAN1042 #TCAN1042HDR #reusable #module #canbus #texas-instruments #sublayout

This project is a reference design based on the BQ24230 , a single cell Li-Ion battery charger. It manages the power between an external power source (VIN), a Li-Ion battery (BAT), and a system power rail (SYS). Key features include power-path management, battery thermistor monitoring, and charge status indication. #Module #BQ24230 #ReferenceDesign #charger #BatteryManagement #reusable #module #bms #texas-instruments #sublayout #polygon

This is a module of the LM27313 boost converter with an input voltage of 5V and output of 12V 0.25A #reusable #module #powermanagement #texas-instruments #sublayout

This TPS5420D reference design is a step-down voltage regulator providing a stable 5V output from a higher input voltage. It uses capacitors, an inductor, and a diode for filtering and protection, with an EN terminal for control. Ideal for applications needing a regulated 5V supply. #referenceDesign #stepDown #voltageRegulator #5V #TPS5420 #Module #subLayout #reusable #module #powermanagement #texas-instruments #sublayout #polygon

This ADM3054BRWZ-RL7-based reference design is a CAN bus transceiver circuit, providing reliable data communication over the CAN network. The design features a range of capacitors and resistors to ensure signal integrity, and a NUP2105L for voltage protection. It's ideal for applications requiring reliable data communication in an automotive or industrial environment. #referenceDesign #module #CANbus #interface #transceiverCircuit #ADM3054 #ADM3054BRWZ-RL7 #reusable #module #canbus #texas-instruments #sublayout