Bipolar (BJT) Transistor NPN 40V 200 mA 300MHz 300 mW Surface Mount SOT-23-3 (TO-236) The MMBT3904LT1G is a general-purpose NPN bipolar junction transistor designed for switching and amplification applications. It is housed in a compact SOT-23 surface-mount package, making it suitable for high-density PCB designs. This transistor is widely used in low-power signal processing, digital switching, and analog amplification circuits due to its reliable performance and fast switching characteristics. Key Features General-purpose NPN transistor Compact SOT-23 surface-mount package Fast switching speed Low saturation voltage Suitable for low-current and low-power applications High reliability and stability Pb-free, Halogen-free, and RoHS compliant Electrical Characteristics (Typical @ 25°C unless otherwise specified) Collector-Emitter Voltage (VCEO): 40 V Collector-Base Voltage (VCBO): 60 V Emitter-Base Voltage (VEBO): 6 V Collector Current (IC): 200 mA (max) DC Current Gain (hFE): 100 – 300 Collector-Emitter Saturation Voltage (VCE(sat)): 0.2 V (typ) Transition Frequency (fT): ~300 MHz Absolute Maximum Ratings Collector Current (Continuous): 200 mA Power Dissipation: ~225 mW Junction Temperature: +150°C (max) Operating Temperature Range: -55°C to +150°C Storage Temperature Range: -55°C to +150°C Mechanical Characteristics Package Type: SOT-23 (TO-236AB) Mounting Type: Surface Mount Number of Pins: 3 Marking Code: Dependent on lot/manufacturer marking Applications General-purpose switching circuits Signal amplification Digital logic interfacing LED drivers and small load switching Audio and RF signal processing #CommonPartsLibrary #TransistorBJT #MMBT2222

The NE555 devices are precision timing circuits capable of producing accurate time delays or oscillation. In time-delay or monostable operating modes, the timed interval is controlled by a single external resistor and capacitor network. In the astable mode of operation, the frequency and duty cycle are controlled independently with two external resistors and a single external capacitor. Each timer has a trigger level equal to approximately one-third of the supply voltage and a threshold level equal to approximately two-thirds of the supply voltage. These levels can be altered by use of the control voltage pin (CONT). When the trigger input (TRIG) is less than the trigger level, the flip-flop is set and the output goes high. If TRIG is greater than the trigger level and the threshold input (THRES) is greater than the threshold level, the flip-flop is reset and the output is low. The reset input (RESET) overrides all other inputs and is used to initiate a new timing cycle. If RESET is low, the flip-flop is reset and the output is low. Whenever the output is low, a lowimpedance path is provided between the discharge pin (DISCH) and the ground pin (GND). Tie all unused inputs to an appropriate logic level to prevent false triggering. The output circuit is capable of sinking or sourcing current up to 200mA. Operation is specified for supplies of 5V to 15V. With a 5V supply, output levels are compatible with TTL inputs. Features - Timing from microseconds to hours - Astable or monostable operation - Adjustable duty cycle - TTL-compatible output can sink or source up to 200mA - On products compliant to MIL-PRF-38535, all parameters are tested unless otherwise noted. Applications - Pulse-shaping circuits - Missing-pulse detectors - Pulse-width modulators - Pulse-position modulators - Sequential timers - Pulse generators -F requency dividers - Industrial controls

An xtal electronic oscillator circuit that uses the mechanical resonance of a vibrating crystal of piezoelectric material to create an electrical signal with a precise frequency.

ARM® Cortex®-M0+ STM32G0 Microcontroller IC 32-Bit Single-Core 64MHz 32KB (32K x 8) FLASH 8-SOIC The STM32G031J6M6 is a compact, low-power 32-bit microcontroller from STMicroelectronics, based on the Arm® Cortex®-M0+ core running at up to 64 MHz. It belongs to the STM32G0 series, designed for cost-sensitive and energy-efficient embedded applications. This MCU integrates essential peripherals, memory, and system functions into a small package (8-pin SOIC), making it suitable for consumer electronics, industrial control, appliances, and IoT devices where space and power efficiency are critical. Key Features Core & Performance 32-bit Arm Cortex-M0+ CPU Up to 64 MHz clock frequency Memory Protection Unit (MPU) for improved reliability and security 💾 Memory 32 KB Flash memory (program storage) 8 KB SRAM Flash protection (read/write protection, secure area) Peripherals & Interfaces Communication: I2C (2x) SPI (2x) / I2S USART (2x) + Low-power UART 12-bit ADC (up to ~2.5 MSps, multiple channels) DMA controller (5 channels) Timers: Advanced PWM timer (motor control capable) General-purpose timers (16-bit & 32-bit) Low-power timers Watchdog timers RTC (Real-Time Clock) with VBAT backup Power & Efficiency Operating voltage: 1.7 V to 3.6 V Multiple low-power modes: Sleep, Stop, Standby, Shutdown Optimized for low energy consumption (battery-powered designs) I/O & Package Up to 44 GPIOs (depending on package) 6 GPIOs available in the 8-pin (J6M6) package 5V-tolerant I/O pins (select pins) Compact SOIC-8 package#commonpartslibrary #integratedcircuit #microcontroller

Buck Switching Regulator IC Positive Fixed 3.3V 1 Output 2A SOT-23-6 Thin, TSOT-23-6 The AP63200/AP63201/AP63203/AP63205 is a 2A, synchronous buck converter with a wide input voltage range of 3.8V to 32V and fully integrates a 125mΩ high-side power MOSFET and a 68mΩ low-side power MOSFET to provide high-efficiency step-down DC/DC conversion. The AP63200/AP63201/AP63203/AP63205 device is easily used by minimizing the external component count due to its adoption of peak current mode control along with its integrated compensation network. The AP63200/AP63201/AP63203/AP63205 has optimized designs for Electromagnetic Interference (EMI) reduction. The converter features Frequency Spread Spectrum (FSS) with a switching frequency jitter of ±6%, which reduces EMI by not allowing emitted energy to stay in any one frequency for a significant period of time. It also has a proprietary gate driver scheme to resist switching node ringing without sacrificing MOSFET turn-on and turn-off times, which further erases highfrequency radiated EMI noise caused by MOSFET switching. The device is available in a low-profile, TSOT26 package. • VIN 3.8V to 32V • 2A Continuous Output Current • 0.8V ±1% Reference Voltage • 22µA Ultralow Quiescent Current • Switching Frequency o 500kHz: AP63200 and AP63201 o 1.1MHz: AP63203 and AP63205 • Pulse Width Modulation (PWM) Regardless of Output Load o AP63201 • Supports Pulse Frequency Modulation (PFM) o AP63200, AP63203, and AP63205 o Up to 80% Efficiency at 1mA Light Load o Up to 88% Efficiency at 5mA Light Load • Fixed Output Voltage o 3.3V: AP63203 o 5.0V: AP63205 • Proprietary Gate Driver Design for Best EMI Reduction • Frequency Spread Spectrum (FSS) to Reduce EMI • Precision Enable Threshold to Adjust UVLO • Protection Circuitry o Overvoltage Protection o Cycle-by-Cycle Peak Current Limit o Thermal Shutdown • 12V and 24V distributed power bus supplies • Flat screen TV sets and monitors • Power tools and laser printers • White goods and small home appliances • FPGA, DSP, and ASIC supplies • Home audios • Network systems • Set top boxes • Gaming consoles • Consumer electronics #commonpartslibrary #integratedcircuit #AP63203WU7 #BuckConverter #DCDCConverter #PowerManagement #VoltageRegulator #SynchronousBuck #EmbeddedSystems #IndustrialElectronics #PowerSupply #DiodesInc #3V3Power #ElectronicsDesign

Bipolar (BJT) Transistor NPN 40V 200 mA 300MHz 625 mW Through Hole TO-92-3 The 2N3904TFR is a general-purpose NPN bipolar junction transistor (BJT) designed for low-power amplification and switching applications. It is widely used in signal processing, small-signal amplification, and digital switching circuits. This transistor offers fast switching speed, low saturation voltage, and reliable performance in a compact surface-mount package, making it suitable for consumer electronics, industrial controls, and embedded systems. Manufacturer Various (commonly ON Semiconductor / onsemi, Diodes Inc., Central Semiconductor) Part Number 2N3904TFR Transistor Type NPN Bipolar Junction Transistor (BJT) Configuration Single Package / Case SOT-23 (TO-236AB) Mounting Style Surface Mount (SMD/SMT) Collector-Emitter Voltage (VCEO) 40 V Collector-Base Voltage (VCBO) 60 V Emitter-Base Voltage (VEBO) 6 V Collector Current (IC) 200 mA (max) Power Dissipation (PD) ~200 mW to 350 mW (package dependent) DC Current Gain (hFE) 100 to 300 (typical, varies with operating conditions) Transition Frequency (fT) ~300 MHz Collector-Emitter Saturation Voltage (VCE(sat)) ~0.2 V (typical at IC = 10 mA, IB = 1 mA) Operating Temperature Range -55°C to +150°C Polarity NPN Packaging Tape & Reel (TFR suffix) RoHS Compliance Compliant #commonpartslibrary #transistor #bjt

PIC PIC® 16F Microcontroller IC 8-Bit 20MHz 14KB (8K x 14) FLASH 40-PDIP The PIC16F877A-I/P is a high-performance 8-bit microcontroller from Microchip Technology, based on a Harvard architecture with separate program and data memory buses. It is designed for a wide range of embedded applications requiring reliable processing, multiple communication interfaces, and analog capability. The device integrates Flash program memory, EEPROM data storage, and numerous peripherals including ADC, timers, serial communication modules, and PWM functions. Packaged in a 40-pin PDIP form factor, it is widely used in industrial automation, consumer electronics, and educational development systems. Core Features 8-bit PIC microcontroller architecture Harvard architecture with RISC instruction set Operating frequency up to 20 MHz Single-cycle instruction execution (except branches) Memory Program Memory: 8K words (Flash) Data Memory (RAM): 368 bytes EEPROM Data Memory: 256 bytes I/O Features Up to 33 programmable I/O pins Multiple input/output ports (PORTA, PORTB, PORTC, PORTD, PORTE) High current sink/source capability on selected pins Analog Features 10-bit Analog-to-Digital Converter (ADC) Up to 8 analog input channels Programmable voltage reference Timers and Control Three timers (Timer0, Timer1, Timer2) Capture/Compare/PWM (CCP) modules Watchdog Timer (WDT) Power-on Reset (POR) and Brown-out Reset (BOR) Communication Interfaces USART (Universal Synchronous/Asynchronous Receiver/Transmitter) SPI (Serial Peripheral Interface) I²C (Inter-Integrated Circuit) via MSSP module Electrical Characteristics Operating Voltage: 4.0V to 5.5V Operating Temperature Range: -40°C to +85°C (Industrial grade) Low power consumption modes available Package Information Package Type: PDIP (Plastic Dual Inline Package) Pin Count: 40 pins Mounting Type: Through-hole Applications Industrial control systems Embedded automation Consumer electronics Sensor interfacing and data acquisition Educational and prototyping platforms #commonpartslibrary #integratedcircuit #microcontroller

Buck Switching Regulator IC Positive Fixed 5V 1 Output 1A SOT-23-6 The LMR50410Y5FQDBVRQ1 (part of the LMR50410-Q1 family from Texas Instruments) is a synchronous step-down (buck) DC-DC converter designed for automotive and industrial power applications. It operates over a wide input voltage range of 4 V to 36 V and can deliver up to 1 A output current, making it suitable for converting higher, unregulated voltages into stable lower voltages (e.g., 5 V or 3.3 V rails). The device integrates power switches, control circuitry, and compensation internally, allowing simple design with minimal external components and a compact PCB footprint. Key Features Power & Performance Wide input voltage range: 4 V to 36 V Output current: up to 1 A High switching frequency: 2.1 MHz (enables small inductors) High efficiency with PFM (light load) and FPWM (constant frequency) options Integration & Ease of Use Synchronous rectification (integrated high-side & low-side MOSFETs) Internal compensation (no complex external tuning) Minimal external components required Small SOT-23-6 package for compact designs Protection & Reliability Cycle-by-cycle current limit Short-circuit protection (hiccup mode) Thermal shutdown protection Undervoltage lockout (UVLO) ±1% reference voltage accuracy Automotive & Industrial Capability AEC-Q100 qualified (automotive grade) Operating temperature: Ambient: up to 125°C Junction: up to 150°C Designed for rugged automotive environments Additional Features Soft-start for controlled startup Precision enable pin for system control Monotonic startup with pre-biased output Available in fixed output (e.g., 5 V) variants Typical Applications Automotive electronics (ADAS, infotainment, lighting) Industrial power supplies Distributed power systems General-purpose DC-DC regulation #commonpartslibrary #integratedcircuit #powermanagement #voltageregulator

The TPS6213x series, manufactured by Texas Instruments, includes highly efficient, easy-to-use synchronous step-down DC-DC converters optimized for applications requiring high power density. These converters operate within a wide input voltage range from 3 V to 17 V and are capable of delivering up to 3 A of continuous output current. The series comprises multiple part numbers, namely TPS62130, TPS62130A, TPS62131, TPS62132, and TPS62133, each offering unique output configurations—adjustable outputs for TPS62130 and TPS62130A, and fixed outputs of 1.8 V, 3.3 V, and 5.0 V for TPS62131, TPS62132, and TPS62133 respectively. Key features of the TPS6213x series include the advanced DCS-Control™ topology for improved transient response and high output voltage accuracy, a programmable soft start, seamless transition to power save mode, and selectable operating frequency (either 1.25 MHz or 2.5 MHz). The device also encapsulates robust protection mechanisms such as short circuit and overtemperature protection. Housed in a compact 3-mm x 3-mm QFN-16 package, the IC includes additional functions like a power-good output and 100% duty cycle mode for low dropout conditions. With a highly integrated design that requires minimal external components, the TPS6213x series is ideal for step-down regulation in various applications including standard 12-V rail supplies, POL supplies, embedded systems, and portable devices.

Bipolar (BJT) Transistor NPN 40V 600 mA 300MHz 300 mW Surface Mount SOT-23-3 (TO-236) The MMBT2222ALT3G is a NPN general-purpose bipolar junction transistor (BJT) manufactured by onsemi, designed in a SOT-23 surface-mount package. It is the SMD version of the well-known 2N2222A transistor family, used for switching and signal amplification in compact electronic circuits. It is widely used in industrial, automotive (AEC-Q101 qualified variants), and general embedded systems due to its reliability, small size, and good electrical performance. Key Features NPN General-Purpose Transistor Suitable for switching and low-power amplification Collector-Emitter Voltage (Vceo) Up to 40 V Collector Current Up to 600 mA Power Dissipation Around 225–300 mW (depending on package conditions) High Frequency Performance Transition frequency up to ~300 MHz DC Current Gain (hFE) Typically ~100 at moderate currents Low Saturation Voltage Efficient switching performance for digital circuits SOT-23 Surface-Mount Package Compact footprint for modern PCB designs Wide Temperature Range Typically -55°C to +150°C RoHS / Lead-Free Compliant Environmentally compliant manufacturing Typical Applications LED switching circuits Relay driver stages MCU signal interfacing (Arduino, ESP32, etc.) Small motor drivers General signal amplification Automotive and industrial control circuits Important Note MMBT2222ALT3G = SMD version (SOT-23) Equivalent to 2N2222A (TO-92 through-hole version) in function, but not in physical package. 2N2222A SOT-23 #commonpartslibrary #transistor #bjt

Automotive 5.5V to 36V, 500kHz Fixed Frequency 3A Buck Converter 8-SO PowerPAD -40 to 125 8-PowerSOIC (0.154", 3.90mm Width) #CommonPartsLibrary #IntegratedCircuit #PowerManagement #Voltage-Regulator #Switching-Regulator

TPS61088RHLR — Texas Instruments 10-A synchronous boost converter in RHL 20-pin VQFN package with exposed thermal pad. PCB footprint uses 21 pads: 20 perimeter terminals plus the exposed PGND thermal pad. Features 2.7 V to 12 V input, 4.5 V to 12.6 V adjustable output, 200 kHz to 2.2 MHz programmable switching frequency, programmable soft start, adjustable switch peak-current limit, 13.2 V output overvoltage protection, cycle-by-cycle overcurrent protection, and thermal shutdown. #commonpartslibrary #integratedcircuit #powermanagement #voltageregulator

Buck Switching Regulator IC Positive Adjustable 1.8V 1 Output 750mA 8-VFDFN The TPS62840 is a high-efficiency step-down converter with ultra-low operating quiescent current of typically 60 nA. The device contains special circuitry to achieve just 120 nA IQ in 100% mode to further extend battery life near the end of discharge. The device uses DCS-Control to cleanly power radios and operates with a typical switching frequency of 1.8 MHz. In Power-Save Mode, the device extends the light load efficiency down to a load current range of 1 μA and below. 16 predefined output voltages can be selected by connecting a resistor to pin VSET, making the device flexible for various applications with a minimum amount of external components. The STOP pin of the device immediately eliminates any switching noise in order to take a noise-free measurement in test and measurement systems. The TPS62840 provides an output current of up to 750 mA. With an input voltage of 1.8 V to 6.5 V, the device supports multiple power sources such as 2S to 4S Alkaline, 1S to 2S Li-MnO2 , or 1S Li-Ion/LiSOCl2 Features 1• 60-nA operating quiescent current • 100% duty-cycle mode with 120-nA IQ • Input voltage range VIN from 1.8 V to 6.5 V • Output current up to 750 mA • RF friendly DCS-Control™ • 80% efficiency at 1 µA IOUT (3.6 VIN to 1.8 VOUT) • 16 selectable output voltages via VSET pin • Auto transition PFM/PWM or forced-PWM mode • Selectable forced PWM and STOP modes • Output discharge function • 25-nA shutdown current #commonpartslibrary #integratedcircuit #powermanagement #voltageregulator

ESP32-S3-MINI-1-N8 is a compact, low-power Wi-Fi and Bluetooth module from Espressif Systems based on the ESP32-S3 SoC. It integrates a dual-core Xtensa LX7 processor, 8 MB flash memory, crystal oscillator, RF matching circuitry, and a PCB antenna in a small SMD package, making it ideal for IoT devices, smart home products, industrial automation, HMI applications, AIoT edge devices, and USB-connected embedded systems. Key Features Dual-core 32-bit Xtensa LX7 CPU Up to 240 MHz operating frequency Includes single-precision floating-point unit (FPU) for enhanced processing performance. Integrated Memory 8 MB Quad SPI Flash (N8 variant) 512 KB SRAM 384 KB ROM 16 KB RTC SRAM. Wireless Connectivity 2.4 GHz Wi-Fi 4 (802.11 b/g/n) Data rates up to 150 Mbps Bluetooth 5 LE with Bluetooth Mesh support Simultaneous Wi-Fi and Bluetooth operation through an integrated coexistence mechanism. Rich Peripheral Set Up to 39 GPIOs USB 2.0 OTG USB Serial/JTAG SPI, I²C, I²S, UART PWM, MCPWM SDIO Host ADC Touch sensing Temperature sensor TWAI® (CAN 2.0 compatible) Timers and watchdogs. Integrated Components On-board 40 MHz crystal oscillator PCB antenna RF matching network Compact certified module design. Operating Conditions Supply voltage: 3.0 V to 3.6 V Operating temperature: −40°C to +85°C. Compliance RoHS and REACH compliant RF-certified module for simplified product development. #RF_transceiver #Module #Esp32

3.8-V to 36-V, 3-A synchronous step-down voltage converter Buck Switching Regulator IC Positive Adjustable 1V 1 Output 3A 12-PowerVFQFN The LMR33630-Q1 automotive-qualified regulator is an easy-to-use, synchronous, step-down DC/DC converter that delivers best-in-class efficiency for rugged applications. The LMR33630-Q1 drives up to 3 A of load current from an input of up to 36 V. The LMR33630-Q1 provides high light load efficiency and output accuracy in a very small solution size. Features such as a power-good flag and precision enable provide both flexible and easy-touse solutions for a wide range of applications. The LMR33630-Q1 automatically folds back frequency at light load to improve efficiency. Integration eliminates most external components and provides a pinout designed for simple PCB layout. Protection features include thermal shutdown, input undervoltage lockout, cycle-by-cycle current limit, and hiccup short-circuit protection. The LMR33630-Q1 is available in a 12-pin 3 mm × 2 mm next generation VQFN package with wettable flanks • AEC-Q100 qualified for automotive applications: – Temperature grade 1: –40°C to +125°C, TA • Functional Safety-Capable – Documentation available to aid functional safety system design • Configured for rugged automotive applications – Input voltage range: 3.8 V to 36 V – Output voltage range: 1 V to 24 V – Output current: 3 A – 75-mΩ/50-mΩ RDS-ON power MOSFETs – Peak-current-mode control – Short minimum on-time of 68 ns – Frequency: 400 kHz, 1.4 MHz, 2.1 MHz – Integrated compensation network • Low EMI and switching noise – HotRod™ package – Parallel input current paths • High power conversion at all loads – Peak efficiency > 95% – Low shutdown quiescent current of 5 µA – Low operating quiescent current of 25 µA #CommonPartsLibrary #IntegratedCircuit #PowerManagement #LMR33630

3x Frequency Multiplier, output 300 to 450 MHz, 50 Ohm, Mini-Circuits TT1224, 6-SMD #commonpartslibrary #RF #integratedcircuit

5.025GHz Center Frequency Band Pass RF Filter (Radio Frequency) 9.95GHz Bandwidth 2dB 6-SMD, Flat Leads #commonpartslibrary #RF #integratedcircuit

LED Driver IC 16 Output Linear PWM Dimming 25mA 5.5V 28-TSSOP PCA9685PW,118 is a 16-channel, 12-bit PWM LED controller with an I²C interface designed for LED dimming, RGB/RGBA lighting, and servo motor control applications. It provides independent PWM control for up to 16 outputs, allowing precise brightness or position control while minimizing MCU GPIO usage. The device supports Fast-mode Plus I²C communication up to 1 MHz and operates from a 2.3 V to 5.5 V supply range. It is commonly used in robotics, LED backlighting, automation systems, and PWM expansion modules for microcontrollers such as Arduino, ESP32, and Raspberry Pi. Key Features 16 independent PWM output channels 12-bit PWM resolution (4096 steps) Programmable PWM frequency from approximately 24 Hz to 1526 Hz I²C Fast-mode Plus compatible interface up to 1 MHz Six hardware address pins allowing up to 62 devices on one I²C bus Programmable open-drain or totem-pole outputs Output capability: 25 mA sink current 10 mA source current Internal 25 MHz oscillator with optional external clock input Individual programmable LED ON/OFF timing for reduced EMI and current surges Supports software reset and group addressing (All Call/Sub Call) 5.5 V tolerant inputs and outputs Operating voltage range: 2.3 V to 5.5 V Package: 28-pin TSSOP (PW suffix) #CommonPartsLibrary #IntegratedCircuit #PowerManagement #LEDdriver

20 Hz ~ 20 kHz Analog Microphone Electret Condenser 3 V ~ 10 V Omnidirectional (-44dB ±2dB) PC Pins JLI 140A HD microphone microphone capsule The CMA-4544PF-W is an electret condenser microphone designed for compact audio capture applications. It features high sensitivity, low noise characteristics, and stable frequency response, making it suitable for voice recording, communication devices, and embedded audio systems. The device integrates a permanently charged electret diaphragm with a built-in FET preamplifier, enabling reliable signal output with minimal external circuitry. Key Features Electret condenser microphone element High sensitivity and signal-to-noise ratio Omnidirectional pickup pattern Compact, low-profile package Built-in FET impedance converter Stable performance over temperature range RoHS compliant Electrical Characteristics Operating Voltage: typically 2.0 V (range: 1.5 V to 10 V) Current Consumption: typically 0.5 mA Sensitivity: typically -44 dB ±3 dB (at 1 kHz, 0 dB = 1 V/Pa) Signal-to-Noise Ratio: typically 60 dB Output Impedance: typically 2.2 kΩ Frequency Response: 20 Hz to 16 kHz Acoustic Characteristics Directivity: Omnidirectional Maximum Sound Pressure Level: typically 110 dB SPL Equivalent Noise Level: typically 34 dB SPL Mechanical Characteristics Package Type: Through-hole cylindrical metal can Dimensions: approximately 4.5 mm diameter × 4.4 mm height Mounting Type: PCB through-hole Terminal Configuration: Two-pin (signal and ground) Environmental Specifications Operating Temperature Range: -20°C to +70°C Storage Temperature Range: -40°C to +85°C Applications Voice recording devices Mobile and handheld electronics Intercom and communication systems Embedded audio input modules IoT and consumer electronics Pin Configuration Pin 1: Output (Vout) Pin 2: Ground (GND / Case) Compliance RoHS compliant Suitable for general consumer electronics use #commonpartslibrary #audio #microphone #analog #condenser

Wio-E5 Dev Kit embedded with Wio-E5 STM32WLE5JC LoRa module that supports Long Range protocol on the global frequency band. It provides full GPIOs, which support various data protocols and interfaces such as RS485, Grove, male/female headers, etc. This makes it user-friendly because it allows for easy and flexible connections to other devices or components. It would be a perfect choice for fast testing and rapid prototyping of your Long Range IoT projects.

ARM® Cortex®-M4 series Microcontroller IC 32-Bit Single-Core 168MHz 1MB (1M x 8) FLASH 64-LQFP (10x10) Arm® Cortex®-M4 32b MCU+FPU, 210DMIPS, up to 1MB flash/192+4KB RAM, USB OTG HS/FS, Ethernet, 17 TIMs, 3 ADCs, 15 comm. interfaces, and camera Includes ST state-of-the-art patented technology • Core: Arm® 32-bit Cortex®-M4 CPU with FPU, Adaptive real-time accelerator (ART Accelerator) allowing 0-wait state execution from flash memory, frequency up to 168 MHz, memory protection unit, 210 DMIPS/ 1.25 DMIPS/MHz (Dhrystone 2.1), and DSP instructions • Memories – Up to 1 Mbyte of flash memory – Up to 192+4 Kbytes of SRAM including 64- Kbyte of CCM (core coupled memory) data RAM – 512 bytes of OTP memory – Flexible static memory controller supporting CompactFlash™, SRAM, PSRAM, NOR and NAND memories • LCD parallel interface, 8080/6800 modes • Clock, reset, and supply management – 1.8 V to 3.6 V application supply and I/Os – POR, PDR, PVD and BOR – 4-to-26 MHz crystal oscillator – Internal 16 MHz factory-trimmed RC (1% accuracy) – 32 kHz oscillator for RTC with calibration – Internal 32 kHz RC with calibration • Low-power operation – Sleep, Stop, and Standby modes –VBAT supply for RTC, 20×32-bit backup registers + optional 4 KB backup SRAM • 3×12-bit, 2.4 MSPS A/D converters: up to 24 channels and 7.2 MSPS in triple interleaved mode • 2×12-bit D/A converters • General-purpose DMA: 16-stream DMA controller with FIFOs and burst support • Up to 17 timers: up to twelve 16-bit and two 32- bit timers up to 168 MHz, each with up to 4 IC/OC/PWM or pulse counter and quadrature (incremental) encoder input • Debug mode – Serial wire debug (SWD) & JTAG interfaces – Cortex-M4 Embedded Trace Macrocell™ • Up to 140 I/O ports with interrupt capability – Up to 136 fast I/Os up to 84 MHz – Up to 138 5 V-tolerant I/Os • Up to 15 communication interfaces – Up to 3 × I2C interfaces (SMBus/PMBus) – Up to 4 USARTs/2 UARTs (10.5 Mbit/s, ISO 7816 interface, LIN, IrDA, modem control) – Up to 3 SPIs (42 Mbits/s), 2 with muxed full-duplex I2S to achieve audio class accuracy via internal audio PLL or external clock – 2 × CAN interfaces (2.0B Active) – SDIO interface • Advanced connectivity – USB 2.0 full-speed device/host/OTG controller with on-chip PHY – USB 2.0 high-speed/full-speed device/host/OTG controller with dedicated DMA, on-chip full-speed PHY and ULPI – 10/100 Ethernet MAC with dedicated DMA: supports IEEE 1588v2 hardware, MII/RMII #commonpartslibrary #integratedcircuit #microcontroller

5.025GHz Center Frequency Band Pass RF Filter (Radio Frequency) 9.95GHz Bandwidth 2dB 6-SMD, Flat Leads #commonpartslibrary #RF #integratedcircuit

555 Type, Timer/Oscillator (Single) IC 2.1MHz 8-SOIC The TLC555IDR is a low-power CMOS timer device designed as a functional replacement for the standard bipolar 555 timer while providing significantly reduced supply current and improved operating efficiency. The device supports both astable and monostable operating modes and is commonly used for timing generation, pulse shaping, oscillation, PWM generation, delay circuits, and frequency generation applications. The CMOS architecture enables low power consumption, rail-to-rail output capability, and stable timing performance over a wide operating voltage range. The device is suitable for battery-powered systems, portable electronics, industrial controls, instrumentation, consumer products, and embedded electronic designs. The TLC555IDR is supplied in a compact SOIC surface-mount package intended for automated PCB assembly and space-constrained applications. Electrical Characteristics CMOS low-power timer architecture Functional equivalent to standard 555 timer devices Wide operating supply voltage range Low quiescent supply current High input impedance Rail-to-rail output swing capability Stable threshold and trigger levels Compatible with TTL and CMOS logic levels Capable of astable and monostable operation Adjustable duty cycle and frequency operation High output drive capability for direct interfacing Low noise and improved switching performance compared to bipolar 555 timers Functional Features Precision timing generation Oscillator and clock generation Pulse-width modulation support One-shot pulse generation Delay timer implementation Missing pulse detection Frequency divider implementation Sequential timing control LED flashing and tone generation PWM motor and power control applications Package Information Surface-mount SOIC package Standard tape-and-reel packaging format Compact footprint for automated assembly RoHS compliant device construction Environmental and Operating Conditions Industrial operating temperature range ESD protection handling required Suitable for commercial and industrial embedded systems Designed for low-power electronic applications Typical Applications Timer circuits Pulse generators Oscillators PWM controllers LED flashers Alarm and tone generators Frequency generators Power management timing Embedded control systems Portable battery-powered electronics #commonpartslibrary #integratedcircuit #timer #oscillator

RF IC Frequency Multiplier General Purpose 20MHz ~ 1GHz #commonpartslibrary #RF #integratedcircuit

CH32V003 is an industrial-grade microcontroller with a 48MHz main frequency, low power consumption, small size, and built-in DMA controllers, ADC, timers, and communication interfaces. #RISC-V #IoT #MCU