Linear Voltage Regulator IC Positive Fixed 1 Output 600mA SOT-25 3.3V LDO AP2112K-3.3 The AP2112K-3.3TRG1 is a low dropout (LDO) linear voltage regulator designed to provide a stable 3.3V output from a higher input voltage. It is optimized for low noise, high power supply rejection ratio (PSRR), and low quiescent current, making it suitable for battery-powered and noise-sensitive applications. The device features current limiting and thermal shutdown protection, ensuring reliable operation under fault conditions. It is commonly used in portable electronics, RF modules, microcontroller power supplies, and other low-power systems. Key Features Fixed output voltage: 3.3V Output current: up to 600 mA Low dropout voltage: ~250 mV at 300 mA load High PSRR: up to 70 dB at 1 kHz Low quiescent current: typically 55 µA Stable with low ESR ceramic capacitors Built-in overcurrent protection Thermal shutdown protection Fast transient response Absolute Maximum Ratings Input Voltage (VIN): up to 6.5 V Output Current: Internally limited Operating Junction Temperature: -40°C to +125°C Storage Temperature: -65°C to +150°C Electrical Characteristics (Typical values unless otherwise specified) Output Voltage Accuracy: ±2% Dropout Voltage: 250 mV @ 300 mA 400 mV @ 600 mA Line Regulation: 0.05%/V Load Regulation: 0.2% Quiescent Current: 55 µA Shutdown Current: <1 µA PSRR: 70 dB @ 1 kHz 45 dB @ 10 kHz Pin Configuration (SOT-23-5 / SC-70-5) VIN – Input voltage GND – Ground EN – Enable (active high) NC – No connection VOUT – Regulated output (3.3V) Package Information Package Type: SOT-23-5 (TRG1 suffix indicates tape & reel) Mounting: Surface mount Small footprint suitable for compact PCB layouts Typical Applications Battery-powered devices Wireless modules (Wi-Fi, Bluetooth, RF) Microcontroller and FPGA power supplies Portable consumer electronics Sensor and analog circuits requiring low noise Compliance & Reliability RoHS compliant Lead-free package Designed for high reliability and long operational life #CommonPartsLibrary #IntegratedCircuit #PowerManagement #LinearRegulator #VoltageRegulator

2 Position Terminal Block Header, Male Pins, Shrouded (4 Side) 0.200" (5.08mm) 90°, Right Angle Through Hole Phoenix Contact MSTBA 2.5/ 2-G-5.08 CAN connector terminal block 2 pin The component is a two-position pluggable terminal block header designed for secure and reliable wire-to-board connections in industrial and embedded electronic systems. It is part of the COMBICON MSTB family, widely used for field wiring applications such as CAN bus, RS485, and power distribution. The device provides a robust interface between PCB circuitry and external wiring, supporting easy installation, maintenance, and replacement through a pluggable connection system. Mechanical Characteristics Number of Positions: 2 Pitch: 5.08 mm Mounting Type: Through-hole PCB mount Orientation: Vertical (straight) Termination Style: Pin header for mating plug connector Housing Material: Polyamide (PA), high-temperature resistant Color: Green Electrical Characteristics Rated Voltage: Up to 250 V Rated Current: Up to 12 A Contact Material: Copper alloy Contact Plating: Tin plated Environmental Characteristics Operating Temperature Range: -40°C to +105°C Flammability Rating: UL94 V-0 Mating and Compatibility Compatible Plug Series: Phoenix Contact MSTB 2,5 series (e.g., 1757019) Connection Method (Plug Side): Screw clamp termination Wire Size Range: Typically accepts 24 AWG to 12 AWG (depending on mating plug) Standards and Compliance RoHS: Compliant UL Recognized: Yes IEC Compliance: Yes Application Notes The component is commonly used in industrial communication systems such as CAN bus networks where a reliable and removable connection is required for CANH and CANL signals. Its 5.08 mm pitch ensures adequate spacing for signal integrity and ease of wiring, while the pluggable design simplifies field servicing and module replacement. #connector #tht #terminalblock

Tactile Switch SPST-NO Top Actuated Through Hole tactile switch 6x6 through hole The B3F-1000 is a compact, through-hole mounted tactile switch designed for momentary input applications. It features a standard 6.0 mm square footprint and is widely used in consumer and industrial electronics for reliable user interface control. Mechanical Characteristics Dimensions (L × W × H): 6.0 mm × 6.0 mm × 3.4 mm Actuator Type: Round Actuator Height: 4.3 mm Mounting Style: Through Hole Mounting Direction: Straight Termination Style: Solder Pin Color: White Electrical Characteristics Switch Function: SPST, Momentary (OFF-(ON)) Contact Rating: 50 mA @ 24 VDC Operating Force: 1 N (~100 gf) Contact Resistance: ≤100 mΩ (typical, refer to datasheet) Insulation Resistance: ≥100 MΩ (typical, refer to datasheet) Environmental Characteristics Operating Temperature Range: -25°C to +70°C RoHS Compliance: Yes Reliability Operating Life: 1,000,000 cycles Packaging Information Factory Pack Quantity: 1500 pcs Unit Weight: 0.008818 oz (~0.25 g) Additional Information Country of Origin: Japan (JP) Illumination: Non-illuminated Ground Terminal: No #commonpartslibrary #switch #tactile #spst

Connector Header Through Hole 4 position 0.100" (2.54mm) UART header 1x4 2.54mm Single-row, through-hole male pin header with 4 positions and 2.54 mm pitch. Designed for board-to-wire or board-to-board interconnect applications such as UART interfaces. Mechanical Specifications Number of Positions: 4 Number of Rows: 1 Pitch: 2.54 mm (0.100") Mounting Style: Through Hole Mounting Angle: Straight (Vertical) Contact Gender: Male (Pin) Termination Type: Solder Pin Housing Material: Polybutylene Terephthalate (PBT) Housing Color: Black Electrical Specifications Current Rating: 4.3 A – 6.3 A (per pin, depending on conditions) Voltage Rating: 450 VAC – 550 VAC Contact Resistance: (Typical for series, not specified exact) Insulation Resistance: (Not specified) Material & Plating Contact Material: Phosphor Bronze Contact Plating: Gold Flammability Rating: UL94 V-0 Environmental & Compliance RoHS Compliance: Yes Country of Origin: USA Packaging Packaging Type: Bulk Factory Pack Quantity: 1 Series Information Series: TSW (Samtec Pin Strip Header Series) Product Type: Headers & Wire Housings Typical Applications UART / Serial communication headers Microcontroller programming interfaces General-purpose 2.54 mm interconnects Prototyping and development boards #commonpartslibrary #connector

USB-C (USB TYPE-C) USB 2.0 Receptacle Connector 24 (16+8 Dummy) Position Surface Mount, Right Angle; Through Hole USB Type-C receptacle 16 pin USB2.0 The USB4215-03-A is a USB Type-C receptacle connector designed for USB 2.0 applications. It features a 16-pin configuration supporting reversible plug orientation with standard USB 2.0 differential data lines and configuration channel (CC) pins. The connector is intended for surface-mount PCB assembly with through-hole shell stakes for enhanced mechanical strength. It is widely used in compact embedded systems for power delivery, charging interfaces, and basic data communication. Key Features USB Type-C receptacle (USB 2.0 compliant) 16 functional pins (no SuperSpeed support) Reversible plug orientation Surface-mount contacts with through-hole shell tabs Compact, low-profile design High insertion cycle durability Suitable for automated assembly Electrical Characteristics Rated Current: VBUS: up to 5.0 A (depending on PCB design and cable) Signal pins: 0.25 A max Rated Voltage: 20 V DC max Contact Resistance: ≤ 40 mΩ Insulation Resistance: ≥ 100 MΩ Dielectric Withstanding Voltage: 100 V AC Mechanical Characteristics Mounting Type: Surface Mount (SMT) with Through-Hole Shield Tabs Number of Positions: 16 Mating Cycles: 10,000 cycles (typical) Insertion Force: 5–20 N Extraction Force: 8–20 N Material Specifications Contacts: Copper Alloy Contact Plating: Gold over Nickel Housing: High-temperature thermoplastic (UL94V-0) Shell: Stainless Steel Environmental Characteristics Operating Temperature Range: -25°C to +85°C Storage Temperature Range: -40°C to +85°C RoHS Compliant: Yes Halogen Free: Yes Pin Configuration (USB 2.0 Type-C) VBUS (Power) GND (Ground) D+ / D− (USB 2.0 differential pair) CC1 / CC2 (Configuration channel) SBU pins (optional/unused in USB 2.0 designs) Applications USB power input (5 V / USB-C PD trigger designs) Embedded systems and development boards Consumer electronics Charging interfaces Low-speed USB communication devices Packaging Tape & Reel for automated pick-and-place assembly Compliance & Standards USB Type-C Specification (USB 2.0 interface) RoHS / REACH compliant UL recognized materials #CommonPartsLibrary #Connector #USB-C

2 Position Wire to Board Terminal Block Horizontal with Board 0.197" (5.00mm) Through Hole screw terminal 2 pin 3.5mm This component is a printed circuit board mounted screw terminal block designed to provide a secure and serviceable wire-to-board connection. It accommodates two conductors and uses a screw clamp mechanism to ensure reliable electrical and mechanical contact. The compact 3.5 mm pitch makes it suitable for space-constrained designs while maintaining adequate creepage and clearance distances for low-voltage applications. The terminal is intended for through-hole mounting and supports field wiring without the need for specialized tools, making it appropriate for industrial control systems, power distribution modules, and general-purpose electronic assemblies. Mechanical Characteristics: The terminal block is constructed with a high-temperature thermoplastic housing that provides mechanical strength and electrical insulation. The housing is typically green in color and designed for side-entry wire insertion. The clamping system uses metal screws and pressure plates to secure stripped wire ends. The component is designed for through-hole PCB mounting with soldered pins providing structural stability. The form factor supports modular placement along the PCB edge for accessible wiring. Electrical Characteristics: The device is designed for low to moderate voltage and current applications typical of signal and power connections in control electronics. Conductive elements are made from metal alloys with appropriate plating to ensure good conductivity and resistance to corrosion. The screw clamp connection provides stable contact resistance under vibration and thermal cycling conditions. Material and Environmental Characteristics: The insulating body is made from flame-retardant thermoplastic material compliant with relevant safety standards. The component is suitable for standard operating temperature ranges encountered in industrial and commercial electronics. Materials are selected to meet common environmental and regulatory requirements such as RoHS compliance. Application Considerations: This terminal block is intended for applications requiring reliable field wiring connections, ease of maintenance, and secure termination. It is commonly used in power supplies, control panels, interface modules, and embedded systems. Proper PCB footprint design and adherence to recommended soldering practices are required to ensure optimal performance and reliability. #CommonPartsLibrary #Connector #Terminal-Block #WR-TBL Series 1377

Bipolar (BJT) Transistor NPN 40V 200 mA 300MHz 625 mW Through Hole TO-92-3 The 2N3904TFR is a general-purpose NPN bipolar junction transistor (BJT) designed for low-power amplification and switching applications. It is widely used in signal processing, small-signal amplification, and digital switching circuits. This transistor offers fast switching speed, low saturation voltage, and reliable performance in a compact surface-mount package, making it suitable for consumer electronics, industrial controls, and embedded systems. Manufacturer Various (commonly ON Semiconductor / onsemi, Diodes Inc., Central Semiconductor) Part Number 2N3904TFR Transistor Type NPN Bipolar Junction Transistor (BJT) Configuration Single Package / Case SOT-23 (TO-236AB) Mounting Style Surface Mount (SMD/SMT) Collector-Emitter Voltage (VCEO) 40 V Collector-Base Voltage (VCBO) 60 V Emitter-Base Voltage (VEBO) 6 V Collector Current (IC) 200 mA (max) Power Dissipation (PD) ~200 mW to 350 mW (package dependent) DC Current Gain (hFE) 100 to 300 (typical, varies with operating conditions) Transition Frequency (fT) ~300 MHz Collector-Emitter Saturation Voltage (VCE(sat)) ~0.2 V (typical at IC = 10 mA, IB = 1 mA) Operating Temperature Range -55°C to +150°C Polarity NPN Packaging Tape & Reel (TFR suffix) RoHS Compliance Compliant #commonpartslibrary #transistor #bjt

Polymeric PTC Resettable Fuse 60V 500 mA Ih Surface Mount 2-SMD 500mA resettable fuse pptc The SMD050F-2 is a surface-mount resettable fuse (PPTC – Polymer Positive Temperature Coefficient) designed to provide overcurrent protection in low-voltage electronic circuits. It operates by increasing its resistance significantly when excessive current flows, thereby limiting current and protecting downstream components. Once the fault condition is removed and the device cools, it automatically resets to its low-resistance state, enabling normal operation without replacement. This component is commonly used in power supply lines, USB ports, battery-powered devices, and general electronic protection applications where space-saving and reliability are important. Key Features Resettable overcurrent protection (self-recovering) Surface-mount package for compact PCB layouts Low resistance in normal operation Fast response to fault conditions Automatic reset after fault removal RoHS compliant and lead-free Electrical Characteristics Hold current: 0.5 A Trip current: 1.0 A (typical) Maximum voltage: 60 V Maximum current: 40 A (fault current rating) Initial resistance: low resistance range suitable for minimal voltage drop Resistance after trip: significantly increased to limit current Thermal Characteristics Operating temperature range: -40°C to +85°C Trip time dependent on applied current and ambient temperature Reset time dependent on cooling conditions Mechanical Characteristics Package type: Surface-mount (SMD) Compact footprint suitable for dense PCB layouts Compatible with standard reflow soldering processes Applications USB and peripheral port protection Power supply and DC line protection Battery pack protection Consumer electronics Industrial control circuits Compliance and Standards RoHS compliant Halogen-free (depending on manufacturer variant) Meets industry standards for resettable fuses #commonpartslibrary #circuitprotection #ptc #fuse

Connector Header Through Hole 5 position 0.100" (2.54mm) SWD header 1x5 2.54mm PinHeader 1x05 2.54mm horizontal The TSW-105-07-G-S is a high-reliability, through-hole, single-row pin header from Samtec’s TSW series. It is designed for board-to-board or wire-to-board interconnections in a wide range of electronic applications. Featuring a standard 2.54 mm pitch and gold-plated contacts, this connector ensures reliable electrical performance, durability, and compatibility with industry-standard mating components. Mechanical Characteristics Connector Type: Pin Header Mounting Type: Through-Hole Number of Positions: 5 Number of Rows: Single Row Pitch: 2.54 mm Orientation: Vertical Termination Style: Solder Contact Shape: Square Post Material and Plating Contact Material: Phosphor Bronze Contact Plating: Gold over Nickel Housing Material: Black Thermoplastic (UL94 V-0 rated) Electrical Characteristics Current Rating: Typically up to 3 A per contact Voltage Rating: Typically up to 500 VAC Contact Resistance: Low contact resistance for reliable signal transmission Insulation Resistance: High insulation resistance Environmental Characteristics Operating Temperature Range: -55°C to +125°C Flammability Rating: UL94 V-0 Applications Board-to-board connections Wire-to-board interfaces Prototyping and development systems Industrial and consumer electronics Compliance and Standards RoHS Compliant Lead-Free #CommonPartsLibrary #Connector #Header #TSW

Fuse Holder 80V 1 Circuit Blade Through Hole General Description The 178.7017.0001 is a PCB-mounted fuse holder designed for cartridge fuses, typically used in power input protection circuits. It provides a secure and reliable method for mounting and replacing fuses in electronic assemblies. This component is commonly used in industrial equipment, power supplies, and consumer electronics where overcurrent protection is required. Key Features Designed for standard cartridge fuses (commonly 5x20 mm format) Through-hole PCB mounting for secure mechanical stability Reliable electrical contact with low resistance Easy fuse replacement and maintenance High-temperature resistant housing material Suitable for mains and low-voltage applications Mechanical Characteristics Mounting Type: Through-Hole (THT) Fuse Size Compatibility: 5 mm x 20 mm Orientation: Vertical PCB mount Housing Material: Thermoplastic (UL94 V-0 rated) Pin Configuration: 2-pin Electrical Characteristics Rated Current: Up to 10 A (depending on fuse used) Rated Voltage: Up to 250 VAC Contact Resistance: Low contact resistance for efficient conduction Insulation Resistance: High insulation resistance Environmental Characteristics Operating Temperature Range: -40°C to +85°C (typical) Storage Temperature Range: -40°C to +85°C Flame Rating: UL94 V-0 compliant Applications Power supply units Industrial control systems Consumer electronics Battery chargers AC mains protection circuits Compliance & Standards RoHS compliant UL recognized materials (depending on manufacturer variant) Notes Ensure compatibility with selected fuse rating and type Observe proper PCB layout spacing for high-voltage applications Follow safety standards when used in mains-powered circuits #commonpartslibrary #circuitprotection #fuseholder

ESP32-S3-MINI-1-N8 is a compact, low-power Wi-Fi and Bluetooth module from Espressif Systems based on the ESP32-S3 SoC. It integrates a dual-core Xtensa LX7 processor, 8 MB flash memory, crystal oscillator, RF matching circuitry, and a PCB antenna in a small SMD package, making it ideal for IoT devices, smart home products, industrial automation, HMI applications, AIoT edge devices, and USB-connected embedded systems. Key Features Dual-core 32-bit Xtensa LX7 CPU Up to 240 MHz operating frequency Includes single-precision floating-point unit (FPU) for enhanced processing performance. Integrated Memory 8 MB Quad SPI Flash (N8 variant) 512 KB SRAM 384 KB ROM 16 KB RTC SRAM. Wireless Connectivity 2.4 GHz Wi-Fi 4 (802.11 b/g/n) Data rates up to 150 Mbps Bluetooth 5 LE with Bluetooth Mesh support Simultaneous Wi-Fi and Bluetooth operation through an integrated coexistence mechanism. Rich Peripheral Set Up to 39 GPIOs USB 2.0 OTG USB Serial/JTAG SPI, I²C, I²S, UART PWM, MCPWM SDIO Host ADC Touch sensing Temperature sensor TWAI® (CAN 2.0 compatible) Timers and watchdogs. Integrated Components On-board 40 MHz crystal oscillator PCB antenna RF matching network Compact certified module design. Operating Conditions Supply voltage: 3.0 V to 3.6 V Operating temperature: −40°C to +85°C. Compliance RoHS and REACH compliant RF-certified module for simplified product development. #RF_transceiver #Module #Esp32

Polymeric PTC Resettable Fuse 6V 500 mA Ih Surface Mount 0603 (1608 Metric), Concave polyfuse 500mA 0603 The 0603L050YR is a surface-mount resettable fuse based on polymeric positive temperature coefficient technology, designed to provide overcurrent protection in compact electronic circuits. Under normal operating conditions, the device exhibits low resistance and allows current to pass with minimal power loss. When exposed to an overcurrent condition, the device transitions to a high-resistance state, effectively limiting the current and protecting downstream components. Once the fault condition is removed and power is cycled or the device cools, the fuse automatically resets to its original low-resistance state. This component is optimized for space-constrained applications requiring reliable, resettable protection, such as portable electronics, battery-powered systems, and low-voltage signal lines. Its small form factor enables integration into dense PCB layouts while maintaining compliance with industry safety standards for overcurrent protection. Package and Mounting: Surface-mount device in standard 0603 footprint, compatible with automated assembly processes including reflow soldering. Electrical Characteristics: The device is designed to maintain normal operation at a defined hold current level and transition to a protective state when the current exceeds its trip threshold. It operates within low-voltage circuits and provides fast response to fault conditions while minimizing nuisance tripping under typical load variations. Functional Behavior: The fuse operates by increasing resistance sharply in response to thermal energy generated by excess current. This behavior reduces current flow and limits fault energy. After removal of the overcurrent condition, the device gradually returns to its conductive state, enabling repeated use without replacement. Applications: Suitable for use in power lines, battery packs, USB interfaces, consumer electronics, and other low-voltage systems where resettable overcurrent protection is required. Compliance and Reliability: Designed to meet relevant safety and environmental standards for electronic components, ensuring stable performance across specified operating conditions and long-term reliability in field applications. #commonpartslibrary #fuse #Circuit-Protection #PTC #ptc #polymeric

4 Position Wire to Board Terminal Block Horizontal with Board 0.138" (3.50mm) Through Hole The TE Connectivity 284391-4 is a through-hole mounted PCB terminal block designed for wire-to-board power and signal connections in industrial and electronic control applications. The component belongs to the Buchanan series and features a side-entry wire interface with a horizontal mating orientation. The terminal block supports secure screw-clamp wire termination and is intended for reliable field wiring in low-voltage systems. The connector provides four positions with a 3.5 mm pitch and supports wire sizes from 14 AWG to 30 AWG. The housing is manufactured from polyamide PA66 (Nylon 6/6) with a UL94 V-0 flammability rating. Conductive elements are constructed from brass with tin-plated contacts and nickel-plated clamp and screw components to ensure corrosion resistance and electrical reliability. The device is rated for up to 12 A current and 300 V operation and is suitable for PCB-mounted applications requiring compact, stackable terminal connections. The terminal block includes side interlocking capability for modular multi-position expansion. Engineering Specification Component Type: PCB Terminal Block Manufacturer: TE Connectivity AMP Connectors Series: Buchanan Manufacturer Part Number: 284391-4 Connector Configuration: Wire-to-Board Mounting Type: Through Hole Wire Entry Orientation: Horizontal / Side Entry Number of Positions: 4 Number of Levels: Single Level Pitch: 3.50 mm Wire Termination Method: Screw Rising Cage Clamp Supported Wire Gauge: 14 AWG to 30 AWG Screw Thread Size: M3 Recommended Screw Torque: 0.25 Nm (2.2 lb-in) Rated Current: 12 A Rated Voltage: 300 V AC Housing Material: Polyamide PA66 (Nylon 6/6) Housing Color: Green Flammability Rating: UL94 V-0 Contact Material: Brass Contact Plating: Tin Clamp Material: Brass with Nickel Plating Screw Material: Brass with Nickel Plating Feature Set: Side Interlocking Capability Compliance: RoHS Compliant Mounting Orientation: PCB Straight Mount The component shall be used in applications requiring secure PCB-mounted terminal connections with moderate current handling capability and compact spacing. Typical applications include industrial control systems, embedded electronics, instrumentation, automation interfaces, and low-voltage power distribution assemblies. #commonpartslibrary #connector #header

Bluetooth, WiFi 802.11b/g/n/ax, Bluetooth v5.4 Transceiver Module 2.4GHz Integrated, Chip Surface Mount Silicon Labs SiWG917 module is our lowest power Wi-Fi 6 plus Bluetooth LE 5.4, ideal for ultra-low power IoT wireless devices using Wi-Fi®, Bluetooth, Matter, and IP networking for secure cloud connectivity. It is optimal for developing battery operated devices that need long battery life. SiWG917 module includes an ultra-low power Wi-Fi 6 plus Bluetooth Low Energy (LE) 5.4 wireless CPU subsystem, and an integrated micro-controller (MCU) application subsystem, security, peripherals and power management subsystem all in a single 16 x 21.1 x 2.3 mm package. The wireless subsystem consists of a multi-threaded Network Wireless Processor (NWP) running up to 160 MHz, baseband digital signal processing, analog front end, 2.4 GHz RF transceiver and integrated power amplifier. The application subsystem consists of an ARM® Cortex®-M4 running up to 180 MHz, embedded SRAM, flash, ultra-low power sensor hub, and matrix vector processor. The ARM® Cortex®-M4 is dedicated for peripheral and application-related processing, while the NWP runs the wireless and networking stacks on independent threads, thus providing a fully integrated solution that is ready for a wide range of embedded wireless IoT applications. The modules come with modular radio type approvals for various countries, including USA (FCC), Canada (IC/ISED) and Japan (MIC), and are in compliance with the relevant EN standards (including EN 300 328 v2.2.2) for the conformity with the directives and regulations in EU and UK. KEY FEATURES • Wi-Fi 6 Single Band 2.4 GHz 20 MHz 1x1 stream IEEE 802.11 b/g/n/ax • Bluetooth LE 5.4 • Single chip Matter Over Wi-Fi Solution • ARM® Cortex® M4 Processor with FPU subsystem up to 180 MHz with rich set of Digital and Analog Peripherals. • Wi-Fi 6 Benefits: TWT for improved efficiency and longer battery life, MUMIMO/OFDMA for Higher Throughput, network capacity and low latency • Best in Class Device and Wireless Security • WLAN Tx power up to +17.5 dBm with integrated PA • Bluetooth LE Tx power up to +17 dBm with integrated PA • WLAN Rx sensitivity as low as -95.5 dBm • Wi-Fi 4 Standby Associated mode current: 71 μA @ 1-second listen interval • Embedded Flash option up to 8 MB/ optional external Flash up to 16 MB • Embedded PSRAM option up to 2 MB/ optional external PSRAM option up to 16 MB • Ultra-low power sensor hub peripherals • Matrix Vector Processor (MVP) • Embedded Wi-Fi, Bluetooth LE, Matter, and networking stacks supporting wireless coexistence • Three software-configurable MCU application memory options for sharing the RAM between the wireless, system, and application (192/256/320 KB) • Operating temperature: -40 to +85 ºC • Operating supply range: 3.0 to 3.63 V • Supply voltage for GPIOs: 1.71 to 3.63 V #WiFi6 #BluetoothLE54 #IoTModule #WirelessSoC #SiliconLabs #EmbeddedSystems #SmartHome #IndustrialIoT #LowPowerDesign #RFModule #ConnectedDevices #EdgeComputing #MatterReady #PCBDesign #ElectronicsEngineering

1/1 Transceiver Half CANbus 8-SOIC The SN65HVD230DR is a high-speed Controller Area Network (CAN) transceiver designed to interface a CAN protocol controller with the physical two-wire CAN bus. It operates as a differential line driver and receiver, translating logic-level signals into robust bus-level signals suitable for automotive, industrial, and distributed control applications. The device is optimized for reliable communication in electrically noisy environments and supports low-power operation, making it suitable for systems requiring energy efficiency and extended operational stability. This transceiver conforms to widely adopted CAN physical layer standards and is intended for use in systems requiring high data integrity, fault tolerance, and electromagnetic compatibility. It integrates protection features and supports standby functionality to reduce system power consumption when communication is inactive. Functional Overview The device provides bidirectional signal conversion between a CAN controller and the differential CAN bus lines. It features a transmit data input and a receive data output, enabling full-duplex communication at the protocol level. The driver stage generates differential output signals on the bus, while the receiver stage detects and translates bus signals back into logic-level data. An internal control mechanism allows the device to enter a low-power standby mode, reducing current consumption when active communication is not required. The transceiver includes slope control capability to manage signal edge rates, which helps minimize electromagnetic interference and improves signal integrity across the network. Electrical Characteristics The transceiver operates from a single low-voltage supply and is designed for compatibility with modern microcontrollers and digital logic systems. It provides differential output drive capability with controlled rise and fall characteristics. The receiver is designed with high input sensitivity and noise immunity to ensure accurate signal detection under varying bus conditions. The device includes thermal protection and safeguards against bus faults, including short-circuit conditions. Its internal circuitry is designed to maintain stable operation across a wide range of environmental conditions and supply variations. Interface Requirements The logic interface is compatible with standard digital input and output levels, allowing direct connection to a CAN controller. The bus interface consists of two differential lines that connect to the CAN network. Proper termination and layout practices are required to ensure optimal communication performance and compliance with CAN network design guidelines. Operating Conditions The device is intended for operation across a broad temperature range suitable for industrial and automotive environments. It maintains functional integrity under typical voltage fluctuations and environmental stresses encountered in embedded systems. Protection and Reliability Features The transceiver incorporates protection mechanisms to guard against overcurrent, thermal overload, and electrostatic discharge. It is designed to maintain communication reliability even in the presence of transient disturbances and electrical noise. Packaging and Integration The SN65HVD230DR is provided in a compact surface-mount package suitable for automated assembly. Its pin configuration supports straightforward integration into printed circuit board designs with minimal external components. #CommonPartsLibrary #IntegratedCircuits #Interface #Drivers #Receivers #Transceivers #65HVD230

4.7 µH Shielded Drum Core, Wirewound Inductor 2.6 A 105mOhm Max 2-SMD The SRP4020TA-4R7M is a compact surface-mount power inductor designed for use in high-efficiency power conversion and energy storage applications. It is optimized for switching regulators, DC-DC converters, and filtering circuits where stable inductance, low core loss, and reliable current handling are required. The device features a magnetically shielded construction that minimizes electromagnetic interference, making it suitable for densely populated electronic assemblies. Its robust design supports consistent performance across a wide range of operating conditions, contributing to improved system efficiency and reduced noise. Construction and Materials The component is manufactured using a ferrite core with integrated winding, enclosed in a molded structure that provides mechanical stability and environmental protection. The shielding structure reduces flux leakage and enhances electromagnetic compatibility. External terminations are designed for reliable solderability and strong adhesion to standard printed circuit board pads. Electrical Characteristics The inductor provides a nominal inductance corresponding to its designation and maintains stability under rated operating conditions. It exhibits low direct current resistance to minimize conduction losses and supports moderate to high current levels without significant saturation. The component is engineered to maintain performance over variations in temperature and frequency typical of switching power applications. Thermal Performance The device is capable of operating within standard industrial temperature ranges, with thermal characteristics that support efficient heat dissipation through the PCB. Its construction helps maintain inductance stability and prevents degradation under thermal stress. Mechanical Characteristics The package is a low-profile, surface-mount form factor suitable for automated assembly. The compact footprint enables use in space-constrained designs, while the structure ensures durability during handling and reflow soldering processes. Applications Typical applications include step-down and step-up voltage regulators, power management modules, portable electronics, telecommunications equipment, and general-purpose filtering where compact size and efficient performance are critical. Reliability and Compliance The component is designed to meet common industry reliability standards for surface-mount passive devices. It is compatible with standard reflow soldering processes and is typically compliant with environmental regulations governing hazardous substances. #commonpartslibrary #inductor