Finding USB-A Connector Parts
0:46
Searching for a component.
Searching.
Finished searching for a component.
Here are the closest matches for “RP2350-USB-A” in the Flux library, based on the Waveshare RP2350-USB-A USB-A receptacle you linked:
Table
| Part Name | MPN | Package Code | Datasheet |
|---|---|---|---|
| U231-091N-3GRC10-5 | U231-091N-3GRC10-5 | usb_a_type_female | |
| 914-441A3061D10201 | 914-441A3061D10201 | USB-A-TH_914-441A3061D10201 | — |
| 483910003 | 483910003 | USB-A-TH_4839100031 | — |
Recommendation:
The Waveshare RP2350-USB-A is a right-angle USB-A female receptacle. Of the above, U231-091N-3GRC10-5 most closely matches (3 A rating, right-angle Type-A female).
The Waveshare RP2350-USB-A is a right-angle USB-A female receptacle. Of the above, U231-091N-3GRC10-5 most closely matches (3 A rating, right-angle Type-A female).
Let me know if you’d like to add that one (or another) to your schematic!
308 days
0:44
Searching for a component.
Searching.
Finished searching for a component.
Checking if I can make the changes for you.
I can add the right-angle USB-A receptacle you need. Here’s the component I’ll place:
Let me know if you’d like me to go ahead and add it to your PCB layout.
308 days
Add usb C connector and do the connection for usb on s3
@copilot Add usb C connector and do the connection for usb on s3
1y
To connect a USB-C connector to the ESP32-S3-MINI-1U-N8, you will typically want to create connections that enable USB communication, which usually involves connecting USB data lines as well as providing power to the device.
Components Required
- USB-C Connector:
- Pins typically include VBUS, GND, D+, D-, and configuration pins for orientation detection.
- Resistors and Capacitors:
- CC resistors (typically around 5.1kΩ) for configuring the orientation of the connector.
- Decoupling capacitors for power filtering.
For the ESP32-S3, you primarily need to connect the USB data lines and power lines. Based on your design, here are the typical connections:
-
VCC (3.3V) Power Supply:
- Connect USB-C:VBUS to your system's power supply or 3V3, through a voltage regulator if necessary, to provide power to the ESP32.
-
Ground:
- Connect USB-C:GND to GND (any ground pin).
-
USB Data Lines:
- Connect USB-C:D+ to IO9 (or the appropriate USB data pin on your ESP32-S3).
- Connect USB-C:D- to IO8 (or the appropriate USB data pin on your ESP32-S3).
-
USB Configuration Channel (CC):
- Connect the CC1 and CC2 pins of the USB-C connector through a 5.1kΩ resistor to ground. This resistor helps in determining the cable orientation and power role.
- Make sure the power supply can handle the maximum current that your ESP32 will draw.
- Add decoupling capacitors close to the VCC pins on the ESP32-S3 to stabilize the voltage supply.
Would you like help selecting specific components, or do you have any additional requirements for this connection?
1y
Someone is typing...
3
Add USB C port and do the mapping to the esp32
@copilot Add USB C port and do the mapping to the esp32
1y
To add a USB-C port to your ESP32-S3-MINI-1U-N8 project and map it correctly, you need a USB-C connector and a USB-to-UART bridge (such as the CP2102N or CH340). This setup will allow you to program the ESP32 through USB and communicate via UART. Here's a step-by-step guide on how to make the connections:
Components Needed
- USB-C Connector
- USB-to-UART Bridge IC
- Supporting passive components (e.g., capacitors, resistors)
-
USB-C Connector:
- VBUS: Connect to the power input, providing power to your circuit.
- CC1, CC2: Connect pull-down resistors (typically 5.1kΩ) to ground. This helps in configuring the USB-C as a device.
- D+, D-: These are data lines. Connect to the USB-to-UART bridge.
-
USB-to-UART Bridge:
- VDD: Connect to the 3.3V rail ($3V3$).
- GND: Connect to ground ($GND$).
- TXD: Connect to ESP32-S3-MINI-1U-N8's RXD0 pin ($RXD0$).
- RXD: Connect to TXD0 pin ($TXD0$).
- D+, D- (from USB-C Connector): Connect these to the corresponding D+ and D- pins of the USB-to-UART bridge.
-
ESP32 Programming Pins:
- EN: Connect this through a pull-up resistor (typically 10kΩ) to 3.3V.
- IO0: To enter bootloader mode, you may need a button or some logic that can pull this pin low during boot.
- Connect USB-C:VBUS to 3V3:$3V3$
- Connect USB-C:CC1, CC2 to GND with 5.1kΩ resistors each.
- Connect USB-C:D+ to USB-to-UART Bridge:DP
- Connect USB-C:D- to USB-to-UART Bridge:DM
- Connect USB-to-UART Bridge:TXD to RXD0:$RXD0$ on the ESP32.
- Connect USB-to-UART Bridge:RXD to TXD0:$TXD0$ on the ESP32.
Does this setup fit your requirements? Let me know if you need further customization or additional information!
1y
Someone is typing...
2
IO21
IO19
EN
RXD0
IO2
IO1
IO20
3V3
IO0
TXD0
IO3
Reviews
- Wirelessly connects nets on schematic. Used to organize schematics and separate functional blocks. To wirelessly connect net portals, give them same designator. #portaljharwinbarrozo43.0M
- Wirelessly connects power nets on schematic. Identical to the net portal, but with a power symbol. Used to organize schematics and separate functional blocks. To wirelessly connect power net portals, give them the same designator. #portal #powerjharwinbarrozo11.4M
- A generic fixed resistor ideal for rapid circuit topology development. Its footprint automatically adapts based on the selected package case code—supporting 0402, 0603, 0805, 1203, and many other standard SMD packages, as well as axial horizontal and vertical configurations. Save precious design time by seamlessly add more information to this part (value, footprint, etc.) as it becomes available. Standard resistor values: 1.0 ohm, 10 ohm, 100 ohm, 1.0k ohm, 10k ohm, 100k ohm, 1.0M ohm 1.1 ohm, 11 ohm, 110 ohm, 1.1k ohm, 11k ohm, 110k ohm, 1.1M ohm 1.2 ohm, 12 ohm, 120 ohm, 1.2k ohm, 12k ohm, 120k ohm, 1.2M ohm 1.3 ohm, 13 ohm, 130 ohm, 1.3k ohm, 13k ohm, 130k ohm, 1.3M ohm 1.5 ohm, 15 ohm, 150 ohm, 1.5k ohm, 15k ohm, 150k ohm, 1.5M ohm 1.6 ohm, 16 ohm, 160 ohm, 1.6k ohm, 16k ohm, 160k ohm, 1.6M ohm 1.8 ohm, 18 ohm, 180 ohm, 1.8K ohm, 18k ohm, 180k ohm, 1.8M ohm 2.0 ohm, 20 ohm, 200 ohm, 2.0k ohm, 20k ohm, 200k ohm, 2.0M ohm 2.2 ohm, 22 ohm, 220 ohm, 2.2k ohm, 22k ohm, 220k ohm, 2.2M ohm 2.4 ohm, 24 ohm, 240 ohm, 2.4k ohm, 24k ohm, 240k ohm, 2.4M ohm 2.7 ohm, 27 ohm, 270 ohm, 2.7k ohm, 27k ohm, 270k ohm, 2.7M ohm 3.0 ohm, 30 ohm, 300 ohm, 3.0K ohm, 30K ohm, 300K ohm, 3.0M ohm 3.3 ohm, 33 ohm, 330 ohm, 3.3k ohm, 33k ohm, 330k ohm, 3.3M ohm 3.6 ohm, 36 ohm, 360 ohm, 3.6k ohm, 36k ohm, 360k ohm, 3.6M ohm 3.9 ohm, 39 ohm, 390 ohm, 3.9k ohm, 39k ohm, 390k ohm, 3.9M ohm 4.3 ohm, 43 ohm, 430 ohm, 4.3k ohm, 43K ohm, 430K ohm, 4.3M ohm 4.7 ohm, 47 ohm, 470 ohm, 4.7k ohm, 47k ohm, 470k ohm, 4.7M ohm 5.1 ohm, 51 ohm, 510 ohm, 5.1k ohm, 51k ohm, 510k ohm, 5.1M ohm 5.6 ohm, 56 ohm, 560 ohm, 5.6k ohm, 56k ohm, 560k ohm, 5.6M ohm 6.2 ohm, 62 ohm, 620 ohm, 6.2k ohm, 62K ohm, 620K ohm, 6.2M ohm 6.8 ohm, 68 ohm, 680 ohm, 6.8k ohm, 68k ohm, 680k ohm, 6.8M ohm 7.5 ohm, 75 ohm, 750 ohm, 7.5k ohm, 75k ohm, 750k ohm, 7.5M ohm 8.2 ohm, 82 ohm, 820 ohm, 8.2k ohm, 82k ohm, 820k ohm, 8.2M ohm 9.1 ohm, 91 ohm, 910 ohm, 9.1k ohm, 91k ohm, 910k ohm, 9.1M ohm #generics #CommonPartsLibraryjharwinbarrozo1.5M
- A generic fixed capacitor ideal for rapid circuit topology development. You can choose between polarized and non-polarized types, its symbol and the footprint will automatically adapt based on your selection. Supported options include standard SMD sizes for ceramic capacitors (e.g., 0402, 0603, 0805), SMD sizes for aluminum electrolytic capacitors, and through-hole footprints for polarized capacitors. Save precious design time by seamlessly add more information to this part (value, footprint, etc.) as it becomes available. Standard capacitor values: 1.0pF, 10pF, 100pF, 1000pF, 0.01uF, 0.1uF, 1.0uF, 10uF, 100uF, 1000uF, 10000uF 1.1pF, 11pF, 110pF, 1100pF 1.2pF, 12pF, 120pF, 1200pF 1.3pF, 13pF, 130pF, 1300pF 1.5pF, 15pF, 150pF, 1500pF, 0.015uF, 0.15uF, 1.5uF, 15uF, 150uF, 1500uF 1.6pF, 16pF, 160pF, 1600pF 1.8pF, 18pF, 180pF, 1800pF 2.0pF, 20pF, 200pF, 2000pF 2.2pF, 22pF, 220pF, 2200pF, 0.022uF, 0.22uF, 2.2uF, 22uF, 220uF, 2200uF 2.4pF, 24pF, 240pF, 2400pF 2.7pF, 27pF, 270pF, 2700pF 3.0pF, 30pF, 300pF, 3000pF 3.3pF, 33pF, 330pF, 3300pF, 0.033uF, 0.33uF, 3.3uF, 33uF, 330uF, 3300uF 3.6pF, 36pF, 360pF, 3600pF 3.9pF, 39pF, 390pF, 3900pF 4.3pF, 43pF, 430pF, 4300pF 4.7pF, 47pF, 470pF, 4700pF, 0.047uF, 0.47uF, 4.7uF, 47uF, 470uF, 4700uF 5.1pF, 51pF, 510pF, 5100pF 5.6pF, 56pF, 560pF, 5600pF 6.2pF, 62pF, 620pF, 6200pF 6.8pF, 68pF, 680pF, 6800pF, 0.068uF, 0.68uF, 6.8uF, 68uF, 680uF, 6800uF 7.5pF, 75pF, 750pF, 7500pF 8.2pF, 82pF, 820pF, 8200pF 9.1pF, 91pF, 910pF, 9100pF #generics #CommonPartsLibraryjharwinbarrozo1.5M
- A generic fixed inductor suitable for rapid circuit topology development. The footprint automatically adapts based on the selected package, supporting standard SMD sizes (e.g., 0402, 0603, 0805) as well as well-known inductor packages such as SDR1806, PA4320, SRN6028, and SRR1260. Standard inductor values: 1.0 nH, 10 nH, 100 nH, 1.0 µH, 10 µH, 100 µH, 1.0 mH 1.2 nH, 12 nH, 120 nH, 1.2 µH, 12 µH, 120 µH, 1.2 mH 1.5 nH, 15 nH, 150 nH, 1.5 µH, 15 µH, 150 µH, 1.5 mH 1.8 nH, 18 nH, 180 nH, 1.8 µH, 18 µH, 180 µH, 1.8 mH 2.2 nH, 22 nH, 220 nH, 2.2 µH, 22 µH, 220 µH, 2.2 mH 2.7 nH, 27 nH, 270 nH, 2.7 µH, 27 µH, 270 µH, 2.7 mH 3.3 nH, 33 nH, 330 nH, 3.3 µH, 33 µH, 330 µH, 3.3 mH 3.9 nH, 39 nH, 390 nH, 3.9 µH, 39 µH, 390 µH, 3.9 mH 4.7 nH, 47 nH, 470 nH, 4.7 µH, 47 µH, 470 µH, 4.7 mH 5.6 nH, 56 nH, 560 nH, 5.6 µH, 56 µH, 560 µH, 5.6 mH 6.8 nH, 68 nH, 680 nH, 6.8 µH, 68 µH, 680 µH, 6.8 mH 8.2 nH, 82 nH, 820 nH, 8.2 µH, 82 µH, 820 µH, 8.2 mH #generics #CommonPartsLibraryjharwinbarrozo15.8k
- An electrical connector acting as reusable interface to a conductor and creating a point where external circuits can be connected.Terminal
- 47 kOhms ±5% 0.125W, 1/8W Chip Resistor 0805 (2012 Metric) Automotive AEC-Q200 Thick Film #forLedBlinkjharwinbarrozo1.2M
- 10uF Capacitor Aluminum Polymer 20% 16V SMD 5x5.3mm #forLedBlink #commonpartslibrary #capacitor #aluminumpolymer #radialcanjharwinbarrozo1.2M
- Yellow 595nm LED Indication - Discrete 1.7V 1206 (3216 Metric) #forLedBlinkjharwinbarrozo1.1M
ESP32-S3-MINI-1U-N8
Properties
Integrated Circuit
Espressif Systems
ESP32-S3-MINI-1U-N8
ESP
parametric-v1
Pricing & Availability
Distributor | Qty 1 |
|---|
Controls
Welcome 👋
Flux accelerates your PCB design with AI.
Create your account to start using this component and bring your ideas to life.
picknicker
copilot
- You want to connect these modules using a UART interface.
- We'll use one of the available UART ports on the ESP32-S3-MINI-1U.
- We'll assume the USR-C210 is powered separately, or you have a power arrangement that handles both devices.
Connections:- Ground Connection:
- Ensure both devices share a common ground: Connect one of the GND pins of the USR-C210 to one of the GND pins on the ESP32-S3-MINI-1U.
UART Configuration:- Configure the UART settings on the ESP32 to match those required by the USR-C210, typically 9600 or 115200 baud, 8 data bits, no parity, and 1 stop bit (8N1).
Considerations: