Battery Multi-Function Controller IC Lithium Ion/Polymer 32-VFQFPN (5x5) L9961 is part of a complete battery pack monitoring, balancing, and protecting system for Li-Ion and Li-Polymer cells in 3, 4 or 5 series configurations. The L9961 uses a high precision ADC to provide cell voltage, stack voltage and temperature conversion via external NTC. Voltage monitoring functions are cyclically performed with a programmable loop time. Stack current is also monitored via a high accuracy CSA, continuously running and performing also Coulomb counting. Cell balancing is available and can be simultaneously activated on all cells. IC configuration and information exchange for SOC/SOH estimation are performed via I2C peripheral. The IC also integrates a dual pre-driver programmable in both HS/LS configurations for driving pack relays. L9961 also implements battery pack fuse protection to prevent fire and explosion hazards. A 3.3 V regulator with a high current capability is available for supplying pack controller and other external circuitry in both standby and normal operation modes. The IC protects the battery pack against over/under voltage conditions and monitors for over/ under temperature. It also features protection against overcurrent (both directions) and short-circuit in discharge events. Safety-relevant configurations can be stored in the internal NVM to avoid re-programming the device at each wake-up. Features • 2 μA shipment - DEEP SLEEP mode current and 5 μA standby consumption (with VREG LDO active) standby consumption (with VREG LDO active) • Integrated 3.3 V VREG LDO for supplying MCU and LEDs • Measures cell voltage (3 to 5 cells), with over/undervoltage detection and balance undervoltage protection • 12-bit voltage measurement with maximum error of ±15 mV in the [1.5 – 4.5] V range, for -40 °C < TJ < 105 °C • Measures stack voltage, with over/under voltage detection and plausibility check vs. sum of cells • Measures pack temperature via NTC, with over/undertemperature detection • Ratiometric temperature measurement with ±0.8% max. gain error in the [0.2 – VREG] V range, for -40 °C < TJ < 105 °C • Measures battery current, with Coulomb counting, overcurrent (both directions) and short-circuit in discharge protection. • 16-bit signed current measurement with 0.1% full scale error at room temperature • I 2C peripheral for device programming and data transfers over I2C bus • Cell balancing supporting up to 70 mA per cell • Dual configurable HS/LS predriver for pack relay management • Pack fuse management • Embedded NVM for configuration parameters storage • High hotplug robustness Applications • Cordless power tools • Backup energy storage systems and UPS • Light electric vehicles (e-bikes, scooters, etc.) • Portable and semi-portable equipment • Medical equipment #L9961TR #BatteryManagement #BMS #LiIonBattery #LiPoBattery #STMicroelectronics #BatteryProtection #CellBalancing #CoulombCounting #PowerManagement #EmbeddedSystems #EnergyStorage #EBike #PowerTools #ElectronicsDesign

Battery Power Management IC Multi-Chemistry 14-TSSOP The bq34210-Q1 1-Series Cell System-Side CEDV Fuel Gauge provides fuel gauging and End-of-Service (EOS) Determination for 1-series cell batteries in applications that encounter infrequent discharge, such as eCall systems and uninterruptible power supplies (UPS) for backup during power failures, where batteries may stay connected to a charging power source most of their lifetime until needed. The bq34210-Q1 fuel gauge supports multiple battery chemistries, including Li-Ion, LiFePO4, and NiMH. The gas gauging function uses voltage, current, and temperature data along with Compensated End-ofDischarge (CEDV) technology to provide State-ofCharge (SOC) and State-of-Health (SOH) data. The device's EOS Determination function alerts when battery capability has degraded and is approaching the end of its usable service. Battery fuel gauging with the bq34210-Q1 fuel gauge requires connections only to PACK+ (P+) and PACK– (P–) for a removable battery pack or embedded battery management system. Features 1• Automotive-Qualified AEC-Q100, Grade 3 • 1-Series Cell Battery Fuel Gauge Supports Li-Ion, LiFePO4, and NiMH (3-Cell) Chemistries – Resides on System Board – Powers Directly from the Battery with Integrated LDO – Supports a Low-Value External Sense Resistor (10 mΩ) • Learning Load Enable (LEN) from Host • Ultra-Low Power Consumption in NORMAL (50 µA) and SLEEP (9 µA) Modes • Supports Replacement Batteries • Accurate End-of-Service (EOS) Determination for Batteries in Rarely Discharged Applications • CEDV Gas Gauge for 1-Series Cell Batteries, Providing: – State-of-Charge (SOC) – Time-to-Empty (TTE) – State-of-Health (SOH) • High-Side and Low-Side Current Sensing Options • Internal Temperature Sensor OR External Thermistor • Microcontroller Peripheral Interface Supports: – 400-kHz I 2C™ Serial Interface – Configurable Interrupt (ALERT) for SOC, Battery Levels, Temperature Faults, and Charge/Discharge Status 2 Applications • eCall Systems • Telematics Backup Systems • Uninterruptible Power Supply (UPS) Backup Systems • Emergency Battery Power Modules #BatteryFuelGauge #BatteryManagement #FuelGaugeIC #AutomotiveElectronics #TexasInstruments #LiIonBattery #LiFePO4 #I2C #PowerManagement #AECQ100 #BackupBattery #UPS #EmbeddedSystems

Battery Battery Protection IC Lithium Ion/Polymer SOT-23-6 S-8261ABJMD-G3JT2G is a high-accuracy lithium-ion/lithium-polymer battery protection IC designed for single-cell battery packs. It integrates voltage detection and timing circuits to protect rechargeable batteries against overcharge, overdischarge, overcurrent, and short-circuit conditions, helping improve battery safety, reliability, and lifespan. The device is commonly used in portable electronics, battery packs, IoT devices, and handheld equipment. It is housed in a compact SOT-23-6 package suitable for space-constrained designs. Key Features Single-cell Li-ion / Li-polymer battery protection IC High-accuracy overcharge detection High-accuracy overdischarge detection Overcurrent and short-circuit protection Built-in delay circuits to prevent false triggering Low current consumption (typical operating current in the µA range) Wide operating voltage range Support for 0 V battery charging function Compact SOT-23-6 package RoHS compliant and lead-free version available Typical Applications Li-ion battery packs Li-polymer battery packs Portable consumer electronics Wireless sensors and IoT devices Handheld instruments Rechargeable battery-powered equipment #BatteryProtectionIC #LiIonBattery #LiPoBattery #PowerManagement #BatteryPackProtection #OverchargeProtection #OverdischargeProtection #ShortCircuitProtection #SOT23 #ABLIC #SeikoInstruments #PortableElectronics #RechargeableBattery #PMIC #SingleCellBattery