48V tether-powered Ethernet-to-WiFi bridge using Blue Robotics Fathom-X style tether interface and ESP32-S3 WiFi output, with isolated/buck DC/DC rails for the tether interface and ESP32.

Smart relay based on ESP32-S3 with CAN bus module extension capability

Multi-processor AI development board with STM32MP157-class MPU, RP2350/RP2040 companion MCU, ESP32-S3 WiFi/BT, DDR3L, storage, Ethernet, display/camera/audio, USB-C PD/DC power, and 100 mm x 72 mm 4-layer PCB target.

Autonomous 12 V solar/battery powered 5-zone balcony irrigation ESP32-S3 carrier/control board

Production-prototype ESP32-S3 control/RF/GNSS/sensor board for an outdoor livestock collar. Includes LoRa 915 MHz, GNSS, I2C/I2S sensors, local actuator drivers, battery-cell solder pads, solar pass-through, soldered flex-tail zones, HV electrode isolation, test points, and a 120 mm x 80 mm 4-layer FR4 target stackup.

ESP32-S3 + C6 controller. 4× thermocouple, 2× SSR, CAN, ▎ 3.5" QSPI display (FRU mezzanine), tire SELV loop. ▎ 4-layer, 130×90mm. SmarTemp+ standard.

Compact ESP32-S3 wearable environmental monitor with BME688 sensing, LiPo charging, MAX17043 fuel gauge, USB-C power, and JLCPCB-ready 4-layer layout constraints.

70x50 mm CNC-friendly raw-laminate XIAO ESP32S3 lapel audio recorder prototype with socketed XIAO, dual external INMP441 microphones, LiPo connector, button/status LED, and SD-card recording support. Layout prioritizes hand soldering, replaceable parts, wide traces, and generous isolation clearances over compactness.

ESP32-S3 based 6x8 flip-dot matrix controller using DRV8833 H-bridges, USB-C 5V input, AP2112K 3.3V logic rail, and a 48-coil row/column inductor matrix.

WalkInPeace belt-clip wearable PCB for 8-channel EMG, IMU, ESP32-S3 classification, haptic/audio alerts, BLE/WiFi notifications, and rechargeable LiPo power management.

Vibe-hardwared ESP32-S3 e-ink handheld project created with no prior technical knowledge on May 12, 2026, in about 30 minutes of real time.

Smart weighing + vision recognition controller using a Seeed XIAO ESP32-S3, Grove Vision AI V2 connected only by 3V3/GND/SDA/SCL, and a simple four-pin ESP32-S3 expansion interface for D2/GPIO3 and D3/GPIO4; no onboard HX711 or load-cell connector.

Beginner-friendly button-triggered speaker sound playback PCB with USB loading/debug, microSD storage, ESP32-S3 controller, and I2S speaker amplifier.

Low-power consumer environmental sensor node with ESP32-S3 Wi-Fi/BLE, digital temperature/humidity sensing, USB-C 5 V default-sink input, reverse/OVP/UVLO/OCP protection, and regulated 3.3 V power for 0.5–3 A USB-C sources.

ESP32-S3 intelligent egg incubator schematic with camera-based egg verification, load-cell assessment, environmental sensing, heater/humidifier/fan control, servo turning, and OLED status display.

Ø39 mm ESP32-S3 Gesture Gimbal Phone Holder Main PCB

Consumer USB-C powered low-power temperature/humidity sensor node with ESP32-S3 Wi-Fi/BLE, SHT31 I2C sensor, protected 5V input, 3.3V regulation, debug access, and RF-aware PCB layout.

Jerky Robot V3 100 mm × 152 mm 2-layer control board with ESP32-S3 and Arduino Nano sockets, screw-terminal I/O, BSS138 UART level shifting, PC817 sensor isolation, optional HX711 interface, status LEDs, test points, top-side component placement, and bottom GND fill for JLCPCB fabrication.

ESP32-S3 quadcopter flight controller with OV5640 24-pin DVP camera interface, Wi-Fi video link, BLE telemetry, onboard USB-C power/programming, IMU, barometer, ToF altitude sensing, lidar connector, and 4 ESC PWM outputs.

Beginner-friendly battery-powered ESP32-S3 board with USB-C charging/programming, LiPo power-path charging, three flex sensor inputs, one I2C IMU, and two haptic driver outputs.

Compact 60 mm x 40 mm child safety wearable PCB with ESP32-S3, SIM800L GSM, NEO-6M GPS, MPU-6050, MAX30102, USB-C charging/programming, LiPo battery input, and test-pointed I2C/UART power rails. Target layout is 2-layer with all components on top, bottom ground plane, short direct I2C/UART routing, and GSM placement isolated from GPS and sensor sections.

Meshtastic ESP32-S3 node with 5 V input, 3.3V low-noise regulation, and I2C expansion.

Have you ever wanted to wake up to one of the most energizing scents? Have you ever wanted that cup of energy in your hands before you even slide out of your covers? Well want no further! Introducing the Coffee Waker; The knight of your nightstand, a coffee maker alarm clock with one soul purpose, to quickly and scrumptiously wake you up. This is the Coffee Waker Main board. It contains an ESP32-S3, 16 bit Load Cell ADC, 16 bit MP3 DAC, 120V heater cartridge relay, and 12C wakeup light convector.

ESP32-S3 door access controller with USB-C Li-ion charging, VBAT and 12V lock power, dual 3.3V rails, I2C sensor headers, reed/PIR inputs, LED indicators, buzzer, and MOSFET plus relay lock outputs. External modules and field devices remain represented by connector placeholders with documented pinouts for later PCB and validation work.

Passive BLE tracker locator with ESP32-S3, 2.4-inch TFT UI, USB-C charging, LiPo battery power, GNSS logging, 2.4 GHz BLE/Wi-Fi energy detection, passive BLE advertisement identification in firmware, and optional ADL5904 cellular-band sensing.

Audio-first ESP32-S3 wearable PCB. 44 × 26 × 1.0 mm. ESP32-S3-MINI-1 + INMP441 + TP4056 + DW01A/FS8205A + ME6211C33. 800mAh 802545 LiPo. Native USB on GPIO19/20. BLE audio wearable.

Bilateral smart running insole data logger using two nearly identical ESP32-S3 pressure-sensing PCBs. Left variant is an ESP-NOW slave without microSD; right variant is the master with microSD logging. Both preserve the 16-zone FSR mux front end, LiPo charging, AP2112K regulation, USB-C charging input, JST battery connector, and the 280mm x 90mm 2-layer low-profile insole form factor.

Glove interface board using Seeed Studio XIAO ESP32S3. Manufacturing path updated for partial assembly: preserve existing glove interface circuitry (FSR inputs on J3-J7, I2C on J8, SPI on J9, pull resistors R1-R7, decoupling C1) and source U1 separately because JLCPCB stock for MPN 113991114 is unavailable. Assemble all other parts normally, leave U1 for customer-supplied/manual installation, and do not substitute U1 unless a verified XIAO-format pin-compatible replacement is explicitly approved.

Raijin Drums autonomous touring controller integrating piezo trigger inputs, ESP32-S3 processing, WS281x LED outputs, MIDI DIN/USB, and DMX512 in a 19-inch 1U rackmount chassis. Design intent includes Neutrik panel connectors, internal IEC-powered 12V supply architecture, crimped harness wiring, vibration-aware mechanical support, and review traceability for schematic and PCB cleanup.

Misty Pink Replicator schematic finalized for layout handoff with ESP32-S3, USB-C battery charging, T5838 always-on wake microphone, CI1302 backup ASR analog microphone front end, HTEW0154T8 SPI e-ink display, standardized power/test nets, and final ERC-clean baseline.

Self-Powered RF Transceiver Module for EM Sensing with RF Prescaler, Divider Chain, and ESP32-S3 Interface

Compressor PCB - ESP32-S3 HVAC field sensing (24 VAC + CT + UART)

ESP32-S3 Wearable Audio Streaming Pendant (USB-C + LiPo + I2S Mic + microSD + OLED)

AeroHUD VariScope Mark 1 - ESP32-S3 RF module vario/airspeed HUD with Qwiic OLED and SDP810, GPS, USB-C data+charging

ESP32-S3 CAM Audio-Visual Controller with I2S MEMS Microphone, Class-D Amplifier, SPI Display, Servos, Capacitive Touch and Integrated USB-C Power-Only Sink (VBUS via J6 -> 5V_IN -> SW1:P1 -> 5V_SW, CC1/CC2 5.1 kOhm to GND, VBUS TVS Surge Protection) + Added optional bulk electrolytic caps on 5V_SW near servo headers

3.3V ESP32-S3 Dual 6V Rail MOSFET Board with MCP23017 I2C Expanders, Option C Gate Network, SW2 DPST Rail-Interlock, 2S LiFePO4 Charger/BMS (BQ24618 + BQ29209) with Series Battery Wiring and Charge Integration, and 2×10 RA Headers (#MCP23017_3V3 #OptionC #GateNetwork #RailInterlock #Dual6V #BQ24618 #BQ29209 #2S #LiFePO4 #SeriesBattery #ChargeIntegration #RAHeaders)

Architectural Lavender Translation Collar – ESP32‑S3 Wi‑Fi + LoRa, USB‑C, Li‑ion, low‑power design Overview Experience a cutting-edge IoT solution with this low‑power board built around the ESP32‑S3‑MINI‑1‑N8. Designed for seamless Wi‑Fi (2.4 GHz), BLE, and LoRa (868 MHz) connectivity, this board integrates ENS161 and ENS210 sensors over I2C alongside an RFM95W‑868 LoRa radio on SPI. It is powered via a 3.7 V Li‑ion cell with USB‑C charging up to 500 mA, complete with full battery protection, a robust 3.3 V rail tailored for Wi‑Fi burst currents, and per‑peripheral power gating to enhance energy efficiency. Core Features • MCU: ESP32‑S3‑MINI‑1‑N8 equipped with an onboard PCB antenna for 2.4 GHz Wi‑Fi/BLE, ensuring optimal wireless performance. • Sensors: Integrated ENS161 and ENS210 sensors utilize a shared I2C bus with controllable 4.7 kΩ pull‑ups for streamlined communication. • LoRa Radio: The RFM95W‑868 module, connected via SPI, enables long‑range communication at 868 MHz. Power & USB‑C Connectivity • Battery: A reliable 3.7 V 1200 mAh Li‑ion battery connected via a right‑angle JST‑PH 2‑pin connector features built‑in battery protection. • Charging: The USB‑C receptacle, with CC resistors and TVS protection on D+/D− along with series resistors, supports fast, safe charging with a current limit of 500 mA. • Regulation: A dedicated 3.3 V regulator capable of handling Wi‑Fi burst currents coupled with bulk and high‑frequency decoupling ensures stable operation, supported by status LEDs indicating power and charge states. Low‑Power Control • Peripheral Management: Load switches allow selective power‑gating of the ENS161, ENS210, and RFM95W modules, controlled directly by ESP32‑S3 GPIOs. • Energy Efficiency: Controllable I2C pull‑ups minimize idle current, vital for prolonged battery life in IoT applications. RF and Antenna Integration • 2.4 GHz: Utilizes the integrated PCB antenna on the ESP32‑S3 with proper ground/metal keep‑out zones for optimal signal integrity. • 868 MHz: Features a controlled‑impedance feed from the RFM95W to a PI matching network (C‑L‑C pads) with flexible antenna options—selectable via SMA connector, chip antenna, or PCB trace—and includes RF ESD protection. Connectivity & Debug Features • USB‑C Interface: Provides secure data connectivity with integrated safeguards and proper terminations. • Debugging: A comprehensive programming/debug header exposes EN, BOOT, and UART lines, with test points on key rails and buses (3V3, VBAT, SCK, MOSI, MISO, SDA, SCL, RESET/EN, GND) to simplify development and troubleshooting. Design Verification • Rigorous ERC/DRC and decoupling checks ensure adherence to component ratings and optimal signal routing. • Maintain RF keep‑outs and impedance‑controlled traces for both 2.4 GHz and 868 MHz paths, securing reliable performance even during high‑intensity operations. #IoT #ESP32S3 #LoRa #LowPowerDesign #USB-C #WirelessConnectivity #BatteryPowered #RFDesign

ESP32-S3 CAM Audio-Visual Controller with I2S MEMS Microphone, Class-D Amplifier, SPI Display, Servos, Capacitive Touch and Integrated USB-C Power-Only Sink (VBUS via J6 → 5V_IN → SW1:P1 → 5V_SW, CC1/CC2 5.1 kΩ to GND, VBUS TVS Surge Protection) #USB_C #PowerManagement #5V

Compact 4-Layer ESP32-S3-DevKitC-1 Nano-Style Carrier Board with I²S Audio, Class-D Amp, MicroSD, LiPo Power, WS2812B, and IR; featuring updated all-layer antenna keepout, additional decoupling capacitors on 5 V/3.3 V rails, four M3 mounting holes, finalized rounded-corner PCB outline and hand-friendly width, centered ESP32-S3-DevKitC-1 and symmetrically aligned MicroSD/I²S mic, centered bottom silkscreen title text, and zero-error ERC/DRC; layout is finalized and ready for routing #ESP32S3 #DevKitC1 #antennaKeepout #decoupling #M3MountingHoles #routingReady

ESP32-S3 Voice Assistant Core Board (50x50 mm, 4-Layer) with USB-C, Li-ion Power Management, and I2S Audio – Design Ready for PCB Layout and Fabrication

Low-Power USB-C (5 V) Environmental Sensor Node with 18650 Li-Ion Power-Path, Robust Protection (Reverse Polarity, OVP, UVLO, OCP to 3 A), Dual-Radio ESP32-S3 MCU, I²C VOC/Temp/Humidity/Pressure/Lux Sensors, and 2-/4-Pin JST-XH Expansion Pads for Battery and Sensors #USB-C #LiIon #ESP32 #I2C #PowerProtection #EnvironmentalSensor

ESP32S3 XIAO ePaper HAT+ Driver Board with Integrated Power Rails and SPI Interface

Production-Ready 2-Layer ESP32-S3 Controller PCB: Dual WROOM-1U/WROOM-1 Footprints, ESD-Protected USB-C Debug, Protected 12 V Input (Fuse, Reverse Diode, TVS), TPS5430DDA Buck + TLV70033DDCT LDO Power, Integrated TMC2209 Stepper Driver, 3× 12 V/2 A LED Channels with Screw Terminals, Comprehensive Test Points, Full BOM/Pin Map/Gerbers, Logic Power Supply Audited and Validated #ESP32S3 #PowerManagement #MotorControl #LEDControl #ProductionReady #PowerAudit

Silent Gaude: 10 mm 4‑Layer ESP32-S3 LTE/GNSS Wearable Bracelet

Phase 1 Solder-Free ESP32-S3 Telephone Audio Guestbook Adapter

ESP32-S3 Audio Logger with Real-time Ambient Capture using I2S MEMS Microphone

3.3V LiPo-Powered UWB Sensor Node: XIAO ESP32S3 & RyUwb_lite Integration

Bounce Puller Rev B USB-C Edition: Robust Power Management with ESP32-S3, Li-Ion Charging, and Hall Sensor

Glitch Engine: ESP32-S3 Audio & Video FX Platform with High-Speed ADC/DAC, CVBS I/O, Analog/Digital Glitch Blocks, USB-C, Protected CV/Clock Inputs, and 4-Layer Split AGND/DGND PCB

ESP32-S3 Four-Axis Stepper Motor Controller and Solenoid Driver Board