MAX-M10 RF Receiver BeiDou, Galileo, GLONASS, GPS, GNSS 1.561GHz, 1.575GHz, 1.602GHz -167dBm 921.6kbps Not Included Module The MAX-M10S-00B is a professional-grade, ultra-low-power GNSS positioning module from u-blox based on the u-blox M10 platform. It is designed for battery-powered applications such as asset trackers, wearables, IoT devices, and navigation systems. The module supports simultaneous reception of multiple GNSS constellations, providing high positioning availability, fast acquisition times, and excellent sensitivity even in challenging urban or weak-signal environments. It integrates a TCXO, LNA, and SAW filter to improve RF performance while maintaining very low power consumption. Key Features Multi-constellation GNSS receiver: GPS Galileo GLONASS BeiDou QZSS SBAS support (WAAS, EGNOS, MSAS, GAGAN) Concurrent tracking of up to four GNSS constellations for improved position availability and accuracy. Ultra-low power consumption: Approximately 25 mW in continuous tracking mode, making it ideal for battery-powered devices. High RF sensitivity: Tracking sensitivity up to −167 dBm for reliable operation in weak-signal conditions. High positioning accuracy: Typical position accuracy of approximately 1.5 m CEP under suitable conditions. Navigation update rate: Up to 10 Hz for responsive tracking applications. Integrated RF front-end: Built-in LNA (Low Noise Amplifier) Built-in SAW filter Integrated TCXO for stable operation. Supports Assisted GNSS services: AssistNow Online AssistNow Offline AssistNow Autonomous CloudLocate support for low-power IoT positioning. Communication interfaces: UART I²C NMEA and UBX protocols supported. Wide operating temperature range: −40°C to +85°C. Supply voltage: 1.76 V to 3.6 V. Typical Applications Asset tracking devices Wearable electronics Fleet management systems Industrial IoT Smart meters Drone and robotics navigation Personal navigation devices Timing and synchronization systems Package Information Package Type: Surface-mount LCC module Dimensions: 9.7 mm × 10.1 mm × 2.5 mm (typical module size) #Commonpartslibrary #RF #Wireless #RFreceivers #MAXM10S #uBlox #GNSS #GPS #Galileo #GLONASS #BeiDou #QZSS #NavigationModule #GNSSModule #GPSTracking #AssetTracking #IoT #IndustrialIoT #WearableTech #FleetManagement #DroneNavigation #EmbeddedSystems #ElectronicsDesign #PCBDesign #HardwareEngineering #LowPowerDesign #LocationTracking #Geolocation #RFDesign #LNA #SMTModule

GNSS Multi-Constellation Embedded Chip Antenna – Surface-mount passive GNSS chip antenna optimized for GPS, GLONASS, Galileo, BeiDou, asset tracking, navigation systems, drones, IoT devices, telematics, and embedded positioning applications. Covers the 1560 MHz to 1602 MHz GNSS frequency band with a 1.575 GHz center frequency, 50 Ω impedance, 3 W maximum input power, and VSWR ≤ 2:1 for efficient satellite signal reception. Features a compact 10 × 10 × 1 mm ceramic SMD package, linear polarization, embedded PCB mounting, and peak gain up to 3.5 dBi, making it suitable for space-constrained wireless designs. Designed for operation over a −40°C to +85°C temperature range and compatible with GPS, GLONASS, Galileo, and BeiDou satellite navigation systems. #TEConnectivity #21189001 #GNSSAntenna #ChipAntenna #GPS #GLONASS #Galileo #BeiDou #EmbeddedAntenna #Navigation #IoT #RFDesign #EmbeddedSystems

Mini 2.45 GHz Antenna The 2450AT18A100E is a high-frequency ceramic SMT antenna featuring a small 3.2 mm × 1.6 mm × 1.3 mm package, optimized for space-constrained RF designs. It operates from 2400 MHz to 2500 MHz with a 50 Ω impedance and provides a compact alternative to traditional PCB trace antennas while maintaining reliable RF performance. Key Features Operating Frequency: 2400 MHz – 2500 MHz (2.4 GHz ISM Band) Center Frequency: 2450 MHz Antenna Type: Mini Ceramic Chip Antenna / SMT RF Antenna Package Size: 3.2 mm × 1.6 mm × 1.3 mm Impedance: 50 Ω Peak Gain: Approximately +0.5 dBi (typical) Average Radiation Efficiency: Approximately 76% (based on Johanson evaluation board) Maximum Input Power: 2 W continuous wave (CW) Operating Temperature Range: -40 °C to +125 °C Mounting Type: Surface Mount Technology (SMT) Applications: Bluetooth / BLE devices Wi-Fi 2.4 GHz modules Zigbee / IEEE 802.15.4 systems IoT sensors and embedded wireless products #2450AT18A100E #JohansonTechnology #ChipAntenna #SMTAntenna #RFDesign #2GHzAntenna #Bluetooth #WiFi #Zigbee #IoT #WirelessCommunication #EmbeddedSystems #PCBDesign #RFAntenna #Antena #Chip #SurfaceMount

The RFFC5072 is a highly integrated wideband RF frequency conversion IC that combines a fractional-N PLL synthesizer, low phase-noise VCO, and a high-linearity RF mixer in a single device. It is designed for wireless infrastructure, software-defined radio (SDR), test equipment, military communications, and broadband frequency conversion applications. The device can generate local oscillator (LO) frequencies from 85 MHz to 4.2 GHz and perform frequency conversion for RF signals up to 6 GHz while maintaining excellent phase noise and spurious performance. Features  85MHz to 4200MHz LO Frequency Range  Fractional-N Synthesizer with Very Low Spurious Levels  Typical Step Size 1.5Hz  Fully Integrated Low Phase Noise VCO and LO Buffers  Integrated Phase Noise • 0.18° rms at 1GHz • 0.50° rms at 3GHz  High Linearity RF Mixer(s)  30MHz to 6000MHz Mixer Frequency Range  Input IP3 +23dBm  Mixer Bias Adjustable for Low Power Operation  Full Duplex Mode (RFFC5071)  2.7V to 3.3V Power Supply  Low Current Consumption  3- or 4-Wire Serial Interface Applications  Wideband Radios  Distributed Antenna Systems  Diversity Receivers  Software Defined Radios  Frequency Band Shifters  Point-to-Point Radios  WiMax/LTE Infrastructure  Satellite Communications  Wideband Jammers #RFFC5072 #Qorvo #RFMixer #FrequencySynthesizer #PLL #VCO #WidebandRF #FrequencyConverter #SDR #WirelessInfrastructure #RFDesign #MicrowaveEngineering #Telecommunications #EmbeddedSystems #ElectronicsDesign #RFIC #SignalProcessing #HardwareEngineering

RF IC Synthesizer, VCO VSAT 7.3GHz ~ 14.6GHz SPI Interface 48-LGA (7x7) The ADF5611 allows implementation of fractional-N or integer-N phase-locked loop (PLL) frequency synthesizers when used with an external loop filter and an external reference source. The wideband microwave voltage controlled oscillator (VCO) design permits frequency operation from 7300MHz to 14,600MHz at a single RF output. A series of frequency dividers with a differential frequency output allows operation from 57MHz to 14,600MHz. Analog and digital power supplies for the PLL circuitry range from 3.15V to 3.45V, and the VCO supplies are between 4.75V and 5.25V. The ADF5611 has an integrated VCO with a fundamental frequency of 3650MHz to 7300MHz. These frequencies are internally doubled and routed to the RFOUT pin. An additional differential output allows the doubled VCO frequency to be divided by 1, 2, 4, 8, 16, 32, 64, or 128, allowing the user to generate RF output frequencies as low as 57MHz. A simple 3- or 4-wire serial port interface (SPI) provides control of all on-chip registers. To conserve power, this divider block can be disabled when not needed through the SPI. Likewise, the output power for both the single-ended output and the differential output are programmable. The integrated phase detector and Δ-Σ modulator, capable of operating at up to 100MHz, permit wide loop bandwidths and fast frequency tuning with a typical spurious level of −105dBc. With a VCO open-loop phase noise at an 100kHz offset from −115dBc/Hz at a 7.3GHz RFOUT to −109dBc/Hz at a 14.6GHz RFOUT, the ADF5611 is equipped to minimize blocker effects and to improve receiver sensitivity and transmitter spectral purity. The low phase noise floor eliminates any contribution to modulator and mixer noise floor in transmitter applications. ► RFOUT frequency range: 7300MHz to 14,600MHz ► PDIV_OUT and NDIV_OUT frequency range: 57MHz to 14,600MHz ► Fractional-N synthesizer and integer-N synthesizer modes ► Typical PFD spurious: <−105dBc ► Integrated RMS jitter at 1kHz to 100MHz integration bandwidth: <40fs ► Normalized inband phase noise floor FOM ► Integer mode: −232dBc/Hz ► Fractional mode: −229dBc/Hz ► Maintains frequency lock over −40°C to +85°C (lock and leave) ► Low phase noise VCO ► −115dBc/Hz typical at 100kHz (7.3GHz) ► −114dBc/Hz typical at 100kHz (10GHz) ► −109dBc/Hz typical at 100kHz (14.6GHz) ► RFOUT power (typical): 6dBm ► Programmable divide by 1, 2, 4, 8, 16, 32, 64, or 128 output ► Programmable output power level ► Typical power dissipation: 1W ► 48-terminal, 7 mm × 7 mm LGA package: 49 mm2 #ADF5611BCCZ #ADF5611 #FrequencySynthesizer #PLL #MicrowaveSynthesizer #RFIC #LowPhaseNoise #VCO #WirelessInfrastructure #SatelliteCommunication #MicrowaveRadio #TestAndMeasurement #AnalogDevices #RFDesign #ClockGeneration

Maxim Integrated PLL Frequency Synthesizer Single 23.5MHz to 6000MHz 32-Pin TQFN EP QFN-32 Maxim None MAX2871ETJ+ Unavailable Maxim Integrated MAX2871 ultra-wideband fractional-N / integer-N PLL frequency synthesizer with integrated VCOs, capable of generating RF frequencies from 23.5MHz to 6.0GHz. Features programmable output dividers (1/2/4/8/16/32/64/128), dual differential RF outputs with programmable output power from -1dBm to +8dBm, low phase noise performance, phase frequency detector up to 140MHz, reference frequency up to 210MHz, fast lock and cycle-slip reduction, automatic/manual VCO selection, on-chip temperature sensor with 7-bit ADC, 4-wire SPI-compatible serial interface, and operation from -40°C to +85°C. Suitable for wireless infrastructure, clock generation, microwave radios, RF signal generation, and test & measurement equipment. MAX2871 Search Keywords: MAX2871, Maxim MAX2871, Analog Devices MAX2871, PLL synthesizer, RF synthesizer, fractional N synthesizer, integer N synthesizer, 6GHz frequency synthesizer, RF signal generator IC, integrated VCO synthesizer, microwave synthesizer, SPI frequency synthesizer, dual output PLL, clock generation IC, wireless infrastructure synthesizer Hashtags: #MAX2871 #MaximIntegrated #AnalogDevices #PLLSynthesizer #FrequencySynthesizer #RFSynthesizer #FractionalNPLL #IntegerNPLL #IntegratedVCO #RFSignalGenerator #MicrowaveRadio #ClockGeneration #WirelessInfrastructure #SPIInterface #TestAndMeasurement #RFDesign #RFIC #PhaseLockedLoop

ADQ-22+ is a surface-mount 2-way RF power splitter/combiner from Mini-Circuits designed for broadband signal distribution and combining applications. It operates over a frequency range of 2 MHz to 500 MHz, providing equal power division with low insertion loss, excellent amplitude balance, and phase balance characteristics. The device features a compact SMT package optimized for automated PCB assembly and RF circuit integration. Typical applications include RF signal distribution, communication systems, instrumentation, microwave links, test equipment, receivers, transmitters, antenna systems, and broadband signal processing circuits where low loss and accurate signal splitting or combining are required. Mini-Circuits ADQ-22+ ADQ-22+, ADQ22+, Mini-Circuits ADQ-22+, RF power splitter, RF power combiner, 2-way power splitter, 2-way power divider, RF signal splitter, broadband power divider, RF distribution network, SMT RF splitter, RF combiner, microwave power divider, communication system RF component, 2MHz to 500MHz splitter, RF signal distribution, test equipment RF splitter, antenna signal splitter, Mini-Circuits power divider Hashtags: #ADQ22 #MiniCircuits #PowerSplitter #PowerDivider #PowerCombiner #RF #RFDesign #MicrowaveEngineering #Telecommunications #SignalDistribution #RFComponents #BroadbandRF #AntennaSystems #TestEquipment #WirelessSystems #Electronics #ElectronicComponents #PCBDesign #RFEngineering #SurfaceMountSignal Conditioning PWR SPLTR CMBD / SURF MT/ RoHS

CAP SAFETY 2.2nF ±20% 400V 250V TH The DCF222M34Y5UQ6BL7A0 is a multilayer ceramic capacitor manufactured for general-purpose electronic filtering, bypassing, and decoupling applications. This surface-mount passive component is designed to provide stable capacitance performance in compact electronic assemblies while supporting high-density PCB layouts and automated manufacturing processes. The capacitor utilizes ceramic dielectric technology to achieve low impedance and reliable high-frequency performance. It is commonly used in power supply filtering, signal coupling, noise suppression, RF circuits, embedded systems, industrial electronics, and consumer devices. Its compact footprint and stable electrical behavior make it suitable for modern digital and analog circuit designs requiring efficient decoupling and transient response characteristics. Engineering Specification Device Type Multilayer ceramic capacitor Capacitor Technology Ceramic dielectric multilayer structure Mounting Style Surface mount technology Electrical Characteristics Stable capacitance performance for filtering and bypass applications Dielectric Characteristics Designed for general-purpose signal and power conditioning applications Frequency Performance Low impedance behavior suitable for high-frequency operation Thermal Characteristics Stable operation across standard electronic operating temperatures Mechanical Characteristics Compact SMT package optimized for automated PCB assembly Reliability Features High insulation resistance and long operational lifetime Construction Monolithic multilayer ceramic structure Applications Power supply decoupling Signal filtering Noise suppression RF circuitry Embedded systems Industrial electronics Consumer devices Communication equipment Analog and digital circuit stabilization Manufacturer Commonly associated with Murata-style MLCC component series #commonpartslibrary #ceramiccapacitor #mlcc #passivecomponents #surfaceountcomponents #powerelectronics #signalfiltering #decouplingcapacitor #electronicsdesign #embeddedhardware #analogdesign #digitalelectronics #rfdesign #industrialelectronics

IC RF TxRx + MCU Bluetooth Bluetooth v5.0 2.4GHz 32-VFQFN Exposed Pad nRF52810-QCAA-R is a multiprotocol ultra-low-power wireless System-on-Chip from Nordic Semiconductor designed for Bluetooth Low Energy and proprietary wireless communication applications. The device integrates a high-performance ARM Cortex-M processor, radio transceiver, memory resources, and peripheral interfaces into a compact package optimized for low-power embedded systems and IoT devices. This SoC supports reliable wireless connectivity with low energy consumption, making it suitable for wearable electronics, wireless sensors, smart home devices, industrial monitoring systems, and battery-powered portable applications. The integrated radio architecture provides stable RF performance with support for advanced wireless features, secure communication, and efficient coexistence in crowded RF environments. The nRF52810-QCAA-R includes multiple GPIOs, serial communication peripherals, timers, PWM functionality, analog interfaces, and low-power operating modes that simplify embedded hardware design and firmware development. Its compact package and optimized power profile make it ideal for space-constrained and energy-sensitive wireless applications. #commonpartslibrary #nordicsemiconductor #bluetoothlowenergy #wirelesssoc #iotdevices #embeddedhardware #rfdesign #lowpowerdesign #wearableelectronics #wirelesscommunication

Small and thin surface-mount crystal units NX1612SA-32MHZ-STD-CIS-3 is a compact surface-mount quartz crystal oscillator designed for stable clock generation in embedded electronic systems and wireless communication devices. Manufactured in a miniature ceramic package, this crystal provides precise frequency control with low phase noise and high frequency stability, making it suitable for microcontrollers, RF modules, IoT devices, and portable electronics. The device operates at a nominal frequency of thirty-two megahertz and is optimized for low power consumption and reliable startup characteristics. Its compact footprint enables integration into high-density PCB layouts while maintaining strong resistance to environmental stress and mechanical vibration. The crystal is compatible with standard oscillator circuits and supports stable operation across industrial temperature ranges. This component is commonly used in timing reference applications, communication systems, sensor modules, wearable devices, and battery-powered embedded platforms requiring accurate and stable clock signals. #commonpartslibrary #crystaloscillator #timingdevice #frequencycontrol #embeddedhardware #wirelesssystems #rfdesign #iotdevices #electronicscomponents #surfacemountdevice