MAX-M10 RF Receiver BeiDou, Galileo, GLONASS, GPS, GNSS 1.561GHz, 1.575GHz, 1.602GHz -167dBm 921.6kbps Not Included Module The MAX-M10S-00B is a professional-grade, ultra-low-power GNSS positioning module from u-blox based on the u-blox M10 platform. It is designed for battery-powered applications such as asset trackers, wearables, IoT devices, and navigation systems. The module supports simultaneous reception of multiple GNSS constellations, providing high positioning availability, fast acquisition times, and excellent sensitivity even in challenging urban or weak-signal environments. It integrates a TCXO, LNA, and SAW filter to improve RF performance while maintaining very low power consumption. Key Features Multi-constellation GNSS receiver: GPS Galileo GLONASS BeiDou QZSS SBAS support (WAAS, EGNOS, MSAS, GAGAN) Concurrent tracking of up to four GNSS constellations for improved position availability and accuracy. Ultra-low power consumption: Approximately 25 mW in continuous tracking mode, making it ideal for battery-powered devices. High RF sensitivity: Tracking sensitivity up to −167 dBm for reliable operation in weak-signal conditions. High positioning accuracy: Typical position accuracy of approximately 1.5 m CEP under suitable conditions. Navigation update rate: Up to 10 Hz for responsive tracking applications. Integrated RF front-end: Built-in LNA (Low Noise Amplifier) Built-in SAW filter Integrated TCXO for stable operation. Supports Assisted GNSS services: AssistNow Online AssistNow Offline AssistNow Autonomous CloudLocate support for low-power IoT positioning. Communication interfaces: UART I²C NMEA and UBX protocols supported. Wide operating temperature range: −40°C to +85°C. Supply voltage: 1.76 V to 3.6 V. Typical Applications Asset tracking devices Wearable electronics Fleet management systems Industrial IoT Smart meters Drone and robotics navigation Personal navigation devices Timing and synchronization systems Package Information Package Type: Surface-mount LCC module Dimensions: 9.7 mm × 10.1 mm × 2.5 mm (typical module size) #Commonpartslibrary #RF #Wireless #RFreceivers #MAXM10S #uBlox #GNSS #GPS #Galileo #GLONASS #BeiDou #QZSS #NavigationModule #GNSSModule #GPSTracking #AssetTracking #IoT #IndustrialIoT #WearableTech #FleetManagement #DroneNavigation #EmbeddedSystems #ElectronicsDesign #PCBDesign #HardwareEngineering #LowPowerDesign #LocationTracking #Geolocation #RFDesign #LNA #SMTModule

Connector Header Through Hole 18 position 0.100" (2.54mm) # TSW-118-07-G-S ## General Description The TSW-118-07-G-S is a through-hole board-to-board and wire-to-board interconnect header manufactured by Samtec. It belongs to the TSW series of standard terminal strip headers designed for reliable signal transmission in electronic assemblies, embedded systems, industrial controls, telecommunications equipment, instrumentation, and general-purpose printed circuit board applications. The component features precision-machined contacts, robust mechanical construction, and compatibility with a wide range of mating connectors. Its design supports secure electrical connections while maintaining excellent durability during repeated mating cycles and long-term operation in demanding environments. ## Key Features ### Mechanical Characteristics * Through-hole mounting configuration * Single-row terminal strip header design * Straight vertical orientation * Precision-machined contact system * High-reliability board-level interconnection ### Contact System * Gold-plated contact surface * Enhanced conductivity and signal integrity * Corrosion-resistant contact finish * Suitable for repeated insertion and removal cycles ### Electrical Characteristics * Low contact resistance * Reliable signal transmission * Suitable for low-power and signal-level applications * Stable electrical performance across operating conditions ### Material Construction * High-temperature thermoplastic insulator * Durable metallic contact structure * RoHS-compliant materials * Lead-free manufacturing compatibility ### Environmental Characteristics * Industrial-grade operating capability * Resistant to mechanical wear during mating cycles * Suitable for automated and manual assembly processes ### Application Areas * Embedded Systems * Microcontroller Development Boards * Industrial Automation Equipment * Telecommunications Hardware * Test and Measurement Instruments * Medical Electronics * Data Acquisition Systems * Prototyping Platforms * Consumer Electronic Devices * PCB Interconnection Applications ### Compliance * RoHS Compliant * Lead-Free Compatible * Industry-standard connector footprint ## Manufacturer Samtec Inc. ## Product Family TSW Series Terminal Strip Headers #Samtec #TSW11807GS #TerminalStripHeader #PCBConnector #BoardToBoardConnector #WireToBoardConnector #ElectronicsComponents #EmbeddedSystems #IndustrialElectronics #InterconnectSolutions #ThroughHoleConnector #ElectronicDesign #HardwareEngineering #PCBAssembly #CommonPartsLibrary #Connector #Header #TSW pin header 1x18 2.54mm

The RFFC5072 is a highly integrated wideband RF frequency conversion IC that combines a fractional-N PLL synthesizer, low phase-noise VCO, and a high-linearity RF mixer in a single device. It is designed for wireless infrastructure, software-defined radio (SDR), test equipment, military communications, and broadband frequency conversion applications. The device can generate local oscillator (LO) frequencies from 85 MHz to 4.2 GHz and perform frequency conversion for RF signals up to 6 GHz while maintaining excellent phase noise and spurious performance. Features  85MHz to 4200MHz LO Frequency Range  Fractional-N Synthesizer with Very Low Spurious Levels  Typical Step Size 1.5Hz  Fully Integrated Low Phase Noise VCO and LO Buffers  Integrated Phase Noise • 0.18° rms at 1GHz • 0.50° rms at 3GHz  High Linearity RF Mixer(s)  30MHz to 6000MHz Mixer Frequency Range  Input IP3 +23dBm  Mixer Bias Adjustable for Low Power Operation  Full Duplex Mode (RFFC5071)  2.7V to 3.3V Power Supply  Low Current Consumption  3- or 4-Wire Serial Interface Applications  Wideband Radios  Distributed Antenna Systems  Diversity Receivers  Software Defined Radios  Frequency Band Shifters  Point-to-Point Radios  WiMax/LTE Infrastructure  Satellite Communications  Wideband Jammers #RFFC5072 #Qorvo #RFMixer #FrequencySynthesizer #PLL #VCO #WidebandRF #FrequencyConverter #SDR #WirelessInfrastructure #RFDesign #MicrowaveEngineering #Telecommunications #EmbeddedSystems #ElectronicsDesign #RFIC #SignalProcessing #HardwareEngineering

27 Hz ~ 18 kHz Digital, I2S Microphone MEMS (Silicon) 1.62 V ~ 1.98 V Omnidirectional (-37dB ±1dB @ 94dB SPL) Solder Pads TDK InvenSense T5848 TDK T5848 is a low-noise digital MEMS microphone with a bottom-port acoustic interface and industry-standard I²S digital audio output. The device integrates a MEMS microphone element, impedance converter, ADC, decimation filtering, anti-aliasing filtering, power management, and a 24-bit digital audio interface in a compact 3.5 mm × 2.65 mm × 0.98 mm package. The T5848 supports multiple operating modes including High Quality, Low Power, Sleep, and Always-On Voice (AOV) modes, making it ideal for battery-powered and voice-activated applications. With up to 68 dBA SNR, 133 dB SPL acoustic overload point, and extended frequency response from 27 Hz to 18 kHz, the T5848 is optimized for wearables, IoT devices, smart TVs, gaming systems, teleconferencing equipment, voice assistants, and always-listening audio applications. Search Keywords: T5848, TDK T5848, MEMS Microphone, Digital MEMS Microphone, I2S Microphone, Bottom Port Microphone, Always On Voice Microphone, AOV Microphone, Low Power MEMS Microphone, Wearable Microphone, IoT Audio Sensor, Voice Recognition Microphone, Digital Audio Input, 24-bit I2S Microphone, DSP Microphone, Smart Speaker Microphone, Voice Assistant Microphone, TDK InvenSense Microphone, Teleconference Audio Microphone, Embedded Audio Sensor Hashtags: #T5848 #TDK #InvenSense #MEMSMicrophone #DigitalMicrophone #I2SMicrophone #AudioSensor #AlwaysOnVoice #VoiceRecognition #WearableElectronics #IoTDevices #EmbeddedAudio #VoiceAssistant #SmartDevices #DSP #ElectronicsDesign #PCBDesign #EmbeddedSystems #HardwareEngineering #AudioElectronics

WR-FPC SMT ZIF Horizontal Hinge FFC/FPC Connector, 22 positions, 0.50 mm pitch, bottom-contact type with flip-lock (ZIF) actuator. Surface-mount connector designed for flexible flat cable (FFC) and flexible printed circuit (FPC) connections in compact electronic devices. Horizontal cable entry, low-profile design, halogen-free and RoHS compliant. Suitable for displays, touch panels, cameras, embedded systems, consumer electronics, industrial devices, and PCB interconnect applications. Search Keywords: WR-FPC, WR-FPC SMT ZIF, 687122149022, FFC Connector, FPC Connector, 22 Pin FFC Connector, 22 Pin FPC Connector, 0.5mm Pitch Connector, Bottom Contact Connector, ZIF Connector, Flip Lock Connector, Horizontal FFC Connector, SMT FFC Connector, Würth Elektronik Connector, Flexible Flat Cable Connector, LCD Connector, Display Connector, Camera Connector Hashtags: #WRFPC #687122149022 #WurthElektronik #FFCConnector #FPCConnector #ZIFConnector #FlipLockConnector #SMTConnector #BottomContact #22PinConnector #05mmPitch #FlexibleFlatCable #FlexiblePrintedCircuit #DisplayConnector #EmbeddedHardware #PCBDesign #ElectronicsDesign #HardwareEngineering #IndustrialElectronics #ConsumerElectronicsWR-FPC 0.50mm SMT Horiz. Bot. Contact Hinge type WR-FPC 0.50mm 22pins Hinge type SMT Horizontal Bottom Contact

Buck Switching Regulator IC Positive Adjustable 0.8V 1 Output 3A 8-SOIC (0.154", 3.90mm Width) Exposed Pad MP1584EN-SOP8 MP1584EN-LF-Z is a high-frequency, non-synchronous step-down (buck) DC-DC switching regulator from Monolithic Power Systems. It integrates a high-side power MOSFET and is designed to efficiently convert input voltages from 4.5V to 28V into a lower, regulated output voltage with up to 3A output current. Its high switching frequency enables the use of small external components, making it ideal for compact and cost-effective power supply designs. Key Features: • Wide 4.5V to 28V input voltage range • Adjustable output voltage from 0.8V to 25V • Up to 3A continuous output current • Integrated high-side power MOSFET • Programmable switching frequency from 100kHz to 1.5MHz • Current-mode control for fast transient response • High efficiency with pulse-skipping mode at light loads • Low quiescent current operation • Internal soft-start function • Over-current and thermal shutdown protection • Stable with ceramic output capacitors • Available in SOIC-8E package with exposed thermal pad #MP1584EN #BuckConverter #DCDCConverter #SwitchingRegulator #PowerManagement #VoltageRegulator #MPS #MonolithicPowerSystems #EmbeddedSystems #ElectronicsDesign #PowerSupply #PCBDesign #HardwareEngineering #Electronics #Semiconductor #power #PMIC #IC