Through Hole straight socket strip, 01x07, 2.54mm pitch, single row #connector #pinsocket #tht

Through Hole straight socket strip, 01x20, 2.54mm pitch, single row #connector #pinsocket #tht

Welcome to your new project. Imagine what you can build here.

Welcome to your new project. Imagine what you can build here.

A 5x5 panel of very basic PCBs for a single Kailh MX hot swap socket in a keyboard matrix. Designed for COL2ROW diode direction.

Panel module for connecting D-SUB 25 via pin socket 02x13 #connector #D-SUB #25

SmartDeskPet v1.0 Shield Stage 1 status: - Goal: 5V input -> dual AMS1117-3.3 rails (+3V3_MCU and +3V3_WIFI) with common GND. - Note: Keep power nets explicitly named (avoid unnamed nets) to keep ERC happy. Stage 1 completion checklist: - Mark J1 Pin_1 (+5V) as a Power Output pin to satisfy ERC power-driver checks. - Verify all GND symbols/returns are on the same GND net. - Keep +5V_SERVO isolated from the main +5V net (only share GND). Stage 2 preparation notes (MPN/LCSC + layout constraints): - MPN/LCSC targets to define before Stage 2 exit: - AMS1117-3.3 (SOT-223): set exact MPN and (optionally) LCSC PN for both U1 and U2. - 100nF capacitor (0603): set MPN/LCSC for all 0603 100nF decouplers. - 4.7k resistor (0603): set MPN/LCSC for I2C pull-ups R1 and R2. - 1000uF bulk capacitor (radial): set MPN/LCSC for C7 (CP_Radial_D10.0mm_P5.00mm). - DC005 power jack/regulator input: select exact DC005 footprint + MPN/LCSC (if used). - 2.54mm headers/sockets: set MPN/LCSC for H1, H2, J1, J3, J4, J5, P3, P4, P5, and J2. - ESP-01S antenna keepout: - Reserve a copper keepout under and in front of the ESP-01S onboard antenna. - No copper pours/traces/components in the antenna region (top and bottom) per module guidelines. - H1/H2 header spacing: - Maintain 1000 mil spacing between H1 and H2 header centerlines (shield mechanical requirement). - Silkscreen placeholders: - Add silkscreen labels for: 5V IN, GND, +3V3_MCU, +3V3_WIFI, SERVO1, SERVO2, I2C SDA/SCL, DHT11, ASRPRO UART2, ESP-01S UART3. - Add placeholder text for: MPN, LCSC, board revision, and date code. Stage 3 layout constraints (placement and routing guidance): - Connector placement strategy: - Place H1 and H2 first to lock the shield mechanical interface; enforce 1000 mil spacing. - Place J1 and any DC005 input at the board edge for easy access. - Designated power area planning: - Group U1, U2, and C7 near the 5V entry point; keep high-current 5V and regulator loops short. - Use wide copper for +5V and any servo supply; stitch GND around power section. - Antenna keepout boundaries: - Place J2 (ESP-01S socket) at a board edge with the antenna facing outward. - Enforce a top-and-bottom copper keepout in the antenna region; keep noisy power traces away.

Universal 12V ESP32 Automation Motherboard with MOSFET Outputs, A4988 Stepper Socket, LM2596 5V Regulator & Expansion Headers

A 5x5 panel of very basic PCBs for a single Kailh Choc hot swap socket in a keyboard matrix. Designed for COL2ROW diode direction.

Very basic PCB for a single Kailh MX hot swap socket in a keyboard matrix. Designed for COL2ROW diode direction.

Power supply for breadboard.The module is compatible with 400 or 830 points Breadboard.The power supply must be supplied through a voltage of 5V and has an output through a Micro USB plug, or through a USB cable USB A and USB micro B socket.

Through Hole straight socket strip, 01x14, 2.54mm pitch, single row #pinsocket #tht

MikroBUS socket for EFR32xG24 Explorer Kit is a small form factor development and evaluation platform based on the EFR32MG24 System-on-Chip. The EFR32xG24 Explorer Kit is focused on rapid prototyping and concept creation of IoT applications for 2.4 GHz wireless protocols including Bluetooth LE, Bluetooth mesh, Zigbee, Thread, and Matter. #template #arduino-matter #arduino #siliconlabs #bluetooth #thread #zigbee #matter