Pin Function Grouping

Looking at the datasheet of this component, can you group together pins by their functions? for example for Power, 3v3, gnd_1 gnd_2 etc

NOTE: If you group them, can you not add the same pin if you already added them in a group? You should know which pin function is common for its function

3 days

flux

2:13

Consulting on datasheets.

Looking for "ADXL354 pin configuration pin function descriptions 14 terminal LCC pin names numbers" in adxl354_adxl355.pdf

Looking for "Table pin function descriptions ADXL354 pins V1P8ANA V1P8DIG VSUPPLY VDDIO GND VOUTX VOUTY VOUTZ ST1 ST2 TEMP NC EPAD" in adxl354_adxl355.pdf

Looking for "ADXL354 Table 8 Pin Function Descriptions pin 1 pin 7 mnemonic no connect reserved" in adxl354_adxl355.pdf

Looking for "ADXL354 pin configuration figure 10 14 terminal LCC pins 1 7" in adxl354_adxl355.pdf

I grouped the ADXL354BEZ pins from the datasheet with each pin assigned exactly once: Power, Ground, Analog Outputs, Control / Mode Select, and Self Test. Full details are in the ADXL354BEZ Pin Function Groups project file.

3 days

adrian95

Use these groups to update the symbol pin organization.

3 days

flux

0:37

Updating project properties.

Analyzing the schematic.

Updated the ADXL354BEZ symbol terminal organization using the documented groups, with each pin assigned to exactly one Section and Pin Group. I also set pin types, orientations, and short pin descriptions for Power, Ground, Analog Outputs, Control / Mode Select, and Self Test pins.

Run ERC/DRC

Show pin grouping

Check datasheet guidance

Verify footprint match

3 days

Set Section to "Power" on VSUPPLY, VDDIO, V1P8DIG, and 1 more, Set Pin Group to "Power" on VSUPPLY, VDDIO, V1P8DIG, and 1 more, and 29 more changes

Set VSUPPLY's Section to "Power"

Set VSUPPLY's Pin Group to "Power"

Set VSUPPLY's Pin Type to "Power In"

Set VSUPPLY's Pin Orientation to "Top"

Set VSUPPLY's Pin Description to "Main supply input"

Set VDDIO's Section to "Power"

Set VDDIO's Pin Group to "Power"

Set VDDIO's Pin Type to "Power In"

Set VDDIO's Pin Orientation to "Top"

Set VDDIO's Pin Description to "Digital interface supply"

Set V1P8DIG's Section to "Power"

Set V1P8DIG's Pin Group to "Power"

Set V1P8DIG's Pin Type to "Power In"

Set V1P8DIG's Pin Orientation to "Top"

Set V1P8DIG's Pin Description to "Digital 1.8V supply"

Set V1P8ANA's Section to "Power"

Set V1P8ANA's Pin Group to "Power"

Set V1P8ANA's Pin Type to "Power In"

Set V1P8ANA's Pin Orientation to "Top"

Set V1P8ANA's Pin Description to "Analog 1.8V supply"

Set VSSIO's Section to "Ground"

Set VSSIO's Pin Group to "Ground"

Set VSSIO's Pin Type to "Ground"

Set VSSIO's Pin Orientation to "Bottom"

Set VSSIO's Pin Description to "Digital ground return"

Set VSS's Section to "Ground"

Set VSS's Pin Group to "Ground"

Set VSS's Pin Type to "Ground"

Set VSS's Pin Orientation to "Bottom"

Set VSS's Pin Description to "Analog ground return"

Set TEMP's Section to "Analog"

Set TEMP's Pin Group to "Analog Outputs"

Set TEMP's Pin Type to "Output"

Set TEMP's Pin Orientation to "Right"

Set TEMP's Pin Description to "Temperature sensor output"

Set XOUT's Section to "Analog"

Set XOUT's Pin Group to "Analog Outputs"

Set XOUT's Pin Type to "Output"

Set XOUT's Pin Orientation to "Right"

Set XOUT's Pin Description to "X-axis analog output"

Set YOUT's Section to "Analog"

Set YOUT's Pin Group to "Analog Outputs"

Set YOUT's Pin Type to "Output"

Set YOUT's Pin Orientation to "Right"

Set YOUT's Pin Description to "Y-axis analog output"

Set ZOUT's Section to "Analog"

Set ZOUT's Pin Group to "Analog Outputs"

Set ZOUT's Pin Type to "Output"

Set ZOUT's Pin Orientation to "Right"

Set ZOUT's Pin Description to "Z-axis analog output"

Set RANGE's Section to "Control"

Set RANGE's Pin Group to "Control / Mode Select"

Set RANGE's Pin Type to "Input"

Set RANGE's Pin Orientation to "Left"

Set RANGE's Pin Description to "Range selection input"

Set ~STBY's Section to "Control"

Set ~STBY's Pin Group to "Control / Mode Select"

Set ~STBY's Pin Type to "Input"

Set ~STBY's Pin Orientation to "Left"

Set ~STBY's Pin Description to "Standby mode input"

Set ST1's Section to "Control"

Set ST1's Pin Group to "Self Test"

Set ST1's Pin Type to "Input"

Set ST1's Pin Orientation to "Left"

Set ST1's Pin Description to "Self-test enable input"

Set ST2's Section to "Control"

Set ST2's Pin Group to "Self Test"

Set ST2's Pin Type to "Input"

Set ST2's Pin Orientation to "Left"

Set ST2's Pin Description to "Self-test actuation input"

3 days

ZOUT

V1P8DIG

ST1

VSUPPLY

TEMP

ST2

RANGE

~STBY

VSSIO

XOUT

V1P8ANA

YOUT

VDDIO

Reviews

Ground
A common return path for electric current. Commonly known as ground.
jharwinbarrozo
20.5M
Net Portal
Wirelessly connects nets on schematic. Used to organize schematics and separate functional blocks. To wirelessly connect net portals, give them same designator. #portal
jharwinbarrozo
43.0M
Power Net Portal
Wirelessly connects power nets on schematic. Identical to the net portal, but with a power symbol. Used to organize schematics and separate functional blocks. To wirelessly connect power net portals, give them the same designator. #portal #power
jharwinbarrozo
11.4M
Generic Resistor
A generic fixed resistor ideal for rapid circuit topology development. Its footprint automatically adapts based on the selected package case code—supporting 0402, 0603, 0805, 1203, and many other standard SMD packages, as well as axial horizontal and vertical configurations. Save precious design time by seamlessly add more information to this part (value, footprint, etc.) as it becomes available. Standard resistor values: 1.0 ohm, 10 ohm, 100 ohm, 1.0k ohm, 10k ohm, 100k ohm, 1.0M ohm 1.1 ohm, 11 ohm, 110 ohm, 1.1k ohm, 11k ohm, 110k ohm, 1.1M ohm 1.2 ohm, 12 ohm, 120 ohm, 1.2k ohm, 12k ohm, 120k ohm, 1.2M ohm 1.3 ohm, 13 ohm, 130 ohm, 1.3k ohm, 13k ohm, 130k ohm, 1.3M ohm 1.5 ohm, 15 ohm, 150 ohm, 1.5k ohm, 15k ohm, 150k ohm, 1.5M ohm 1.6 ohm, 16 ohm, 160 ohm, 1.6k ohm, 16k ohm, 160k ohm, 1.6M ohm 1.8 ohm, 18 ohm, 180 ohm, 1.8K ohm, 18k ohm, 180k ohm, 1.8M ohm 2.0 ohm, 20 ohm, 200 ohm, 2.0k ohm, 20k ohm, 200k ohm, 2.0M ohm 2.2 ohm, 22 ohm, 220 ohm, 2.2k ohm, 22k ohm, 220k ohm, 2.2M ohm 2.4 ohm, 24 ohm, 240 ohm, 2.4k ohm, 24k ohm, 240k ohm, 2.4M ohm 2.7 ohm, 27 ohm, 270 ohm, 2.7k ohm, 27k ohm, 270k ohm, 2.7M ohm 3.0 ohm, 30 ohm, 300 ohm, 3.0K ohm, 30K ohm, 300K ohm, 3.0M ohm 3.3 ohm, 33 ohm, 330 ohm, 3.3k ohm, 33k ohm, 330k ohm, 3.3M ohm 3.6 ohm, 36 ohm, 360 ohm, 3.6k ohm, 36k ohm, 360k ohm, 3.6M ohm 3.9 ohm, 39 ohm, 390 ohm, 3.9k ohm, 39k ohm, 390k ohm, 3.9M ohm 4.3 ohm, 43 ohm, 430 ohm, 4.3k ohm, 43K ohm, 430K ohm, 4.3M ohm 4.7 ohm, 47 ohm, 470 ohm, 4.7k ohm, 47k ohm, 470k ohm, 4.7M ohm 5.1 ohm, 51 ohm, 510 ohm, 5.1k ohm, 51k ohm, 510k ohm, 5.1M ohm 5.6 ohm, 56 ohm, 560 ohm, 5.6k ohm, 56k ohm, 560k ohm, 5.6M ohm 6.2 ohm, 62 ohm, 620 ohm, 6.2k ohm, 62K ohm, 620K ohm, 6.2M ohm 6.8 ohm, 68 ohm, 680 ohm, 6.8k ohm, 68k ohm, 680k ohm, 6.8M ohm 7.5 ohm, 75 ohm, 750 ohm, 7.5k ohm, 75k ohm, 750k ohm, 7.5M ohm 8.2 ohm, 82 ohm, 820 ohm, 8.2k ohm, 82k ohm, 820k ohm, 8.2M ohm 9.1 ohm, 91 ohm, 910 ohm, 9.1k ohm, 91k ohm, 910k ohm, 9.1M ohm #generics #CommonPartsLibrary
jharwinbarrozo
1.5M
Generic Capacitor
A generic fixed capacitor ideal for rapid circuit topology development. You can choose between polarized and non-polarized types, its symbol and the footprint will automatically adapt based on your selection. Supported options include standard SMD sizes for ceramic capacitors (e.g., 0402, 0603, 0805), SMD sizes for aluminum electrolytic capacitors, and through-hole footprints for polarized capacitors. Save precious design time by seamlessly add more information to this part (value, footprint, etc.) as it becomes available. Standard capacitor values: 1.0pF, 10pF, 100pF, 1000pF, 0.01uF, 0.1uF, 1.0uF, 10uF, 100uF, 1000uF, 10000uF 1.1pF, 11pF, 110pF, 1100pF 1.2pF, 12pF, 120pF, 1200pF 1.3pF, 13pF, 130pF, 1300pF 1.5pF, 15pF, 150pF, 1500pF, 0.015uF, 0.15uF, 1.5uF, 15uF, 150uF, 1500uF 1.6pF, 16pF, 160pF, 1600pF 1.8pF, 18pF, 180pF, 1800pF 2.0pF, 20pF, 200pF, 2000pF 2.2pF, 22pF, 220pF, 2200pF, 0.022uF, 0.22uF, 2.2uF, 22uF, 220uF, 2200uF 2.4pF, 24pF, 240pF, 2400pF 2.7pF, 27pF, 270pF, 2700pF 3.0pF, 30pF, 300pF, 3000pF 3.3pF, 33pF, 330pF, 3300pF, 0.033uF, 0.33uF, 3.3uF, 33uF, 330uF, 3300uF 3.6pF, 36pF, 360pF, 3600pF 3.9pF, 39pF, 390pF, 3900pF 4.3pF, 43pF, 430pF, 4300pF 4.7pF, 47pF, 470pF, 4700pF, 0.047uF, 0.47uF, 4.7uF, 47uF, 470uF, 4700uF 5.1pF, 51pF, 510pF, 5100pF 5.6pF, 56pF, 560pF, 5600pF 6.2pF, 62pF, 620pF, 6200pF 6.8pF, 68pF, 680pF, 6800pF, 0.068uF, 0.68uF, 6.8uF, 68uF, 680uF, 6800uF 7.5pF, 75pF, 750pF, 7500pF 8.2pF, 82pF, 820pF, 8200pF 9.1pF, 91pF, 910pF, 9100pF #generics #CommonPartsLibrary
jharwinbarrozo
1.5M
Generic Inductor
A generic fixed inductor suitable for rapid circuit topology development. The footprint automatically adapts based on the selected package, supporting standard SMD sizes (e.g., 0402, 0603, 0805) as well as well-known inductor packages such as SDR1806, PA4320, SRN6028, and SRR1260. Standard inductor values: 1.0 nH, 10 nH, 100 nH, 1.0 µH, 10 µH, 100 µH, 1.0 mH 1.2 nH, 12 nH, 120 nH, 1.2 µH, 12 µH, 120 µH, 1.2 mH 1.5 nH, 15 nH, 150 nH, 1.5 µH, 15 µH, 150 µH, 1.5 mH 1.8 nH, 18 nH, 180 nH, 1.8 µH, 18 µH, 180 µH, 1.8 mH 2.2 nH, 22 nH, 220 nH, 2.2 µH, 22 µH, 220 µH, 2.2 mH 2.7 nH, 27 nH, 270 nH, 2.7 µH, 27 µH, 270 µH, 2.7 mH 3.3 nH, 33 nH, 330 nH, 3.3 µH, 33 µH, 330 µH, 3.3 mH 3.9 nH, 39 nH, 390 nH, 3.9 µH, 39 µH, 390 µH, 3.9 mH 4.7 nH, 47 nH, 470 nH, 4.7 µH, 47 µH, 470 µH, 4.7 mH 5.6 nH, 56 nH, 560 nH, 5.6 µH, 56 µH, 560 µH, 5.6 mH 6.8 nH, 68 nH, 680 nH, 6.8 µH, 68 µH, 680 µH, 6.8 mH 8.2 nH, 82 nH, 820 nH, 8.2 µH, 82 µH, 820 µH, 8.2 mH #generics #CommonPartsLibrary
jharwinbarrozo
15.9k
Terminal
An electrical connector acting as reusable interface to a conductor and creating a point where external circuits can be connected.
natarius
RMCF0805JT47K0
General Purpose Thick Film Standard Power and High-Power Chip Resistor 47 kOhms ±5% 0.125W, 1/8W Chip Resistor 0805 (2012 Metric) Automotive AEC-Q200 Thick Film Features: - RMCF – standard power ratings - RMCP – high power ratings - Nickel barrier terminations standard - Power derating from 100% at 70ºC to zero at +155ºC - RoHS compliant, REACH compliant, and halogen free - AEC-Q200 compliant
jharwinbarrozo
1.2M
875105359001
10 µF 16 V Aluminum - Polymer Capacitors Radial, Can - SMD 30mOhm 2000 Hrs @ 105°C #commonpartslibrary #capacitor #aluminumpolymer #radialcan
jharwinbarrozo
1.2M
CTL1206FYW1T
Yellow 595nm LED Indication - Discrete 1.7V 1206 (3216 Metric)
jharwinbarrozo
1.1M

Project Name

ADXL354BEZ

Description

Accelerometer X, Y, Z Axis ±2g, 4g 1.5kHz 14-CLCC (6x6)

General Description

The ADXL354BEZ is a low noise, low drift, low power, 3-axis MEMS accelerometer designed for high precision sensing applications. It provides analog voltage outputs proportional to acceleration along the X, Y, and Z axes. The device is optimized for applications requiring high resolution and long-term stability, including structural health monitoring, condition monitoring, tilt sensing, and seismic measurements.

The sensor features excellent temperature stability, minimal offset drift, and selectable measurement ranges. Its very low noise density makes it suitable for vibration analysis and other sensitive measurement environments.

Key Features 3-axis MEMS accelerometer with analog outputs Selectable measurement ranges of ±2 g, ±4 g, and ±8 g Ultra-low noise density of approximately 20 µg/√Hz Low offset drift across temperature Low power consumption of approximately 150 µA (typical) High resolution and measurement stability Integrated temperature sensor output Hermetically sealed package for improved environmental robustness Functional Description

The ADXL354BEZ measures acceleration using capacitive MEMS sensing elements arranged along three orthogonal axes. When acceleration is applied, the internal sensing structure experiences displacement, causing a change in capacitance. This change is converted into an analog voltage output for each axis.

Each axis produces a continuous-time analog signal, allowing direct interfacing with external analog-to-digital converters or signal conditioning circuits. Internal signal conditioning ensures low noise performance and stable output behavior.

Electrical Characteristics (Typical)

The device operates with a supply voltage ranging from 2.25 V to 3.6 V. Typical supply current during normal operation is approximately 150 µA. The noise density for all three axes is around 20 µg/√Hz. The bandwidth is user selectable and can reach up to approximately 1.5 kHz. The output signals are analog and ratiometric with respect to the supply voltage.

Mechanical Characteristics

The ADXL354BEZ is housed in a compact leadless chip carrier (LCC) package with approximate dimensions of 5 mm by 5 mm. It is designed for surface-mount installation. The sensing axes are aligned orthogonally to provide accurate three-dimensional acceleration measurement.

Performance Characteristics High resolution suitable for precision sensing applications Low temperature coefficient and minimal drift over time High linearity across the full-scale measurement range Excellent long-term stability Low cross-axis sensitivity for improved accuracy Pin Configuration Overview

The device includes power supply and ground connections, along with individual analog outputs for each axis labeled XOUT, YOUT, and ZOUT. A self-test pin is provided for functionality verification, and a temperature output pin allows monitoring of internal device temperature.

Operating Conditions

The device is designed to operate over a temperature range from −40°C to +125°C. Storage temperature ranges from −65°C to +150°C. The recommended supply voltage range is 2.25 V to 3.6 V.

Applications Structural health monitoring Industrial condition monitoring Seismic and geophysical sensing Tilt and inclination measurement Platform stabilization systems Vibration analysis Advantages Extremely low noise performance for high sensitivity applications Stable operation across wide temperature ranges Simple analog interface without the need for digital communication protocols Robust packaging suitable for harsh environments Compliance and Reliability

The ADXL354BEZ is RoHS compliant and designed for industrial-grade applications. It offers high reliability and long-term performance stability in demanding operating conditions.

#commonpartslibrary #sensor #accelerometer

Properties

Part Type

Sensor

Manufac…er Name

Analog Devices Inc.

Manufac… Number

ADXL354BEZ

Datasheet URL

analog.com/media/en/technical-documentation/data-sheets/adxl354_adxl355.pdf

Designator Prefix

License

creativecommons.org/licenses/by/4.0/

Symbol Style

parametric-v1

Pricing & Availability

Distributor	Qty 1

Controls

Welcome 👋

Flux accelerates your PCB design with AI.

Create your account to start using this component and bring your ideas to life.

adrian95 / ADXL354BEZ

Schematic

Introducing AI Placement!