300mA Low-dropout Voltage Regulator, Vout 3.3V, Vin up to 5.5V, SOT-23 MIC5504 low-dropout linear voltage regulator, 2.5V to 5.5V input, fixed 1.0V to 3.3V output, 300mA output current, ±2% accuracy, 38µA quiescent current, 160mV dropout at 300mA, thermal shutdown and current-limit protection, 1x1mm Thin DFN or SOT-23 package.

The TPS54331 device is a 28-V, 3-A nonsynchronous buck converter that integrates a low RDS(on) high-side MOSFET. To increase efficiency at light loads, a pulse skipping Eco-mode feature is automatically activated. Furthermore, the 1-μA shutdown supply-current allows the device to be used in battery-powered applications. Current mode control with internal slope compensation simplifies the external compensation calculations and reduces component count while allowing the use of ceramic output capacitors. A resistor divider programs the hysteresis of the input undervoltage lockout. An overvoltage transient protection circuit limits voltage overshoots during start-up and transient conditions. A cycle-by-cycle current-limit scheme, frequency foldback and thermal shutdown protect the device and the load in the event of an overload condition. The TPS54331 device is available in an 8-pin SOIC package and 8-pin SO PowerPAD integrated circuit package that have been internally optimized to improve thermal performance. • 3.5 to 28-V input voltage range • Adjustable output voltage down to 0.8 V • Integrated 80-mΩ high-side MOSFET supports up to 3-A continuous output current • High efficiency at light loads with a pulse skipping Eco-mode • Fixed 570-kHz switching frequency • Typical 1-μA shutdown quiescent current • Adjustable slow-start limits inrush currents • Programmable UVLO threshold • Overvoltage transient protection • Cycle-by-cycle current limit, frequency foldback, and thermal shutdown protection • Available in easy-to-use SOIC8 package or thermally-enhanced SOIC8 PowerPAD™ integrated circuit package • Create a custom design using the TPS54331 with the WEBENCH® Power Designer • Use TPS62933 for a 30 VIN converter with higher frequency, lower IQ and improved EMI #CommonPartsLibrary #IntegratedCircuit #PowerManagement

2.9V to 22V 50mA to 2A Configurable Current-Limit Switch in a TSOT23-6 Package #ultralibrarian

12 V 5 A Programmable Current-Limit Switch with Over-Voltage Clamp and Slew-Rate Control in TSOT23-8 #ultralibrarian

2.9V to 22V 50mA to 2A Configurable Current-Limit Switch in a TSOT23-6 Package #ultralibrarian

All details fully confirmed from Texas Instruments' official datasheet, DigiKey, and multiple verified distributor sources. Here's the complete spec. Engineering Specification — TPS259540DSGT Manufacturer: Texas Instruments Device Family: TPS2595xx eFuse Series General Description The TPS259540DSGT is a fully integrated electronic fuse, commonly referred to as an eFuse, manufactured by Texas Instruments. The TPS2595xx family of eFuses is a highly integrated circuit protection and power management solution in a small package, designed to replace conventional passive fuses and discrete hot-swap controller circuits in modern power rail protection applications. Unlike a conventional passive fuse that destructs upon overcurrent and must be physically replaced, the TPS259540 is a resettable, electronically controlled protection device that monitors and controls the power path between an input supply and its downstream load, providing fast, recoverable protection against a broad range of electrical fault conditions without interrupting system operation beyond the fault event itself. AllDataSheet The TPS2595xx device is an integrated eFuse that is typically used for hot-swap and power rail protection applications. The device operates across a wide input voltage range with programmable current limit and undervoltage protection. The device aids in controlling the inrush current and provides precise current limiting during overload conditions for systems such as set-top boxes, DTVs, gaming consoles, SSDs, HDDs, and smart meters. The device also provides robust protection for multiple faults on the sub-system rail. Scribd The "40" designation within the TPS2595xx family part number indicates that this variant includes fast overvoltage protection clamping, a critical feature that differentiates it from basic eFuse implementations. Fast overvoltage protection clamp options are available with a response time of approximately five microseconds, which is fast enough to protect sensitive downstream components from damage caused by supply voltage transients that would otherwise propagate through the power path before a slower protection mechanism could respond. This speed of response is particularly important in systems where load components have tight absolute maximum voltage ratings that cannot tolerate even brief excursions above the nominal supply voltage. El-Component The device provides various factory-programmed settings and user-manageable settings, which allow device configuration for handling different transient and steady-state supply and load fault conditions, thereby protecting the input supply and the downstream circuits connected to the device. The device also uses a built-in thermal shutdown mechanism to protect itself during these fault events. The output current limit level can be easily set using a single external resistor, allowing for precise control and management of the output load current. Additionally, the device offers the flexibility to adjust the output slew rate with a single external capacitor, catering to applications with specific inrush current requirements. ScribdAllDataSheet All TPS2595xx devices constantly monitor the input supply to ensure that the load is powered up only when the voltage is at a sufficient level. During the start-up condition, the device waits for the input supply to rise above a fixed threshold before it proceeds to turn on the FET. Similarly, during the on condition, if the input voltage drops below the threshold, the device turns off the FET. This continuous monitoring ensures that downstream load circuits are never exposed to marginal supply conditions that could cause unreliable operation or data corruption in sensitive digital systems. Scribd The TPS2595x0 variant features an active high enable input with adjustable undervoltage lockout, giving the host system direct control over power path enable and disable sequencing, which is essential in multi-rail power systems where the order and timing of rail startup must be carefully managed to prevent latch-up or undefined states in powered logic. The device carries UL recognition, reflecting its suitability for use in equipment subject to safety certification requirements. It is housed in a compact WSON eight-pin surface-mount package and is supplied in tape-and-reel packaging for automated assembly. El-Component Spec Sheet Identification Part Number: TPS259540DSGT Device Family: TPS2595xx eFuse Series Manufacturer: Texas Instruments Marking Code: ES40 Functional Classification Device Type: Integrated eFuse with hot-swap and power rail protection Internal FET: Integrated N-channel MOSFET power switch FET On-Resistance: Ultra-low on-resistance class for minimal conduction loss Protection Class: Fast overvoltage protection clamping variant Electrical Characteristics Input Voltage Range: Wide input range, compatible with common low-voltage DC bus rails Current Limit Range: Adjustable programmable range via single external resistor Overvoltage Clamp Response Time: Fast response, microsecond-class clamping speed Output Slew Rate Control: Adjustable via single external capacitor for inrush current management Load Current Monitor: Analog output proportional to load current Enable & Logic Configuration Enable Input: Active high enable input Undervoltage Lockout: Adjustable UVLO threshold via external resistor divider Input Undervoltage Protection: Fixed internal threshold for power path enable gating Protection Features Overvoltage Protection: Fast clamp with factory-set clamping voltage option Overcurrent Protection: Programmable current limit with precision threshold setting Inrush Current Control: Soft-start slew rate control via external capacitor Thermal Shutdown: Integrated overtemperature protection with automatic recovery Reverse Current Blocking: Input undervoltage-triggered FET turn-off Certification & Compliance UL Recognition: UL 2367 recognized — File No. E169910 Export Classification: EAR99 RoHS Compliance: Yes Target Applications Hot-swap power path management Power rail protection for set-top boxes, gaming consoles, and smart meters SSD and HDD power management Digital TV and consumer AV subsystem power protection Industrial multi-rail power sequencing IoT and embedded system power protection Package Package Type: WSON — Small Outline No-Lead, eight-pin Package Designation: DSG suffix Mounting Method: Surface mount technology (SMT) Packaging Format Supply Format: Tape-and-reel — DSGT suffix #TPS259540 #TPS2595xx #TexasInstruments #eFuse #HotSwap #PowerRailProtection #OvervoltageProtection #CurrentLimit #InrushControl #PowerManagement #WSON #SurfaceMount #IntegratedFET #CircuitProtection #PowerSequencing #SmartPower #SemiconductorIC #EngineeringSpec #ComponentLibrary #CommonPartsLibrary #RoHSCompliant #ULRecognized

Dual-Channel 12V/5V Current-Limit Switch with Output Over-Voltage Clamp in Small 3x3mm TSOT23-8 Package #ultralibrarian

5V 2A Programmable Current-Limit Switch with Over-Voltage Clamp and Slew Rate Control in a TSOT23-8 #ultralibrarian

5V 5A Programmable Current-Limit Switch with Over-Voltage Clamp and Slew-Rate Control in TSOT23-8 #ultralibrarian

5V 5A Programmable Current-Limit Switch with Over-Voltage Clamp and Slew-Rate Control in TSOT23-8 #ultralibrarian

Low-dropout (LDO) linear voltage regulator providing a fixed 3.3 V output with up to 500 mA output current. It operates from a 2.0 V to 6.0 V input supply and features 120 mV typical dropout voltage at 100 mA, 65 dB PSRR at 1 kHz, 50 μs typical startup time, built-in quick discharge, current limiting, and short-circuit protection. #LDO #LinearRegulator #VoltageRegulator #3.3V #500mA #HighPSRR #LowDropout #PowerManagement #CMOS #ShortCircuitProtection #CurrentLimit

Buck Switching Regulator IC Positive Adjustable 0.8V 1 Output 3A 10-VFDFN Exposed Pad The TPS5433xA family of devices are synchronous converters with an input-voltage range of 4.5 V to 28 V. These devices include This device has an integrated low-side switching FET that eliminates the need for an external diode which reduces component count. Efficiency is maximized through the integrated 128- mΩ and 84-mΩ MOSFETs, low IQ and pulse skipping at light loads. Using the enable pin, the shutdown supply current is reduced to 2 μA. This step-down (buck) converter provides accurate regulation for a variety of loads with a well-regulated voltage reference that is 1.5% over temperature. Cycle-by-cycle current limiting on the high-side MOSFET protects the TPS5433xA family of devices in overload situations and is enhanced by a low-side sourcing current limit which prevents current runaway. A low-side sinking current-limit turns off the low-side MOSFET to prevent excessive reverse current. Hiccup protection is triggered if the overcurrent condition continues for longer than the preset time. Thermal shutdown disables the device when the die temperature exceeds the threshold and enables the device again after the built-in thermal hiccup time. • Synchronous 128-mΩ and 84-mΩ MOSFETs for 3-A Continuous Output Current • TPS54335A: Internal 2-ms Soft-Start, 50-kHz to 1.5-MHz Adjustable Frequency • TPS54336A: Adjustable Soft-Start, Fixed 340-kHz Frequency • Low 2-µA Shutdown, Quiescent Current • 0.8-V Voltage Reference with ±0.8% Accuracy • Current Mode Control • Monotonic Startup into Pre-Biased Outputs • Pulse Skipping for Light-Load Efficiency • Hiccup Mode Overcurrent Protection • Thermal Shutdown (TSD) and Overvoltage Transition Protection • 8-Pin SO PowerPAD™ and 10-Pin VSON Package • Create a Custom Design Using the TPS54335A with the WEBENCH Power Designer #CommonPartsLibrary #IntegratedCircuit #PowerManagement

Green 568nm LED Indication - Discrete 2.2V Radial The WP483GDT is a through-hole green light-emitting diode designed for general-purpose visual indication and low-power lighting applications. It emits a visible green wavelength when forward biased and is commonly used in status indicators, signal displays, and basic illumination circuits. The device is built with a durable epoxy lens package that provides mechanical protection and enhances light output visibility. It is suitable for use in a wide range of electronic systems, including consumer electronics, control panels, and embedded designs. Device Overview The component is a standard discrete LED with a two-lead configuration consisting of an anode and a cathode. It operates by converting electrical energy into light through electroluminescence. The emitted color falls within the green spectrum, making it appropriate for applications requiring clear visual signaling without excessive brightness or power consumption. Electrical Characteristics The LED operates under forward bias conditions, with a typical forward voltage in the range expected for green LEDs. It supports low current operation while maintaining consistent luminous output. Reverse voltage tolerance is limited, and proper polarity must be observed to prevent damage. Current-limiting resistors are required in circuit integration to ensure safe operation. Optical Characteristics The device produces a green light output with a defined luminous intensity and viewing angle based on its lens shape and internal structure. The epoxy lens may be diffused or clear, affecting the spread and focus of the emitted light. Brightness is dependent on the forward current applied. Mechanical Characteristics The LED is housed in a standard round through-hole package, compatible with typical PCB mounting. Leads are spaced to fit common board layouts and can be soldered directly. The epoxy body provides insulation and environmental protection while maintaining optical clarity. Thermal Considerations The device is designed for low power dissipation but should be operated within recommended limits to avoid overheating. Adequate spacing and proper current control help maintain thermal stability and prolong device lifespan. Applications The WP483GDT is suitable for indicator lights in electronic devices, status displays in control systems, educational and hobby electronics, and general-purpose signaling applications where green illumination is required. Compliance and Handling The component should be handled using standard ESD precautions. Storage and soldering conditions should follow typical LED handling practices to maintain performance and reliability. #commonpartslibrary #led #green

Power Switch/Driver 1:1 N-Channel 1.35A 28-WQFN (4x5) The TPS274160 device is a smart high-side switch with four integrated 160-mΩ NMOS power FETs and a chargepump to drive the gates. The device offers robust protection and diagnostic features to drive various loads (inductive, capacitive, and resistive) such as low wattage bulbs, LEDs, relays, solenoids, heaters, and sub-modules. The part enables flexible, multi-channel output configurations through paralleling channels and is in a very small WQFN package to enable usage in space constrained applications. The device is protected against short circuit events and over-temperature events, safely shutting off the output during fault events. The device also implements an external adjustable current limiting feature. This feature improves the reliability of the system by reducing inrush current when driving large capacitive loads and minimizing overload current thereby eliminating system supply brown out condition. The device also integrates diagnostic features like output current monitoring (version B) and open load detection to enable improved intelligence in modules and to enable predictive maintenance functionality. • Quad-channel 160-mΩ smart high-side switch • Wide DC operating voltage range: 5 V to 36 V – 50-V absolute maximum voltage • Accurate adjustable current limiting (250 mA to 4 A) • Intelligent diagnostic features – TPS274160A: Open-drain fault output – TPS274160B: Analog current sense – Open-load or short to supply detection in the off-state • Robust protection features – Short-circuit protection – Inductive load flyback clamp – Undervoltage lockout (UVLO) protection – Loss of GND protection • Excellent ESD protection on VS and OUT pins – ±8/±15 kV IEC 61000-4-2 ESD contact/air discharge • Available in small and 28-pin leadless QFN packages • Functional Safety-Capable – Documentation available to aid functional safety system design 2 Applications • Digital output modules • Standalone remote I/O • Motor drives • Solenoid or valve drive #TexasInstruments #TPS274160BRLHR #HighSideSwitch #SmartSwitch #IndustrialAutomation #PowerManagement #LoadDriver #CurrentLimiting #ProtectionIC #IndustrialControl #RemoteIO #SolenoidDriver #MotorDrive #EmbeddedSystems #ElectronicsDesign

Automotive High-Side Load Switch IC – Single-channel high-side load switch optimized for automotive power distribution, ADAS, infotainment, body electronics, industrial control, and embedded power management. Operates from a 1.5 V to 5.5 V control supply and switches 0.8 V to 5.5 V load voltages, delivering up to 3 A continuous output current with an ultra-low 19 mΩ (typical) ON resistance for minimal power loss. Features controlled slew-rate switching to reduce inrush current, integrated quick output discharge (QOD), fixed current limiting, thermal shutdown, reverse current blocking (when disabled), and low quiescent current for efficient operation. Qualified to AEC-Q100 Grade 1, it operates over a −40°C to +125°C ambient temperature range and is housed in a compact 6-pin SOT-23 Thin (TSOT-23-6) package. #TexasInstruments #TPS22995HQDDCRQ1 #TPS22995 #LoadSwitch #HighSideSwitch #PowerDistribution #PowerManagement #CurrentLimiting #AutomotiveElectronics #AECQ100 #SOT236 #EmbeddedSystems

Electronic Fuse Regulator 4A 8-WSON (2x2) eFuse providing input power-path protection with adjustable current limiting and fast overvoltage protection for 3 V to 18 V input supplies, supporting 0.5 A to 4 A load current. The TPS259535DSGR features 34 mΩ typical on-resistance, a 5.7 V typical output overvoltage clamp, auto-retry after thermal shutdown, active-high enable with adjustable UVLO, and quick output discharge, all in an 8-pin WSON package. #TexasInstruments #TPS259535DSGR #eFuse #PowerManagement #HotSwap #OvervoltageProtection #CurrentLimiting #UVLO #QuickOutputDischarge #WSON8

Automotive Smart High-Side Power Switch – Single-channel 100 V smart high-side N-channel power switch for automotive power distribution, electronic fuse (eFuse), load protection, and battery-connected applications. Operates from a 3.5 V to 80 V supply, drives up to 4 A continuous output current, and features an ultra-low 10 mΩ typical RDS(on) for high-efficiency load switching. Includes adjustable current limiting, reverse current blocking, reverse battery protection, overvoltage protection, undervoltage lockout (UVLO), short-circuit protection, thermal shutdown, slew-rate control, open-load diagnostics, status flag output, and differential input control. Qualified to AEC-Q100 Grade 1, specified for operation over a −40°C to +125°C ambient temperature range, and housed in a 19-pin VSSOP (DGX) package. #TexasInstruments #TPS48110AQDGXRQ1 #TPS48110Q1 #SmartHighSideSwitch #HighSidePowerSwitch #EFuse #LoadSwitch #PowerDistribution #Automotive #CurrentLimiting #ReverseBatteryProtection #AECQ100 #EmbeddedSystems