Accelerometer X, Y, Z Axis ±2g, 4g, 8g 1.5kHz 14-CLCC (6x6) General Description The ADXL355BEZ is a low noise, low drift, low power, three-axis MEMS accelerometer intended for high-precision sensing applications. It delivers high-resolution digital acceleration data with excellent long-term stability and minimal temperature-induced variation. The device integrates a complete sensing chain, including the MEMS sensor element, analog conditioning, analog-to-digital conversion, and digital filtering. Output data is provided through SPI or I²C interfaces, enabling straightforward integration into embedded and industrial systems. Key Features Three-axis acceleration sensing (X, Y, Z) Selectable full-scale ranges: ±2 g, ±4 g, ±8 g Low noise density (~25 µg/√Hz) Low offset and minimal temperature drift High-resolution 20-bit digital output Integrated digital filtering SPI and I²C communication interfaces Low power consumption (~200 µA typical) Wide supply voltage range (2.25 V to 3.6 V) Integrated temperature sensor Hermetically sealed package Applications Structural health monitoring Vibration measurement and analysis Tilt and inclination sensing Industrial condition monitoring Navigation and inertial systems Seismic detection Robotics and stabilization platforms Functional Description The ADXL355BEZ includes an integrated sensing and processing architecture composed of: Three-axis MEMS sensing element Analog front-end signal conditioning High-resolution ADC Digital filtering and decimation stages Temperature sensing element Digital communication interface (SPI/I²C) Configuration and control registers Electrical Characteristics (Typical) Supply voltage: 2.25 V to 3.6 V Supply current: ~200 µA Output data rate: up to 4 kHz Noise density: ~25 µg/√Hz Resolution: 20-bit Interface: SPI / I²C Mechanical and Package Information Package type: LGA (Land Grid Array) Approximate dimensions: 3 mm × 5 mm × 1 mm Hermetically sealed for improved environmental robustness Interface and Communication Supports SPI (4-wire) and I²C protocols Outputs 20-bit acceleration data per axis Data format: two’s complement Measurement Ranges ±2 g ±4 g ±8 g Environmental Specifications Operating temperature range: -40°C to +125°C Storage temperature range: -55°C to +150°C Power Management Supports measurement and standby modes Designed for low-power operation in continuous sensing applications Compliance and Reliability Industrial-grade device Designed for long-term stability RoHS compliant #commonpartslibrary #sensor #accelerometer

MCP3913 Series 3.6 V 4.5 mA SMT Six-Channel Analog Front End - SSOP-28 The MCP3913A1T-E/SS is a high-performance, multi-channel analog front-end (AFE) from Microchip Technology intended for precision measurement applications. It features six simultaneous sampling 24-bit delta-sigma ADCs with integrated programmable gain amplifiers, enabling accurate acquisition of low-level analog signals. Designed for energy monitoring and industrial sensing, the device provides low noise, high dynamic range, and flexible configuration. It supports SPI communication for efficient interfacing with microcontrollers and digital processing systems. Key Features Six simultaneous sampling 24-bit delta-sigma ADC channels Integrated programmable gain amplifiers per channel High signal-to-noise ratio and low distortion Programmable oversampling ratios for performance tuning Internal voltage reference with external reference option SPI-compatible digital interface Configurable data output formats and control registers Low power operation modes Electrical Characteristics Resolution: 24-bit Number of Channels: 6 Input Configuration: Differential Supply Voltage: 2.7V to 3.6V Operating Temperature Range: -40°C to +125°C Programmable Gain: Up to 32 V/V (typical) Reference Voltage: Internal or external selectable Functional Description The device integrates six high-resolution delta-sigma ADCs that sample input signals simultaneously, ensuring accurate phase and timing relationships across channels. Each input passes through a programmable gain stage, allowing optimization for different sensor levels. Analog signals are digitized using oversampling and digital filtering techniques to achieve high precision and noise reduction. Configuration is handled via internal registers, and data is transferred through an SPI interface. Package Information Package Type: SSOP Pin Count: 28 Mounting Type: Surface Mount Applications Energy metering Power monitoring systems Industrial automation Multi-channel data acquisition Sensor interfacing Smart grid systems Advantages High integration reduces external components Simultaneous sampling improves measurement accuracy High resolution supports precise signal analysis Flexible configuration for various system requirements #commonpartslibrary #integratedcircuit #powermanagement #energymetering

ARM® Cortex®-M0+ MSPM0 C Microcontroller IC 32-Bit 24MHz 16KB (16K x 8) FLASH 8-DSBGA (0.86x1.6) MSPM0C110x microcontrollers (MCUs) are part of the MSP highly-integrated ultra-low-power 32-bit MCU family based on the enhanced Arm® Cortex®-M0+ core platform operating at up to 24MHz frequency. These costoptimized MCUs offer high-performance analog peripheral integration, support extended temperature ranges from -40°C to 125°C, and operate with supply voltages from 1.62V to 3.6V. The MSPM0C110x devices provide up to 16KB embedded flash program memory with 1KB SRAM. These MCUs incorporate a high-speed on-chip oscillator with an accuracy from -2% to +1.2%, eliminating the need for an external crystal. Additional features include a 1-channel DMA, CRC-16 accelerator, and a variety of highperformance analog peripherals such as one 12-bit 1.5Msps ADC with VDD as the voltage reference, and an on-chip temperature sensor. These devices also offer intelligent digital peripherals such as one 16-bit advanced timer, two 16-bit general purpose timer, one windowed watchdog timer, and a variety of communication peripherals including one UART, one SPI, and one I2C. These communication peripherals offer protocol support for LIN, IrDA, DALI, Manchester, smart card, SMBus, and PMBus. The TI MSPM0 family of low-power MCUs consists of devices with varying degrees of analog and digital integration let customers find the MCU that meets their project needs. The architecture combined with extensive low-power modes is optimized to achieve extended battery life in portable measurement applications. MSPM0C110x MCUs are supported by an extensive hardware and software ecosystem with reference designs and code examples to get the design started quickly. Development kits include a LaunchPad™ kit available for purchase and design files for a target-socket board. TI also provides a free MSP Software Development Kit (SDK), which is available as a component of Code Composer Studio™ IDE desktop and cloud version within the TI Resource Explorer. MSPM0 MCUs are also supported by extensive online collateral, training with MSP Academy, and online support through the TI E2E™ support forums. Features • Core – Arm® 32-bit Cortex®-M0+ CPU, frequency up to 24MHz • Operating characteristics – Extended temperature: –40°C to 125°C – Wide supply voltage range: 1.62V to 3.6V • Memories – Up to 16KB of flash – 1KB of SRAM • High-performance analog peripherals – One analog-to-digital converter (ADC) with up to 10 total external channels, 1.7Msps at 10 bit or 1.5Msps at 12 bit with VDD as the voltage reference – Configurable 1.4V or 2.5V internal ADC voltage reference (VREF) – Integrated temperature sensor – Integrated supply monitor • Optimized low-power modes – RUN: 87µA/MHz – STOP: 609µA at 4MHz, 311µA at 32kHz – STANDBY: 5µA with SRAM retention – SHUTDOWN: 200nA • Intelligent digital peripherals – 1-channel DMA controller dedicated for ADC – Three timers supporting up to 14 PWM channels • One 16-bit advanced timers with deadband support up to 8 PWM channels • One 16-bit general purpose timer with 4 capture/compares • One 16-bit general purpose timer with 2 capture/compares – Windowed watchdog timer – BEEPER generating 1kHz, 2kHz, 4kHz, or 8kHz square wave to drive the external beeper • Enhanced communication interfaces – One UART interface supporting LIN, IrDA, DALI, smart card, Manchester and low-power operation in STANDBY mode – One I2C interface supporting FM+ (1Mbps), SMBus, PMBus, and wakeup from STOP mode – One SPI supporting up to 12Mbps • Clock system – Internal 24MHz oscillator with an accuracy from -2% to +1.2% (SYSOSC) – Internal 32kHz low-frequency oscillator (LFOSC) • Data integrity – Cyclic redundancy checker (CRC-16) • Flexible I/O features – Up to 18 GPIOs – Two 5V-tolerant open-drain IOs • Development support – 2-pin serial wire debug (SWD) • Package options – 20-pin TSSOP (PW) – 20-pin VSSOP (DGS) – 20-pin WQFN (RUK) – 16-pin SOT (DYY) – 8-pin SOT (DDF) – 8-pin WSON (DSG) – 8-pin DSBGA (YCJ) • Family members (also see Device Comparison) – MSPS003F4: 16KB of flash, 1KB of RAM – MSPS003F3: 8KB of flash, 1KB of RAM – MSPM0C1104: 16KB of flash, 1KB of RAM – MSPM0C1103: 8KB of flash, 1KB of RAM • Development kits and software (also see Tools and Software) – LP-MSPM0C1104 LaunchPad™ development kit – MSP Software Development Kit (SDK) 2 Applications • Battery charging and management • Power supplies and power delivery • Personal electronics • Building security and fire safety • Connected peripherals and printers • Grid infrastructure • Smart metering • Communication modules • Medical and healthcare • Lighting #MSPM0C1104S8YCJR #MSPM0C1104 #TexasInstruments #CortexM0Plus #Microcontroller #EmbeddedSystems #LowPowerMCU #IoT #WearableDevices #IndustrialControl #ConsumerElectronics #ADC #UART #SPI #I2C #PWM #TI #ElectronicsDesign #PCBDesign #EmbeddedDevelopment

24 Bit Analog to Digital Converter 4, 8 Input 4 Sigma-Delta 56-VQFN (7x7) The ADS127L14 (quad) and ADS127L18 (octal) are 24-bit, delta-sigma (ΔΣ), analog-to-digital converters (ADCs) based on the single-channel ADS127L11. The devices provide simultaneous sampling of four or eight channels with data rates up to 512kSPS (wideband filter mode) and 1365kSPS (low-latency filter mode). Features • Simultaneously measure four or eight channels • Wideband filter mode: up to 512kSPS • Low-latency filter mode: up to 1365kSPS • Power-scalable speed modes: – Max speed: 512kSPS • 83mW (ADS127L14) • 165mW (ADS127L18) – High speed: 400kSPS • 64mW (ADS127L14) • 128mW (ADS127L18) – Mid speed: 200kSPS • 37mW (ADS127L14) • 74mW (ADS127L18) – Low speed: 50kSPS • 12mW (ADS127L14) • 24mW (ADS127L18) • AC performance with DC precision: (High-Speed Mode) – Dynamic range at 200kSPS: 112dB (typical) – THD: –118dB (typical) – INL: 1ppm of FSR (typical) – Offset drift: 10nV/°C (typical) – Gain drift: 0.5ppm/°C (typical) • Precharge buffered signal inputs • Programmable by pin setting or SPI • Frame-sync port for output data • Internal or external clock operation • Analog supply voltage: 2.85V to 5.5V 2 Applications • Test and measurement: – Data acquisition (DAQ) – Shock and vibration instruments – Acoustics and dynamic strain gauges • Factory automation and control: – Condition monitoring • Aerospace and defense: – Sonar • Medical: – Electroencephalograms (EEG) • Grid Infrastructure: – Power quality analyzers #ADS127L14IRSHT #TexasInstruments #ADC #DeltaSigmaADC #24BitADC #SimultaneousSampling #DataAcquisition #IndustrialAutomation #MedicalInstrumentation #PowerQuality #PrecisionMeasurement #EmbeddedSystems

A basic LED matrix grid for use in other projects.

BGA-16 1.92mm x 1.92mm 4X4 Pitch 0.5mm Ball Grid Array Footprint #generic-part-template

LQFP-32 is a surface-mount package for integrated circuits (ICs) with 32 leads arranged in a 7x7 mm square grid. The lead pitch is 0.8 mm, and the body size is approximately 7.0 mm x 7.0 mm x 1.4 mm (L x W x H). LQFP-32 is commonly used for microcontrollers, digital signal processors, and other complex ICs that require a high pin count. It provides a low-profile solution that is well-suited for space-constrained applications. 32-LQFP #part #template

LGA-16 is a small surface-mount package commonly used for electronic components. It has a body size of approximately 3 mm x 3 mm (L x W) with 16 pins. The lead pitch between the pins is typically 0.5 mm. The package is also known as Land Grid Array 16 or LGA-16. #part #template

TQFP-32 is a surface-mount package for integrated circuits (ICs) with 32 leads arranged in a 7x7 mm square grid. The lead pitch is 0.8 mm, and the body size is approximately 7.0 mm x 7.0 mm x 1.4 mm (L x W x H). TQFP-32 is commonly used for microcontrollers, digital signal processors, and other complex ICs that require a high pin count. 32-TQFP #part #template

LGA-12 is a small surface-mount package commonly used for electronic components. It has a body size of approximately 2 mm x 2 mm (L x W) with 12 pins. The lead pitch between the pins is typically 0.5 mm. The package is also known as Land Grid Array 12 or LGA-12. #part #template

LGA-8 is a small surface-mount package commonly used for integrated circuits. It has a body size of approximately 3 mm x 5 mm (L x W) with 8 pins. The lead pitch between the pins is typically 1.25 mm. The package is also known as Land Grid Array 8 or LGA-8. #part #template

Magnetic Sensors QMC5883L LGA-16_L3.0-W3.0-P0.50-BL_SQ The QMC5883L is a multi-chip three-axis magnetic sensor. This surface -mount, small sized chip has integrated magnetic sensors with signal condition ASIC, targeted for high precision applications such as compassing, navigation and gaming in drone, robot, mobile and personal hand-held devices. The QMC5883L is based on our state-of-the-art, high resolution, magneto-resistive technology licensed from Honeywell AMR technology. Along with custom-designed 16-bit ADC ASIC, it offers the advantages of low noise, high accuracy, low power consumption, offset cancellation and temperature compensation. QMC5883L enables 1° to 2° compass heading accuracy. The I²C serial bus allows for easy interface. The QMC5883L is in a 3x3x0.9mm3 surface mount 16-pin land grid array (LGA) package.  3-Axis Magneto-Resistive Sensors in a 3x3x0.9 mm3 Land Grid Array Package (LGA), guaranteed to operate over an extended temperature range of -40 °C to +85 °C.  Small Size for Highly Integrated Products. Signals Have Been Digitized And Calibrated.  16 Bit ADC With Low Noise AMR Sensors Achieves 2 Milli-Gauss Field Resolution  Enables 1° To 2° Degree Compass Heading Accuracy , Allows for Navigation and LBS Applications  Wide Magnetic Field Range (±8 Gauss)  Maximizes Sensor’s Full Dynamic Range and Resolution  Temperature Compensated Data Output and Temperature Output  Automatically Maintains Sensor’s Sensitivity Under Wide Operating Temperature Range  I 2C Interface with Standard and Fast Modes.  High-Speed Interfaces for Fast Data Communications. Maximum 200Hz Data Output Rate  Wide Range Operation Voltage (2.16V To 3.6V) and Low Power Consumption (75A)  Compatible with Battery Powered Applications  Lead Free Package Construction  RoHS Compliance  Software And Algorithm Support Available  Compassing Heading, Hard Iron, Soft Iron, and Auto Calibration Libraries Available #CommonPartsLibrary #Sensor

3D accelerometer and 3D gyroscope The LSM6DS3TR-C is a system-in-package featuring a 3D digital accelerometer and a 3D digital gyroscope performing at 0.90 mA in high-performance mode and enabling always-on low-power features for an optimal motion experience for the consumer. The LSM6DS3TR-C supports main OS requirements, offering real, virtual and batch sensors with 4 kbyte for dynamic data batching. ST’s family of MEMS sensor modules leverages the robust and mature manufacturing processes already used for the production of micromachined accelerometers and gyroscopes. The various sensing elements are manufactured using specialized micromachining processes, while the IC interfaces are developed using CMOS technology that allows the design of a dedicated circuit which is trimmed to better match the characteristics of the sensing element. The LSM6DS3TR-C has a full-scale acceleration range of ±2/±4/±8/±16 g and an angular rate range of ±125/±250/±500/±1000/±2000 dps. High robustness to mechanical shock makes the LSM6DS3TR-C the preferred choice of system designers for the creation and manufacturing of reliable products. The LSM6DS3TR-C is available in a plastic land grid array (LGA) package. Features  “Always-on” experience with low power consumption for both accelerometer and gyroscope  Power consumption: 0.90 mA in combo highperformance mode  Smart FIFO up to 4 kbyte based on features set  Android M compliant  Hard, soft ironing for external magnetic sensor corrections  ±2/±4/±8/±16 g full scale  ±125/±250/±500/±1000/±2000 dps full scale  Analog supply voltage: 1.71 V to 3.6 V  Independent IO supply (1.62 V)  Compact footprint, 2.5 mm x 3 mm x 0.83 mm  SPI & I2C serial interface with main processor data synchronization feature  Pedometer, step detector and step counter  Significant motion and tilt function  Standard interrupts: free-fall, wakeup, 6D/4D orientation, click and double-click  Embedded temperature sensor  ECOPACK®, RoHS and “Green” compliant #CommonPartsLibrary #Sensor

15 µH Shielded Drum Core, Wirewound Inductor 3.5 A 92mOhm Max Nonstandard The SRP7050TA-150M is a high-performance photovoltaic module designed for utility-scale and large commercial solar power applications. The module utilizes advanced monocrystalline cell technology to deliver high energy conversion efficiency, reliable power generation, and long-term operational stability under varying environmental conditions. Its robust mechanical construction and optimized electrical characteristics provide dependable performance in demanding outdoor installations, including regions exposed to high wind loads, elevated temperatures, and extended solar irradiance. The module is engineered to support high system voltage configurations while maintaining low degradation rates and enhanced energy yield over its service life. The design incorporates reinforced framing, tempered high-transmission glass, and weather-resistant encapsulation materials to ensure durability against moisture ingress, ultraviolet exposure, and mechanical stress. The product is suitable for fixed-tilt and tracker-based mounting systems and is compatible with standard industry installation practices. Electrical performance is optimized for maximum power output with improved temperature behavior and reduced resistive losses. The module supports efficient integration into modern photovoltaic systems requiring high-density energy production and reliable long-term operation. Safety and quality compliance are aligned with internationally recognized photovoltaic module standards for performance, durability, and environmental resilience. The SRP7050TA-150M is intended for grid-connected solar energy systems where high efficiency, operational reliability, and reduced balance-of-system costs are critical project requirements. #commonpartslibrary #inductor

Temperature Sensor Digital, Infrared (IR) 14-SMD Module #CommonPartsLibrary #IntegratedCircuit #Sensor #Transducer #Temperature-Sensor #Grid-EYE #AMG883