USB-C Receptacle with built-in ESD Protection and 3V3 LDO Voltage Regulator. This is reusable to any of your projects.

Linear Voltage Regulator IC Positive Fixed 1 Output 600mA SOT-25 3.3V LDO AP2112K-3.3 The AP2112K-3.3TRG1 is a low dropout (LDO) linear voltage regulator designed to provide a stable 3.3V output from a higher input voltage. It is optimized for low noise, high power supply rejection ratio (PSRR), and low quiescent current, making it suitable for battery-powered and noise-sensitive applications. The device features current limiting and thermal shutdown protection, ensuring reliable operation under fault conditions. It is commonly used in portable electronics, RF modules, microcontroller power supplies, and other low-power systems. Key Features Fixed output voltage: 3.3V Output current: up to 600 mA Low dropout voltage: ~250 mV at 300 mA load High PSRR: up to 70 dB at 1 kHz Low quiescent current: typically 55 µA Stable with low ESR ceramic capacitors Built-in overcurrent protection Thermal shutdown protection Fast transient response Absolute Maximum Ratings Input Voltage (VIN): up to 6.5 V Output Current: Internally limited Operating Junction Temperature: -40°C to +125°C Storage Temperature: -65°C to +150°C Electrical Characteristics (Typical values unless otherwise specified) Output Voltage Accuracy: ±2% Dropout Voltage: 250 mV @ 300 mA 400 mV @ 600 mA Line Regulation: 0.05%/V Load Regulation: 0.2% Quiescent Current: 55 µA Shutdown Current: <1 µA PSRR: 70 dB @ 1 kHz 45 dB @ 10 kHz Pin Configuration (SOT-23-5 / SC-70-5) VIN – Input voltage GND – Ground EN – Enable (active high) NC – No connection VOUT – Regulated output (3.3V) Package Information Package Type: SOT-23-5 (TRG1 suffix indicates tape & reel) Mounting: Surface mount Small footprint suitable for compact PCB layouts Typical Applications Battery-powered devices Wireless modules (Wi-Fi, Bluetooth, RF) Microcontroller and FPGA power supplies Portable consumer electronics Sensor and analog circuits requiring low noise Compliance & Reliability RoHS compliant Lead-free package Designed for high reliability and long operational life #CommonPartsLibrary #IntegratedCircuit #PowerManagement #LinearRegulator #VoltageRegulator

USB-C (USB TYPE-C) USB 2.0 Receptacle Connector 24 (16+8 Dummy) Position Surface Mount, Right Angle; Through Hole The USB4105-GF-A is a USB Type-C receptacle connector designed for USB 2.0 applications, commonly used in embedded systems, IoT devices, and consumer electronics. It features a 24-position (16 active + 8 dummy) contact design that supports reversible plug orientation, making it user-friendly and compliant with USB Type-C standards. This connector is a right-angle, surface-mount (SMT) device with through-hole retention tabs, providing both compact PCB integration and strong mechanical stability. Key Features USB Type-C Interface Reversible plug orientation (no wrong insertion) Standard USB Type-C receptacle Supports USB 2.0 signaling Contact Configuration 24 pins total (16 active + 8 dummy pins) Includes: Power (VBUS) Ground (GND) USB 2.0 data (D+, D−) Configuration channel (CC) Electrical Capability Supports multiple current levels (up to 5A depending on design) Rated voltage up to 48V DC Mechanical Design Right-angle (horizontal) mounting Surface-mount + through-hole hybrid Includes: Board guide Solder retention tabs (strong anchoring) Durability & Materials Shielded metal shell (EMI protection) Contact finish: Gold plating Housing: UL94 V-0 flame rated Mating cycles: ~20,000 insertions Environmental Specs Operating temperature: -40°C to +85°C RoHS compliant (lead-free) Typical Applications Microcontroller boards (ESP32, Arduino, etc.) Charging + data interface for embedded devices Power + USB communication ports Consumer electronics (gadgets, accessories) #CommonPartsLibrary #Connector #USB #DVI #USB4105 #USB-C

17V Clamp 5A (8/20µs) Ipp Tvs Diode Surface Mount SOT-666 The USBLC6-2SC6 and USBLC6-2P6 are monolithic application specific devices dedicated to ESD protection of high speed interfaces, such as USB 2.0, Ethernet links and video lines.

Electronic Fuse Regulator 5.3A 20-WQFN (3x4) The TPS25940LRVCR is a compact eFuse (electronic fuse) power management IC from Texas Instruments designed to provide advanced power-path protection and load management for systems such as SSDs, servers, storage devices, and embedded electronics. It integrates protection features like overcurrent limiting, reverse current blocking, overvoltage protection, and controlled startup sequencing into a single chip. Wide input voltage range: 2.7 V to 18 V Adjustable current limit: 0.6 A to 5.3 A Low ON resistance: 42 mΩ typical True reverse current blocking using back-to-back MOSFETs Programmable output slew rate (dV/dt control) for inrush current management Overvoltage and undervoltage protection Fault and Power-Good outputs for system monitoring Current monitor (IMON) output Low-power DevSleep support for SSD applications Fast reverse voltage shutdown (~1 µs) Operating temperature: −40°C to +125°C junction temperature Available in a compact 20-pin WQFN package Typical Applications PCIe / SATA / SAS SSDs and HDDs Enterprise servers and storage systems RAID controller cards Smart load switches Set-top boxes and gaming systems Backup power and holdup capacitor systems Component Category This component belongs to: Power Management IC (PMIC) More specifically: eFuse / Hot-swap / Load Switch IC Package Information Package type: 20-WQFN (3 mm × 4 mm) Mounting type: Surface Mount (SMD) #commonpartslibrary #integratedcircuit #powermanagement #currentregulation

Buck Switching Regulator IC Positive Fixed 3.3V 1 Output 2A SOT-23-6 Thin, TSOT-23-6 The AP63200/AP63201/AP63203/AP63205 is a 2A, synchronous buck converter with a wide input voltage range of 3.8V to 32V and fully integrates a 125mΩ high-side power MOSFET and a 68mΩ low-side power MOSFET to provide high-efficiency step-down DC/DC conversion. The AP63200/AP63201/AP63203/AP63205 device is easily used by minimizing the external component count due to its adoption of peak current mode control along with its integrated compensation network. The AP63200/AP63201/AP63203/AP63205 has optimized designs for Electromagnetic Interference (EMI) reduction. The converter features Frequency Spread Spectrum (FSS) with a switching frequency jitter of ±6%, which reduces EMI by not allowing emitted energy to stay in any one frequency for a significant period of time. It also has a proprietary gate driver scheme to resist switching node ringing without sacrificing MOSFET turn-on and turn-off times, which further erases highfrequency radiated EMI noise caused by MOSFET switching. The device is available in a low-profile, TSOT26 package. • VIN 3.8V to 32V • 2A Continuous Output Current • 0.8V ±1% Reference Voltage • 22µA Ultralow Quiescent Current • Switching Frequency o 500kHz: AP63200 and AP63201 o 1.1MHz: AP63203 and AP63205 • Pulse Width Modulation (PWM) Regardless of Output Load o AP63201 • Supports Pulse Frequency Modulation (PFM) o AP63200, AP63203, and AP63205 o Up to 80% Efficiency at 1mA Light Load o Up to 88% Efficiency at 5mA Light Load • Fixed Output Voltage o 3.3V: AP63203 o 5.0V: AP63205 • Proprietary Gate Driver Design for Best EMI Reduction • Frequency Spread Spectrum (FSS) to Reduce EMI • Precision Enable Threshold to Adjust UVLO • Protection Circuitry o Overvoltage Protection o Cycle-by-Cycle Peak Current Limit o Thermal Shutdown • 12V and 24V distributed power bus supplies • Flat screen TV sets and monitors • Power tools and laser printers • White goods and small home appliances • FPGA, DSP, and ASIC supplies • Home audios • Network systems • Set top boxes • Gaming consoles • Consumer electronics #commonpartslibrary #integratedcircuit #AP63203WU7 #BuckConverter #DCDCConverter #PowerManagement #VoltageRegulator #SynchronousBuck #EmbeddedSystems #IndustrialElectronics #PowerSupply #DiodesInc #3V3Power #ElectronicsDesign

Fuse Holder 32V 1 Circuit Blade Through Hole The 178.6764.0001 is an automotive blade fuse holder from Littelfuse, part of the MINI® FL1 series, designed for direct PCB mounting (through-hole). It allows easy integration of a single MINI blade fuse into a printed circuit board for overcurrent protection. This component is commonly used in automotive electronics, industrial control systems, and embedded power circuits, where compact and reliable fuse protection is required. Key Features Fuse Type Compatibility Supports MINI® automotive blade fuses (ATM/APM type) PCB Mount (Through-Hole) Designed for direct soldering to PCB for strong mechanical support Current Capability Up to 30 A maximum ~22 A continuous rating Voltage Rating Up to 58 VDC (automotive systems) Single Fuse Position Holds 1 fuse per holder Thermoplastic Housing Heat-resistant black body UL94 V-0 flammability rating for safety Contact Material Tin-plated copper alloy terminals for reliable conductivity Standard PCB Pitch Approx. 7.62 mm pin spacing Modular Design Multiple holders can be mounted side-by-side for multi-channel protection blade fuse holder automotive PCB #Circuit-Protection #Fuseholders #FL1

MAX98357A Series 5.5V 3.2W PCM Input Class D Audio Power Amplifier - TQFN-16 The MAX98357A/MAX98357B is an easy-to-use, low-cost, digital pulse-code modulation (PCM) input Class D amplifier that provides industry-leading Class AB audio performance with Class D efficiency. The digital audio interface automatically recognizes up to 35 different PCM and TDM clocking schemes which eliminates the need for I2C programming. Operation is further simplified by eliminating the need for an external MCLK signal that is typically used for PCM communication. Simply supply power, LRCLK, BCLK, and digital audio to generate audio! Furthermore, a novel pinout allows customers to use the cost-effective WLP package with no need for expensive vias (refer to Application Note 6643: Optimize Cost, Size, and Performance with MAX98357 WLP for more information). The digital audio interface is highly flexible with the MAX98357A supporting I2S data and the MAX98357B supporting left-justified data. Both ICs support 8 channel time division multiplexed (TDM) data. The digital audio interface accepts specified sample rates between 8kHz and 96kHz for all supported data formats. The ICs can be configured to produce a left channel, right channel, or (left/2 + right/2) output from the stereo input data. The ICs operate using 16/24/32-bit data for I2S and left-justified modes as well as 16-bit or 32-bit data using TDM mode. The ICs eliminate the need for the external MCLK signal that is typically used for PCM communication. This reduces EMI and possible board coupling issues in addition to reducing the size and pin count of the ICs. The ICs also feature a very high wideband jitter tolerance (12ns typ) on BCLK and LRCLK to provide robust operation. Active emissions-limiting, edge-rate limiting, and overshoot control circuitry greatly reduce EMI. A filterless spread-spectrum modulation scheme eliminates the need for output filtering found in traditional Class D devices and reduces the component count of the solution. The ICs are available in 9-pin WLP (1.345mm x 1.435mm x 0.64mm) and 16-pin TQFN (3mm x 3mm x 0.75mm) packages and are specified over the -40°C to +85°C temperature range. ● Single-Supply Operation (2.5V to 5.5V) ● 3.2W Output Power into 4Ω at 5V ● 2.4mA Quiescent Current ● 92% Efficiency (RL = 8Ω, POUT = 1W) ● 22.8μVRMS Output Noise (AV = 15dB) ● Low 0.013% THD+N at 1kHz ● No MCLK Required ● Sample Rates of 8kHz to 96kHz ● Supports Left, Right, or (Left/2 + Right/2) Output ● Sophisticated Edge Rate Control Enables Filterless Class D Outputs ● 77dB PSRR at 1kHz ● Low RF Susceptibility Rejects TDMA Noise from GSM Radios ● Extensive Click-and-Pop Reduction Circuitry ● Robust Short-Circuit and Thermal Protection ● Available in Space-Saving Packages: 1.345mm x 1.435mm WLP (0.4mm Pitch) and 3mm x 3mm TQFN ● Solution Size with Single Bypass Capacitor is 4.32mm2 Applications ● Single Li-ion Cell/5V Devices ● Smart Speakers ● Notebook Computers ● IoT Devices ● Gaming Devices (Audio and Haptics) ● Smartphones ● Tablets ● Cameras #commonpartslibrary #integratedcircuit #linearamplifier #mono

Buck Switching Regulator IC Positive Fixed 5V 1 Output 1A SOT-23-6 The LMR50410Y5FQDBVRQ1 (part of the LMR50410-Q1 family from Texas Instruments) is a synchronous step-down (buck) DC-DC converter designed for automotive and industrial power applications. It operates over a wide input voltage range of 4 V to 36 V and can deliver up to 1 A output current, making it suitable for converting higher, unregulated voltages into stable lower voltages (e.g., 5 V or 3.3 V rails). The device integrates power switches, control circuitry, and compensation internally, allowing simple design with minimal external components and a compact PCB footprint. Key Features Power & Performance Wide input voltage range: 4 V to 36 V Output current: up to 1 A High switching frequency: 2.1 MHz (enables small inductors) High efficiency with PFM (light load) and FPWM (constant frequency) options Integration & Ease of Use Synchronous rectification (integrated high-side & low-side MOSFETs) Internal compensation (no complex external tuning) Minimal external components required Small SOT-23-6 package for compact designs Protection & Reliability Cycle-by-cycle current limit Short-circuit protection (hiccup mode) Thermal shutdown protection Undervoltage lockout (UVLO) ±1% reference voltage accuracy Automotive & Industrial Capability AEC-Q100 qualified (automotive grade) Operating temperature: Ambient: up to 125°C Junction: up to 150°C Designed for rugged automotive environments Additional Features Soft-start for controlled startup Precision enable pin for system control Monotonic startup with pre-biased output Available in fixed output (e.g., 5 V) variants Typical Applications Automotive electronics (ADAS, infotainment, lighting) Industrial power supplies Distributed power systems General-purpose DC-DC regulation #commonpartslibrary #integratedcircuit #powermanagement #voltageregulator

2.7 - 5.7 V, 4 A, 31-m True Reverse Current Blocking eFuse with Input Reverse Polarity Protection #CommonPartsLibrary #IntegratedCircuit #PowerManagement #Current-regulation #TPS25210

1.5A USB-Friendly Li-Ion Battery Charger and Power-Path Management IC with 4.2 VBAT The BQ24075TRGTR (from Texas Instruments) is a highly integrated single-cell Li-Ion / Li-Polymer linear battery charger IC with power-path management. It is designed for portable and space-constrained applications, allowing a device to be powered from a USB port or AC adapter while simultaneously charging the battery. The device integrates charging control, power-path management, and safety features into a compact package. A key feature is its Dynamic Power Path Management (DPPM), which ensures the system is powered even when the battery is low or absent, while intelligently managing charging current. Key Features Battery Charging Supports single-cell Li-Ion / Li-Polymer batteries Up to 1.5 A programmable charge current Three-phase charging: Pre-charge (conditioning) Constant current Constant voltage Fixed 4.2 V charge voltage Power Path Management Dynamic Power Path Management (DPPM): Powers system and charges battery simultaneously Prioritizes system load over charging Allows system operation even with: Deeply discharged battery No battery connected Input & Power Features Operates from: USB input (100 mA / 500 mA selectable) AC adapter Programmable input current limit up to 1.5 A Input voltage range: ~4.35 V to 6.4 V (28 V max rating) Input dynamic power management (VIN-DPM) prevents source overload Protection & Safety Thermal regulation and shutdown Over-voltage protection (OVP) Short-circuit and reverse current protection Battery temperature monitoring (NTC thermistor input) Battery disconnect (SYSOFF) feature Control & Status Standalone operation (no MCU required, resistor-programmable) Charge status outputs: Charging Charge complete Power good Physical Characteristics Package: 16-pin VQFN (3 mm × 3 mm) Operating temperature: –40°C to +85°C #commonpartslibrary #integratedcircuit #powermanagement #batterycharger

The TPS6213x series, manufactured by Texas Instruments, includes highly efficient, easy-to-use synchronous step-down DC-DC converters optimized for applications requiring high power density. These converters operate within a wide input voltage range from 3 V to 17 V and are capable of delivering up to 3 A of continuous output current. The series comprises multiple part numbers, namely TPS62130, TPS62130A, TPS62131, TPS62132, and TPS62133, each offering unique output configurations—adjustable outputs for TPS62130 and TPS62130A, and fixed outputs of 1.8 V, 3.3 V, and 5.0 V for TPS62131, TPS62132, and TPS62133 respectively. Key features of the TPS6213x series include the advanced DCS-Control™ topology for improved transient response and high output voltage accuracy, a programmable soft start, seamless transition to power save mode, and selectable operating frequency (either 1.25 MHz or 2.5 MHz). The device also encapsulates robust protection mechanisms such as short circuit and overtemperature protection. Housed in a compact 3-mm x 3-mm QFN-16 package, the IC includes additional functions like a power-good output and 100% duty cycle mode for low dropout conditions. With a highly integrated design that requires minimal external components, the TPS6213x series is ideal for step-down regulation in various applications including standard 12-V rail supplies, POL supplies, embedded systems, and portable devices.

Low capacitance unidirectional fivefold ESD protection diode array, 3.3V, Common Anode, SOT-363 diode SOT?363*

Polymeric PTC Resettable Fuse 60V 500 mA Ih Surface Mount 2-SMD 500mA resettable fuse pptc The SMD050F-2 is a surface-mount resettable fuse (PPTC – Polymer Positive Temperature Coefficient) designed to provide overcurrent protection in low-voltage electronic circuits. It operates by increasing its resistance significantly when excessive current flows, thereby limiting current and protecting downstream components. Once the fault condition is removed and the device cools, it automatically resets to its low-resistance state, enabling normal operation without replacement. This component is commonly used in power supply lines, USB ports, battery-powered devices, and general electronic protection applications where space-saving and reliability are important. Key Features Resettable overcurrent protection (self-recovering) Surface-mount package for compact PCB layouts Low resistance in normal operation Fast response to fault conditions Automatic reset after fault removal RoHS compliant and lead-free Electrical Characteristics Hold current: 0.5 A Trip current: 1.0 A (typical) Maximum voltage: 60 V Maximum current: 40 A (fault current rating) Initial resistance: low resistance range suitable for minimal voltage drop Resistance after trip: significantly increased to limit current Thermal Characteristics Operating temperature range: -40°C to +85°C Trip time dependent on applied current and ambient temperature Reset time dependent on cooling conditions Mechanical Characteristics Package type: Surface-mount (SMD) Compact footprint suitable for dense PCB layouts Compatible with standard reflow soldering processes Applications USB and peripheral port protection Power supply and DC line protection Battery pack protection Consumer electronics Industrial control circuits Compliance and Standards RoHS compliant Halogen-free (depending on manufacturer variant) Meets industry standards for resettable fuses #commonpartslibrary #circuitprotection #ptc #fuse