Schematic Design Review and Analysis
1:06
Project
D14/A0
P2
Below is a schematic-level analysis based on the information in the project and the review reports:
Table
- U1:11 with SW3:3
- U1:12 with SW4:3
- U1:9 with SW1:3
- U1:10 with SW2:3
- Similar issues with U1 and LCD1 as well as between U1 and K1
| Revisit the net assignments and physical wire routing. Ensure that wires are directly connected to the center of the pads—redraw or reassign the nets if necessary so that all intended connections overlap properly, thereby satisfying the airwire criteria. | | Missing I2C Bus Pull-Ups | The DS1307+ (U2) uses the SDA (pin 5) and SCL (pin 6) lines, which appear on nets with signals from [U2] and a corresponding [U1] pin (e.g., U1:13 and U1:14 per errors). | Add standard pull-up resistors (typically around 4.7 kΩ each) on both the SDA and SCL lines to the supply voltage (VCC) per DS1307+ best practices. | | Lack of Decoupling Capacitors on Power Pins | The power inputs for U1 (e.g., +5V and +3V3) and the VCC for U2 have no local bypass capacitors. | Place decoupling capacitors—typically one 100 nF capacitor near each power pin for high-frequency noise filtering and an additional 10 µF capacitor for bulk capacitance—close to the ICs. | | Potential Relay Drive Issues | The relay (K1) has its coil controlled from a U1 output (error noted between U1:23 and K1:COIL2). | Confirm that the drive signal to the relay coil includes proper current limiting. If needed, incorporate a transistor driver stage or series resistor (with a value calculated according to the relay coil specifications) to protect the microcontroller output. | | Ambiguous Pin Assignments / Incorrect Net Connections | Several U1 pins appear to be used for connections that may not match their intended electrical function (for instance, U1:13 intended for I2C SDA versus an analog/digital pin assignment). Errors such as “U1:13, U2:5: Error” and “U1:14, U2:6: Error” indicate misalignment between the microcontroller’s pin functions and the connected signals. | Verify the pin functions on U1 against your design requirements. Reassign the functions to appropriate I/O pins (for example, dedicate specific pins for I2C) and update net labels accordingly to match the actual intended use. |
Summary:
The existing schematic shows multiple airwire errors that point to physical connection issues (i.e., wires not connecting at the center of pads) and a few functional blocks that need enhancement. By improving net routing, adding required pull-ups for the I2C bus, incorporating decoupling capacitors at the IC power pins, and ensuring proper drive circuitry for the relay, you can help ensure both electrical integrity and reliable operation.
The existing schematic shows multiple airwire errors that point to physical connection issues (i.e., wires not connecting at the center of pads) and a few functional blocks that need enhancement. By improving net routing, adding required pull-ups for the I2C bus, incorporating decoupling capacitors at the IC power pins, and ensuring proper drive circuitry for the relay, you can help ensure both electrical integrity and reliable operation.
Please review each of these points in your schematic and adjust the physical wiring and component placements accordingly.
Add required decoupling capacitors
Add pull-up resistors for I2C
Verify relay drive circuitry
369 days
Ready.
U2
PowerNet2
SW3
SW4
SW1
PowerNet1
SW2
U1
LCD1
K1
Reviews
- Wirelessly connects nets on schematic. Used to organize schematics and separate functional blocks. To wirelessly connect net portals, give them same designator. #portaljharwinbarrozo43.0M
- Wirelessly connects power nets on schematic. Identical to the net portal, but with a power symbol. Used to organize schematics and separate functional blocks. To wirelessly connect power net portals, give them the same designator. #portal #powerjharwinbarrozo11.4M
- A generic fixed resistor for rapid developing circuit topology. Save precious design time by seamlessly add more information to this part (value, footprint, etc.) as it becomes available. Standard resistor values: 1.0Ω 10Ω 100Ω 1.0kΩ 10kΩ 100kΩ 1.0MΩ 1.1Ω 11Ω 110Ω 1.1kΩ 11kΩ 110kΩ 1.1MΩ 1.2Ω 12Ω 120Ω 1.2kΩ 12kΩ 120kΩ 1.2MΩ 1.3Ω 13Ω 130Ω 1.3kΩ 13kΩ 130kΩ 1.3MΩ 1.5Ω 15Ω 150Ω 1.5kΩ 15kΩ 150kΩ 1.5MΩ 1.6Ω 16Ω 160Ω 1.6kΩ 16kΩ 160kΩ 1.6MΩ 1.8Ω 18Ω 180Ω 1.8KΩ 18kΩ 180kΩ 1.8MΩ 2.0Ω 20Ω 200Ω 2.0kΩ 20kΩ 200kΩ 2.0MΩ 2.2Ω 22Ω 220Ω 2.2kΩ 22kΩ 220kΩ 2.2MΩ 2.4Ω 24Ω 240Ω 2.4kΩ 24kΩ 240kΩ 2.4MΩ 2.7Ω 27Ω 270Ω 2.7kΩ 27kΩ 270kΩ 2.7MΩ 3.0Ω 30Ω 300Ω 3.0KΩ 30KΩ 300KΩ 3.0MΩ 3.3Ω 33Ω 330Ω 3.3kΩ 33kΩ 330kΩ 3.3MΩ 3.6Ω 36Ω 360Ω 3.6kΩ 36kΩ 360kΩ 3.6MΩ 3.9Ω 39Ω 390Ω 3.9kΩ 39kΩ 390kΩ 3.9MΩ 4.3Ω 43Ω 430Ω 4.3kΩ 43KΩ 430KΩ 4.3MΩ 4.7Ω 47Ω 470Ω 4.7kΩ 47kΩ 470kΩ 4.7MΩ 5.1Ω 51Ω 510Ω 5.1kΩ 51kΩ 510kΩ 5.1MΩ 5.6Ω 56Ω 560Ω 5.6kΩ 56kΩ 560kΩ 5.6MΩ 6.2Ω 62Ω 620Ω 6.2kΩ 62KΩ 620KΩ 6.2MΩ 6.8Ω 68Ω 680Ω 6.8kΩ 68kΩ 680kΩ 6.8MΩ 7.5Ω 75Ω 750Ω 7.5kΩ 75kΩ 750kΩ 7.5MΩ 8.2Ω 82Ω 820Ω 8.2kΩ 82kΩ 820kΩ 8.2MΩ 9.1Ω 91Ω 910Ω 9.1kΩ 91kΩ 910kΩ 9.1MΩ #generics #CommonPartsLibraryjharwinbarrozo1.5M
- A generic fixed capacitor ideal for rapid circuit topology development. You can choose between polarized and non-polarized types, its symbol and the footprint will automatically adapt based on your selection. Supported options include standard SMD sizes for ceramic capacitors (e.g., 0402, 0603, 0805), SMD sizes for aluminum electrolytic capacitors, and through-hole footprints for polarized capacitors. Save precious design time by seamlessly add more information to this part (value, footprint, etc.) as it becomes available. Standard capacitor values: 1.0pF 10pF 100pF 1000pF 0.01uF 0.1uF 1.0uF 10uF 100uF 1000uF 10,000uF 1.1pF 11pF 110pF 1100pF 1.2pF 12pF 120pF 1200pF 1.3pF 13pF 130pF 1300pF 1.5pF 15pF 150pF 1500pF 0.015uF 0.15uF 1.5uF 15uF 150uF 1500uF 1.6pF 16pF 160pF 1600pF 1.8pF 18pF 180pF 1800pF 2.0pF 20pF 200pF 2000pF 2.2pF 22pF 20pF 2200pF 0.022uF 0.22uF 2.2uF 22uF 220uF 2200uF 2.4pF 24pF 240pF 2400pF 2.7pF 27pF 270pF 2700pF 3.0pF 30pF 300pF 3000pF 3.3pF 33pF 330pF 3300pF 0.033uF 0.33uF 3.3uF 33uF 330uF 3300uF 3.6pF 36pF 360pF 3600pF 3.9pF 39pF 390pF 3900pF 4.3pF 43pF 430pF 4300pF 4.7pF 47pF 470pF 4700pF 0.047uF 0.47uF 4.7uF 47uF 470uF 4700uF 5.1pF 51pF 510pF 5100pF 5.6pF 56pF 560pF 5600pF 6.2pF 62pF 620pF 6200pF 6.8pF 68pF 680pF 6800pF 0.068uF 0.68uF 6.8uF 68uF 680uF 6800uF 7.5pF 75pF 750pF 7500pF 8.2pF 82pF 820pF 8200pF 9.1pF 91pF 910pF 9100pF #generics #CommonPartsLibraryjharwinbarrozo1.5M
- A generic fixed inductor for rapid developing circuit topology. *You can now change the footprint and 3D model at the top level anytime you want. This is the power of #genericsjharwinbarrozo15.5k
- An electrical connector acting as reusable interface to a conductor and creating a point where external circuits can be connected.Terminal
- 47 kOhms ±5% 0.125W, 1/8W Chip Resistor 0805 (2012 Metric) Automotive AEC-Q200 Thick Film #forLedBlinkjharwinbarrozo1.2M
- 10uF Capacitor Aluminum Polymer 20% 16V SMD 5x5.3mm #forLedBlink #commonpartslibrary #capacitor #aluminumpolymer #radialcanjharwinbarrozo1.2M
- Yellow 595nm LED Indication - Discrete 1.7V 1206 (3216 Metric) #forLedBlinkjharwinbarrozo1.1M
Welcome to your new project. Imagine what you can build here.
Properties
Properties describe core aspects of the project.
Pricing & Availability
Distributor | Qty 1 |
|---|
Assets
No assets added.
Controls
Welcome 👋
Flux helps you build PCBs faster with an AI teammate!
Create your account to collaborate, stay updated, fork your own version, and get instant answers from our AI agent.