USB Type C PMIC 40-TQFN (6x6) The MAX25432 combines an automotive-grade buckboost controller capable of full-range 3.3V to 21V programmable power supply (PPS) at up to 6.35A, USB Power Delivery (USB PD) analog front-end (AFE), legacy USB charging support, and USB Type-C® protection switches for automotive USB host or downstream-facing (DFP) applications. The USB TypeC protection switches provide automotive system-level ESD protection and 24V short-circuit protection for D+, D-, CC1, CC2, and VCONN. The device can optionally support legacy charging modes for older passenger phones including BC1.2, Apple® Charge, Apple CarPlay®, Apple MFi, and USB On-The-Go (OTG). The MAX25432B integrates a USB PD AFE, which supports the USB-IF Type-C Port Controller Interface (TCPCI) specification and can interface with any I2C controller in the application. The MAX25432A provides configuration channel (CC) signal pass-through protection for an external USB PD controller. P-suffix and G-suffix devices include intelligent detection and protection to avoid high short-circuit currents flowing from the car battery through the cable shield to ground during fault events, thus preventing car module damage. The MAX25432 is available in a small, 6mm x 6mm, 40- pin TQFN-EP package and requires very few external components. The MAX25432 evaluation (EV) kit and collateral provide a convenient platform to the design engineer for rapid evaluation with reduced test and firmware development time. Integrated I2C Buck-Boost Controller with PPS 4.5V to 36V Input Operating Range 3.3V to 21V Constant Voltage, 10mV LSB 1A to 6.35A Current Limit, 25mA LSB 220kHz, 300kHz, and 400kHz SwitchingFrequency VBUS Cable Compensation up to 516mΩ External Frequency Synchronization and SpreadSpectrum for Reduced EMI USB PD 3.1 Type-C Port Controller USB-IF Compliant - TID 9154 Up to 800mV Ground Offset Pairs with ADI TCPM for Turn-Key Solution MAX25432BATLP Enables: ADI TCPM Alternate Mode and Dual-Role Port Improved CC Detection Advanced Monitoring Algorithms (V, T) Dynamic Loop Control Highest Performance, Safest, and Lowest Cost Passenger Cable-Shield Short-to-Battery Protection Minimizes Short-Circuit Currents with a Small,Single-FET Solution Integrated Current-Sense Amplifiers, ADC and DAC Integrated 3.3V to 5.0V, 1.5W, Smart, Reliable VCONN Switches and Protection, 50mA to 500mA OCP Integrated 24V DC Protection on Protected HVD+, HVD-, HVCC1, HVCC2 Outputs Integrated Legacy USB 2.0 Charging Support Including BC1.2, Apple CarPlay, OTG, and Apple MFi Rev 3x Integrated ±15kV Air-Gap/±8kV Contact Discharge ISO 10605 and IEC 61000-4-2 ESD Protection -40°C to +125°C Operating Temperature Range 40-Pin, 6mm x 6mm, TQFN Package with EP AEC-Q100 and AEC-Q006 Qualified #CommonPartsLibrary #IntegratedCircuit #PowerManagement

Frequency to Voltage Converter IC 10 kHz ±0.3% 8-PDIP #commonpartslibrary #integratedcircuit #powermanagement #voltageconverter

Frequency to Voltage Converter IC 10 kHz ±0.3% 8-SOIC #commonpartslibrary #integratedcircuit #powermanagement #voltageconverter

Frequency Synthesizer IC 27MHz, 60MHz 1 SOT-23-6 #Timer #commonpartslibrary

3x Frequency Multiplier, output 300 to 450 MHz, 50 Ohm, Mini-Circuits TT1224, 6-SMD #commonpartslibrary #RF #integratedcircuit

5x Frequency Multiplier, Output 37.5 to 52.5 MHz, 50 Ohm, Mini-Circuits TT1224 #commonpartslibrary #RF #integratedcircuit

High Frequency Synchronous Rectifier Controller, 1MHz, Min On Time = 375ns, SOT-23-5 synchronous rectifier controller SOT?23*

High Frequency Half Bridge Driver, Output Current 2.0A, 175V, CMOS Input, SOIC-8 Half Bridge Gate Driver SOIC*3.9x4.9mm*P1.27mm*

High Frequency Half Bridge Driver, Output Current 2.0A, 100V, QFN-16 Half Bridge Gate Driver QFN*1EP*5x5mm*P0.8mm*

High Frequency Half Bridge Driver, Output Current 2.0A, 100V, DFN-8 Half Bridge Gate Driver DFN*1EP*4x4mm*P0.5mm*

High Frequency Half Bridge Driver, Output Current 2.0A, 175V, CMOS Input, SOIC-8 Half Bridge Gate Driver SOIC*3.9x4.9mm*P1.27mm*

Programmable Frequency, One Cycle Control PFC IC, Continuous Conduction Mode, SOIC-8 pfc controller ccm SOIC*3.9x4.9mm*P1.27mm*

High Frequency Half Bridge Driver, Output Current 2.0A, 100V, SOIC-8 Half Bridge Gate Driver SOIC*3.9x4.9mm*P1.27mm*

3.8V to 32V Input, 2A Low Quiescent Current Synchronous Buck Converter with Enhanced EMI Suppression The AP63200/AP63201/AP63203/AP63205 is a 2A, synchronous buck converter with a wide input voltage range of 3.8V to 32V and fully integrates a 125mΩ high-side power MOSFET and a 68mΩ low-side power MOSFET to provide high-efficiency step-down DC/DC conversion. The AP63200/AP63201/AP63203/AP63205 device is easily used by minimizing the external component count due to its adoption of peak current mode control along with its integrated compensation network. The AP63200/AP63201/AP63203/AP63205 has optimized designs for Electromagnetic Interference (EMI) reduction. The converter features Frequency Spread Spectrum (FSS) with a switching frequency jitter of ±6%, which reduces EMI by not allowing emitted energy to stay in any one frequency for a significant period of time. It also has a proprietary gate driver scheme to resist switching node ringing without sacrificing MOSFET turn-on and turn-off times, which further erases highfrequency radiated EMI noise caused by MOSFET switching. The device is available in a low-profile, TSOT26 package • VIN 3.8V to 32V • 2A Continuous Output Current • 0.8V ±1% Reference Voltage • 22µA Ultralow Quiescent Current • Switching Frequency o 500kHz: AP63200 and AP63201 o 1.1MHz: AP63203 and AP63205 • Pulse Width Modulation (PWM) Regardless of Output Load o AP63201 • Supports Pulse Frequency Modulation (PFM) o AP63200, AP63203, and AP63205 o Up to 80% Efficiency at 1mA Light Load o Up to 88% Efficiency at 5mA Light Load • Fixed Output Voltage o 3.3V: AP63203 o 5.0V: AP63205 • Proprietary Gate Driver Design for Best EMI Reduction • Frequency Spread Spectrum (FSS) to Reduce EMI • Precision Enable Threshold to Adjust UVLO • Protection Circuitry o Overvoltage Protection o Cycle-by-Cycle Peak Current Limit o Thermal Shutdown #CommonPartsLibrary #IntegratedCircuit #PowerManagement #Switching-regulator

3.8V to 32V Input, 2A Low Quiescent Current Synchronous Buck Converter with Enhanced EMI Suppression The AP63200/AP63201/AP63203/AP63205 is a 2A, synchronous buck converter with a wide input voltage range of 3.8V to 32V and fully integrates a 125mΩ high-side power MOSFET and a 68mΩ low-side power MOSFET to provide high-efficiency step-down DC/DC conversion. The AP63200/AP63201/AP63203/AP63205 device is easily used by minimizing the external component count due to its adoption of peak current mode control along with its integrated compensation network. The AP63200/AP63201/AP63203/AP63205 has optimized designs for Electromagnetic Interference (EMI) reduction. The converter features Frequency Spread Spectrum (FSS) with a switching frequency jitter of ±6%, which reduces EMI by not allowing emitted energy to stay in any one frequency for a significant period of time. It also has a proprietary gate driver scheme to resist switching node ringing without sacrificing MOSFET turn-on and turn-off times, which further erases highfrequency radiated EMI noise caused by MOSFET switching. The device is available in a low-profile, TSOT26 package • VIN 3.8V to 32V • 2A Continuous Output Current • 0.8V ±1% Reference Voltage • 22µA Ultralow Quiescent Current • Switching Frequency o 500kHz: AP63200 and AP63201 o 1.1MHz: AP63203 and AP63205 • Pulse Width Modulation (PWM) Regardless of Output Load o AP63201 • Supports Pulse Frequency Modulation (PFM) o AP63200, AP63203, and AP63205 o Up to 80% Efficiency at 1mA Light Load o Up to 88% Efficiency at 5mA Light Load • Fixed Output Voltage o 3.3V: AP63203 o 5.0V: AP63205 • Proprietary Gate Driver Design for Best EMI Reduction • Frequency Spread Spectrum (FSS) to Reduce EMI • Precision Enable Threshold to Adjust UVLO • Protection Circuitry o Overvoltage Protection o Cycle-by-Cycle Peak Current Limit o Thermal Shutdown #CommonPartsLibrary #IntegratedCircuit #PowerManagement

The CC1101RGP is a low-power sub-gigahertz RF transceiver designed for wireless communication applications requiring reliable long-range data transmission and high receiver sensitivity. It integrates a complete radio frequency front-end, packet handling engine, modulation and demodulation circuitry, frequency synthesizer, and advanced power management features within a compact package. The device supports multiple modulation formats and is optimized for industrial, scientific, medical, smart metering, home automation, remote control, wireless sensor networks, and Internet of Things applications. Its flexible configuration options enable designers to achieve an optimal balance between communication range, data throughput, power consumption, and system robustness. Features Sub-gigahertz RF transceiver for license-free ISM frequency bands High receiver sensitivity for extended communication range Programmable output power for optimized power consumption Multiple modulation schemes including FSK, GFSK, ASK, OOK, and MSK Integrated packet handling and error detection functions Fast frequency synthesizer settling time Low current consumption in transmit, receive, and sleep modes Hardware support for address filtering and data buffering Programmable channel spacing and data rate configuration Integrated RSSI, LQI, and clear channel assessment functions SPI interface for configuration and data communication Suitable for battery-powered wireless devices Applications Smart metering systems Wireless sensor networks Industrial monitoring and control Home and building automation Remote keyless entry systems Alarm and security systems Asset tracking devices Telemetry and data acquisition systems IoT communication nodes Proprietary wireless communication networks Electrical Characteristics Wide operating supply voltage range Low-power transmit and receive operation Programmable RF output power levels High-performance frequency synthesizer Low standby and sleep current consumption Integrated crystal oscillator support Robust RF performance across supported frequency bands Interface and Connectivity Serial Peripheral Interface communication Digital control and status signals Configurable interrupt outputs Integrated FIFO buffers for transmit and receive data External antenna connection through matching network Package Information Surface-mount package suitable for automated assembly Compact footprint for space-constrained applications RoHS-compliant device construction #commonpartslibrary #integratedcircuit #wirelesscommunication #rftransceiver #subghz #iot #embeddedsystems #industrialautomation #smartmetering #wirelesssensornetwork #lowpowerdesign #telemetry #homeautomation #remotecontrol #texasinstruments

Radio Frequency Cable HJ-MCX009 ANT-TH_L6.0-W6.0_MCX-KE LCSC Part Number: C2904906 JLCPCB Part Class: Extended Part Manufactured by 皇捷

RF IC Frequency Multiplier General Purpose 20MHz ~ 1GHz #commonpartslibrary #RF #integratedcircuit

Voltage to Frequency Converter IC 1 MHz ±0.012% 8-MSOP #commonpartslibrary #integratedcircuit #powermanagement #voltageconverter

400MHz Bandwidth Frequency Synthesizer, LFCSP-20 Analog Devices PFD LFCSP*1EP*4x4mm*P0.5mm*