High-Speed Logic Output Optocoupler – Single-channel high-speed optocoupler designed for digital signal isolation, industrial automation, PLCs, motor drives, switching power supplies, data communication, microcontroller interfaces, and embedded control systems. Features an open-collector TTL-compatible output with a 15 MBd data rate, 5 kVrms isolation voltage, and 10 kV/µs minimum common-mode transient immunity (CMTI) for reliable operation in noisy electrical environments. Provides 75 ns maximum propagation delay, 22 ns typical rise time, 6.9 ns typical fall time, and supports up to 50 mA output current. The input consists of a GaAs infrared LED with a 1.38 V typical forward voltage and 20 mA maximum forward current. Operates from a 4.5 V to 5.5 V output-side supply, over a −40°C to +85°C temperature range, and is housed in a compact 8-pin SOIC (SMD) package for space-efficient PCB designs. #LiteOn #6N137STA1 #6N137 #Optocoupler #LogicOptocoupler #DigitalIsolation #HighSpeedIsolation #IndustrialAutomation #MotorDrive #PLC #EmbeddedSystems

Dual Non-Inverting Open-Drain Buffer IC – Dual non-inverting buffer with open-drain outputs for logic level translation, bus interfacing, signal buffering, wired-AND logic, and embedded digital systems. Operates from a 1.65 V to 5.5 V supply and features two independent 1-bit buffer channels capable of sinking up to 32 mA per output. The open-drain outputs allow direct interfacing with multiple voltage domains using external pull-up resistors, making the device suitable for I²C buses, interrupt lines, LED driving, and mixed-voltage logic applications. Features high-speed CMOS operation, low static power consumption, 5.5 V input tolerance, and is specified for operation over a −40°C to +85°C ambient temperature range. Housed in a 6-pin SC-88 (SC-70-6 / SOT-363) surface-mount package. #onsemi #NC7WZ07P6X #LogicBuffer #OpenDrain #NonInvertingBuffer #LogicIC #LevelShifter #I2C #SignalBuffer #WiredAND #SC88 #EmbeddedSystems

Power Management IC (PMIC) integrating battery charging, power regulation, fuel gauging, and system management for single-cell Li-ion, Li-poly, and LiFePO₄ batteries. It features a 4–100 mA linear battery charger, two 200 mA buck regulators, two configurable 50 mA LDOs or 100 mA load switches, USB-C compatible input (4.0–5.5 V) with 22 V overvoltage protection, and an I²C-compatible TWI interface with watchdog, hard reset, power-loss warning, GPIOs, and LED drivers. #PMIC #PowerManagementIC #BatteryCharger #FuelGauge #BuckRegulator #LDO #USBTypeC #I2C #TWI #NordicSemiconductor #LiIon #LiPo #LiFePO4

IEEE 802.3bt Type 4 Power over Ethernet (PoE) Powered Device Module – High-power isolated PoE Powered Device (PD) module for IP cameras, wireless access points, LED lighting, digital signage, industrial automation, access control, IoT gateways, and embedded networking applications. Fully compliant with IEEE 802.3bt Type 4, it accepts a 36 V to 57 V PoE input and delivers up to 85 W output power with selectable 12 V or 24 V regulated outputs and an adjustable output voltage. Features a high-efficiency isolated DC-DC converter (up to 89%), 1.5 kV input-to-output isolation, integrated PD detection and classification, low output ripple and noise, and comprehensive overload, thermal, and short-circuit protection. Designed to minimize external components for simplified PoE implementation, it is housed in a compact through-hole DIL module (70 × 35 × 17 mm) and operates over a −40°C to +85°C temperature range. #Silvertel #AG5800 #PoEPoweredDevice #IEEE8023bt #PowerOverEthernet #PDModule #IsolatedDCDC #IndustrialEthernet #IPCamera #LEDLighting #EmbeddedPower #EmbeddedSystems

This is a schematic of an IR (infrared) remote control system. It's built around a Microchip ATTINY2313 microcontroller (U1) and boasts five push-button switches, an indicator RED LED and an electret buzzer for user interaction. An ISP header provides programming capabilities. The project is battery-powered and implements boost converter TPS613222AD (IC1) for stable power supply. #project #Template #projectTemplate #lock #keypad #attiny2313 #TPS613222A #ISP #buzzer #reusable #module #simple-embedded #microchip #arduino #sublayout

225k ~ 1.4M Modem PSK 32-QFN (5x5) The DCB1M is a device for multiplex communication over noisy power lines, at speed up to 1.4Mbit/s. The DCB1M is based on the DC-BUS™ technology for network communication between modules sharing a common DC or AC powerline. The device avoids complex cabling, saves weight, and simplifies installation. The DCB1M supports UART, SPI, DMX512, RDM, and I 2C protocols, enabling the user to meet this application protocol. Sleep mode allows low power consumption when the device is not used. A QFN32 5x5 mm package provides a small PCB footprint The DCB1M is beneficial for many applications ranging from LED, Aerospace, Automotive, Industrial, and even Toys. Features • Noise robust UART, SPI, DMX512, RDM, and I2C transceiver over DC powerline. • Bitrate up to 1.4Mbit/s over the powerline. • Multiple networks may operate over a single powerline. • 251 selectable carrier frequencies (5MHz to 30MHz). • Built-in CSMA/CA (powerline arbitration) mechanism. • Operates as Multi-master Transceiver in a multiplex network. • Channel interference detection. • Communicates over a wide range of DC voltages. • Power management (Sleep modes) for low power consumption.

TM1814 is four channels LED constant current adjustable driver IC with function of internal control synchronizing, which can achieve a wide range of display as MCU inputs one group of data set by constant current and PWM to TM1814. When input signal is disconnected, it can realize synchronized fixation of colorful pattern change and prevent in-operation of subsequent cascade chip caused by chip damage. Internal chip is integrated with MCU solidification program and single wire digital interface, data flip-latch, LED constant current driver, circuit, etc. Internal VDD pin is integrated with 5V regulator with less peripheral devices, which applies to guardrail tube, point source and LED decorative products. This product has excellent performance and reliable quality. Features  Adopt power CMOS technology  Withstand voltage of OUT output port is 32V  5 V voltage-regulator tube is built into VDD, and the voltage supports 6-24 V after cascading the resistor  Constant current can achieve level 64 adjustment (6.5 mA-38mA)  PWM brightness controls circuit, and 256 brightness is adjustable  Accurate current output value Maximum error (between channels): ±3% Maximum error (between chips): ±5%  Single line serial concatenated port  Oscillation mode: build in RC vibration and conduct clock synchronization according to signals on data line. After receiving the data from this unit, it can reproduce follow-up data and send it to lower level through data output end, and signals will not be distorted and reduced along with cascade  Build in power on reset circuit, and after powering on reset, all registers are initialized to zero  External control mode data transmission rate is 800 KHZ  Internal control mode data transmission rate is 500 KHZ  Internal control mode chip sends 2048 points of data  Encapsulation mode: SOP8 #CommonPartsLibrary #IntegratedCircuit

This project is a of ESP32-S3-MINI-1. It features USB-C for power and data transfer, onboard voltage regulation, and multiple peripheral connections. It also includes user RGB LED #referenceDesign #Module #ESP32 #ESP32S2 #RF #WIFI #MCU #reusable #module #simple-embedded #espressif #sublayout

The Hi5000Q is a high-precision, flicker-free LED constant-current driver IC designed for buck, boost, and buck-boost LED lighting applications. It supports external MOSFET operation, making it suitable for high-power LED systems such as automotive lighting, medical lighting, photography lamps, desk lamps, and educational lighting. Key Features Wide input voltage range: 6.5V to 75V Supports buck, boost, and buck-boost topologies External MOSFET architecture for high current capability Up to 10A continuous output current High efficiency operation exceeding 95% Flicker-free LED dimming control Supports: 100:1 PWM-to-analog dimming 10,000:1 hybrid dimming 10:1 analog dimming Fixed switching frequency of 130kHz Very low standby power consumption Excellent load regulation accuracy (less than ±0.5%) Built-in soft-start function Undervoltage protection (UVLO) Output overvoltage protection (OVP) Cycle-by-cycle current limiting protection Available in QFN16 4x4mm package

LED Drivers IMX101U-TL HSOP-28_L18.0-W7.5-P0.80-LS10.1-BL LCSC Part Number: C1870396 JLCPCB Part Class: undefined Manufactured by Power Integrations(帕沃英蒂格盛)

ESP32-S3-DEVKITC-1-N16R8V is an Espressif ESP32-S3-DevKitC-1 v1.1 development board based on the ESP32-S3-WROOM-2-N16R8V module. It provides dual-core ESP32-S3 processing, 2.4 GHz Wi-Fi, Bluetooth LE, 16 MB Octal SPI flash, 8 MB Octal SPI PSRAM, USB programming/debugging, native USB OTG/JTAG capability, onboard power regulation, and two 22-pin 2.54 mm header rows for prototyping. Note: on this WROOM-2/N16R8V variant, GPIO35, GPIO36, and GPIO37 are used internally for Octal SPI flash/PSRAM and are not available for external use; GPIO38 drives the onboard RGB LED on v1.1 boards.

LED Drivers IMX111J-TL QFN-28_L5.0-W5.0-P0.50-TL-EP3.5 LCSC Part Number: C1870397 JLCPCB Part Class: undefined Manufactured by Power Integrations(帕沃英蒂格盛)

DGUK411Q199DB2A1DP (POE+) is a single-port RJ45 Ethernet connector with integrated magnetics (MagJack) designed for 10/100/1000BASE-T Gigabit Ethernet applications. It supports Power over Ethernet Plus (PoE+) in compliance with IEEE 802.3at, allowing both data and power transmission through a single Ethernet cable. The connector features integrated isolation transformers, EMI suppression, LED indicators for link/activity status, and a shielded through-hole right-angle design, making it suitable for networking equipment, industrial Ethernet devices, IP cameras, wireless access points, and PoE-powered embedded systems. Key Features Single-port RJ45 connector with integrated magnetics (MagJack) Supports 10/100/1000BASE-T Gigabit Ethernet PoE+ (IEEE 802.3at) compatible for Power Sourcing Equipment (PSE) and Powered Device (PD) applications Integrated isolation transformers and common-mode noise filtering Shielded construction for improved EMI performance Right-angle, through-hole PCB mounting Built-in dual LED indicators for link and activity status High isolation voltage (2250 VDC) RoHS compliant Ideal for routers, switches, industrial controllers, IP cameras, IoT gateways, and other Gigabit Ethernet devices with PoE support #RJ45 #MagJack #EthernetConnector #GigabitEthernet #1000BASE_T #PoEPlus #IEEE8023at #IntegratedMagnetics #Networking #IndustrialEthernet #EmbeddedSystems #ThroughHole #ShieldedConnector #PCBDesign

The HOTCHIP HT4936S is a sophisticated mobile power management integrated circuit designed by Hotchip, optimized for portable power solutions that require efficient charging and power management capabilities. This advanced component integrates features for charging and discharging through a common port, automatic load detection for boost startup and shutdown, four-light battery level indication, and a low battery alert functionality. The HT4936S stands out for its ability to manage 1A input/output with minimal external components, leveraging synchronous rectification to enhance efficiency and reduce thermal footprint. Additionally, it supports a versatile charging protocol accommodating both 4.20V and 4.35V batteries, and is packaged in a compact SOP16 form factor, ensuring a low-cost, space-efficient solution for a wide range of mobile power applications including power banks, backup power supplies, and lithium battery chargers. It incorporates protection features against battery overcharge, over-discharge, and thermal overload, thereby ensuring reliable operation across a range of conditions. Furthermore, the HT4936S facilitates direct LED drive and includes an NTC thermistor input for temperature monitoring, making it an all-encompassing solution for power management in consumer electronics.

VU Meter Dot/Bar Display Driver IC – 10-step analog level display driver for audio VU meters, signal strength indicators, battery level monitors, power meters, and instrumentation displays. Features a logarithmic response matched to human hearing, driving 10 LEDs, LCDs, or vacuum fluorescent (VF) displays in either dot or bar mode. Operates from a single 3 V to 25 V supply, includes an adjustable 1.2 V to 12 V precision voltage reference, and provides programmable constant-current LED outputs (typically 2 mA to 30 mA) without requiring external current-limiting resistors. Supports 70 dB display range, expandable multi-device cascading for higher resolution, and offers fast analog response for real-time level indication. Specified for operation over a 0°C to +70°C temperature range and housed in an 18-pin PDIP package. This device is obsolete/Lifetime Buy and is not recommended for new designs. #TexasInstruments #LM3916N1NOPB #LM3916 #VUDriver #BarGraphDriver #DotBarDisplay #LEDDriver #AudioMeter #LevelIndicator #DisplayDriver #PDIP18 #EmbeddedSystems

2.4GHz -98dBm SMD,19.2x18mm RF Transceiver Modules and Modems RoHS The ESP32-WROOM-32UE-N16 is a 2.4 GHz wireless MCU module built around the ESP32 SoC. It combines a dual-core processor, integrated Wi-Fi (802.11 b/g/n) and Bluetooth 4.2 (Classic + BLE), along with rich peripherals. The “UE” variant specifically uses a U.FL / IPEX connector for an external antenna, making it ideal for applications that require better RF performance or flexible antenna placement (e.g., enclosed products or long-range communication). The “N16” indicates 16 MB external flash memory, suitable for large firmware, OTA updates, and data-heavy applications. Processing Dual-core Xtensa LX6 32-bit CPU Clock speed up to 240 MHz Memory 16 MB Flash (N16 variant) ~520 KB SRAM + 448 KB ROM Connectivity Wi-Fi: 802.11 b/g/n (up to 150 Mbps) Bluetooth: v4.2 (BR/EDR + BLE) Frequency: 2.4 GHz band Antenna External antenna via U.FL connector Better range and flexibility vs PCB antenna Interfaces / Peripherals GPIO (≈26 usable pins) UART, SPI, I2C, I2S, SDIO ADC, DAC PWM (LED & motor control) Capacitive touch sensing Security Hardware encryption: AES, SHA, RSA Secure boot & flash encryption support Power Operating voltage: 3.0V – 3.6V (typ. 3.3V) Multiple low-power modes for battery applications Environmental Operating temperature: -40°C to +85°C Physical Surface-mount module (~38 pins / 52 pads depending on reference) Compact and RF-shielded design Typical Applications Smart home devices (IoT) Industrial automation Wireless sensors and data loggers Wearables and consumer electronics Remote monitoring systems #Module #ESP32

WiFi 802.11a/b/g/n, Bluetooth v5.0 Transceiver Module 2.4GHz PCB Trace The ESP32-S3-WROOM-1-N8R2 is a compact, low-power Wi-Fi and Bluetooth® Low Energy (BLE) module developed by Espressif Systems. It is based on the ESP32-S3 system-on-chip (SoC), which integrates a dual-core Xtensa® LX7 processor optimized for high performance and edge AI processing. This module includes 8 MB of external SPI flash memory and 2 MB of PSRAM, enabling efficient handling of memory-intensive applications such as graphical interfaces, buffering, and embedded machine learning workloads. Designed for flexibility and scalability, the module integrates RF components, power management, and a wide range of peripherals into a surface-mount package suitable for IoT, industrial, and consumer electronics applications. Key Features Dual-core Xtensa® LX7 processor operating up to 240 MHz Integrated 2.4 GHz Wi-Fi (802.11 b/g/n) Bluetooth 5 Low Energy support Embedded 8 MB SPI flash memory Integrated 2 MB PSRAM AI acceleration through vector instruction support USB OTG (full-speed) capability Multiple low-power operating modes Built-in hardware security features Extensive peripheral interface support Functional Overview The module consists of several integrated subsystems, including a dual-core processing unit, memory subsystem (flash and PSRAM), RF subsystem for wireless communication, peripheral interface controllers, power management circuitry, and a hardware-based security engine. Electrical Characteristics Operating voltage range: 3.0 V to 3.6 V (typical 3.3 V) Operating temperature range: -40°C to +85°C RF operating frequency: 2.4 GHz Current consumption varies depending on operating mode, ranging from microamp levels in deep sleep to hundreds of milliamps during active transmission Processor and Memory The module features a dual-core Xtensa® LX7 CPU capable of running at frequencies up to 240 MHz. It includes approximately 512 KB of internal SRAM, supplemented by 8 MB of external flash memory and 2 MB of PSRAM for extended data storage and processing. Wireless Connectivity The ESP32-S3-WROOM-1-N8R2 supports Wi-Fi communication compliant with 802.11 b/g/n standards in the 2.4 GHz band. It also supports Bluetooth 5 Low Energy for short-range wireless communication. The module includes an integrated PCB antenna and supports RF output power up to approximately +20 dBm. Peripheral Interfaces The module provides a wide range of interfaces, including general-purpose input/output (GPIO) pins, SPI, I2C, UART, and I2S for audio applications. It also supports PWM for LED control, a 12-bit analog-to-digital converter (ADC), and USB OTG functionality. Pin functions are multiplexed to maximize flexibility. Power Management Power efficiency is achieved through multiple operating modes, including active mode, modem sleep, light sleep, and deep sleep. The module includes an RTC subsystem for low-power timekeeping and supports dynamic frequency scaling to optimize performance and energy consumption. Security Features The module incorporates several hardware-based security mechanisms, including secure boot, flash encryption, and digital signature verification. It also includes a hardware random number generator and cryptographic accelerators supporting AES, SHA, RSA, and ECC algorithms. Mechanical Characteristics The module is designed for surface-mount integration and measures approximately 18 mm by 25.5 mm. It includes an onboard PCB antenna and is suitable for compact embedded designs. Pin Configuration Overview GPIO pins are multiplexed to support various peripheral functions such as analog inputs, communication interfaces, and control signals. Dedicated pins are provided for power supply, module enable, and boot configuration. Typical Applications Internet of Things (IoT) devices Smart home systems Industrial automation and monitoring Edge AI and machine learning applications Wearable electronics Audio and multimedia systems USB-enabled embedded devices Compliance The module is designed to meet Wi-Fi and Bluetooth standards and is compliant with RoHS requirements. Certification such as FCC or CE may apply depending on the specific module variant and deployment. Ordering Information The ESP32-S3-WROOM-1-N8R2 variant includes 8 MB of flash memory and 2 MB of PSRAM. #commonpartslibrary #integratedcircuit #transceiver #wireless #rf

MOSFET N-CH 20V 3.6A SOT-23 The IRLML2502 is a small-signal N-channel enhancement mode power MOSFET designed for low-voltage, high-efficiency switching applications. It is commonly used as a load switch or power control transistor in compact electronic systems such as battery-powered devices, LED drivers, and DC-DC converters. It features a low on-resistance (RDS(on)), which allows it to switch higher currents with minimal power loss and heat generation. The device is optimized for logic-level gate drive, meaning it can be driven directly from microcontrollers (like 3.3 V or 5 V systems). It is packaged in a compact SOT-23 (Micro3) surface-mount package, making it suitable for space-constrained PCB designs. Key Features N-channel enhancement mode MOSFET Drain-source voltage (VDS) up to 20 V Continuous drain current up to ~4.2 A (at 25°C) Very low RDS(on) ≈ 45 mΩ @ VGS = 4.5 V Logic-level gate drive capability (works with 2.5–4.5 V signals) Fast switching performance Compact SOT-23 (Micro3) surface-mount package Low gate charge for efficient switching Suitable for battery-powered and low-voltage applications RoHS compliant, lead-free design #IRLML2502 #MOSFET #NChannelMOSFET #PowerElectronics #SOT23 #LogicLevelMOSFET #PowerSwitch #ElectronicComponents #EmbeddedSystems #PCBDesign

LED Driver IC 16 Output Linear PWM Dimming 25mA 28-TSSOP The PCA9685 is an I2C-bus controlled 16-channel LED controller optimized for Red/Green/Blue/Amber (RGBA) color backlighting applications. Each LED output has its own 12-bit resolution (4096 steps) fixed frequency individual PWM controller that operates at a programmable frequency from a typical of 24 Hz to 1526 Hz with a duty cycle that is adjustable from 0 % to 100 % to allow the LED to be set to a specific brightness value. All outputs are set to the same PWM frequency. Each LED output can be off or on (no PWM control), or set at its individual PWM controller value. The LED output driver is programmed to be either open-drain with a 25 mA current sink capability at 5 V or totem pole with a 25 mA sink, 10 mA source capability at 5 V. The PCA9685 operates with a supply voltage range of 2.3 V to 5.5 V and the inputs and outputs are 5.5 V tolerant. LEDs can be directly connected to the LED output (up to 25 mA, 5.5 V) or controlled with external drivers and a minimum amount of discrete components for larger current or higher voltage LEDs. The PCA9685 is in the new Fast-mode Plus (Fm+) family. Fm+ devices offer higher frequency (up to 1 MHz) and more densely populated bus operation (up to 4000 pF). Although the PCA9635 and PCA9685 have many similar features, the PCA9685 has some unique features that make it more suitable for applications such as LCD or LED backlighting and Ambilight: • The PCA9685 allows staggered LED output on and off times to minimize current surges. The on and off time delay is independently programmable for each of the 16 channels. This feature is not available in PCA9635. • The PCA9685 has 4096 steps (12-bit PWM) of individual LED brightness control. The PCA9635 has only 256 steps (8-bit PWM). • When multiple LED controllers are incorporated in a system, the PWM pulse widths between multiple devices may differ if PCA9635s are used. The PCA9685 has a programmable prescaler to adjust the PWM pulse widths of multiple devices. • The PCA9685 has an external clock input pin that will accept user-supplied clock (50 MHz max.) in place of the internal 25 MHz oscillator. This feature allows synchronization of multiple devices. The PCA9635 does not have external clock input feature. • Like the PCA9635, PCA9685 also has a built-in oscillator for the PWM control. However, the frequency used for PWM control in the PCA9685 is adjustable from about 24 Hz to 1526 Hz as compared to the typical 97.6 kHz frequency of the PCA9635. This allows the use of PCA9685 with external power supply controllers. All bits are set at the same frequency. • The Power-On Reset (POR) default state of LEDn output pins is LOW in the case of PCA9685. It is HIGH for PCA9635. #CommonPartsLibrary #IntegratedCircuit #PowerManagement

Infrared (IR) Emitter 940nm 1.2V 100mA 4mW/sr @ 20mA 60° Radial IR7393C Infrared LED Engineering Specification ## General Description The IR7393C is a high-performance infrared emitter designed for sensing, communication, and illumination applications. Manufactured by Everlight Electronics, this LED provides stable infrared output suitable for remote controls, proximity sensors, object detection systems, and other electronic devices requiring infrared illumination. Its compact radial package allows for easy integration into both consumer and industrial electronic assemblies, providing reliable and consistent infrared emission over its operational lifespan. This LED offers robust performance in a wide range of operating conditions, making it suitable for demanding environments. ## Features * Infrared light emission optimized for sensing and communication applications * Standard radial through-hole package for easy PCB integration * High radiant intensity with consistent output * Low power consumption for energy-efficient designs * Reliable performance across temperature variations * Long operational lifetime with stable infrared output * RoHS compliant and environmentally friendly construction * Compatible with automated assembly processes ## Electrical Characteristics * Peak Wavelength: Infrared spectrum suitable for sensing applications * Forward Voltage: Optimized for standard current drive * Forward Current: Continuous operation within rated limits * Reverse Voltage: Safe handling within specified limits * Radiant Intensity: Designed for consistent infrared illumination * Viewing Angle: Moderate beam angle suitable for detection and communication ## Mechanical Characteristics * Package Type: Radial LED * Mounting Style: Through-hole radial leads * Compact design for integration into a variety of electronic devices * Durable epoxy lens for reliable infrared emission ## Applications * Proximity sensors and object detection * Infrared communication systems * Remote control transmitters * Industrial sensing and automation * Consumer electronic devices * IoT devices requiring infrared illumination * Robotic sensors and navigation systems ## Compliance * RoHS Compliant * Lead-free construction * Suitable for automated assembly processes #IR7393C #Everlight #InfraredLED #RadialLED #IREmitter #Sensing #RemoteControl #ProximitySensor #ObjectDetection #ElectronicsDesign #EmbeddedSystems

-40℃~+85℃ 120° 3.2V 527nm 5mA 685mcd 80mW Discrete Diode Emerald Green Water Clear 0603 LED Indication - Discrete ROHS The BZ-C0603-G3-F1 is a surface-mount (SMD) 0603 chip LED designed to emit emerald green light (~527 nm). It is optimized for low-power indicator applications and backlighting, offering high brightness in a very small package size suitable for modern compact PCB designs. ⭐ Key Features 📦 Package: 0603 (1.6 × 0.8 mm SMT LED) 💡 Color: Emerald Green / Green LED (~527 nm wavelength) 🔆 Luminous intensity: up to ~685 mcd (typical high-brightness grade) ⚡ Forward voltage: ~2.6 V to 3.2 V (typical at 5 mA) 🔌 Forward current: ~5 mA (typical operating current) 📐 Viewing angle: ~120° wide viewing angle 🔥 Power rating: ~80 mW maximum 🌡️ Operating temperature: −40°C to +85°C 🧲 ESD protection: up to ~2000 V (HBM) ♻️ RoHS compliant, suitable for automated SMT assembly #CommonPartsLibrary #LED

LED Drivers RCD-24-0.70 PWRM-TH_RCD-24-0.70 LCSC Part Number: C1519167 JLCPCB Part Class: Extended Part Manufactured by Recom Power