Solid State SPST-NO (1 Form A) x 2 8-SMD (0.300", 7.62mm) #CommonPartsLibrary #Relay #SolidStateRelay

MOSFET Output Solid-State Relay (PhotoMOS® Relay) – Single-pole normally open (1 Form A) solid-state relay with a MOSFET output for low-level signal switching and isolation. Provides 3750 Vrms input-to-output isolation, supports 60 V maximum load voltage, 0.4 A continuous load current, and 2.5 Ω maximum on-state resistance. Features an LED input with 3 mA maximum operate current, 1 ms maximum turn-on/turn-off time, 100 pF typical output capacitance, and is housed in a 4-pin SOP surface-mount package. Operates over a −40°C to +85°C temperature range. #Aratas #G3VM201AY1 #SolidStateRelay #PhotoMOS #MOSFETRelay #SSR #OpticallyIsolatedRelay #SignalSwitch #1FormA #SOP4 #SurfaceMount #EmbeddedSystems

IXYS Integrated Circuits brings OptoMOS® technology, reliability and compact size to a new family of high-power Solid State Relays. As part of this family, the CPC1709J single-pole normally open (1-Form-A) DC Solid State Power Relay employs optically coupled MOSFET technology to provide 2500Vrms of input to output isolation. The output, constructed with an efficient MOSFET switch and photovoltaic die, uses IXYS Integrated Circuits’ patented OptoMOS architecture while the input, a highly efficient infrared LED, provides the optically coupled control. The combination of low on-resistance and high load current handling capability makes this relay suitable for a variety of high performance DC switching applications. The unique ISOPLUS-264 package pioneered by IXYS enables Solid State Relays to achieve the highest load current and power ratings. This package features a unique IXYS process where the silicon chips are soft soldered onto the Direct Copper Bond (DCB) substrate instead of the traditional copper leadframe. The DCB ceramic, the same substrate used in high power modules, not only provides 2500Vrms isolation but also very low junction-to-case thermal impedance (0.3 °C/W). Features • 22.8ADC Load Current with 5°C/W Heat Sink • Low 0.05 On-Resistance • 60VP Blocking Voltage • 2500Vrms Input/Output Isolation • Low Thermal Impedance: JC = 0.3 °C/W • Isolated, Low Thermal Impedance Ceramic Pad for Heat Sink Applications • Low Drive Power Requirements • No EMI/RFI Generation Applications • Industrial Controls / Motor Control • Robotics • Medical Equipment—Patient/Equipment Isolation • Instrumentation • Multiplexers • Data Acquisition • Electronic Switching • I/O Subsystems • Meters (Watt-Hour, Water, Gas) • Transportation Equipment #CPC1709J #IXYS #Littelfuse #SolidStateRelay #SSR #OptoMOS #PowerRelay #DCRelay #MOSFETRelay #HighCurrentSwitching #ElectricalIsolation #IndustrialElectronics #PowerManagement #BatterySystems #AutomationControl

Power Switch/Driver 1:1 N-Channel 500mA PowerSSO-12 8-channel protected high-side 12 V output switch IC The VNI2140J is a monolithic device designed using STMicroelectronics' VIPower technology. The device drives two independent resistive or inductive loads with one side connected to ground. Active current limitation prevents a drop in system power supply in cases of shorted-load, and built-in thermal shutdown protects the chip from damage due to overtemperature and short-circuit. In overload conditions, channel turns OFF and ON automatically to maintain the junction temperature between TTSD and TR. If the case temperature reaches TCSD, the overloaded channel is turned OFF and restarts only when case temperature decreases down to TCR. In order to avoid high-peak current from the supply, when more than one channel is overloaded the TCSD restart is not simultaneous. Non overloaded channels continue to operate normally. The open-drain diagnostics output indicates overtemperature conditions and open-load in OFF-state. Features • Nominal current: 0.75 A per channel • Shorted-load protections • Junction overtemperature protection • Case overtemperature protection for thermal independence of the channels • Thermal case shutdown restart not simultaneous for the various channels • Protection against loss of ground • Current limitation 1 A per channel • Undervoltage shutdown • Open-load in OFF-state and short to VCC detection • Open-drain diagnostic outputs • 3.3 V CMOS/TTL compatible inputs • Fast demagnetization of inductive loads • Conforms to IEC 61131-2 Applications • Programmable logic control • Industrial PC peripheral input/output • Numerical control machines #VNI2140J #STMicroelectronics #VIPower #HighSideSwitch #SolidStateRelay #PowerManagement #IndustrialAutomation #PLC #LoadDriver #PowerSSO12

Solid State SPST-NO (1 Form A) 4-SIP #Relauy #SolidStateRelay

Solid State DPST-NO (2 Form A) 11-SOIC (0.295", 7.50mm Width) #Relay #SolidStateRelay

Solid State SPST-NO (1 Form A) 4-SIP #relay #solidstaterelay #spstno

Solid State Photo-Coupled Relay (Photorelay) SPST-NO (1 Form A) 4-SMD (0.300", 7.62mm) Solid-state PhotoMOS relay providing a 1 Form A (SPST-NO) isolated switch for AC/DC load control. It supports 60 V load voltage, 0.55 A continuous load current, 5,000 Vrms input-to-output isolation, and is housed in a surface-mount DIP4 package, with 0.85 Ω typical on-resistance and 2.5 Ω maximum on-resistance. #PanasonicElectricWorks #AQY212EHA #PhotoMOS #SolidStateRelay #SSR #Photorelay #1FormA #SPSTNO #60V #550mA #DIP4 #SurfaceMount

Photorelay with a 1-Form-A (normally open) MOSFET output, designed for isolated solid-state switching applications. It features a 200 V OFF-state output voltage, 200 mA ON-state current, 1 mA maximum trigger LED current, 8 Ω maximum ON-state resistance, 1500 Vrms minimum isolation voltage, and is housed in a 4-pin SOP (2.54SOP4) package. #Photorelay #MOSFETOutput #Optocoupler #1FormA #SolidStateRelay #Isolation #200V #200mA #SOP4 #ToshibaSemiconductor