Programmable Logic Device (CPLDs/FPGAs) XC6SLX75-2CSG484I FPBGA-484_L19.0-W19.0-R22-C22-P0.80-BL LCSC Part Number: C1552413 JLCPCB Part Class: Extended Part Manufactured by AMD/XILINX(赛灵思)

Zero-drift bidirectional current/power monitor with I²C interface The INA219 is a current shunt and power monitor with an I 2C- or SMBUS-compatible interface. The device monitors both shunt voltage drop and bus supply voltage, with programmable conversion times and filtering. A programmable calibration value, combined with an internal multiplier, enables direct readouts of current in amperes. An additional multiplying register calculates power in watts. The I 2C- or SMBUS-compatible interface features 16 programmable addresses Key Features Measures bus voltages from 0 V to 26 V Calculates and reports current, voltage, and power Bidirectional current sensing capability I²C / SMBus-compatible interface Up to 16 programmable I²C addresses High accuracy version (INA219B) with 0.5% maximum error over temperature Programmable conversion time and digital filtering Internal calibration register for direct current measurement in amperes Internal power calculation register for direct power readout in watts Single supply operation from 3 V to 5.5 V Low supply current consumption (typically less than 1 mA) Operating temperature range: −40°C to +125°C Available in SOIC-8 (DR package) and SOT23-8 package options. #CommonPartsLibrary #IntegratedCircuit #PowerManagement

LED Driver IC 16 Output Linear PWM Dimming 25mA 28-TSSOP The PCA9685 is an I2C-bus controlled 16-channel LED controller optimized for Red/Green/Blue/Amber (RGBA) color backlighting applications. Each LED output has its own 12-bit resolution (4096 steps) fixed frequency individual PWM controller that operates at a programmable frequency from a typical of 24 Hz to 1526 Hz with a duty cycle that is adjustable from 0 % to 100 % to allow the LED to be set to a specific brightness value. All outputs are set to the same PWM frequency. Each LED output can be off or on (no PWM control), or set at its individual PWM controller value. The LED output driver is programmed to be either open-drain with a 25 mA current sink capability at 5 V or totem pole with a 25 mA sink, 10 mA source capability at 5 V. The PCA9685 operates with a supply voltage range of 2.3 V to 5.5 V and the inputs and outputs are 5.5 V tolerant. LEDs can be directly connected to the LED output (up to 25 mA, 5.5 V) or controlled with external drivers and a minimum amount of discrete components for larger current or higher voltage LEDs. The PCA9685 is in the new Fast-mode Plus (Fm+) family. Fm+ devices offer higher frequency (up to 1 MHz) and more densely populated bus operation (up to 4000 pF). Although the PCA9635 and PCA9685 have many similar features, the PCA9685 has some unique features that make it more suitable for applications such as LCD or LED backlighting and Ambilight: • The PCA9685 allows staggered LED output on and off times to minimize current surges. The on and off time delay is independently programmable for each of the 16 channels. This feature is not available in PCA9635. • The PCA9685 has 4096 steps (12-bit PWM) of individual LED brightness control. The PCA9635 has only 256 steps (8-bit PWM). • When multiple LED controllers are incorporated in a system, the PWM pulse widths between multiple devices may differ if PCA9635s are used. The PCA9685 has a programmable prescaler to adjust the PWM pulse widths of multiple devices. • The PCA9685 has an external clock input pin that will accept user-supplied clock (50 MHz max.) in place of the internal 25 MHz oscillator. This feature allows synchronization of multiple devices. The PCA9635 does not have external clock input feature. • Like the PCA9635, PCA9685 also has a built-in oscillator for the PWM control. However, the frequency used for PWM control in the PCA9685 is adjustable from about 24 Hz to 1526 Hz as compared to the typical 97.6 kHz frequency of the PCA9635. This allows the use of PCA9685 with external power supply controllers. All bits are set at the same frequency. • The Power-On Reset (POR) default state of LEDn output pins is LOW in the case of PCA9685. It is HIGH for PCA9635. #CommonPartsLibrary #IntegratedCircuit #PowerManagement

Power Supply Controller Digital Power Monitor 10-VSSOP The INA228 is an ultra-precise digital power monitor with a 20-bit delta-sigma ADC specifically designed for current-sensing applications. The device can measure a full-scale differential input of ±163.84 mV or ±40.96 mV across a resistive shunt sense element with common-mode voltage support from –0.3 V to +85 V. The INA228 reports current, bus voltage, temperature, power, energy and charge accumulation while employing a precision ±0.5% integrated oscillator, all while performing the needed calculations in the background. The integrated temperature sensor is ±1°C accurate for die temperature measurement and is useful in monitoring the system ambient temperature. The low offset and gain drift design of the INA228 allows the device to be used in precise systems that do not undergo multi-temperature calibration during manufacturing. Further, the very low offset voltage and noise allow for use in mA to kA sensing applications and provide a wide dynamic range without significant power dissipation losses on the sensing shunt element. The low input bias current of the device permits the use of larger currentsense resistors, thus providing accurate current measurements in the micro-amp range. The device allows for selectable ADC conversion times from 50 µs to 4.12 ms as well as sample averaging from 1x to 1024x, which further helps reduce the noise of the measured data. • High-resolution, 20-bit delta-sigma ADC • Current monitoring accuracy: – Offset voltage: ±1 µV (maximum) – Offset drift: ±0.01 µV/°C (maximum) – Gain error: ±0.05% (maximum) – Gain error drift: ±20 ppm/°C (maximum) – Common mode rejection: 154 dB (minimum) • Power monitoring accuracy: – 0.5% full scale, –40°C to +125°C (maximum) • Energy and charge accuracy: – 1.0% full scale (maximum) • Fast alert response: 75 μs • Wide common-mode range: –0.3 V to +85 V • Bus voltage sense input: 0 V to 85 V • Shunt full-scale differential range: ±163.84 mV / ±40.96 mV • Input bias current: 2.5 nA (maximum) • Temperature sensor: ±1°C (maximum at 25°C) • Programmable resistor temperature compensation • Programmable conversion time and averaging • 2.94-MHz high-speed I2C interface with 16 pinselectable addresses • Operates from a 2.7-V to 5.5-V supply: – Operational current: 640 µA (typical) – Shutdown current: 5 µA (maximum) #CommonPartsLibrary #IntegratedCircuit #PowerManagement

High-Accuracy, Low-Power, Digital Temperature Sensor With SMBus- and I2C-Compatible Interface The TMP117 is a high-precision digital temperature sensor. It is designed to meet ASTM E1112 and ISO 80601 requirements for electronic patient thermometers. The TMP117 provides a 16-bit temperature result with a resolution of 0.0078 °C and an accuracy of up to ±0.1 °C across the temperature range of –20 °C to 50 °C with no calibration. The TMP117 has in interface that is I 2C- and SMBus™-compatible, programmable alert functionality, and the device can support up to four devices on a single bus. Integrated EEPROM is included for device programming with an additional 48-bits memory available for general use. The low power consumption of the TMP117 minimizes the impact of self-heating on measurement accuracy. The TMP117 operates from 1.7 V to 5.5 V and typically consumes 3.5 μA. For non-medical applications, the TMP117 can serve as a single chip digital alternative to a Platinum RTD. The TMP117 has an accuracy comparable to a Class AA RTD, while only using a fraction of the power of the power typically needed for a PT100 RTD. The TMP117 simplifies the design effort by removing many of the complexities of RTDs such as precision references, matched traces, complicated algorithms, and calibration. The TMP117 units are 100% tested on a production setup that is NIST traceable and verified with equipment that is calibrated to ISO/IEC 17025 accredited standards. • TMP117 high-accuracy temperature sensor – ±0.1 °C (maximum) from –20 °C to 50 °C – ±0.15 °C (maximum) from –40 °C to 70 °C – ±0.2 °C (maximum) from –40 °C to 100 °C – ±0.25 °C (maximum) from –55 °C to 125 °C – ±0.3 °C (maximum) from –55 °C to 150 °C • Operating temperature range: –55 °C to 150 °C • Low power consumption: – 3.5-μA, 1-Hz conversion cycle – 150-nA shutdown current • Supply range: – 1.7 V to 5.5 V from –55 °C to 70 °C – 1.8 V to 5.5 V from –55 °C to 150 °C • 16-bit resolution: 0.0078°C (1 LSB) • Programmable temperature alert limits • Selectable averaging • Digital offset for system correction • General-purpose EEPROM: 48 bits • NIST traceability • SMBus™, I2C interface compatibility • Medical grade: meets ASTM E1112 and ISO 80601-2-56 • RTDs replacement: PT100, PT500, PT1000 2 Applications • Electronic thermometers • Wireless environmental sensors • Thermostats • Automotive test equipment • Wearable fitness and activity monitors • Cold chain asset tracking • Gas meters and heat meters • Temperature transmitters #CommonPartsLibrary #Sensor

SPI Flash Serial Flash Memory with Dual/Quad SPI The W25Q16JVUXIQ is a 16-Mbit (2-MByte) Serial NOR Flash memory device from Winbond. It is designed for embedded systems that require non-volatile code and data storage with minimal pin count, low power consumption, and high-speed access. The device supports standard SPI, Dual SPI, and Quad SPI interfaces, making it suitable for firmware storage, boot memory, IoT devices, microcontrollers, consumer electronics, and execute-in-place (XIP) applications. Key Features 16-Mbit (2-MByte) Flash Memory Capacity Operating Voltage: 2.7 V to 3.6 V Standard SPI, Dual SPI, and Quad SPI Interface Support Maximum SPI Clock Frequency: 133 MHz Equivalent Data Transfer Rates: 266 MHz (Dual SPI) 532 MHz (Quad SPI) Continuous Read and XIP (Execute-In-Place) Capability 4 KB Sector Erase, 32 KB Block Erase, 64 KB Block Erase, and Chip Erase 256-Byte Programmable Page Size Minimum 100,000 Program/Erase Cycles per Sector More Than 20 Years Data Retention Ultra-Low Power Consumption Typical power-down current below 1 µA 64-Bit Unique Serial Number Three 256-Byte Security Registers with OTP Protection JEDEC ID and SFDP Support Software and Hardware Write Protection Operating Temperature Options up to +85°C and +105°C Compact 8-Pad USON Package (2 mm × 3 mm) suitable for space-constrained designs #CommonPartsLibrary #IntegratedCircuit #Memory

Electronic Fuse Regulator 5.3A 20-WQFN (3x4) The TPS25940 is a compact, feature-rich eFuse (electronic fuse) power switch from Texas Instruments designed to provide advanced power-path protection and management for SSDs, storage systems, servers, telecom equipment, and other DC-powered applications. It integrates back-to-back MOSFETs for true reverse-current blocking, programmable current limiting, overvoltage/undervoltage protection, and controlled output slew-rate management in a small 20-pin WQFN package. Key Features Wide operating voltage range: 2.7 V to 18 V (20 V maximum input) Low 42 mΩ typical on-resistance (RDS(on)) Adjustable current limit from 0.6 A to 5.3 A True reverse-current blocking using integrated back-to-back FETs Fast reverse-voltage shutdown response of 1 µs Programmable output ramp-up (dV/dt control) for inrush-current management Programmable overvoltage (OVP) and undervoltage (UVP) protection thresholds Integrated IMON analog current-monitor output PGOOD and FLT status outputs for system monitoring Low-power DevSleep™ mode for SATA SSD applications Typical operating quiescent current of 200 µA Typical disabled current of 15 µA Operating junction temperature range from −40°C to +125°C UL 2367 recognized and designed for fault-safe operation under single-point failure conditions. Typical Applications PCIe, SATA, and SAS SSD/HDD storage devices Enterprise servers and storage systems RAID controller cards with holdup-power management Telecom switches and routers Set-top boxes, DTVs, and gaming consoles Adapter-powered equipment General-purpose smart load-switch and power-protection circuits. Package Information Package: 20-pin WQFN (RVC) Temperature range: −40°C to +85°C ambient operation Tape-and-reel packaging for automated assembly. #CommonPartsLibrary #IntegratedCircuit # TPS25940

The HUSB238A is a highly integratedstand-aloneUSB Type-C® and Power Delivery (PD) Sinkcontroller.The HUSB238A integrates the CClogic, USBPDprotocol and the legacy protocols. The HUSB238A can run in I2C mode andGPIOmode.In I2C mode, an I2C master can access theHUSB238Ato configure settings, read back status andperformadvanced functions such as DRSwap, VDMmessages. The HUSB238A supports APDO, maximum48 V/5 A EPR FPDO and EPR AVSin I2Cmode. While in GPIO mode, the configuration is achievedviathe setting pins. The HUSB238A can beconfiguredtosupport maximum 28 V/3.25 A PDOviaVSETandISET pins, only two resistors are usedtoset thevoltage and current. The ultra-low operation current of theHUSB238Ahelps the system to reduce the total power dissipationand suitable for a battery application. The HUSB238A is available in QFN3 mmx3mm-16Lpackage. Fully Autonomous USB Type-C® and USB PD Sink Controller  USB Type-C® Specification Reversion 2.1 and USB PD Specification Reversion 3.1 Supported  Maximum 48 V/5 A PDO Supported – GPIO Mode: Maximum 28 V/3.25 A EPR FPDO and EPR AVS – I2C Mode: Maximum 48 V/5 A EPR FPDO, EPR AVS and SPR PPS Automatic Legacy Protocols Detection Including BC1.2, Divider 3, QC2.0 Support SOP’ Detection Typical Low Power Operation: IVDD< 75 μA Integrated VBUS Switch Driver Dead Battery Support VBUS Over-voltage Protection (OVP) and Under-voltage Protection (UVP) Over-temperature Protection (OTP) with Programmable Thresholds 2 kV HBM ESD Rating for USB IO Pins Small Package, 16 Lead QFN (3 mm x 3 mm) #CommonPartsLibrary #IntegratedCircuit #PowerManagement

The LSM6DSOXTR is a low-power inertial measurement unit integrating a three-axis accelerometer and a three-axis gyroscope within a compact surface-mount package. Designed for motion tracking, gesture recognition, activity monitoring, and sensor fusion applications, the device incorporates embedded machine learning capabilities and programmable finite state machines to enable intelligent edge processing with reduced host processor workload. The sensor supports high-performance motion sensing while maintaining low power consumption, making it suitable for wearable devices, IoT products, industrial monitoring systems, smart home equipment, and portable electronics. Engineering Specification Device Type Six-axis inertial measurement unit featuring a three-axis accelerometer and three-axis gyroscope. Sensor Functions Motion sensing, orientation detection, vibration monitoring, gesture recognition, activity tracking, tilt sensing, and sensor fusion. Integrated Features Embedded machine learning core, finite state machine engine, sensor hub functionality, timestamp generation, event detection, and programmable interrupt generation. Communication Interface Supports digital communication through I²C, SPI, and I³C interfaces for integration with microcontrollers and embedded processors. Power Characteristics Optimized for low-power operation with multiple performance modes supporting battery-powered and always-on applications. Measurement Capabilities Provides configurable acceleration and angular rate measurement ranges with programmable output data rates and digital filtering options. Embedded Intelligence Includes on-chip machine learning and event classification capabilities to enable local data processing and reduce system power consumption. Package Style Compact surface-mount LGA package suitable for space-constrained electronic designs. Applications Wearable electronics, asset tracking devices, industrial sensors, robotics, smart appliances, navigation systems, handheld devices, health monitoring equipment, and IoT products. Manufacturer STMicroelectronics. Hashtags #LSM6DSOXTR #STMicroelectronics #IMU #MotionSensor #Accelerometer #Gyroscope #SensorFusion #MachineLearningCore #EmbeddedSystems #WearableElectronics #IndustrialAutomation #IoT #SmartDevices #MEMS #CommonPartsLibrary

The CC1101RGP is a low-power sub-gigahertz RF transceiver designed for wireless communication applications requiring reliable long-range data transmission and high receiver sensitivity. It integrates a complete radio frequency front-end, packet handling engine, modulation and demodulation circuitry, frequency synthesizer, and advanced power management features within a compact package. The device supports multiple modulation formats and is optimized for industrial, scientific, medical, smart metering, home automation, remote control, wireless sensor networks, and Internet of Things applications. Its flexible configuration options enable designers to achieve an optimal balance between communication range, data throughput, power consumption, and system robustness. Features Sub-gigahertz RF transceiver for license-free ISM frequency bands High receiver sensitivity for extended communication range Programmable output power for optimized power consumption Multiple modulation schemes including FSK, GFSK, ASK, OOK, and MSK Integrated packet handling and error detection functions Fast frequency synthesizer settling time Low current consumption in transmit, receive, and sleep modes Hardware support for address filtering and data buffering Programmable channel spacing and data rate configuration Integrated RSSI, LQI, and clear channel assessment functions SPI interface for configuration and data communication Suitable for battery-powered wireless devices Applications Smart metering systems Wireless sensor networks Industrial monitoring and control Home and building automation Remote keyless entry systems Alarm and security systems Asset tracking devices Telemetry and data acquisition systems IoT communication nodes Proprietary wireless communication networks Electrical Characteristics Wide operating supply voltage range Low-power transmit and receive operation Programmable RF output power levels High-performance frequency synthesizer Low standby and sleep current consumption Integrated crystal oscillator support Robust RF performance across supported frequency bands Interface and Connectivity Serial Peripheral Interface communication Digital control and status signals Configurable interrupt outputs Integrated FIFO buffers for transmit and receive data External antenna connection through matching network Package Information Surface-mount package suitable for automated assembly Compact footprint for space-constrained applications RoHS-compliant device construction #commonpartslibrary #integratedcircuit #wirelesscommunication #rftransceiver #subghz #iot #embeddedsystems #industrialautomation #smartmetering #wirelesssensornetwork #lowpowerdesign #telemetry #homeautomation #remotecontrol #texasinstruments

Microcontroller – 32-bit ARM® Cortex®-M0+ microcontroller operating at up to 64 MHz, featuring 32 KB Flash memory, 8 KB SRAM, and 17 programmable I/O pins. Operates from a 2.0 V to 3.6 V supply and integrates a 13-channel 12-bit ADC, internal and external oscillator support, and communication interfaces including I²C, SPI, UART/USART, IrDA, LIN, and SmartCard. Includes DMA, I²S, PWM, power-on reset (POR), and watchdog timer (WDT) peripherals. Housed in a 20-pin TSSOP package. #STMicroelectronics #STM32 #STM32G030F6P6 #Microcontroller #ARMCortexM0Plus #32BitMCU #64MHz #32KBFlash #8KBSRAM #ADC #I2C #SPI #UART #LIN #SmartCard #TSSOP20 #EmbeddedSystems

USB-A (USB TYPE-A) USB 2.0 Receptacle Connector 4 Position Through Hole, Right Angle The ADS1256IDBT is a high-precision, low-noise, 24-bit analog-to-digital converter manufactured by Texas Instruments. It is designed for high-resolution measurement applications requiring exceptional accuracy, low drift, and programmable data rates. The device integrates a low-noise programmable gain amplifier, a precision delta-sigma ADC core, and a flexible multiplexer that supports multiple differential or single-ended analog inputs. The converter is optimized for industrial process control, sensor measurement, weigh scales, data acquisition systems, temperature monitoring, and portable instrumentation. Its integrated digital filtering and selectable gain settings enable direct interfacing with low-level sensors such as strain gauges, thermocouples, RTDs, and bridge sensors without requiring extensive external signal conditioning. The ADS1256IDBT supports SPI-compatible serial communication and operates with low power consumption while maintaining excellent dynamic performance and high effective resolution. The device provides programmable output data rates suitable for both low-speed precision measurements and higher-speed acquisition systems. Device Features 24-bit delta-sigma analog-to-digital converter Low-noise programmable gain amplifier Eight single-ended or four differential analog input channels Programmable gain settings from 1 to 64 Programmable data output rates SPI-compatible serial interface Integrated digital filter for noise reduction Low offset drift and gain drift Internal oscillator support Sensor burnout detection capability Self-calibration and system calibration functions Low power operation Wide analog supply voltage range Excellent 50 Hz and 60 Hz rejection performance Electrical Characteristics Resolution of 24 bits Maximum data rate up to 30 kSPS Differential input architecture Input multiplexer for multi-channel acquisition Low RMS noise performance High common-mode rejection ratio High power-supply rejection ratio Programmable gain amplifier integrated on-chip Internal reference support with external reference capability Interface and Control SPI-compatible digital communication interface Configurable control registers Read and write register functionality Synchronization and standby control support Hardware reset capability Interrupt and data-ready signaling support Package Information Manufacturer package designation: DBT Package type: TSSOP Surface-mount device Fine-pitch lead configuration Industrial temperature grade device Applications Precision data acquisition systems Industrial automation and control Weigh scales and bridge sensors Temperature measurement systems Pressure sensing applications Portable instrumentation Medical instrumentation Laboratory measurement equipment Energy monitoring systems Process monitoring and control Manufacturer Information Manufacturer: Texas Instruments Manufacturer Part Number: ADS1256IDBT Product Category: Precision Analog-to-Digital Converter RoHS compliant device #commonpartslibrary #integratedcircuit #analog #adc #deltasigma #precisionadc #sensorinterface #dataacquisition #industrialautomation #instrumentation #signalconditioning #texasinstruments #spiinterface #mixedsignal #measurementsystems

868/915MHz SPI SMD LoRa Module E22-900M22S is a compact, industrial-grade LoRa® wireless transceiver module developed by Ebyte, based on the Semtech SX1262 RF chipset. Operating in the 868/915 MHz ISM band, it communicates through an SPI interface and is designed for long-range, low-power wireless data transmission. The module offers excellent receiver sensitivity, strong anti-interference performance, and supports both LoRa and FSK modulation, making it suitable for smart metering, industrial automation, IoT sensor networks, remote monitoring, and wireless control applications. Key Features Based on the Semtech SX1262 LoRa transceiver Operates in the 850–930 MHz frequency range (optimized for 868/915 MHz ISM bands) SPI interface with data rates up to 10 Mbps Maximum transmit power of +22 dBm (160 mW) Receiver sensitivity up to −147 dBm (LoRa mode) Supports LoRa and FSK modulation Programmable air data rate up to 62.5 kbps (LoRa) and 300 kbps (FSK) Long communication range of up to 7 km under ideal line-of-sight conditions Wide operating voltage: 1.8 V to 3.7 V (3.3 V recommended) Ultra-low receive current (~6.8 mA) and low sleep current Industrial operating temperature: −40°C to +85°C Compact 20 × 14 × 2.8 mm SMD package with castellated pads/IPEX antenna options Suitable for IoT, AMI, smart home, industrial sensors, wireless alarms, and remote control systems. #Ebyte #E22Series #E22900M22S #SX1262 #LoRa #WirelessModule #SubGHz #SPI #IoT #IndustrialAutomation #SmartMetering #RemoteMonitoring #EmbeddedSystems #RFModule

Isolated Module DC DC Converter 1 Output 5V 200mA 4.5V - 5.5V Input The TPS259531DSGR is an integrated eFuse and power protection device manufactured by Texas Instruments. This device is designed to provide advanced protection and power management for low-voltage DC power rails in embedded and industrial electronic systems. It integrates multiple protection features including overcurrent protection, overvoltage protection, inrush current control, thermal shutdown, and short-circuit protection within a compact surface-mount package. The device is optimized for hot-swap applications, USB power distribution, industrial control systems, communication equipment, and power sequencing architectures. Its programmable protection thresholds and controlled startup behavior help improve system reliability while protecting sensitive downstream circuitry from abnormal operating conditions. The TPS259531DSGR is commonly used in power distribution networks requiring intelligent fault management and robust circuit protection. Engineering Specification Device Type Integrated eFuse and power protection IC Protection Functions Overcurrent protection Short-circuit protection Overvoltage protection Thermal shutdown Inrush current control Fault monitoring Input Voltage Characteristics Designed for low-voltage DC power rail protection applications Current Management Programmable current limiting and controlled load startup Power Switching Technology Integrated low-resistance MOSFET switching element Fault Handling Automatic fault response and protection isolation Startup Characteristics Adjustable soft-start and inrush current limiting capability Thermal Characteristics Integrated thermal protection with shutdown functionality Package Type WSON surface-mount package Mounting Style Surface mount technology System Integration Features Hot-swap support and power sequencing compatibility Applications USB power distribution Industrial automation Embedded systems Hot-swap systems Communication equipment Power rail protection Server and storage systems Portable electronics Power management architectures Manufacturer Texas Instruments #commonpartslibrary #efuse #powerprotection #powermanagement #texasinstruments #hotswapcontroller #circuitprotection #embeddedhardware #powerelectronics #powersupply #industrialelectronics #surfaceountcomponents #electronicsdesign #powerdistribution #faultprotection

USBPD and Multiple Fast Charging Protocol Receiving Chip CH224 CH224K is a USB Power Delivery protocol controller integrated circuit designed for fast-charging and programmable USB Type-C power negotiation applications. The device enables intelligent voltage trigger and power profile selection from compatible USB Type-C and USB PD power sources, making it suitable for embedded power systems, portable electronics, development boards, and battery-powered devices. This controller supports automatic communication with USB Type-C power adapters to negotiate higher voltage and current profiles for efficient power delivery. It simplifies USB PD implementation by integrating protocol handling, voltage selection logic, and interface control into a compact low-power solution with minimal external component requirements. The CH224K is widely used in DIY electronics, portable charging systems, embedded controllers, IoT hardware, industrial devices, and USB Type-C powered applications requiring stable and configurable DC power input. Its compact surface-mount package and simplified design architecture enable rapid integration into space-constrained PCB layouts. #commonpartslibrary #usbtypec #usbpd #powerdelivery #powermanagement #embeddedhardware #fastcharging #electronicscomponents #portableelectronics #surfacemountdevice

MAX30003CTI+ QFN-28_L5.0-W5.0-P0.50-TL-EP3.3 LCSC Part Number: C1519515 JLCPCB Part Class: Extended Part Manufactured by ADI(亚德诺)/MAXIM(美信) Analog Devices MAX30003 ultra-low-power single-channel integrated biopotential ECG analog front-end (AFE), designed for wearable ECG and heart-rate applications, includes high-resolution ECG data converter, R-to-R detection, ESD protection, EMI filtering, internal lead biasing, DC leads-off detection, right-leg drive, programmable gain, anti-aliasing filter and calibration functions, 15.5-bit effective resolution with 5µVP-P noise, high CMRR over 100dB, high input impedance over 500MΩ, 85µW power consumption at 1.1V supply, leads-on interrupt and heart-rate interrupt functions, available in 28-pin TQFN and 30-bump WLP packages. Search Keywords: MAX30003, Analog Devices MAX30003, Maxim MAX30003, MAX30003 ECG AFE, MAX30003 biopotential AFE, MAX30003 ECG front end, single channel ECG AFE, wearable ECG AFE, R-to-R detection AFE, heart rate ECG sensor IC, low power ECG IC, biopotential analog front end, MAX30003 TQFN-28, MAX30003 WLP-30, MAX30003 datasheet Hashtags: #MAX30003 #AnalogDevicesMAX30003 #MaximMAX30003 #ECGAFE #BiopotentialAFE #ECGFrontEnd #SingleChannelECG #WearableECG #HeartRateAFE #RtoRDetection #LowPowerECG #AnalogFrontEnd #MedicalSensorIC #BiopotentialSensor #HighCMRR #TQFN28 #WLP30

ADS1220IPW is a Texas Instruments 24-bit, 2 kSPS, low-power 4-channel delta-sigma ADC with integrated PGA, 2.048 V reference, oscillator, temperature sensor, SPI interface, and two programmable IDACs, supplied in a 16-pin TSSOP (PW) package for 2.3 V to 5.5 V operation. Tags: 24-bit ADC, delta-sigma, SPI ADC, 4-channel ADC, TSSOP-16

Battery Management ICs BQ24040DSQT WSON-10_L2.0-W2.0-P0.40-TL-EP LCSC Part Number: C2876332 JLCPCB Part Class: Extended Part Manufactured by TI(德州仪器) Texas Instruments BQ2404x highly integrated single-cell Li-Ion/Li-Pol linear battery charger IC for space-limited portable applications, supports USB or AC adapter input, selectable 100mA or 500mA USB input current limit, 1% charge voltage accuracy, 10% charge current accuracy, programmable charge termination and precharge thresholds, 4.35V chemistry support on BQ24045, 30V input rating with 6.6V or 7.1V input overvoltage protection, dynamic power management, thermal regulation and 150°C thermal shutdown, OUT short-circuit and ISET short protection, JEITA battery NTC operation, fixed 10-hour safety timer, status indication, available in 10-pin 2x2mm WSON/DFN package. Search Keywords: BQ2404x, BQ24040, BQ24041, BQ24045, Texas Instruments BQ24040, Texas Instruments BQ24041, Texas Instruments BQ24045, TI BQ2404x, BQ24040 battery charger, BQ24041 battery charger, BQ24045 battery charger, single cell Li-Ion charger, Li-Pol battery charger IC, USB battery charger IC, 500mA battery charger, 100mA USB charger, linear battery charger, 4.35V Li-Ion charger, WSON-10 charger, DFN-10 battery charger, 2x2mm charger IC Hashtags: #BQ2404x #BQ24040 #BQ24041 #BQ24045 #TexasInstrumentsBQ24040 #TIBatteryCharger #BatteryChargerIC #LiIonCharger #LiPolCharger #SingleCellCharger #USBChargerIC #LinearBatteryCharger #500mACharger #100mAUSBCharger #435VCharger #JEITACharger #NTCBatteryCharger #WSON10 #DFN10 #2x2mmPackage

SPI Flash Memory with Dual/Quad SPI The W25Q128JV (128M-bit) Serial Flash memory provides a storage solution for systems with limited space, pins and power. The 25Q series offers flexibility and performance well beyond ordinary Serial Flash devices. They are ideal for code shadowing to RAM, executing code directly from Dual/Quad SPI (XIP) and storing voice, text and data. The device operates on a single 2.7V to 3.6V power supply with current consumption as low as 1µA for power-down. All devices are offered in space-saving packages. The W25Q128JV array is organized into 65,536 programmable pages of 256-bytes each. Up to 256 bytes can be programmed at a time. Pages can be erased in groups of 16 (4KB sector erase), groups of 128 (32KB block erase), groups of 256 (64KB block erase) or the entire chip (chip erase). The W25Q128JV has 4,096 erasable sectors and 256 erasable blocks respectively. The small 4KB sectors allow for greater flexibility in applications that require data and parameter storage. (See Figure 2.) The W25Q128JV supports the standard Serial Peripheral Interface (SPI), Dual/Quad I/O SPI: Serial Clock, Chip Select, Serial Data I/O0 (DI), I/O1 (DO), I/O2 and I/O3. SPI clock frequencies of W25Q128JV of up to 133MHz are supported allowing equivalent clock rates of 266MHz (133MHz x 2) for Dual I/O and 532MHz (133MHz x 4) for Quad I/O when using the Fast Read Dual/Quad I/O. These transfer rates can outperform standard Asynchronous 8 and 16-bit Parallel Flash memories.  New Family of SpiFlash Memories – W25Q128JV: 128M-bit / 16M-byte – Standard SPI: CLK, /CS, DI, DO – Dual SPI: CLK, /CS, IO0, IO1 – Quad SPI: CLK, /CS, IO0, IO1, IO2, IO3 – Software & Hardware Reset(1)  Highest Performance Serial Flash – 133MHz Single, Dual/Quad SPI clocks – 266/532MHz equivalent Dual/Quad SPI – 66MB/S continuous data transfer rate – Min. 100K Program-Erase cycles per sector – More than 20-year data retention  Efficient “Continuous Read” – Continuous Read with 8/16/32/64-Byte Wrap – As few as 8 clocks to address memory – Allows true XIP (execute in place) operation  Low Power, Wide Temperature Range – Single 2.7 to 3.6V supply – <1µA Power-down (typ.) – -40°C to +85°C operating range – -40°C to +105°C operating range Flexible Architecture with 4KB sectors – Uniform Sector/Block Erase (4K/32K/64K-Byte) – Program 1 to 256 byte per programmable page – Erase/Program Suspend & Resume  Advanced Security Features – Software and Hardware Write-Protect – Power Supply Lock-Down – Special OTP protection – Top/Bottom, Complement array protection – Individual Block/Sector array protection – 64-Bit Unique ID for each device – Discoverable Parameters (SFDP) Register – 3X256-Bytes Security Registers with OTP locks – Volatile & Non-volatile Status Register Bits  Space Efficient Packaging – 8-pin SOIC 208-mil – 16-pin SOIC 300-mil (additional /RESET pin) – 8-pad WSON 6x5-mm / 8x6-mm – 24-ball TFBGA 8x6-mm (6x4/5x5 ball array) – 24-ball WLCSP – Contact Winbond for KGD and other options #CommonPartsLibrary #IntegratedCircuit #Memory

Clock Generators, PLLs, Frequency Synthesizers ADF4351BCPZ LFCSP-32_L5.0-W5.0-P0.50-BL-EP3.5 LCSC Part Number: C654681 JLCPCB Part Class: Extended Part Manufactured by ADI(亚德诺)/LINEAR(凌特) Analog Devices ADF4351 wideband fractional-N and integer-N PLL frequency synthesizer with integrated voltage-controlled oscillator (VCO), generating RF output frequencies from 35MHz to 4.4GHz. Features low phase noise, programmable output divider ratios (/1, /2, /4, /8, /16, /32, /64), programmable RF output power, dual-modulus prescaler (4/5 or 8/9), analog and digital lock detect, fast lock mode, cycle slip reduction, auxiliary RF output, RF mute function, and 3-wire serial programming interface. Operates from 3.0V to 3.6V and is widely used in RF signal generators, local oscillators, SDR systems, wireless infrastructure, test equipment, microwave communications, clock generation, and laboratory instrumentation. Search Keywords: ADF4351, Analog Devices ADF4351, ADF4351BRUZ, RF synthesizer, PLL synthesizer, fractional N PLL, integer N PLL, integrated VCO, 35MHz to 4.4GHz synthesizer, RF signal generator IC, microwave frequency synthesizer, local oscillator PLL, SDR synthesizer, programmable RF generator, low phase noise synthesizer, SPI PLL synthesizer, RF clock generator Hashtags: #ADF4351 #AnalogDevices #PLL #FractionalNPLL #IntegerNPLL #FrequencySynthesizer #RFSynthesizer #IntegratedVCO #RFGenerator #SignalGenerator #LocalOscillator #MicrowaveRF #SDR #ClockGenerator #RFIC #WirelessInfrastructure #TestEquipment #LowPhaseNoise #SPIInterface #ADF4351Module

Charger IC Lithium Ion 16-VQFN (3x3) The BQ24075QRGTRQ1 is an automotive-qualified standalone linear battery charger and power-path management integrated circuit designed for single-cell Li-Ion and Li-Polymer battery applications. The device integrates battery charging, system power regulation, input current limiting, and dynamic power-path management into a compact solution optimized for portable and embedded automotive systems. The charger supports USB and external adapter power sources while automatically managing system load distribution between the input supply and battery. Integrated thermal regulation and safety protection features improve reliability under varying operating conditions and harsh automotive environments. The BQ24075QRGTRQ1 supports programmable charging parameters, battery temperature monitoring, and power-good status reporting. The device is qualified for automotive applications and is suitable for infotainment systems, telematics, portable instrumentation, embedded battery-powered modules, and industrial handheld equipment. Key Features Automotive-qualified battery charger IC Single-cell Li-Ion and Li-Polymer battery support Integrated dynamic power-path management USB and adapter input compatibility Programmable fast-charge current control Integrated thermal regulation Input current limiting capability Battery temperature monitoring support Automatic charge termination functionality Short-circuit and over-temperature protection Power-good and charging status indication Compact surface-mount package Optimized for portable and embedded applications Electrical Characteristics Linear charging architecture High integration power management solution Dynamic load sharing between system and battery Stable regulated system output Programmable charging voltage and current Thermal foldback protection operation Low standby and shutdown current consumption Integrated safety timer functionality Wide input operating voltage range Applications Automotive infotainment systems Portable embedded electronics Industrial handheld equipment Battery-powered control modules Telematics systems USB-powered charging systems Portable instrumentation Data logging devices Embedded IoT products Rechargeable battery management systems Package Information Package Type: VQFN Mounting Type: Surface Mount Automotive-grade integrated circuit package RoHS compliant configuration available #commonpartslibrary #integratedcircuit #batterycharger #powermanagement #automotiveelectronics #lithiumbattery #embeddedhardware #usbcharging #portableelectronics #powerpathmanagement

Temperature Sensors DS18B20+T&R TO-92-3_L4.9-W3.7-P2.54-L LCSC Part Number: C880672 JLCPCB Part Class: Extended Part Manufactured by ADI(亚德诺)/MAXIM(美信) DS18B20+T&R programmable resolution 1-Wire digital temperature sensor, local temperature measurement from -55°C to +125°C, 12-bit resolution, ±0.5°C accuracy from -10°C to +85°C, unique 64-bit serial code for multidrop 1-Wire networks, parasite power mode support, user-programmable alarm thresholds, TO-92-3 through-hole package, supplied in tape and reel packaging. Search Keywords: DS18B20+T&R, DS18B20+TR, DS18B20, Analog Devices DS18B20, Maxim DS18B20, 1-Wire temperature sensor, digital temperature sensor TO-92, DS18B20 TO-92-3, 12-bit temperature sensor, -55C to 125C temperature sensor, parasite power temperature sensor Hashtags: #DS18B20 #DS18B20TR #DS18B20TandR #AnalogDevicesDS18B20 #MaximDS18B20 #TemperatureSensor #DigitalTemperatureSensor #1WireSensor #12BitSensor #TO923 #ParasitePowerSensor

2.4GHz Wi-Fi+Bluetooth LE SoC ESP32-S3FH4R2 is a highly integrated low-power Wi-Fi and Bluetooth LE System-on-Chip (SoC) from Espressif Systems. It is based on a dual-core Xtensa® LX7 processor running at up to 240 MHz and is designed for IoT, smart home, industrial control, AIoT, audio processing, and embedded applications. The ESP32-S3FH4R2 variant includes 4 MB of in-package Quad SPI Flash and 2 MB of in-package Quad SPI PSRAM, reducing external component count and simplifying PCB design. Key Features Dual-core Xtensa® LX7 CPU Up to 240 MHz operating frequency 32-bit architecture with floating-point unit (FPU) SIMD instructions for AI and signal-processing workloads Integrated Memory 4 MB in-package Flash 2 MB in-package PSRAM 512 KB on-chip SRAM 384 KB ROM Additional RTC memory for low-power operation Wireless Connectivity IEEE 802.11 b/g/n 2.4 GHz Wi-Fi Bluetooth® 5 Low Energy (LE) Long-range and low-power wireless communication support Rich Peripheral Set Up to 45 programmable GPIOs USB OTG and USB Serial/JTAG SPI, I²C, I²S, UART, SDIO TWAI® (CAN 2.0 compatible) Camera interface LCD interface PWM, pulse counter, RMT, DMA controller Analog Features Two 12-bit SAR ADCs Temperature sensor 14 capacitive touch sensing inputs Security Features Secure Boot Flash Encryption AES, SHA, RSA, HMAC hardware accelerators True Random Number Generator (RNG) Digital Signature peripheral Low-Power Operation Multiple power-saving modes ULP-RISC-V coprocessor ULP-FSM coprocessor Deep-sleep support with RTC memory retention

Direct Digital Synthesis (DDS) AD5933YRSZ SSOP-16_L6.2-W5.3-P0.65-LS7.8-BL LCSC Part Number: C578324 JLCPCB Part Class: Extended Part Manufactured by ADI(亚德诺) Analog Devices AD5933 high-precision impedance converter and network analyzer IC, combines on-board frequency generator with 12-bit 1MSPS ADC and DSP-based DFT processing, programmable excitation voltage up to 100kHz, 27-bit frequency resolution below 0.1Hz, impedance measurement range from 1kΩ to 10MΩ, supports phase and magnitude measurement, internal temperature sensor with ±2°C accuracy, internal system clock option, I2C serial interface, 2.7V to 5.5V supply voltage range, -40°C to +125°C temperature range, 16-lead SSOP package. Search Keywords: AD5933, Analog Devices AD5933, AD5933 impedance converter, AD5933 network analyzer, 12-bit impedance converter, 1MSPS impedance analyzer, impedance measurement IC, complex impedance analyzer, bioelectrical impedance IC, I2C impedance analyzer, AD5933 100kHz, AD5933 SSOP-16, AD5933 datasheet Hashtags: #AD5933 #AnalogDevicesAD5933 #ImpedanceConverter #NetworkAnalyzerIC #ImpedanceAnalyzer #12BitADC #1MSPSADC #BioelectricalImpedance #ComplexImpedanceMeasurement #I2CInterface #100kHzFrequencyGenerator #SSOP16