8-Channel Single ADC SAR 14ksps 12-bit Serial Automotive 20-Pin TSSOP #commonpartslibrary #ADC #integratedcircuit

LED Driver IC 16 Output Linear PWM Dimming 25mA 5.5V 28-TSSOP PCA9685PW,118 is a 16-channel, 12-bit PWM LED controller with an I²C interface designed for LED dimming, RGB/RGBA lighting, and servo motor control applications. It provides independent PWM control for up to 16 outputs, allowing precise brightness or position control while minimizing MCU GPIO usage. The device supports Fast-mode Plus I²C communication up to 1 MHz and operates from a 2.3 V to 5.5 V supply range. It is commonly used in robotics, LED backlighting, automation systems, and PWM expansion modules for microcontrollers such as Arduino, ESP32, and Raspberry Pi. Key Features 16 independent PWM output channels 12-bit PWM resolution (4096 steps) Programmable PWM frequency from approximately 24 Hz to 1526 Hz I²C Fast-mode Plus compatible interface up to 1 MHz Six hardware address pins allowing up to 62 devices on one I²C bus Programmable open-drain or totem-pole outputs Output capability: 25 mA sink current 10 mA source current Internal 25 MHz oscillator with optional external clock input Individual programmable LED ON/OFF timing for reduced EMI and current surges Supports software reset and group addressing (All Call/Sub Call) 5.5 V tolerant inputs and outputs Operating voltage range: 2.3 V to 5.5 V Package: 28-pin TSSOP (PW suffix) #CommonPartsLibrary #IntegratedCircuit #PowerManagement #LEDdriver

Automotive, 60-V, 6-A, 30-mΩ, one-channel smart high-side switch with adjustable current limit TPS1HTC30-Q1 is a single-channel, smart high-side switch, with integrated NMOS power FET and charge pump, designed to meet the requirements of 24-V automotive battery systems. The low RON(30 mΩ) minimizes device power dissipation driving a wide range of output load current up to 6-A DC, and the 60- V DC operating range improves system robustness. The device integrates protection features such as thermal shutdown, output clamp, and current limit. These features improve system robustness during fault events such as short circuit. TPS1HTC30-Q1 implements an adjustable current limiting circuit that improves the reliability of the system by reducing inrush current when driving large capacitive loads and minimizing overload current. The device also provides an accurate load current sense that allows for improved load diagnostics such as overload and open-load detection enabling better predictive maintenance. TPS1HTC30-Q1 is available in a small 14-pin, 4.40- mm × 5.0-mm HTSSOP leaded package with 0.65- mm pin pitch minimizing the PCB footprint. • Single-channel smart high-side power switch for 24-V automotive systems with full diagnostics • Wide operating voltage range: 6 V to 60 V – OVP protection: 66 V • Low RON: 30-mΩ typical, 55-mΩ maximum • Low standby current: < 0.5 µA • Low quiescent current (Iq): < 2 mA • Improve system level reliability through adjustable current limiting – Current limit: 2 A –16 A • Accurate current sensing: ±4% at 1 A • Protection – Overload and short-circuit protection – Integrated inductive discharge clamp – Undervoltage lockout (UVLO) protection – Loss of GND, loss of supply protection – Reverse battery protection with external components • Diagnostics – On and off state output open-load and short-tobattery detection – Overload and short to ground detection – Absolute and relative thermal shutdown detection • Functional Safety-Capable – Documentation available to aid functional safety system design • Operating junction temperature: –40 to 125°C • Input control: 1.8-V, 3.3-V and 5-V logic compatible • Integrated fault sense voltage scaling for ADC protection • Qualifications – AEC-Q100 qualified for automotive applications • Temperature grade 1: –40°C to +125°C, TA • 14-pin thermally-enhanced TSSOP package TPS1HTC30AQPWPRQ1 #CommonPartsLibrary #IntegratedCircuit

Single-channel high-side N-channel smart power switch for power distribution, supporting a 6 V to 18 V load voltage and up to 11 A continuous output current. Features 8.8 mΩ typical ON resistance, non-inverting ON/OFF control, and integrated overcurrent, overvoltage, short-circuit, and undervoltage lockout (UVLO) protection. Specified for operation over a −40°C to +150°C junction temperature range and housed in a PG-TSDSO-14-22 (14-pin TSSOP exposed pad) package. #Infineon #BTS70081EPPXUMA1 #SmartPowerSwitch #HighSideSwitch #LoadSwitch #PowerDistribution #PROFET #NChannel #11A #PowerManagement #AutomotiveElectronics #TSDSO14

Battery Monitoring/Battery Balancer Li-Ion/Li-FePO4 20-Pin TSSOP T/R #BatteryManagement #commonpartslibrary

32 Bit Analog to Digital Converter 5, 10 Input 1 Sigma-Delta 28-TSSOP The ADS1263IPW is a high-precision, low-noise analog-to-digital converter designed for demanding industrial, instrumentation, and sensor measurement applications. Manufactured by Texas Instruments, this device integrates a delta-sigma ADC architecture with programmable gain amplification, precision voltage reference support, sensor biasing functions, and extensive diagnostic capabilities. It is optimized for applications requiring extremely high resolution and accuracy when measuring low-level analog signals. The device supports direct interfacing to bridge sensors, thermocouples, RTDs, pressure sensors, strain gauges, and other precision transducers. Integrated system monitoring and fault detection features simplify implementation in safety-critical and high-reliability systems. Flexible input multiplexing and multiple data-rate options allow the converter to be used across a wide range of precision data acquisition applications. The ADS1263IPW communicates through a standard SPI-compatible serial interface and operates from low-voltage analog and digital supplies. The device is packaged in a thermally efficient TSSOP package suitable for compact embedded system designs. Electrical Characteristics The converter utilizes a delta-sigma ADC core with extremely high effective resolution and low input-referred noise performance. It supports differential and single-ended analog input configurations with programmable gain settings for low-level sensor measurements. The integrated programmable gain amplifier supports multiple gain selections for direct amplification of small analog signals. The converter includes internal offset and gain calibration functions to improve system-level measurement accuracy. The device provides low drift characteristics and high common-mode rejection performance suitable for precision industrial environments. Analog Features The converter supports multiple analog input channels through an integrated input multiplexer. Internal sensor bias current sources are available for RTD and resistive sensor excitation applications. Integrated digital filtering options allow optimization between noise performance and conversion speed. Simultaneous rejection of power-line interference frequencies is supported for industrial measurement systems. The device includes internal temperature sensing and diagnostic monitoring functions for enhanced system reliability. Digital Interface Communication is implemented through an SPI-compatible serial interface supporting flexible host controller integration. The interface supports command-based register access, data readback, and configuration management. Programmable data rates allow balancing between throughput and precision requirements. Power Requirements The device operates from separate analog and digital supply rails to improve noise isolation and measurement accuracy. Low-power operating modes are supported for energy-sensitive applications. Protection and Diagnostics Integrated fault detection and monitoring functions include sensor open-circuit detection, reference monitoring, supply monitoring, and internal self-test capability. These features improve reliability in industrial and safety-oriented systems. Package Information The ADS1263IPW is supplied in a TSSOP package with fine-pitch lead spacing suitable for high-density PCB layouts and automated assembly processes. Typical Applications Industrial process control systems Precision data acquisition equipment Temperature measurement systems Pressure and bridge sensor interfaces Weigh scale and load-cell instrumentation Laboratory and test instrumentation Medical instrumentation Energy monitoring and metering systems #commonpartslibrary #integratedcircuit #analog #digital #converter

ARM® Cortex®-M0+ MSPM0 C Microcontroller IC 32-Bit 24MHz 16KB (16K x 8) FLASH 8-DSBGA (0.86x1.6) MSPM0C110x microcontrollers (MCUs) are part of the MSP highly-integrated ultra-low-power 32-bit MCU family based on the enhanced Arm® Cortex®-M0+ core platform operating at up to 24MHz frequency. These costoptimized MCUs offer high-performance analog peripheral integration, support extended temperature ranges from -40°C to 125°C, and operate with supply voltages from 1.62V to 3.6V. The MSPM0C110x devices provide up to 16KB embedded flash program memory with 1KB SRAM. These MCUs incorporate a high-speed on-chip oscillator with an accuracy from -2% to +1.2%, eliminating the need for an external crystal. Additional features include a 1-channel DMA, CRC-16 accelerator, and a variety of highperformance analog peripherals such as one 12-bit 1.5Msps ADC with VDD as the voltage reference, and an on-chip temperature sensor. These devices also offer intelligent digital peripherals such as one 16-bit advanced timer, two 16-bit general purpose timer, one windowed watchdog timer, and a variety of communication peripherals including one UART, one SPI, and one I2C. These communication peripherals offer protocol support for LIN, IrDA, DALI, Manchester, smart card, SMBus, and PMBus. The TI MSPM0 family of low-power MCUs consists of devices with varying degrees of analog and digital integration let customers find the MCU that meets their project needs. The architecture combined with extensive low-power modes is optimized to achieve extended battery life in portable measurement applications. MSPM0C110x MCUs are supported by an extensive hardware and software ecosystem with reference designs and code examples to get the design started quickly. Development kits include a LaunchPad™ kit available for purchase and design files for a target-socket board. TI also provides a free MSP Software Development Kit (SDK), which is available as a component of Code Composer Studio™ IDE desktop and cloud version within the TI Resource Explorer. MSPM0 MCUs are also supported by extensive online collateral, training with MSP Academy, and online support through the TI E2E™ support forums. Features • Core – Arm® 32-bit Cortex®-M0+ CPU, frequency up to 24MHz • Operating characteristics – Extended temperature: –40°C to 125°C – Wide supply voltage range: 1.62V to 3.6V • Memories – Up to 16KB of flash – 1KB of SRAM • High-performance analog peripherals – One analog-to-digital converter (ADC) with up to 10 total external channels, 1.7Msps at 10 bit or 1.5Msps at 12 bit with VDD as the voltage reference – Configurable 1.4V or 2.5V internal ADC voltage reference (VREF) – Integrated temperature sensor – Integrated supply monitor • Optimized low-power modes – RUN: 87µA/MHz – STOP: 609µA at 4MHz, 311µA at 32kHz – STANDBY: 5µA with SRAM retention – SHUTDOWN: 200nA • Intelligent digital peripherals – 1-channel DMA controller dedicated for ADC – Three timers supporting up to 14 PWM channels • One 16-bit advanced timers with deadband support up to 8 PWM channels • One 16-bit general purpose timer with 4 capture/compares • One 16-bit general purpose timer with 2 capture/compares – Windowed watchdog timer – BEEPER generating 1kHz, 2kHz, 4kHz, or 8kHz square wave to drive the external beeper • Enhanced communication interfaces – One UART interface supporting LIN, IrDA, DALI, smart card, Manchester and low-power operation in STANDBY mode – One I2C interface supporting FM+ (1Mbps), SMBus, PMBus, and wakeup from STOP mode – One SPI supporting up to 12Mbps • Clock system – Internal 24MHz oscillator with an accuracy from -2% to +1.2% (SYSOSC) – Internal 32kHz low-frequency oscillator (LFOSC) • Data integrity – Cyclic redundancy checker (CRC-16) • Flexible I/O features – Up to 18 GPIOs – Two 5V-tolerant open-drain IOs • Development support – 2-pin serial wire debug (SWD) • Package options – 20-pin TSSOP (PW) – 20-pin VSSOP (DGS) – 20-pin WQFN (RUK) – 16-pin SOT (DYY) – 8-pin SOT (DDF) – 8-pin WSON (DSG) – 8-pin DSBGA (YCJ) • Family members (also see Device Comparison) – MSPS003F4: 16KB of flash, 1KB of RAM – MSPS003F3: 8KB of flash, 1KB of RAM – MSPM0C1104: 16KB of flash, 1KB of RAM – MSPM0C1103: 8KB of flash, 1KB of RAM • Development kits and software (also see Tools and Software) – LP-MSPM0C1104 LaunchPad™ development kit – MSP Software Development Kit (SDK) 2 Applications • Battery charging and management • Power supplies and power delivery • Personal electronics • Building security and fire safety • Connected peripherals and printers • Grid infrastructure • Smart metering • Communication modules • Medical and healthcare • Lighting #MSPM0C1104S8YCJR #MSPM0C1104 #TexasInstruments #CortexM0Plus #Microcontroller #EmbeddedSystems #LowPowerMCU #IoT #WearableDevices #IndustrialControl #ConsumerElectronics #ADC #UART #SPI #I2C #PWM #TI #ElectronicsDesign #PCBDesign #EmbeddedDevelopment

14 Bit Digital to Analog Converter 4 16-TSSOP The DAC8165IBPW is a quad-channel, precision digital-to-analog converter designed for high-accuracy industrial and instrumentation applications. Manufactured by Texas Instruments, this device integrates four independent voltage-output DAC channels with buffered outputs and a high-resolution serial interface. The component is optimized for systems requiring precise analog signal generation, low noise performance, and stable long-term operation. The device supports a serial peripheral interface compatible with standard SPI communication and allows simultaneous or individual channel updates. Internal precision reference buffering, low offset error, and monotonic output behavior make the DAC8165IBPW suitable for closed-loop control systems, programmable power supplies, automated test equipment, process control, and data acquisition platforms. The DAC operates from a single analog supply and provides rail-to-rail output capability with excellent linearity and low glitch energy. Integrated power-on reset circuitry ensures deterministic startup behavior, while low power consumption enables use in embedded and portable applications. Key Features Quad-channel voltage-output digital-to-analog converter High-resolution precision DAC architecture Buffered voltage outputs with monotonic performance SPI-compatible serial communication interface Low integral and differential nonlinearity Low offset and gain error characteristics Simultaneous update capability for synchronized outputs Internal power-on reset functionality Industrial operating temperature support Low power consumption design Electrical Characteristics Single-supply operation Precision voltage output architecture Fast settling time for dynamic signal applications Low output noise and glitch impulse High DC accuracy and long-term stability Buffered outputs capable of direct system interfacing Package Information Package type: TSSOP Surface-mount configuration Compact footprint suitable for dense PCB layouts Typical Applications Industrial automation Process control systems Programmable logic controllers Data acquisition systems Automated test equipment Precision instrumentation Medical instrumentation Signal generation and calibration systems #commonpartslibrary #integratedcircuit #analog #digital #converter

Voltage Level Translator Bidirectional 1 Circuit 2 Channel 26Mbps 8-XSON (1.35x1) The TCA39416DTWR is a high-performance LED driver and multiplexer IC designed for precise control of multi-channel lighting applications. It integrates constant-current drivers, digital dimming capability, and multiplexing functionality to efficiently manage a large array of LEDs in industrial, automotive, display, and general-purpose lighting systems. The device supports high-speed operation and flexible channel configuration, ensuring uniform brightness control, low electromagnetic interference, and robust performance in space-constrained designs. Its compact surface-mount package and integrated control features make it ideal for embedded lighting solutions requiring reliable, accurate, and scalable LED management. Engineering Specifications Manufacturer: Texas Instruments Part Number: TCA39416DTWR Device Type: LED Driver and Multiplexer IC Channel Count: Multi-Channel LED Control Driver Type: Constant-Current LED Driver Dimming Control: Digital PWM Dimming Supported Multiplexing: Integrated Multiplexer Functionality Input Interface: Digital Control Inputs Output Configuration: Sinking LED Channels Supply Voltage Range: Wide Operating Range Switching Frequency: High-Speed LED Operation Thermal Management: Efficient Power Dissipation Design Package Type: TSSOP Surface-Mount Package Mounting Style: Surface Mount Operating Temperature Range: Industrial Grade RoHS Compliant: Yes Applications: Industrial LED Lighting, Automotive Light Arrays, Display Backlighting, Status Indicators, Embedded LED Systems, Digital Signage, Instrumentation Panels, Multi-Channel LED Control Key Features Multi-channel constant-current LED drivers Integrated digital dimming via PWM control Built-in multiplexing for efficient channel management Compact surface-mount package for PCB integration High-speed operation for flicker-free lighting Low power consumption and thermal optimization Reliable performance in industrial and automotive environments Uniform brightness control across channels Flexible configuration for scalable LED arrays Designed for embedded lighting and display applications #TCA39416DTWR #TexasInstruments #LEDDriver #MultiplexerIC #MultiChannelLED #PWMDimming #EmbeddedLighting #IndustrialElectronics #AutomotiveLighting #DisplayBacklight #LEDControl #SurfaceMountIC #ElectronicComponents #PCBDesign #LEDArray #HighSpeedLED #IndustrialGrade #SignalControl #PowerEfficient #LightingElectronics

10Bit to 16Bit Programmable Angular Magnetic Encoder SMD 16-Pin TSSOP #commonpartslibrary #sensor #magnetic #encoder

High-Voltage SPI Digital Potentiometer – Single-channel 8-bit digital potentiometer for programmable gain control, industrial automation, instrumentation, audio equipment, sensor calibration, power supplies, and embedded analog signal conditioning. Features 50 kΩ nominal resistance with 256 wiper positions (8-bit resolution), a linear taper, and an SPI serial interface for precise digital control. Supports separate digital and analog supply rails, with a digital supply of 1.8 V to 5.5 V and an analog supply up to 36 V (10 V to 36 V single supply or ±5 V to ±18 V dual supply), making it suitable for high-voltage analog applications. Includes 145 Ω typical wiper resistance, 100 ppm/°C temperature coefficient, volatile memory, shutdown capability, and AEC-Q100 qualification for high-reliability environments. Operates over a −40°C to +125°C temperature range and is housed in a 14-pin TSSOP package. #Microchip #MCP41HV51503EST #MCP41HV51 #DigitalPotentiometer #SPIPotentiometer #ProgrammableResistor #HighVoltage #AnalogControl #SignalConditioning #IndustrialElectronics #AECQ100 #EmbeddedSystems

4-Bit Unidirectional Voltage-Level Translator – Four-channel fixed-direction voltage-level translator for logic-level shifting between mixed-voltage digital interfaces. Operates with independent VCCA and VCCB supplies from 1.08 V to 5.5 V, supports data rates up to 200 Mbps, and features Schmitt-trigger inputs for improved noise immunity. Provides 3-state outputs (OE control), push-pull output drivers, partial power-down support (Ioff), and is 5.5 V tolerant on the I/O side when powered appropriately. Specified for operation over a −40°C to +125°C temperature range and housed in a 14-pin TSSOP package. #TexasInstruments #TXU0304 #TXU0304PWR #LevelTranslator #VoltageTranslator #LogicLevelShifter #4BitTranslator #SchmittTrigger #TriStateOutput #DigitalLogic #TSSOP14 #EmbeddedSystems

Three-channel three-input 1.1V-to-3.6V AND gates with 24mA drive strength | PW | 14 | -40 to 125 SN74LVC11APWR is a triple 3-input positive-AND gate designed to perform independent three-input AND logic functions. It operates from a 1.65 V to 3.6 V supply, features 5.5 V tolerant inputs for mixed-voltage interfacing, and provides balanced propagation delay and output drive. The device supports up to ±24 mA output drive at 3.3 V, incorporates Ioff circuitry for partial-power-down operation, and is housed in a 14-pin TSSOP (PW) package. #TexasInstruments #SN74LVC11APWR #LogicIC #ANDGate #TripleANDGate #LVCLogic #DigitalLogic #5Vtolerant #TSSOP14 #PCBComponents

1-Bit Bidirectional Voltage-Level Translator in TSSOP Package With Auto Direction Sensing and ±15-kV ESD Protection, DSBGA-6 bidirectional voltage level translator SOT?23?6*

Triple 2:1 SPDT Precision Analog Multiplexer/Switch – Three-channel Single-Pole Double-Throw (SPDT) analog multiplexer/switch for signal routing, data acquisition systems, industrial automation, instrumentation, audio/video switching, medical electronics, and embedded analog applications. Operates from a single 5 V to 24 V supply or dual ±2.5 V to ±12 V supplies, with 1.8 V-compatible logic inputs for direct interfacing with modern microcontrollers and FPGAs. Features 240 Ω maximum on-resistance, 2 Ω typical channel-to-channel matching, 850 MHz bandwidth, 110 ns maximum turn-on time, 85 ns typical turn-off time, 3 pF off-capacitance, and −90 dB crosstalk at 1 MHz for high signal integrity. Includes break-before-make switching, rail-to-rail analog signal handling, low charge injection, and low leakage current, making it suitable for precision analog signal multiplexing. Specified for operation over a −55°C to +125°C temperature range and housed in a 16-pin TSSOP surface-mount package. #TexasInstruments #TMUX4053PWR #TMUX4053 #AnalogSwitch #AnalogMultiplexer #SPDT #SignalRouting #DataAcquisition #Instrumentation #IndustrialElectronics #TSSOP16 #EmbeddedSystems

16-Bit Delta-Sigma Analog-to-Digital Converter (ADC) – Precision ADC with integrated programmable gain amplifier (PGA), voltage reference, two programmable current sources, oscillator, temperature sensor, and SPI interface. The Texas Instruments ADS1120IPWR supports two differential or four single-ended inputs, 16-bit resolution, and data rates up to 2 kSPS. It operates from a 2.3 V to 5.5 V supply, with programmable gain from 1 to 128 V/V. The device provides 50/60 Hz rejection at 20 SPS and is housed in a 16-pin TSSOP package, operating from −40°C to +125°C. #TexasInstruments #ADS1120 #ADS1120IPWR #ADC #DeltaSigmaADC #16BitADC #PGA #SPI #DataAcquisition #SensorInterface #EmbeddedSystems

4 Circuit IC Switch 2:1 6.2Ohm 20-TSSOP Quad SPDT Analog Switch — provides four independently controlled single-pole double-throw (SPDT) switches with bidirectional signal paths and 1.8 V-compatible logic inputs. It operates from 4.5 V to 36 V single supply or ±4.5 V to ±18 V dual supplies, with 3.6 Ω typical on-resistance, up to 400 mA continuous channel current, and –40°C to +125°C operating temperature. Available in a 20-pin TSSOP (PW) package. #TexasInstruments #TMUX6234PWR #AnalogSwitch #SPDT #Multiplexer #SignalSwitch #TSSOP

16-channel 12-bit PWM Fm+ I2C-bus LED controller RGBA TSSOP PWM LED driver I2C TSSOP TSSOP*4.4x9.7mm*P0.65mm*

SOP65P640X120-20N STM32F042F6P6 http://uk.rs-online.com/web/p/products/8607501P 32-Bit MCU 32K Flash USB2.0 CAN TSSOP20 STMicroelectronics STM32F042F6P6, 32bit ARM Cortex M0 Microcontroller, 48MHz, 32 kB Flash, 20-Pin TSSOP 8607501P 1.2mm STMicroelectronics 511-STM32F042F6P6 https://www.mouser.com/Search/Refine.aspx?Keyword=511-STM32F042F6P6