Analog to Digital Converters - ADC Single-channel, 9-bit, 1.3-GSPS analog-to-digital converter (ADC) with JESD204C interface 144-FCBGA -40 to 85 ADC09xJ1300 is a family of quad, dual and single channel, 9-bit, 1.3GSPS analog-to-digital converters (ADC). Low power consumption, high sampling rate and 9-bit resolution makes the ADC09xJ1300 ideally suited for suited for a variety of multi-channel communications and test systems. Full-power input bandwidth (-3dB) of 6GHz enables direct RF sampling of L-band and S-band. A number of clocking features are included to relax system hardware requirements, such as an internal phase-locked loop (PLL) with integrated voltagecontrolled oscillator (VCO) to generate the sampling clock. Four clock outputs are provided to clock the logic and SerDes of the FPGA or ASIC. A timestamp input and output is provided for pulsed systems. JESD204C serialized interface decreases system size by reducing the amount of printed circuit board (PCB) routing. Interface modes support from 2 to 8 lanes (dual and quad channel devices) or 1 to 4 lanes (for the single channel device), with SerDes baud-rates up to 17.16Gbps, to allow the optimal configuration for each application. Features • ADC Core: – Resolution: 9 Bit – Maximum sampling rate: 1.3GSPS – Non-interleaved architecture – Internal dither reduces high-order harmonics • Performance specifications (–1dBFS): – SNR (100 MHz): 53.5dBFS – ENOB (100 MHz): 8.5 Bits – SFDR (100 MHz): 64dBc – Noise floor (–20dBFS): –143dBFS • Full-scale input voltage: 80 mVPP-DIFF • Full-power input bandwidth: 6GHz • JESD204C Serial data interface: – Support for 2 to 8 (Quad/Dual channel) or 1 to 4 (Single channel) total SerDes lanes – Maximum baud-rate: 17.16Gbps – 64B/66B and 8B/10B encoding modes – Subclass-1 support for deterministic latency – Compatible with JESD204B receivers • Optional internal sampling clock generation – Internal PLL and VCO (7.2–8.2GHz) • SYSREF Windowing eases synchronization • Four clock outputs simplify system clocking – Reference clocks for FPGA or adjacent ADC – Reference clock for SerDes transceivers • Timestamp input and output for pulsed systems • Power consumption (1GSPS): – Quad Channel: 450mW / channel – Dual channel: 625mW / channel – Single channel: 940mW • Power supplies: 1.1V, 1.9V #CommonPartsLibrary #IntegratedCircuit #ADC #HighSpeedADC #RFADC #JESD204C #13GSPS #9bitADC #DirectRFSampling #TexasInstruments #MixedSignal #DataAcquisition #JESD204

A "Thyone-e & EV-Kit" refers to a set of evaluation boards and development tools provided by Würth Elektronik, centered around their "Thyone-e" radio module, a compact 2.4 GHz wireless transceiver designed for creating mesh networks, sensor networks, and other IoT applications, with the "EV-Kit" part specifically signifying the evaluation board components allowing developers to quickly prototype and test their designs with the Thyone-e module.

UCS 76 04 Is the intelligent bad point continuous transmission series 4 channel65536, level gray scale function LED drive control special circuit, internal integratedMCU, digital interface, data latch, LED high voltage drive and other circuits. Throughthe peripheral MCU control, the separate brightness and cascade control of the chip canrealize the color dot matrix luminescence control of the outdoor large screen. Intelligent bad point continued transmission series IC adopted, advanced HPD intelligent error signal identification technology, the channel error signal identification rate reached more than 99%, and also used the patented dual decodingengine, at the same time monitoring two channels, any channel signal problem real-timeswitch. UCS 7604 RGBW channel output adopts 65535 level gray scale output, with independent current adjustment function of each channel, high precision constant currentdesign, 16K port refresh frequency, so that the picture effect more restore the real color,rich and gorgeous. Excellent product performance, stable and reliable. Double channel bad point transmission function, fault point signal can continue tobe passed down, the overall failure transmission rate of more than 99% Advanced HPD intelligent error signal identification technology, the channel faultidentification rate of more than 99% The patented dual decoding engine simultaneously monitors and decodes two channels,and any problem in the used channel will be switched to normal in real time Channel, and because it is a real-time switch, it is difficult for the human eyeto find the abnormal picture process Can work normally at any frame frequency Advanced channel fault test function, real-time dynamic light on indicates singlechannel fault and channel short circuit recessive fault in the postpartum test oflamps Grayscale level 65536,8 bit (built-in gamma 2.2, corrected to 16 bit) / 12 / 14 / 16 bitdata optional Port refresh frequency is 16K ± 5% high constant current accuracy design RGBW current per channel can be set independently The applied resistance to set the output current, 0-60 mA Data transmission frequencies of 800K / S and 1.6M / S are optional The 1 / 2 / 3 / 4 field mode is optional Chip VDD built-in 5V voltage regulator, output port pressure maximum 30V RGBW channel off, black S-AI anti-interference patented technology, which can greatly reduce and filter outradiation interference and conduction interference S-Drive drive technology and enhanced receiving technology, greatly enhance theconnection distance between points Industrial-grade design, stable and reliable #CommonPartsLibrary #IntegratedCircuit #LED-Driver #4-channel-output

20V, CMOS Decade Counter/Divider, 7 Segment Decoder, Ripple Blanking, Lamp Test, 100mW/Output, DIP-16 schmitt triggered DIP*W7.62mm*

Wide Input 2.7 - 18V 5A High-Efficiency Bidirectional Power Back-Up Manager with Integrated Hot-Swap I2C ADC and Cap Health Test #ultralibrarian

Maxim Integrated PLL Frequency Synthesizer Single 23.5MHz to 6000MHz 32-Pin TQFN EP QFN-32 Maxim None MAX2871ETJ+ Unavailable Maxim Integrated MAX2871 ultra-wideband fractional-N / integer-N PLL frequency synthesizer with integrated VCOs, capable of generating RF frequencies from 23.5MHz to 6.0GHz. Features programmable output dividers (1/2/4/8/16/32/64/128), dual differential RF outputs with programmable output power from -1dBm to +8dBm, low phase noise performance, phase frequency detector up to 140MHz, reference frequency up to 210MHz, fast lock and cycle-slip reduction, automatic/manual VCO selection, on-chip temperature sensor with 7-bit ADC, 4-wire SPI-compatible serial interface, and operation from -40°C to +85°C. Suitable for wireless infrastructure, clock generation, microwave radios, RF signal generation, and test & measurement equipment. MAX2871 Search Keywords: MAX2871, Maxim MAX2871, Analog Devices MAX2871, PLL synthesizer, RF synthesizer, fractional N synthesizer, integer N synthesizer, 6GHz frequency synthesizer, RF signal generator IC, integrated VCO synthesizer, microwave synthesizer, SPI frequency synthesizer, dual output PLL, clock generation IC, wireless infrastructure synthesizer Hashtags: #MAX2871 #MaximIntegrated #AnalogDevices #PLLSynthesizer #FrequencySynthesizer #RFSynthesizer #FractionalNPLL #IntegerNPLL #IntegratedVCO #RFSignalGenerator #MicrowaveRadio #ClockGeneration #WirelessInfrastructure #SPIInterface #TestAndMeasurement #RFDesign #RFIC #PhaseLockedLoop

ADQ-22+ is a surface-mount 2-way RF power splitter/combiner from Mini-Circuits designed for broadband signal distribution and combining applications. It operates over a frequency range of 2 MHz to 500 MHz, providing equal power division with low insertion loss, excellent amplitude balance, and phase balance characteristics. The device features a compact SMT package optimized for automated PCB assembly and RF circuit integration. Typical applications include RF signal distribution, communication systems, instrumentation, microwave links, test equipment, receivers, transmitters, antenna systems, and broadband signal processing circuits where low loss and accurate signal splitting or combining are required. Mini-Circuits ADQ-22+ ADQ-22+, ADQ22+, Mini-Circuits ADQ-22+, RF power splitter, RF power combiner, 2-way power splitter, 2-way power divider, RF signal splitter, broadband power divider, RF distribution network, SMT RF splitter, RF combiner, microwave power divider, communication system RF component, 2MHz to 500MHz splitter, RF signal distribution, test equipment RF splitter, antenna signal splitter, Mini-Circuits power divider Hashtags: #ADQ22 #MiniCircuits #PowerSplitter #PowerDivider #PowerCombiner #RF #RFDesign #MicrowaveEngineering #Telecommunications #SignalDistribution #RFComponents #BroadbandRF #AntennaSystems #TestEquipment #WirelessSystems #Electronics #ElectronicComponents #PCBDesign #RFEngineering #SurfaceMountSignal Conditioning PWR SPLTR CMBD / SURF MT/ RoHS

Test Points/Test Rings 5017 TEST-SMD_L2.7-W1.0 LCSC Part Number: C238130 JLCPCB Part Class: Extended Part Manufactured by Keystone

1.8V to 6.5V, 750mA, 60nA IQ step-down converter The TPS62840 is a high-efficiency step-down converter with ultra-low operating quiescent current of typically 60 nA. The device contains special circuitry to achieve just 120 nA IQ in 100% mode to further extend battery life near the end of discharge. The device uses DCS-Control to cleanly power radios and operates with a typical switching frequency of 1.8 MHz. In Power-Save Mode, the device extends the light load efficiency down to a load current range of 1 μA and below. 16 predefined output voltages can be selected by connecting a resistor to pin VSET, making the device flexible for various applications with a minimum amount of external components. The STOP pin of the device immediately eliminates any switching noise in order to take a noise-free measurement in test and measurement systems. The TPS62840 provides an output current of up to 750 mA. With an input voltage of 1.8 V to 6.5 V, the device supports multiple power sources such as 2S to 4S Alkaline, 1S to 2S Li-MnO2 , or 1S Li-Ion/LiSOCl2 • 60-nA operating quiescent current • 100% duty-cycle mode with 120-nA IQ • Input voltage range VIN from 1.8 V to 6.5 V • Output current up to 750 mA • RF friendly DCS-Control™ • 80% efficiency at 1 µA IOUT (3.6 VIN to 1.8 VOUT) • 16 selectable output voltages via VSET pin • Auto transition PFM/PWM or forced-PWM mode • Selectable forced PWM and STOP modes • Output discharge function • 25-nA shutdown current • SON-8, WCSP-6 and thermally enhanced HVSSOP-8 packages #CommonPartsLibrary #IntegratedCircuit #PowerManagement

IC SURGE STOPPER 2.7V~18V WSON-8-EP(2x2) The TPS2595xx family of eFuses (integrated FET hot swap devices) is a highly integrated circuit protection and power management solution in a small package. The devices provide multiple protection modes using very few external components and are a robust defense against overloads, short circuits, voltage surges, and excessive inrush current. Output current limit level can be set with a single external resistor. It is also possible to get an accurate sense of the output load current by measuring the voltage drop across the current limit resistor. Applications with particular inrush current requirements can set the output slew rate with a single external capacitor. Overvoltage events are quickly limited by internal clamping circuits to a safe fixed maximum, with no external components required. The TPS259573 variant provides an option to set a user-defined overvoltage cutoff threshold. Quick output discharge function can be implemented in the TPS2595x5 variants by connecting the OUT pin to the QOD pin. The devices are characterized for operation over the temperature range of –40°C to +125°C. 1• Wide Input Voltage Range: 2.7 V to 18 V – 20 V Absolute Maximum – 3 V to 18 V for TPS2595x5 Version • Low On-Resistance: RON = 34 mΩ (Typical) • Fast Overvoltage Protection Clamp (3.8-V, 5.7-V, and 13.7-V options) With a Response Time of 5 µs (Typical) • TPS2595x0, TPS2595x1, TPS2595x5: Active High Enable Input With Adjustable Undervoltage Lockout (UVLO) • TPS2595x3: Active Low Enable Input With Adjustable Overvoltage Lockout (OVLO) • Adjustable Current Limit With Load Current Monitor Output (ILM) – Current Range: 0.5 A to 4 A – Current Limit Accuracy: ±7.5% • Adjustable Output Slew Rate Control (dVdt) • Over Temperature Protection (OTP) • Fault Indication Pin (FLT ) • UL 2367 Recognition – File No. E169910 – RILM >= 487 Ω (4.42 A maximum) • IEC 62368-1 Certified • Safe During Single Point Failure Test (IEC 62368- 1) – ILM Pin Open/Short Detection #CommonPartsLibrary #IntegratedCircuit #PowerManagement

High-Accuracy, Low-Power, Digital Temperature Sensor With SMBus- and I2C-Compatible Interface The TMP117 is a high-precision digital temperature sensor. It is designed to meet ASTM E1112 and ISO 80601 requirements for electronic patient thermometers. The TMP117 provides a 16-bit temperature result with a resolution of 0.0078 °C and an accuracy of up to ±0.1 °C across the temperature range of –20 °C to 50 °C with no calibration. The TMP117 has in interface that is I 2C- and SMBus™-compatible, programmable alert functionality, and the device can support up to four devices on a single bus. Integrated EEPROM is included for device programming with an additional 48-bits memory available for general use. The low power consumption of the TMP117 minimizes the impact of self-heating on measurement accuracy. The TMP117 operates from 1.7 V to 5.5 V and typically consumes 3.5 μA. For non-medical applications, the TMP117 can serve as a single chip digital alternative to a Platinum RTD. The TMP117 has an accuracy comparable to a Class AA RTD, while only using a fraction of the power of the power typically needed for a PT100 RTD. The TMP117 simplifies the design effort by removing many of the complexities of RTDs such as precision references, matched traces, complicated algorithms, and calibration. The TMP117 units are 100% tested on a production setup that is NIST traceable and verified with equipment that is calibrated to ISO/IEC 17025 accredited standards. • TMP117 high-accuracy temperature sensor – ±0.1 °C (maximum) from –20 °C to 50 °C – ±0.15 °C (maximum) from –40 °C to 70 °C – ±0.2 °C (maximum) from –40 °C to 100 °C – ±0.25 °C (maximum) from –55 °C to 125 °C – ±0.3 °C (maximum) from –55 °C to 150 °C • Operating temperature range: –55 °C to 150 °C • Low power consumption: – 3.5-μA, 1-Hz conversion cycle – 150-nA shutdown current • Supply range: – 1.7 V to 5.5 V from –55 °C to 70 °C – 1.8 V to 5.5 V from –55 °C to 150 °C • 16-bit resolution: 0.0078°C (1 LSB) • Programmable temperature alert limits • Selectable averaging • Digital offset for system correction • General-purpose EEPROM: 48 bits • NIST traceability • SMBus™, I2C interface compatibility • Medical grade: meets ASTM E1112 and ISO 80601-2-56 • RTDs replacement: PT100, PT500, PT1000 2 Applications • Electronic thermometers • Wireless environmental sensors • Thermostats • Automotive test equipment • Wearable fitness and activity monitors • Cold chain asset tracking • Gas meters and heat meters • Temperature transmitters #CommonPartsLibrary #Sensor

SiTime SiT5356 precision MEMS Super-TCXO oscillator, ±100ppb stability over temperature, programmable frequency from 1MHz to 60MHz in 1Hz steps, ultra-low ±1ppb/°C frequency slope, excellent dynamic stability under airflow, thermal shock, vibration and board bending, integrated regulators for noise filtering, optional TCXO/VCTCXO/DCTCXO configurations, I2C digital frequency pulling option with up to ±3200ppm pull range, LVCMOS or clipped sinewave output, 2.5V/2.8V/3.0V/3.3V supply options, -40°C to +105°C operating range, suitable for 4G/5G radio, GNSS, SyncE, IEEE1588 timing, routers, switches and test equipment. Search Keywords: SiT5356, SiTime SiT5356, MEMS Super-TCXO, precision TCXO, ±100ppb TCXO, programmable TCXO, DCTCXO, VCTCXO, TCXO oscillator, 1MHz to 60MHz oscillator, I2C frequency pulling oscillator, GNSS oscillator, IEEE1588 oscillator, SyncE oscillator, telecom timing oscillator Hashtags: #SiT5356 #SiTimeSiT5356 #SuperTCXO #MEMSOscillator #PrecisionTCXO #ProgrammableOscillator #DCTCXO #VCTCXO #GNSSOscillator #TelecomTiming #IEEE1588 #SyncE #ClockReference #LVCMOSOscillator

Test Points/Test Rings 5019 CONN-SMD_5019 LCSC Part Number: C238131 JLCPCB Part Class: Extended Part Manufactured by Keystone