Buck Switching Regulator IC Positive Adjustable 1.2V 1 Output 3.5A 8-PowerSOIC (0.154", 3.90mm Width) The LM5013DDAR is a 100-V input, 3.5-A buck switching regulator IC that efficiently steps down high DC voltages (such as 24 V, 48 V, or battery rails) to lower regulated outputs. It is optimized for rugged environments where wide input variations and high reliability are required. It features ultra-low quiescent current operation, making it suitable for systems that require high efficiency even at light load or standby conditions. Key Features Wide input voltage range: 6 V to 100 V Up to 3.5 A output current capability Integrated 100-V high-side MOSFET Non-synchronous buck topology Ultra-low quiescent current (IQ) for high efficiency in standby Constant-on-time (COT) control for fast transient response No external compensation components required Adjustable output voltage (down to ~1.2 V reference) 50 ns minimum on/off time for high step-down ratios Built-in protection features: Overcurrent protection Thermal shutdown Input undervoltage lockout (UVLO) Open-drain power-good (PGOOD) signal for system monitoring Meets low EMI requirements (CISPR 25 Class 5 capable) Package 8-pin SO PowerPAD (DDA) surface-mount package Designed for good thermal performance in high-voltage applications Typical Applications Industrial power supplies (24 V / 48 V systems) Automotive power systems Telecom and networking equipment High cell-count battery systems Motor control and inverter subsystems #LM5013 #BuckConverter #DCDCConverter #TexasInstruments #PowerManagementIC #HighVoltageRegulator #3ARegulator #IndustrialPower #AutomotiveElectronics #SwitchingRegulator #COTController

Automotive, 60-V, 6-A, 30-mΩ, one-channel smart high-side switch with adjustable current limit TPS1HTC30-Q1 is a single-channel, smart high-side switch, with integrated NMOS power FET and charge pump, designed to meet the requirements of 24-V automotive battery systems. The low RON(30 mΩ) minimizes device power dissipation driving a wide range of output load current up to 6-A DC, and the 60- V DC operating range improves system robustness. The device integrates protection features such as thermal shutdown, output clamp, and current limit. These features improve system robustness during fault events such as short circuit. TPS1HTC30-Q1 implements an adjustable current limiting circuit that improves the reliability of the system by reducing inrush current when driving large capacitive loads and minimizing overload current. The device also provides an accurate load current sense that allows for improved load diagnostics such as overload and open-load detection enabling better predictive maintenance. TPS1HTC30-Q1 is available in a small 14-pin, 4.40- mm × 5.0-mm HTSSOP leaded package with 0.65- mm pin pitch minimizing the PCB footprint. • Single-channel smart high-side power switch for 24-V automotive systems with full diagnostics • Wide operating voltage range: 6 V to 60 V – OVP protection: 66 V • Low RON: 30-mΩ typical, 55-mΩ maximum • Low standby current: < 0.5 µA • Low quiescent current (Iq): < 2 mA • Improve system level reliability through adjustable current limiting – Current limit: 2 A –16 A • Accurate current sensing: ±4% at 1 A • Protection – Overload and short-circuit protection – Integrated inductive discharge clamp – Undervoltage lockout (UVLO) protection – Loss of GND, loss of supply protection – Reverse battery protection with external components • Diagnostics – On and off state output open-load and short-tobattery detection – Overload and short to ground detection – Absolute and relative thermal shutdown detection • Functional Safety-Capable – Documentation available to aid functional safety system design • Operating junction temperature: –40 to 125°C • Input control: 1.8-V, 3.3-V and 5-V logic compatible • Integrated fault sense voltage scaling for ADC protection • Qualifications – AEC-Q100 qualified for automotive applications • Temperature grade 1: –40°C to +125°C, TA • 14-pin thermally-enhanced TSSOP package TPS1HTC30AQPWPRQ1 #CommonPartsLibrary #IntegratedCircuit

Single-channel high-speed low-side MOSFET/IGBT gate driver with 4-A source/8-A sink, split outputs for independent turn-on/off control, dual inverting/noninverting inputs, 4.5–18 V supply, 13 ns typical delay, and UVLO in SOT-23-6.

Bipolar Motor Driver NMOS On/Off, PWM 44-HTSSOP The DRV8262QDDWRQ1 is an automotive-qualified, high-power H-bridge motor driver from Texas Instruments designed for 24 V and 48 V automotive systems. It integrates two H-bridges capable of driving one or two brushed DC motors, a bipolar stepper motor, or thermoelectric coolers (TECs). The device features integrated high-side current sensing, programmable current regulation, and comprehensive protection functions, eliminating the need for external current-sense resistors while reducing PCB area and system cost. It supports wide supply voltages from 4.5 V to 60 V, making it suitable for demanding automotive body electronics and industrial motor control applications. Key Features Automotive AEC-Q100 Grade 1 qualified (-40°C to +125°C) Wide 4.5 V to 60 V operating supply voltage Dual H-bridge or single high-current H-bridge operation Drives: One or two brushed DC motors One bipolar stepper motor One or two thermoelectric coolers (TECs) Up to 8 A peak (dual H-bridge mode) Up to 16 A peak (single H-bridge mode) Low MOSFET on-resistance: 100 mΩ (dual H-bridge) 50 mΩ (single H-bridge) Integrated high-side current sensing with ±4% accuracy Programmable current regulation and current limiting Supports 1.8 V, 3.3 V, and 5 V logic interfaces Configurable PWM control modes (PH/EN or IN/IN) Ultra-low 3 µA sleep current Integrated protection features: Undervoltage Lockout (UVLO) Charge Pump Undervoltage (CPUV) Overcurrent Protection (OCP) Thermal Shutdown (OTSD) Fault output (nFAULT) Functional safety-capable with supporting documentation for automotive system design. #DRV8262QDDWRQ1 #MotorDriver #HBridge #AutomotiveElectronics #BrushedDCMotor #StepperMotor #CurrentSense #AECQ100 #TexasInstruments #EmbeddedSystems #PowerManagement #PCBDesign

Buck Switching Regulator IC Positive Fixed 3.3V 1 Output 2A SOT-23-6 Thin, TSOT-23-6 The AP63200/AP63201/AP63203/AP63205 is a 2A, synchronous buck converter with a wide input voltage range of 3.8V to 32V and fully integrates a 125mΩ high-side power MOSFET and a 68mΩ low-side power MOSFET to provide high-efficiency step-down DC/DC conversion. The AP63200/AP63201/AP63203/AP63205 device is easily used by minimizing the external component count due to its adoption of peak current mode control along with its integrated compensation network. The AP63200/AP63201/AP63203/AP63205 has optimized designs for Electromagnetic Interference (EMI) reduction. The converter features Frequency Spread Spectrum (FSS) with a switching frequency jitter of ±6%, which reduces EMI by not allowing emitted energy to stay in any one frequency for a significant period of time. It also has a proprietary gate driver scheme to resist switching node ringing without sacrificing MOSFET turn-on and turn-off times, which further erases highfrequency radiated EMI noise caused by MOSFET switching. The device is available in a low-profile, TSOT26 package. • VIN 3.8V to 32V • 2A Continuous Output Current • 0.8V ±1% Reference Voltage • 22µA Ultralow Quiescent Current • Switching Frequency o 500kHz: AP63200 and AP63201 o 1.1MHz: AP63203 and AP63205 • Pulse Width Modulation (PWM) Regardless of Output Load o AP63201 • Supports Pulse Frequency Modulation (PFM) o AP63200, AP63203, and AP63205 o Up to 80% Efficiency at 1mA Light Load o Up to 88% Efficiency at 5mA Light Load • Fixed Output Voltage o 3.3V: AP63203 o 5.0V: AP63205 • Proprietary Gate Driver Design for Best EMI Reduction • Frequency Spread Spectrum (FSS) to Reduce EMI • Precision Enable Threshold to Adjust UVLO • Protection Circuitry o Overvoltage Protection o Cycle-by-Cycle Peak Current Limit o Thermal Shutdown • 12V and 24V distributed power bus supplies • Flat screen TV sets and monitors • Power tools and laser printers • White goods and small home appliances • FPGA, DSP, and ASIC supplies • Home audios • Network systems • Set top boxes • Gaming consoles • Consumer electronics #commonpartslibrary #integratedcircuit #AP63203WU7 #BuckConverter #DCDCConverter #PowerManagement #VoltageRegulator #SynchronousBuck #EmbeddedSystems #IndustrialElectronics #PowerSupply #DiodesInc #3V3Power #ElectronicsDesign

The TPS54331 device is a 28-V, 3-A nonsynchronous buck converter that integrates a low RDS(on) high-side MOSFET. To increase efficiency at light loads, a pulse skipping Eco-mode feature is automatically activated. Furthermore, the 1-μA shutdown supply-current allows the device to be used in battery-powered applications. Current mode control with internal slope compensation simplifies the external compensation calculations and reduces component count while allowing the use of ceramic output capacitors. A resistor divider programs the hysteresis of the input undervoltage lockout. An overvoltage transient protection circuit limits voltage overshoots during start-up and transient conditions. A cycle-by-cycle current-limit scheme, frequency foldback and thermal shutdown protect the device and the load in the event of an overload condition. The TPS54331 device is available in an 8-pin SOIC package and 8-pin SO PowerPAD integrated circuit package that have been internally optimized to improve thermal performance. • 3.5 to 28-V input voltage range • Adjustable output voltage down to 0.8 V • Integrated 80-mΩ high-side MOSFET supports up to 3-A continuous output current • High efficiency at light loads with a pulse skipping Eco-mode • Fixed 570-kHz switching frequency • Typical 1-μA shutdown quiescent current • Adjustable slow-start limits inrush currents • Programmable UVLO threshold • Overvoltage transient protection • Cycle-by-cycle current limit, frequency foldback, and thermal shutdown protection • Available in easy-to-use SOIC8 package or thermally-enhanced SOIC8 PowerPAD™ integrated circuit package • Create a custom design using the TPS54331 with the WEBENCH® Power Designer • Use TPS62933 for a 30 VIN converter with higher frequency, lower IQ and improved EMI #CommonPartsLibrary #IntegratedCircuit #PowerManagement

High voltage half-bridge gate driver for GaN transistors Features • dV/dt immunity ±200 V/ns • Driver current capability: – 1.3/2.4 A source/sink typ @ 25 °C, 6 V – 5.5/6 A source/sink typ @ 25 °C, 15 V • Separated turn on and turn off gate driver pins • 45 ns propagation delay with tight matching • 3.3 V, 5 V TTL/CMOS inputs with hysteresis • Interlocking function • UVLO on low-side and high-side sections • Dedicated pin for shut down functionality • Over temperature protection Applications • High-voltage PFC, DC-DC and DC-AC converters • Switch-mode power supplies • UPS systems • Solar power • Motor driver for home appliances, factory automation and industrial drives. #CommonPartsLibrary #IntegratedCircuit #powermanagement

Buck Switching Regulator IC Positive Fixed 5V 1 Output 1A SOT-23-6 The LMR50410Y5FQDBVRQ1 (part of the LMR50410-Q1 family from Texas Instruments) is a synchronous step-down (buck) DC-DC converter designed for automotive and industrial power applications. It operates over a wide input voltage range of 4 V to 36 V and can deliver up to 1 A output current, making it suitable for converting higher, unregulated voltages into stable lower voltages (e.g., 5 V or 3.3 V rails). The device integrates power switches, control circuitry, and compensation internally, allowing simple design with minimal external components and a compact PCB footprint. Key Features Power & Performance Wide input voltage range: 4 V to 36 V Output current: up to 1 A High switching frequency: 2.1 MHz (enables small inductors) High efficiency with PFM (light load) and FPWM (constant frequency) options Integration & Ease of Use Synchronous rectification (integrated high-side & low-side MOSFETs) Internal compensation (no complex external tuning) Minimal external components required Small SOT-23-6 package for compact designs Protection & Reliability Cycle-by-cycle current limit Short-circuit protection (hiccup mode) Thermal shutdown protection Undervoltage lockout (UVLO) ±1% reference voltage accuracy Automotive & Industrial Capability AEC-Q100 qualified (automotive grade) Operating temperature: Ambient: up to 125°C Junction: up to 150°C Designed for rugged automotive environments Additional Features Soft-start for controlled startup Precision enable pin for system control Monotonic startup with pre-biased output Available in fixed output (e.g., 5 V) variants Typical Applications Automotive electronics (ADAS, infotainment, lighting) Industrial power supplies Distributed power systems General-purpose DC-DC regulation #commonpartslibrary #integratedcircuit #powermanagement #voltageregulator

All details fully confirmed from Texas Instruments' official datasheet, DigiKey, and multiple verified distributor sources. Here's the complete spec. Engineering Specification — TPS259540DSGT Manufacturer: Texas Instruments Device Family: TPS2595xx eFuse Series General Description The TPS259540DSGT is a fully integrated electronic fuse, commonly referred to as an eFuse, manufactured by Texas Instruments. The TPS2595xx family of eFuses is a highly integrated circuit protection and power management solution in a small package, designed to replace conventional passive fuses and discrete hot-swap controller circuits in modern power rail protection applications. Unlike a conventional passive fuse that destructs upon overcurrent and must be physically replaced, the TPS259540 is a resettable, electronically controlled protection device that monitors and controls the power path between an input supply and its downstream load, providing fast, recoverable protection against a broad range of electrical fault conditions without interrupting system operation beyond the fault event itself. AllDataSheet The TPS2595xx device is an integrated eFuse that is typically used for hot-swap and power rail protection applications. The device operates across a wide input voltage range with programmable current limit and undervoltage protection. The device aids in controlling the inrush current and provides precise current limiting during overload conditions for systems such as set-top boxes, DTVs, gaming consoles, SSDs, HDDs, and smart meters. The device also provides robust protection for multiple faults on the sub-system rail. Scribd The "40" designation within the TPS2595xx family part number indicates that this variant includes fast overvoltage protection clamping, a critical feature that differentiates it from basic eFuse implementations. Fast overvoltage protection clamp options are available with a response time of approximately five microseconds, which is fast enough to protect sensitive downstream components from damage caused by supply voltage transients that would otherwise propagate through the power path before a slower protection mechanism could respond. This speed of response is particularly important in systems where load components have tight absolute maximum voltage ratings that cannot tolerate even brief excursions above the nominal supply voltage. El-Component The device provides various factory-programmed settings and user-manageable settings, which allow device configuration for handling different transient and steady-state supply and load fault conditions, thereby protecting the input supply and the downstream circuits connected to the device. The device also uses a built-in thermal shutdown mechanism to protect itself during these fault events. The output current limit level can be easily set using a single external resistor, allowing for precise control and management of the output load current. Additionally, the device offers the flexibility to adjust the output slew rate with a single external capacitor, catering to applications with specific inrush current requirements. ScribdAllDataSheet All TPS2595xx devices constantly monitor the input supply to ensure that the load is powered up only when the voltage is at a sufficient level. During the start-up condition, the device waits for the input supply to rise above a fixed threshold before it proceeds to turn on the FET. Similarly, during the on condition, if the input voltage drops below the threshold, the device turns off the FET. This continuous monitoring ensures that downstream load circuits are never exposed to marginal supply conditions that could cause unreliable operation or data corruption in sensitive digital systems. Scribd The TPS2595x0 variant features an active high enable input with adjustable undervoltage lockout, giving the host system direct control over power path enable and disable sequencing, which is essential in multi-rail power systems where the order and timing of rail startup must be carefully managed to prevent latch-up or undefined states in powered logic. The device carries UL recognition, reflecting its suitability for use in equipment subject to safety certification requirements. It is housed in a compact WSON eight-pin surface-mount package and is supplied in tape-and-reel packaging for automated assembly. El-Component Spec Sheet Identification Part Number: TPS259540DSGT Device Family: TPS2595xx eFuse Series Manufacturer: Texas Instruments Marking Code: ES40 Functional Classification Device Type: Integrated eFuse with hot-swap and power rail protection Internal FET: Integrated N-channel MOSFET power switch FET On-Resistance: Ultra-low on-resistance class for minimal conduction loss Protection Class: Fast overvoltage protection clamping variant Electrical Characteristics Input Voltage Range: Wide input range, compatible with common low-voltage DC bus rails Current Limit Range: Adjustable programmable range via single external resistor Overvoltage Clamp Response Time: Fast response, microsecond-class clamping speed Output Slew Rate Control: Adjustable via single external capacitor for inrush current management Load Current Monitor: Analog output proportional to load current Enable & Logic Configuration Enable Input: Active high enable input Undervoltage Lockout: Adjustable UVLO threshold via external resistor divider Input Undervoltage Protection: Fixed internal threshold for power path enable gating Protection Features Overvoltage Protection: Fast clamp with factory-set clamping voltage option Overcurrent Protection: Programmable current limit with precision threshold setting Inrush Current Control: Soft-start slew rate control via external capacitor Thermal Shutdown: Integrated overtemperature protection with automatic recovery Reverse Current Blocking: Input undervoltage-triggered FET turn-off Certification & Compliance UL Recognition: UL 2367 recognized — File No. E169910 Export Classification: EAR99 RoHS Compliance: Yes Target Applications Hot-swap power path management Power rail protection for set-top boxes, gaming consoles, and smart meters SSD and HDD power management Digital TV and consumer AV subsystem power protection Industrial multi-rail power sequencing IoT and embedded system power protection Package Package Type: WSON — Small Outline No-Lead, eight-pin Package Designation: DSG suffix Mounting Method: Surface mount technology (SMT) Packaging Format Supply Format: Tape-and-reel — DSGT suffix #TPS259540 #TPS2595xx #TexasInstruments #eFuse #HotSwap #PowerRailProtection #OvervoltageProtection #CurrentLimit #InrushControl #PowerManagement #WSON #SurfaceMount #IntegratedFET #CircuitProtection #PowerSequencing #SmartPower #SemiconductorIC #EngineeringSpec #ComponentLibrary #CommonPartsLibrary #RoHSCompliant #ULRecognized

Linear Voltage Regulator IC Positive Fixed 1 Output 500mA SOT-23-5 The TLV75533PDBVR is a low-dropout (LDO) linear voltage regulator designed to provide a stable 3.3 V output from a higher input voltage source. It features ultra-low quiescent current and high power-supply rejection ratio (PSRR), making it ideal for battery-powered and noise-sensitive applications such as IoT devices, portable electronics, and RF circuits. The device is optimized for fast transient response and stable operation with small ceramic output capacitors. Key Features Fixed output voltage: 3.3 V Low dropout voltage (typ. ~200 mV at full load) Ultra-low quiescent current (typ. 25 µA) High PSRR for noise-sensitive applications Stable with small ceramic capacitors (≥1 µF) Thermal shutdown and overcurrent protection Available in compact SOT-23-5 package (DBV) Absolute Maximum Ratings Input voltage: –0.3 V to 6.5 V Output voltage: –0.3 V to (VIN + 0.3 V) Operating junction temperature: –40°C to +125°C Storage temperature range: –65°C to +150°C Recommended Operating Conditions Input voltage range: 1.45 V to 5.5 V Output voltage: 3.3 V (fixed) Output current: up to 500 mA Operating temperature range: –40°C to +125°C Electrical Characteristics (Typical unless otherwise noted) Output voltage accuracy: ±1% Dropout voltage: ~200 mV @ 500 mA Quiescent current: ~25 µA PSRR: up to 70 dB (at 1 kHz) Line regulation: <0.05%/V Load regulation: <0.5% Pin Configuration (SOT-23-5) Pin 1: IN – Input voltage Pin 2: GND – Ground Pin 3: EN – Enable (active high) Pin 4: NC – No connect Pin 5: OUT – Regulated output Typical Application Power management for microcontrollers and sensors Battery-powered portable devices RF and analog circuits requiring low noise supply IoT and wearable electronics Protection Features Thermal shutdown protection Overcurrent protection Undervoltage lockout (UVLO) #commonpartsLibrary #integratedcircuit #powermanagement #voltageregulator

Ultra-Low Quiescent Current LDO Voltage Regulator – Fixed 3.3 V low-dropout (LDO) linear voltage regulator delivering up to 150 mA output current for battery-powered devices, portable electronics, sensors, wireless modules, and embedded systems. Operates from a 2.3 V to 5.5 V input voltage and features an ultra-low 21 µA typical quiescent current, 135 mV maximum dropout voltage at 150 mA, and 60 dB PSRR at 10 kHz for efficient, low-noise power regulation. Includes an enable (EN) input, low shutdown current (<1 µA typical), overcurrent protection, thermal shutdown, and undervoltage lockout (UVLO). Optimized for use with 1 µF ceramic capacitors, operates over a −40°C to +125°C temperature range, and is housed in a 5-pin TSOT-23 package. #AnalogDevices #ADP121AUJZ33R7 #ADP121 #LDO #LinearRegulator #VoltageRegulator #LowDropout #PowerManagement #150mA #LowPower #TSOT23 #EmbeddedSystems

Single-Channel EiceDRIVER With True Differential Inputs, 4V UVLO, +4/-8A, SOT-23-6 Driver, Dual MOSFET SOT?23*

Electronic Fuse Regulator 4A 8-WSON (2x2) eFuse providing input power-path protection with adjustable current limiting and fast overvoltage protection for 3 V to 18 V input supplies, supporting 0.5 A to 4 A load current. The TPS259535DSGR features 34 mΩ typical on-resistance, a 5.7 V typical output overvoltage clamp, auto-retry after thermal shutdown, active-high enable with adjustable UVLO, and quick output discharge, all in an 8-pin WSON package. #TexasInstruments #TPS259535DSGR #eFuse #PowerManagement #HotSwap #OvervoltageProtection #CurrentLimiting #UVLO #QuickOutputDischarge #WSON8

3A 55V Boost Converter with Programmable Switching Frequency and UVLO #ultralibrarian