This project is a motherboard for the ESP32-CAM module, which enables easy and flexible WiFi camera applications. The motherboard provides power supply, programming interface, and GPIO expansion for the ESP32-CAM. It also supports external sensors for more functionality. #motherboard #WiFi #MCU #ReferenceDesign #project #ESP32 #camera #reusable #module #edgeComputing #espressif #template

10/100 Base-T/TX PHY Ethernet controller that supports PoE with SPI Interface. Based on W5500. Can be used as PoE injector. #project #referenceDesign #template #w5500 #PoE #EtherNet #RJ5

The Atmel® | SMART SAM9260, manufactured by Atmel, is an ARM-based Embedded Microprocessor Unit (MPU), integrating the ARM926EJ-STM processor operating at 180 MHz. This MPU includes substantial on-chip memory and extensive peripherals, including an Ethernet MAC, USB Device and Host Ports, along with various standard interfaces such as USART, SPI, TWI, Timer Counters, and MultiMedia Card Interface. Architected on a 6-layer matrix delivering a maximum internal bandwidth of six 32-bit buses, it supports external 32-bit bus interfaces for SDRAM, static memories, CompactFlash, and SLC NAND Flash with ECC. The SAM9260 is available in 217-ball LFBGA and 208-pin PQFP packages. Key features include 8 Kbytes each of data and instruction cache, integrated MMU, two internal 4-Kbyte SRAMs, a 32-Kbyte ROM with bootloader, 22 Peripheral DMA channels, various power-on reset modes, two programmable clock signals, advanced interrupt controller, and multiple power management options for optimized performance and energy efficiency.

This project is a Battery Management System (BMS) built around STMicroelectronics' STC3115AIQT battery monitor IC. It uses I2C for communication, features alarm management, and supports battery charging. The power supply, battery connection points, and debug interface are facilitated through connectors. #project #Template #charger #monitor #reusable #module #batterycharger #template #bms #STC3115 #stm

The NTK3134N from ON Semiconductor is a high-performance, single N-Channel MOSFET designed for power and interface switching applications in ultra-small portable electronics. Packaged in a compact SOT-723 form factor, which is 44% smaller in footprint and 38% thinner than the SC89, this MOSFET features a low RDS(on) for efficient load switching. It operates at low logic level gate drives, with a maximum drain-to-source voltage (VDSS) of 20V and a continuous drain current (ID) of up to 890mA at 25°C. The component supports pulsed drain currents up to 1.8A and boasts ESD protection. The NTK3134N is also Pb-Free, Halogen Free/BFR Free, and RoHS Compliant, making it an environmentally friendly choice for designers. Key applications include load/power switching, interface switching, logic level shifting, and battery management.

This project is a motherboard for the ESP32-CAM module, which enables easy and flexible WiFi camera applications. The motherboard provides power supply, programming interface, and GPIO expansion for the ESP32-CAM. It also supports external sensors for more functionality. #motherboard #WiFi #MCU #ReferenceDesign #project #ESP32 #camera #reusable #module #edgeComputing #espressif #template

This project is a motherboard for the ESP32-CAM module, which enables easy and flexible WiFi camera applications. The motherboard provides power supply, programming interface, and GPIO expansion for the ESP32-CAM. It also supports external sensors for more functionality. #motherboard #WiFi #MCU #ReferenceDesign #project #ESP32 #camera #reusable #module #edgeComputing #espressif #template

The "Green Dot 2040E5" Board is a Node that interfaces RS485 Sensor probes and can log information to the cloud using LoRa Connectivity. It uses the XIAO RP2040 and the LoRa-E5 (STM32WLE5JC) modules from Seeed Studio to do its magic. It also has amazing power management capabilities (Solar charging, Battery protection, etc) that make it very useful for IoT applications #SeeedStudio #XIAO #LoRa #RP2040 #IoT

1/1 Transceiver Half CANbus 8-DFN #CommonPartsLibrary #IntegratedCircuits #Interface #Drivers #Receivers #Transceivers #TJA1051

Design of an RGB LED control system using a TCA6424A I/O expander. Features multiple RGB LEDs driven by resistors via an I2C interface. Integrates power supply and reset circuitry. #polygon

Reference design for PCM5102A 2VRMS DirectPath™, 112dB Audio Stereo DAC with 32-bit, 384kHz PCM Interface #project-template #DAC #audio #project

This is a reference design of NCV7356D1R2G with a standard configuration for normal mode #NCV7356D1R2G #can #interface #transceiverCircuit #referenceDesign #canbus #onsemi #reference-design

This project is a minimalist Arduino Watch design. Consisting of a Microchip ATTINY85-20SU microcontroller, an OLED display for visual output, two user buttons for interface, and a Li-ion Battery for power. The schematic also includes graphic user interface with ISP for programming and minimal passive components for functionality. #project #Template #projectTemplate #referenceDesign #simple-embedded #microchip #arduino #template #reference-design .

10/100 Base-T/TX PHY Ethernet controller that supports PoE with SPI Interface. Based on W5500. Can be used as PoE injector. #project #referenceDesign #template #w5500 #PoE #EtherNet #RJ5

The "Green Dot 2040E5" Board is a Node that interfaces RS485 Sensor probes and can log information to the cloud using LoRa Connectivity. It uses the XIAO RP2040 and the LoRa-E5 (STM32WLE5JC) modules from Seeed Studio to do its magic. It also has amazing power management capabilities (Solar charging, Battery protection, etc) that make it very useful for IoT applications #SeeedStudio #XIAO #LoRa #RP2040 #IoT

This is a WiFi to Infrared (IR) gateway reference design leveraging an ESP32-S3 microcontroller for WiFi connectivity. It also incorporates a Type-C USB interface for data and power, 3 LEDs (red, green, & IR), and voltage regulation. It facilitates wireless control of IR devices, suitable for home automation projects. #referenceDesign #edge-computing #espressif #template #IR #project #reference-design

This is a reference design of TJA1051TK with a standard configuration for normal mode #TJA1051TK #can #interface #template #transceiverCircuit #referenceDesign #canbus #nxp #reference-design

A simple Arduino weather shield which allows an Arduino Uno R3 to interface with: ● Barometric pressure sensor ● Phototransistor ● Humidity Sensor ● Temperature Sensor #Arduino #Uno #Shield #Template #project-template #project

The Texas Instruments DAC3484 is a highly integrated, low-power, quad-channel, 16-bit digital-to-analog converter (DAC) capable of sample rates up to 1.25 GSPS. This component is designed to simplify complex transmit architectures in telecommunications and broadcast systems, offering features such as 2x to 16x digital interpolation filters with more than 90 dB of stop-band attenuation, which eases data interface and reconstruction filter design. Additionally, the DAC3484 includes independent complex mixers with fine and coarse mixing options for flexible carrier placement, a low jitter clock multiplying phase-locked loop (PLL) for simplified clocking, and digital Quadrature Modulator Correction (QMC) for IQ compensation in direct up-conversion applications. The 16-bit LVDS data bus, equipped with on-chip termination, a FIFO, data pattern checker, and parity test, along with multiple device synchronization capability, addresses the needs for high speed and precision in applications such as cellular base stations, diversity transmitters, and wideband communications. Offering options for very low power consumption and available in both 88-pin WQFN and 196-ball NFBGA packaging options, the DAC3484 is characterized for operation across the industrial temperature range of -40℃ to 85°C, making it a versatile choice for systems designers requiring high performance, multi-channel DAC solutions.

The TCA9555, manufactured by Texas Instruments, is a low-voltage 16-bit I/O expander designed for both I2C and SMBus for operation with a supply voltage ranging from 1.65 V to 5.5 V. This component is aimed at providing general-purpose remote I/O expansion for most microcontroller families through the I2C interface. The TCA9555 is characterized by its low standby-current consumption of maximum 3.5 uA and includes notable features such as open-drain active-low interrupt output, 5-V tolerant I/O ports, and configurable slave addresses through 3 address pins. It is designed to assist in applications such as servers, routers, personal computers, personal electronics, and industrial automation equipment, among others. Its multiple package options, including TSSOP, SSOP, WQFN, and VQFN, accommodate different sizes and form factors suitable for diverse implementation requirements. The device distinguishes itself with a polarity inversion register and latched outputs capable of directly driving LEDs, showcasing versatility in usage. Its protection features exceed JESD 22 standards for ESD, ensuring robustness for industrial applications. The TCA9555's compatibility with various microcontrollers and support for up to 400-kHz I2C bus speed make it an efficient solution for expanding I/O capabilities in space-constrained applications.

10/100 Base-T/TX PHY Ethernet controller that supports PoE with SPI Interface. Based on W5500. Can be used as PoE injector. #project #referenceDesign #template #w5500 #PoE #EtherNet #RJ5

JTAGulator copied from Joe Grand design. Allows to discover JTAG interfaces on embedded systems. Also allows to find UART interfaces. Is able to use OpenOCD to debug chips.

3.7V Lipo Charger. Interfaces with MT3608 Boost Converter to convert 3.7V to 5V. Slot on top of your Arduino and charge your battery while the Arduino is plugged in. Or run your Arduino portably using the battery.

The "Green Dot 2040E5" Board is a Node that interfaces RS485 Sensor probes and can log information to the cloud using LoRa Connectivity. It uses the XIAO RP2040 and the LoRa-E5 (STM32WLE5JC) modules from Seeed Studio to do its magic. It also has amazing power management capabilities (Solar charging, Battery protection, etc) that make it very useful for IoT applications #Seeed #XIOA #LoRa #RP2040 #IoT

This project is an RF-ID lock circuit, complete with microcontroller (MCU). It features an RC522 RFID reader for identification, controlled by an STM32F103C8T6 MCU. The structure also includes an OLED display, lock circuit, and user interface switches. Designed to operate with a AAA battery power source. #MCU #referenceDesign #simple-embedded #stm #project #STM32 #lock #OLED #template #reference-design