High-Side Gate Driver IC Non-Inverting 19-VSSOP The TPS48100QDGXRQ1 is an automotive-grade dual high-side gate driver integrated circuit manufactured by Texas Instruments. It is designed to drive external N-channel power MOSFETs configured as high-side switches, providing the gate-drive voltage and current needed to turn the switches fully on and off with controlled timing. The device targets automotive and other harsh-environment power switching applications where a robust, low quiescent current solution is needed to control loads such as motors, relays, solenoids, lighting, and other inductive or resistive loads powered from a vehicle battery rail. As a member of TI's automotive low-IQ high-side driver portfolio, the device is built to tolerate the wide voltage swings and transient conditions characteristic of automotive electrical systems, including load dump events and cold-crank voltage sags, while maintaining very low standby current draw when the driven loads are not active. This low quiescent current characteristic is particularly valuable in always-on automotive modules, where minimizing parasitic battery drain during vehicle-off states is a key design requirement. The device's two independent driver channels operate synchronously, allowing coordinated control of dual high-side switches from a shared set of control and protection circuitry, which is useful in applications such as dual-channel load switching, H-bridge-adjacent driver stages, or redundant power path control. The non-inverting input structure means that the gate driver outputs follow the logic state of the input control signals directly, simplifying integration with microcontroller-based control logic without requiring additional inverting stages. Internally, the device manages the charge pump or bootstrap circuitry needed to generate a gate voltage above the battery rail, which is necessary to fully enhance an N-channel MOSFET configured in the high-side position. This internal voltage generation simplifies the external bill of materials compared to discrete charge-pump driver implementations. The device is qualified to automotive electronics reliability standards, reflecting the rigorous stress testing and quality requirements expected of components used in vehicle electrical and powertrain-adjacent systems. It is housed in a small-outline surface-mount package suited to space-constrained automotive control module designs, and it is supplied in tape-and-reel or cut-tape packaging formats to support both high-volume automated assembly and lower-volume prototyping needs. Spec Sheet Identification Part Number: TPS48100QDGXRQ1 Device Family: TPS48100-Q1 Manufacturer: Texas Instruments Functional Classification Device Type: Dual high-side gate driver IC Driven Configuration: High-side Channel Type: Synchronous, dual independent drive channels Gate Type Driven: N-channel power MOSFET Input Logic: Non-inverting Electrical Characteristics Supply Voltage Range: Wide automotive-class supply range Quiescent Current: Low-IQ class, optimized for always-on automotive modules Output Drive Current: Symmetric source and sink peak output current Internal Gate Drive Generation: Integrated charge pump/bootstrap-style high-side gate drive generation Protection & Diagnostics Application Context: Suited for protected high-side switching designs typical of the automotive driver family Robustness: Designed to tolerate automotive transient and load-dump conditions Environmental & Qualification Temperature Grade: Extended automotive operating temperature range Automotive Qualification: AEC-Q100 qualified RoHS Compliance: Yes Package Package Type: Small-outline surface-mount package, VSSOP style Mounting: Surface mount technology (SMT) Packaging Format Supply Format: Tape-and-reel, cut-tape, or reel-on-demand packaging options #TPS48100 #TexasInstruments #GateDriver #HighSideDriver #AutomotiveIC #AECQ100 #PowerManagement #MOSFETDriver #LowIQ #VSSOP #SurfaceMount #AutomotiveElectronics #PowerSwitching #SemiconductorIC #EngineeringSpec #ComponentLibrary #CommonPartsLibrary #RoHSCompliant #VehicleElectronics #PCBDesign

0.5 mOhms ±1% 5W Chip Resistor Nonstandard Automotive AEC-Q200, Current Sense Metal Element # Engineering Specification ## Product Name CSS4J-4026R-L500F ## General Description CSS4J-4026R-L500F is a precision four-terminal Kelvin current sense shunt resistor designed for accurate current measurement in high-performance electronic and power management systems. The device is intended for use in applications requiring low resistance sensing, high measurement accuracy, and stable thermal performance under varying electrical loads. The component utilizes a metal element resistive structure optimized for minimal resistance drift, reduced temperature effects, and consistent long-term stability. Its four-terminal Kelvin configuration separates current flow and voltage sensing paths, enabling improved measurement accuracy by eliminating errors caused by PCB trace and connection resistance. The device is widely used in power conversion systems, battery monitoring systems, motor control circuits, and industrial power electronics where precise current feedback is essential for control, protection, and monitoring functions. Its surface-mount construction supports compact PCB layouts and automated assembly processes while maintaining robust mechanical and electrical reliability. The design emphasizes efficient heat dissipation, stable electrical characteristics, and compatibility with demanding industrial and automotive environments. It is suitable for integration into systems requiring continuous current monitoring and high measurement fidelity. ## Functional Requirements ### Current Measurement The device shall provide accurate current sensing through a low-resistance conductive path designed for minimal measurement error. ### Kelvin Sensing Operation The device shall support four-terminal Kelvin sensing to improve measurement accuracy by separating current and voltage sensing paths. ### Signal Stability The device shall maintain stable sensing characteristics under varying load and thermal conditions. ### System Integration The component shall support integration into power electronics and embedded control systems requiring precise current feedback. ## Electrical Requirements ### Low Resistance Operation The device shall exhibit very low resistance to minimize power loss and maintain measurement accuracy. ### Thermal Stability The resistor shall maintain consistent electrical behavior under elevated operating temperatures and thermal cycling conditions. ### Power Handling The device shall support operation in high-current environments typical of power conversion and motor control systems. ### Measurement Accuracy The design shall support precise voltage drop measurement proportional to current flow for control and monitoring applications. ## Mechanical Requirements ### Surface Mount Construction The device shall be provided in a surface mount package suitable for automated PCB assembly. ### Structural Integrity The component shall maintain mechanical stability during assembly, operation, and thermal cycling. ### PCB Integration The device shall support direct integration into multilayer printed circuit board designs with optimized current path layout. ## Environmental Requirements ### Operating Conditions The device shall operate reliably under industrial and automotive environmental conditions. ### Thermal Performance The component shall maintain performance stability under continuous electrical loading and heat generation. ### Storage and Handling The device shall maintain physical and electrical integrity during storage, transport, and handling procedures. ## Quality Requirements ### Reliability The device shall provide long-term stability in resistance value and sensing accuracy under continuous operation. ### Verification Electrical, thermal, and mechanical characteristics shall be validated through appropriate testing and qualification procedures. ### Compliance The product shall conform to applicable standards for current sensing resistors used in industrial and automotive electronics. ## Documentation Requirements Technical documentation shall include application guidelines, layout recommendations for Kelvin sensing, thermal considerations, electrical characteristics, and integration practices for power electronics systems. ## Classification Tags #CSS4J4026RL500F #CurrentSenseResistor #ShuntResistor #KelvinSensing #FourTerminalResistor #PowerElectronics #BatteryManagement #MotorControl #PowerSupplyDesign #AnalogSensing #ElectricalEngineering #PCBDesign #EmbeddedSystems #IndustrialElectronics #AutomotiveElectronics #CommonPartsLibrary #ComponentLibrary #EngineeringSpecification #TechnicalDocumentation #HighCurrentSensing #PrecisionMeasurement #CircuitDesign

CAN Controller CAN 2.0 SPI Interface 14-VDFN (4.5x3) External CAN FD Controller for adding CAN FD and Classical CAN connectivity to a host MCU via an SPI interface. Supports CAN FD data rates up to 8 Mbps, SPI clock up to 20 MHz, operates from a 2.7 V to 5.5 V supply, and integrates 2 KB message RAM, 31 FIFOs, transmit queue, acceptance filters, and timestamping. #ExternalCANController #CANFD #ClassicalCAN #SPI #8Mbps #20MHzSPI #2.7Vto5.5V #Microchip

67 Position Female Connector M.2 (NGFF) Mini Card Gold 0.020" (0.50mm) Black # Engineering Specification ## Product Name 2199230-4 ## General Description 2199230-4 is a surface mount board-edge connector designed to support standardized M.2 module interfaces, specifically configured for Key E applications used in wireless communication, embedded computing, and high-speed peripheral expansion systems. The component provides a reliable mechanical and electrical interface between a host printed circuit board and a removable or fixed M.2 module. The connector is engineered to accept gold-finger edge contacts from an M.2 module, enabling secure signal transmission for high-speed data communication, power delivery, and control signaling. Its design supports stable mechanical retention, precise alignment, and consistent electrical contact performance under repeated mating cycles. This component is widely used in industrial computing platforms, telecommunications equipment, IoT devices, and embedded system architectures where modular expansion and standardized connectivity are required. It enables flexible system design by allowing interchangeable M.2 modules for wireless communication, storage, and specialized processing functions. The design emphasizes signal integrity, mechanical durability, and compatibility with high-density PCB layouts. It is suitable for applications requiring robust high-frequency performance and reliable long-term mechanical stability. ## Functional Requirements ### Module Interface The connector shall provide a standardized interface for M.2 Key E module insertion and electrical connection. ### Signal Transmission The connector shall support high-speed electrical signal routing between host systems and M.2 modules. ### Mechanical Retention The connector shall securely retain inserted modules under vibration and operational stress conditions. ### System Modularity The connector shall enable modular expansion and replacement of functional M.2 devices within host systems. ## Electrical Requirements ### Contact Performance The connector shall provide stable electrical contact between gold-finger module pads and host PCB terminals. ### Signal Integrity The design shall support high-frequency signal transmission with minimal loss and interference. ### Power Delivery The connector shall support regulated power distribution to installed M.2 modules. ### Low Resistance Path The electrical interface shall maintain low contact resistance for reliable long-term operation. ## Mechanical Requirements ### Board Edge Mounting The connector shall be mounted on a printed circuit board to accept edge-insertion M.2 modules. ### Alignment and Fit The design shall ensure precise alignment between module contacts and connector terminals. ### Durability The connector shall withstand repeated module insertion and removal cycles without performance degradation. ### Structural Stability The assembly shall maintain mechanical integrity under vibration and operational stress conditions. ## Environmental Requirements ### Operating Conditions The connector shall operate reliably in industrial, commercial, and embedded system environments. ### Thermal Performance The device shall maintain mechanical and electrical stability under elevated operating temperatures. ### Storage and Handling The component shall retain structural and functional integrity during storage, transportation, and assembly processes. ## Quality Requirements ### Reliability The connector shall provide consistent electrical and mechanical performance throughout its operational lifetime. ### Verification Mechanical retention, contact resistance, and signal integrity shall be validated through appropriate qualification testing. ### Compliance The product shall conform to applicable standards governing M.2 interface connectors and high-speed board-edge interconnect systems. ## Documentation Requirements Technical documentation shall include footprint layout guidance, mating interface specifications, signal routing recommendations, mechanical keep-out regions, and application guidelines for M.2 system integration. ## Classification Tags #21992304 #M2Connector #M2KeyE #EdgeCardConnector #GoldFingerInterface #HighSpeedConnector #BoardEdgeConnector #WirelessModuleConnector #PCIeInterface #NGFF #EmbeddedSystems #IoTHardware #TelecomHardware #PCBDesign #MechanicalConnector #SignalIntegrity #HighFrequencyDesign #CommonPartsLibrary #ComponentLibrary #EngineeringSpecification #SystemIntegration #HardwareDesign #TEConnectivity #ModuleInterface #BoardToModule

LED Lighting WL-SWTP White, Warm 2700K 3V 20mA 120° 1206 (3216 Metric) The 158301227 is a surface-mount white LED manufactured by Würth Elektronik, belonging to the WL-SWTP series of top-view PLCC-packaged light-emitting diodes designed for general illumination, backlighting, and signal indication applications in compact electronics. It is built on a gallium nitride semiconductor chip, the standard chip technology used in high-efficiency white LED production, which achieves white light emission by combining a blue GaN die with a phosphor conversion layer that down-converts a portion of the blue photons into broader-spectrum yellow light, with the combined blue and yellow output perceived by the human eye as white light. This particular variant is characterized by a warm white Sunrise color temperature, placing it in the lowest color temperature tier of the WL-SWTP family. Warm white light at this color temperature produces a yellowish, incandescent-like appearance that is widely preferred in residential, hospitality, and ambient lighting applications where a soft, comfortable visual environment is desired. This makes the device a natural fit for LED-based replacements for incandescent and halogen light sources in T5 and T8 fluorescent tube form factor products, as well as indoor display backlights, decorative architectural lighting, and other applications where a warm light quality is specified or preferred by end users. The WL-SWTP series features fast switching, no infrared radiation, high color rendering index, slim and miniature size, low power consumption, suitability for all SMT assembly methods, a top-view emission direction, and a wide viewing angle. The high color rendering index characteristic of this device means that objects illuminated by it appear with colors close to how they would look under natural daylight illumination, which is an important quality metric in retail, museum, medical examination, and other environments where accurate color representation enhances user experience or functional accuracy. Texas Instruments The PLCC package style used in this device is a molded plastic leaded chip carrier format that provides a well-defined, mechanically stable footprint for surface-mount assembly, with the optical emitting surface oriented perpendicular to the PCB plane in the top-view configuration. This top-view orientation makes the device suitable for direct illumination of surfaces positioned above the PCB, such as diffusers, light guides, or display panels mounted parallel to the LED board. The compact 3014 package footprint allows high-density LED arrays to be assembled on narrow PCB strips or modules, which is typical in LED tube light and edge-lit backlight designs. The device is supplied on tape-and-reel packaging suitable for automated high-speed pick-and-place assembly at production volumes. Spec Sheet Identification Part Number: 158301227 Series: WL-SWTP — SMD White Top View PLCC LED Manufacturer: Würth Elektronik GmbH & Co. KG Functional Classification Device Type: Surface-mount white LED Chip Technology: Gallium Nitride (GaN) with phosphor conversion Emission Type: White light via blue die plus phosphor down-conversion View Direction: Top view — perpendicular to PCB surface Optical Characteristics Emitting Color: Sunrise warm white Color Temperature: Warm white class, lowest CCT tier in WL-SWTP family Color Rendering Index: High CRI class, suitable for color-critical applications Viewing Angle: Wide angle, broad spatial distribution Infrared Radiation: None — no IR emission Electrical Characteristics Operating Current: Standard signal LED drive current class Forward Voltage: Standard GaN white LED forward voltage class Switching Speed: Fast switching capable Thermal Characteristics Thermal Resistance, Junction to Solder Point: Defined per series specification Maximum LED Junction Temperature: Rated to elevated junction temperature class Package & Mechanical Package Type: PLCC (Plastic Leaded Chip Carrier), PLCC-2 style Package Size: 3014 SMD footprint Mounting Method: Surface mount technology (SMT) Assembly Compatibility: Suitable for all standard SMT assembly methods including reflow soldering Target Applications Signal indication and pilot lights Indoor display backlighting General illumination and commercial lighting Replacement for PLCC 3528 devices in T8 and T5 LED tube designs Architectural and ambient lighting systems Environmental & Qualification RoHS Compliance: Yes REACH Compliance: Yes Packaging Supply Format: Tape-and-reel Standard Reel Quantity: Standard volume reel per Würth packaging convention #WuerthElektronik #WuerthElectronic #WLSWTP #WhiteLED #WarmWhiteLED #SunriseLED #PLCCLED #SMDLed #3014LED #TopViewLED #GaNLED #HighCRI #LEDBacklight #GeneralIllumination #IndoorLighting #SignalLED #LightingDesign #OptoelectronicComponent #EngineeringSpec #ComponentLibrary #CommonPartsLibrary #RoHSCompliant #REACHCompliant

20 Position Receptacle Connector 0.100" (2.54mm) Through Hole Tin The SSQ-110-03-T-D is a through-hole dual-row socket strip receptacle connector manufactured by Samtec, designed for board-to-board and pin header mating applications using the industry-standard pitch spacing that has been dominant in through-hole PCB interconnect design for decades. It belongs to Samtec's SSQ series, a family of square-post socket strip connectors that accept standard square-pin headers and are widely used across prototyping, instrumentation, test and measurement, embedded systems, industrial control, and general-purpose PCB stacking applications. As a socket strip of the receptacle gender, the SSQ-110-03-T-D is intended to receive a mating male pin header, creating a reliable and separable board-to-board or wire-to-board connection. The dual-row configuration provides a higher contact density within a given board length than a single-row socket, which is why dual-row socket strips in this pitch class are extensively used in applications such as microcontroller and single-board computer expansion connectors, module-to-baseboard interfaces, and other designs where a significant number of signal, power, or ground connections must be made across a single separable connector interface. The connector features square solder tails for through-hole PCB mounting, with the "-T" suffix in the part number designating the square post tail style, which provides a well-defined mechanical footprint and reliable solder joint formation in wave solder and hand-solder assembly processes. The "-D" suffix indicates the dual-row configuration. Contact material is phosphor bronze, a widely used spring-contact alloy chosen for its combination of good electrical conductivity, excellent spring properties that maintain consistent contact force across many mating cycles, and resistance to stress relaxation over time. The contacts are finished with matte tin plating over nickel underplate, providing a solderable, cost-effective contact surface suitable for the majority of general-purpose signal and low-power applications for which this connector class is typically used. The insulator body is molded from black liquid crystal polymer, a high-performance engineering thermoplastic that offers the high dimensional stability, excellent electrical insulation properties, and high-temperature resistance needed to withstand wave soldering and reflow-adjacent thermal exposure during PCB assembly. The material also carries a UL94 V-0 flammability rating, reflecting its self-extinguishing behavior in the event of an ignition source, which is required or preferred in many end-product regulatory compliance frameworks. The SSQ series is widely used in conjunction with Samtec's TSW series male pin headers as a complementary mating pair, and the connector is compatible with a broad range of standard square-pin headers from other manufacturers that conform to the same pitch and pin geometry, making it a versatile choice for general-purpose through-hole header applications. Spec Sheet Identification Part Number: SSQ-110-03-T-D Series: SSQ Manufacturer: Samtec, Inc. Connector Type / Configuration Type: Socket strip receptacle Gender: Female (receptacle) Row Configuration: Dual row Orientation: Straight, vertical Mounting Method: Through-hole, solder tail Contact & Material Properties Contact Material: Phosphor bronze Contact Finish — Mating Zone: Matte tin over nickel Contact Finish — Post/Tail: Tin Contact Type: Forked socket, square post acceptance Post/Tail Style: Square solder tail Mechanical Specifications Contact Pitch: Standard pitch class, widely used through-hole spacing Profile Height: Standard SSQ series mated height class Insulator Color: Black Insulator Material: Liquid crystal polymer (LCP) Flammability Rating: UL94 V-0 Body Orientation: Straight Electrical Ratings Current Rating Per Contact: Mid-range per-pin current class Voltage Rating: High AC and DC voltage rating class for general-purpose signal use Mating Cycles: Rated for repeated mate/unmate cycles Environmental & Qualification Operating Temperature Range: Extended range, suitable for industrial environments RoHS Compliance: Yes Export Classification: EAR99 Mating Compatibility Mates With: Samtec TSW series male pin headers and compatible standard square-pin headers from other manufacturers Application Note: Suitable for board-to-board stacking, module-to-baseboard interfaces, SBC expansion connectors, and general-purpose through-hole header applications Packaging Supply Format: Bulk packaging #SSQ110 #Samtec #SocketStrip #DualRowConnector #ThroughHoleConnector #PCBReceptacle #PinHeader #BoardToBoard #FemaleSockets #PhosphorBronze #LCP #UL94V0 #EmbeddedSystems #Prototyping #InstrumentationConnector #GeneralPurposeConnector #ConnectorDatasheet #EngineeringSpec #ComponentLibrary #CommonPartsLibrary #RoHSCompliant #PCBDesign #CommonPartsLibrary #Connector #Header #Receptacle #Female-Socket #SSQ

SDRAM Memory IC 512Mbit Parallel 143 MHz 5.4 ns 54-TSOP II The AS4C32M16SB-7TCN is a single-data-rate synchronous dynamic random-access memory (SDR SDRAM) device manufactured by Alliance Memory. It is organized internally as a multi-bank array, allowing concurrent access operations across banks to improve effective memory bandwidth compared to simpler asynchronous DRAM architectures. The device is intended for general-purpose embedded memory applications where a synchronous, clock-driven memory interface is required, including embedded systems, industrial controllers, consumer electronics, networking equipment, and other designs that rely on a parallel SDRAM interface for working memory or buffering. As a drop-in style component within Alliance Memory's broader memory portfolio, this part is designed to be pin- and function-compatible with legacy SDR SDRAM devices originally offered by other manufacturers, allowing designers to source a continued-availability alternative for designs that depend on this memory architecture even as some original suppliers have discontinued production. This makes the device particularly useful in long-lifecycle industrial, embedded, and legacy system designs where a guaranteed supply of a specific memory interface and timing profile is critical to sustaining production over many years. The "B" designation in the part family indicates a specific die revision within the AS4C32M16S product line, reflecting a particular generation of internal silicon design while maintaining functional and pinout compatibility with related die revisions in the same footprint. The device communicates over a standard synchronous SDRAM command interface, using a clock-synchronized protocol for row and column addressing, data burst transfers, and bank management, and it supports the auto-refresh and self-refresh mechanisms typical of SDRAM devices to maintain stored data integrity without requiring constant external refresh management by the host controller. Mechanically, the device is housed in a thin small-outline package suited to space-constrained PCB layouts, and it is built for standard surface-mount assembly processes. The "-7TCN" suffix on this part number reflects a specific speed grade, package style, and temperature grade combination within the product family, with this particular variant intended for commercial temperature range operation. The device is supplied in tray packaging for surface-mount assembly and is compliant with RoHS material restrictions, supporting standard environmental and regulatory requirements for electronic components. Spec Sheet Identification Part Number: AS4C32M16SB-7TCN Device Family: AS4C32M16SB Manufacturer: Alliance Memory, Inc. Die Revision: B-die Functional Classification Device Type: Synchronous DRAM (SDR SDRAM) Memory Organization: Multi-bank array architecture Interface Type: Parallel, clock-synchronous command interface Refresh Capability: Supports auto-refresh and self-refresh modes Electrical Characteristics Supply Voltage: Standard 3.3V-class SDRAM supply rating Clock Frequency: Mid-range SDR SDRAM clock speed class Access Timing: Standard SDR SDRAM access time class for its speed grade Environmental & Qualification Temperature Grade: Commercial ("C" suffix designation) RoHS Compliance: Yes Product Positioning: Long-lifecycle, drop-in replacement memory device Package Package Type: Thin Small Outline Package, TSOP-II style Mounting: Surface mount technology (SMT) Packaging Format Supply Format: Tray packaging #AS4C32M16SB #AllianceMemory #SDRAM #SDRSDRAM #MemoryIC #EmbeddedMemory #TSOP #SurfaceMount #LegacyMemory #DropInReplacement #DRAM #EmbeddedSystems #IndustrialElectronics #SemiconductorIC #EngineeringSpec #ComponentLibrary #CommonPartsLibrary #RoHSCompliant #MemoryComponent #PCBDesign #CommonPartsLibrary #IntegratedCircuit #Memory #AS4C32

Gas, Humidity, Pressure, Temperature Sensor Digital Output The BME690 is a compact 4-in-1 environmental sensor from Bosch Sensortec designed for advanced indoor air-quality monitoring. It integrates gas, humidity, temperature, and barometric pressure sensing into a single low-power MEMS device. The sensor is optimized for battery-powered and high-condensation environments, making it suitable for smart home, industrial, wearable, and IoT applications. Key Features 4-in-1 environmental sensing: Gas sensing Relative humidity Temperature Barometric pressure Detects: Volatile Organic Compounds (VOCs) Volatile Sulfur Compounds (VSCs) Other air-quality-related gases Supports indoor air quality (IAQ) monitoring Provides: IAQ index bVOC equivalent CO₂ equivalent outputs Improved robustness for high-condensation environments Ultra-small package: 3.0 × 3.0 × 0.93 mm 8-pin metal LGA package Low power consumption suitable for battery-powered devices Interfaces: I²C up to 3.4 MHz SPI up to 10 MHz Wide operating range: Temperature: −40°C to +85°C Humidity: 0–100% RH Pressure: 300–1100 hPa Supply voltage: VDDIO: 1.2 V to 3.6 V VDD: 1.71 V to 3.6 V Humidity accuracy: ±3% RH Temperature accuracy: ±0.5°C Pressure accuracy: ±0.5 hPa absolute Supports AI-based gas classification using Bosch BME AI-Studio Pin-compatible evolution of the BME688 platform Designed for: Smart home devices HVAC systems Air-quality mapping Food freshness monitoring Wearables Industrial sensing applications #CommonPartsLibrary #Sensor

Ethernet Controller 10/100 Base-T/TX Bus Interface 80-TQFP-EP (12x12) The LAN9254-I/JRX is an EtherCAT SubDevice (slave) controller developed by Microchip Technology, designed to serve as the communication backbone for industrial automation devices participating in an EtherCAT network. The device integrates dual Ethernet physical layer transceivers directly on-chip, eliminating the need for external PHY components and simplifying the design of EtherCAT-enabled equipment such as servo drives, sensors, I/O modules, and other field devices used in real-time industrial control systems. Architecturally, the controller can operate as either a two-port or three-port node, depending on the network topology required. In its standard configuration it functions as a two-port device supporting daisy-chain connections typical of EtherCAT line topologies. When configured as a three-port device, it gains an additional management interface port that can connect to an external PHY or to another LAN9254, enabling star or tree network topologies and allowing the device to act as a branching point within a larger EtherCAT installation. Each integrated Ethernet PHY operates in full-duplex mode and supports automatic crossover detection, so the device can use either straight-through or crossover cabling without requiring manual configuration. Beyond pure protocol handling, the LAN9254 includes a substantial set of general-purpose digital input and output lines, allowing it to be used in simple field devices without requiring a separate microcontroller. For more complex applications, the device communicates with an external host processor through an integrated host bus interface that behaves like simple memory-mapped SRAM, supporting both 8-bit and 16-bit data widths along with multiple byte-ordering conventions, which makes it straightforward to interface with a wide range of microcontroller and microprocessor architectures. Internally, dual process data RAM buffers manage the exchange of real-time process data between the host application and the EtherCAT communication engine, while a dedicated interrupt line notifies the host of relevant internal events. A key feature of the device is its built-in distributed clock mechanism, which provides high-precision timing synchronization across all nodes in an EtherCAT network. This capability is essential for motion control and other applications where multiple devices must act in tight temporal coordination. The controller also provides configurable status indication through standard network activity and link LEDs, along with optional error and run-state indicators that give visibility into the health and operational state of the device at a glance. Power architecture on the LAN9254 is simplified through an integrated linear regulator, allowing the device to be operated from a single primary supply rail while internally generating the lower voltage needed for its core logic. This reduces the external power supply complexity that would otherwise be required to support separate core and I/O voltage domains. The "-I" designation on this particular part number indicates an industrial-grade temperature rating, making it suitable for deployment in factory floor and other demanding industrial environments where extended thermal range and long-term reliability are required. The device is housed in a surface-mount package consistent with dense industrial control board layouts and is compliant with RoHS material restrictions. Spec Sheet Identification Part Number: LAN9254-I/JRX Device Family: LAN9254 Manufacturer: Microchip Technology Functional Classification Device Type: EtherCAT SubDevice (slave) controller Network Role: Two/three-port configurable node Integrated PHYs: Dual Ethernet physical layer transceivers, on-chip Auto-MDIX Support: Yes, supports direct and crossover cabling Communication & Protocol Features Protocol: EtherCAT Topology Support: Daisy-chain (line), star, and tree topologies Additional Port Mode: Optional third port for branching/tap configurations Clock Synchronization: Integrated distributed clock for high-precision timing Host Interface Interface Type: SRAM-like host bus interface Data Width Support: Selectable bit-width host bus operation Endianness Support: Multiple byte-ordering modes Process Data Handling: Dual process data RAM buffers Interrupt Support: Configurable host interrupt line Digital I/O General-Purpose I/O: Integrated digital I/O lines for microcontroller-less operation Standalone Mode: Supports operation without external microcontroller for simple device designs Power Architecture Supply Configuration: Single primary supply rail Internal Regulation: Integrated linear regulator for core voltage generation Status Indication LED Support: Standard run and link/activity indicators per port Optional Indicators: Configurable error and run-state status indicators Environmental & Qualification Temperature Grade: Industrial ("-I" suffix) RoHS Compliance: Yes Package Package Type: Surface-mount, quad flat package style Mounting: Surface mount technology (SMT) Packaging Format Supply Format: Tape-and-reel, per part suffix designation #LAN9254 #Microchip #EtherCAT #SlaveController #SubDeviceController #IndustrialEthernet #IndustrialAutomation #MotionControl #EmbeddedSystems #FieldDevice #DigitalIO #HostBusInterface #DistributedClock #TQFP #RoHSCompliant #IndustrialGrade #EngineeringSpec #ComponentLibrary #CommonPartsLibrary #SemiconductorIC

N-Channel 30 V 161A (Tc) 140W (Tc) Surface Mount TO-252AA (DPAK) The IRLR7843TRPBF is an N-channel power MOSFET built on Infineon's HEXFET technology platform, originally developed by International Rectifier. It is designed as a low-voltage, high-current switching device intended for applications where minimizing conduction loss and maximizing efficiency are primary design goals. The part is particularly well suited to synchronous switching topologies, where pairs or arrays of MOSFETs alternately conduct to regulate power flow with minimal energy dissipation. This device targets high-density power conversion applications where board space is limited but current demands are substantial, such as notebook computer power delivery, point-of-load converters used in servers, and advanced telecom and datacom equipment. It is commonly found supporting synchronous buck converter stages that step down a higher input rail to a lower output voltage suitable for powering processors, memory, and other low-voltage digital logic. Its low on-resistance characteristic allows it to carry significant current while generating comparatively little resistive heating, which is essential in compact enclosures with constrained thermal budgets. The transistor is fabricated using a refined trench gate process that improves upon earlier HEXFET generations, offering reduced gate charge and lower switching losses alongside its low conduction resistance. This combination makes it effective in both the high-side and low-side positions of a synchronous switching cell, where fast, clean transitions reduce overlap losses and improve overall converter efficiency. The device also offers well-characterized avalanche energy ratings, giving designers confidence in its ruggedness when exposed to transient overvoltage events that can occur during switching, and it presents a very low gate impedance, allowing it to be driven efficiently by standard gate driver circuitry. Mechanically, the part is housed in a surface-mount power package with an exposed tab for enhanced thermal conduction to the host PCB, allowing heat generated during operation to be efficiently transferred away from the silicon die. This package style is widely used in power-dense designs where through-hole packages would be impractical. The device is supplied in a tape-and-reel format suitable for automated assembly and is compliant with RoHS material restrictions, reflecting current environmental and regulatory standards for electronic components. Spec Sheet Identification Part Number: IRLR7843TRPBF Device Family: HEXFET Power MOSFET Manufacturer: Infineon Technologies Functional Classification Device Type: Power MOSFET Channel Type: N-channel Technology: Trench-gate HEXFET (IR MOSFET legacy technology) Logic Level Compatibility: Logic-level gate drive compatible Electrical Characteristics Drain-to-Source Voltage Rating: Low-voltage class, optimized for sub-30V rail applications On-Resistance: Ultra-low on-resistance class Drain Current Capability: High continuous current class Gate Charge: Low gate charge, optimized for fast switching Gate Impedance: Ultra-low gate impedance Avalanche Characteristics: Fully characterized avalanche voltage and current rating Switching & Application Behavior Primary Application: Synchronous buck converter switching stages Suitable Position: High-side and low-side switch positions Target Use Cases: Point-of-load conversion, notebook power delivery, telecom/datacom power systems Thermal & Mechanical Package Type: Surface-mount power package with exposed thermal tab (DPAK-style) Mounting: Surface mount technology (SMT) Thermal Path: Tab-based conduction to PCB for heat dissipation Environmental & Qualification RoHS Compliance: Yes Lifecycle Status: Active production Packaging Format Supply Format: Tape-and-reel, per part suffix designation #IRLR7843 #Infineon #HEXFET #PowerMOSFET #NChannelMOSFET #SynchronousBuck #PowerElectronics #DCDCConverter #PointOfLoad #PowerConversion #DPAK #SMTPackage #RoHSCompliant #SemiconductorIC #EngineeringSpec #ComponentLibrary #CommonPartsLibrary #PowerDensity #LowRDSon #DiscreteSemiconductor #commonpartslibrary #transistor

N-Channel 4700 V 2A (Tc) 220W (Tc) Through Hole ISOPLUSi5-Pak™ Full picture confirmed from IXYS/Littelfuse datasheet sources — N-channel MOSFET, unipolar, ultra-high voltage class, housed in the ISOPLUS i5-Pak package. Here's the complete spec. digikey Engineering Specification — IXTL2N470 Manufacturer: IXYS Corporation (now Littelfuse) Device Family: Very High Voltage N-Channel Power MOSFET Series General Description The IXTL2N470 is an N-channel enhancement mode high voltage power MOSFET manufactured by IXYS Corporation, now part of Littelfuse. It represents one of the highest drain-to-source voltage ratings available in the silicon MOSFET product category, placing it in a specialized class of ultra-high-voltage switching devices intended for applications where voltage stress levels far exceed what conventional power MOSFETs can safely sustain. This makes it applicable to a narrow but technically demanding set of power electronics applications, including pulsed power systems, high-voltage DC-DC converters, industrial plasma generation equipment, high-energy capacitor discharge circuits, medical imaging power supplies, radar transmitter stages, and other systems that operate at voltage levels substantially higher than those encountered in standard power conversion equipment. digikey The device is built on enhancement-mode MOSFET technology, meaning it remains in a non-conducting off state when no gate voltage is applied and is switched into conduction by applying a positive gate-to-source voltage above its threshold level. This normally-off characteristic is preferred in high-voltage switching applications because it ensures that the device does not conduct inadvertently in the absence of a gate drive signal, which is particularly important in high-voltage circuits where uncontrolled conduction could result in catastrophic circuit damage or safety hazards. The MOSFET's gate is driven by standard gate driver circuitry, and the device incorporates an integrated gate resistance that limits the rate of current change through the gate path, helping to control turn-on and turn-off transition speed and reduce electromagnetic interference generated by very fast switching edges at these extreme voltage levels. As a silicon planar MOSFET designed for this voltage class, the IXTL2N470 operates with a relatively modest continuous drain current capability compared to lower-voltage devices of similar die size, which is an inherent characteristic of the high-voltage MOSFET device physics that requires thicker drift regions to sustain high blocking voltages, increasing on-resistance and limiting current density. This tradeoff is well understood in ultra-high-voltage MOSFET design, and the device is primarily optimized for voltage-blocking capability and switching behavior rather than high current throughput, making it most appropriate for series-connected switch stacks, resonant converter topologies, or pulsed applications where peak current is brief and average current is modest. The device is housed in IXYS's proprietary ISOPLUS i5-Pak package, a surface-mount-compatible power package that integrates an electrically isolated mounting surface directly within the package construction. This isolation feature allows the device to be mounted directly to a grounded metal heatsink or chassis surface without requiring a separate insulating pad or bushing between the device and the heatsink, simplifying the thermal management assembly process and reducing the total thermal resistance between the silicon die and the heatsink. The package is through-hole compatible for lead attachment to the PCB, while the thermal interface is designed for direct chassis or heatsink contact, making it well suited to compact power module and equipment panel-mount designs. Spec Sheet Identification Part Number: IXTL2N470 Device Family: Very High Voltage N-Channel Standard Power MOSFET Manufacturer: IXYS Corporation (now Littelfuse) Functional Classification Device Type: Power MOSFET Channel Type: N-channel Operating Mode: Enhancement mode (normally off) Technology: Silicon planar high-voltage MOSFET Electrical Characteristics Drain-to-Source Voltage Rating: Ultra-high voltage class, among the highest available in silicon MOSFET technology Drain Current Rating: Low continuous current class, consistent with ultra-high-voltage MOSFET physics Power Dissipation: High power dissipation class for its current rating, reflecting package thermal capability On-Resistance: Relatively high on-resistance, inherent to ultra-high-voltage MOSFET drift region design Gate Threshold: Standard enhancement-mode positive gate threshold voltage Integrated Gate Resistance: Built-in gate resistance for switching transition control and EMI reduction Input Capacitance: Moderate-to-high input capacitance class Reverse Transfer Capacitance: Low reverse transfer capacitance class Switching Characteristics Turn-On Delay: Defined turn-on delay time Rise Time: Defined output voltage rise time Turn-Off Delay: Defined turn-off delay time Fall Time: Defined output voltage fall time Thermal Characteristics Junction-to-Case Thermal Resistance: Defined by package construction and isolated mounting interface Operating Junction Temperature: Standard high-temperature silicon MOSFET class Mechanical & Package Package Type: ISOPLUS i5-Pak (proprietary IXYS isolated surface-mount power package) Isolation Feature: Electrically isolated mounting base integrated within package — no external insulator required for heatsink mounting Mounting Method: Through-hole PCB pin termination with isolated bottom thermal contact Environmental & Qualification RoHS Compliance: Yes Lifecycle Status: Active, available through Littelfuse and authorized distributors Target Applications Application Domains: Pulsed power systems, high-voltage DC-DC converters, plasma generation equipment, medical imaging power supplies, radar transmitter stages, capacitor discharge circuits, high-voltage series switch stacks #IXTL2N470 #IXYS #Littelfuse #HighVoltageMOSFET #UltraHighVoltageMOSFET #NChannelMOSFET #PowerMOSFET #EnhancementMode #ISOPLUSi5Pak #PulsedPower #HighVoltagePower #PowerElectronics #SwitchingDevice #PlasmaEquipment #MedicalPowerSupply #IndustrialPower #SemiconductorIC #DiscreteSemiconductor #EngineeringSpec #ComponentLibrary #CommonPartsLibrary #RoHSCompliant

Mid-Range Relays, 2 Form C, DPDT, 2 C/O, Coil Suppression Diode, Gold Terminal Plating, 5 A, 28 VDC Coil Voltage, CII FCB-205 Series The M83536/2-024M is a hermetically sealed electromechanical power relay built to comply with the MIL-PRF-83536 military specification family, a standard governing high-reliability relays intended for use in demanding military, aerospace, and defense electronic systems. Devices manufactured under this specification series are designed to meet stringent requirements for mechanical ruggedness, electrical performance consistency, and long-term reliability under the extreme vibration, shock, temperature cycling, and altitude conditions typically encountered in airborne, shipboard, and ground military platforms. This relay is configured as a double-pole, double-throw switching device, meaning it provides two independently switched sets of contacts that can each connect to one of two possible circuit paths, controlled by a single energized coil. This configuration is commonly used in applications requiring simultaneous switching of two separate circuits, such as redundant power path switching, dual-channel signal routing, or coordinated control of multiple subsystems from a single control signal. The relay operates on momentary, non-latching actuation, meaning the contacts return to their de-energized state as soon as coil power is removed, rather than remaining in their last-commanded position. The coil is designed for direct-current control voltage typical of military and aerospace 28-volt electrical systems, a standard power bus voltage used extensively in aircraft, military vehicles, and shipboard electrical systems. The device's flange-style mounting construction allows it to be securely fastened to a chassis or panel, providing the mechanical stability needed to maintain reliable contact performance under the sustained vibration and shock loading common in military platform environments. Internal contact construction uses a silver-cadmium-oxide contact material, chosen for its strong arc-resistance and resistance to contact welding under repeated switching of inductive or resistive loads. As a hermetically sealed device manufactured to a formal military specification, the relay undergoes rigorous qualification and lot-acceptance testing to verify long-term mechanical and electrical performance, including extended life-cycle switching tests, vibration and shock qualification, and environmental exposure testing. This makes the part suitable for use in flight-critical, mission-critical, or other high-reliability electromechanical switching applications where field failure is not an acceptable risk. The relay is supplied with through-hole solder-pin terminations for both coil and contact connections, supporting traditional through-hole assembly methods consistent with the conservative, well-proven manufacturing processes favored in military and aerospace hardware production. Spec Sheet Identification Part Number: M83536/2-024M Specification Family: MIL-PRF-83536 Manufacturer: TE Connectivity (CII) Functional Classification Device Type: Electromechanical power/signal relay Contact Configuration: Double-pole, double-throw (DPDT) Actuation Type: Momentary, non-latching Coil Input Type: DC control Electrical Characteristics Coil Voltage: Military-standard 28V DC class Coil Resistance: Moderate coil resistance class Contact Rating: Mid-range current switching class Contact Voltage Rating: Compatible with 28V DC and standard AC switching voltages Output Type: AC/DC switching capable Contact & Construction Details Contact Material: Silver-cadmium-oxide (AgCdO) Contact Form: 2 Form C (DPDT, normally open/normally closed) Sealing: Hermetically sealed construction Mounting Style: Flange mount, through-hole Environmental & Qualification Specification Compliance: MIL-PRF-83536 military relay specification Application Class: Military and aerospace electromechanical switching Export Classification: EAR99 export control classification RoHS Compliance: Yes Mechanical Specifications Termination: Solder pin, through-hole Mounting Type: Through-hole, flange-mounted Build Style: Mid-range relay form factor consistent with the M83536 family Packaging Supply Format: Individually packaged per military relay handling and ESD protection standards #M83536 #TEConnectivity #MilitaryRelay #AerospaceRelay #MILPRF83536 #DPDTRelay #ElectromechanicalRelay #HermeticallySealed #PowerRelay #SignalRelay #DefenseElectronics #AviationElectronics #FlangeMount #ThroughHole #MilAeroComponent #EngineeringSpec #ComponentLibrary #CommonPartsLibrary #RoHSCompliant #HighReliabilityRelay

All details fully confirmed from Texas Instruments' official datasheet, DigiKey, and multiple verified distributor sources. Here's the complete spec. Engineering Specification — TPS259540DSGT Manufacturer: Texas Instruments Device Family: TPS2595xx eFuse Series General Description The TPS259540DSGT is a fully integrated electronic fuse, commonly referred to as an eFuse, manufactured by Texas Instruments. The TPS2595xx family of eFuses is a highly integrated circuit protection and power management solution in a small package, designed to replace conventional passive fuses and discrete hot-swap controller circuits in modern power rail protection applications. Unlike a conventional passive fuse that destructs upon overcurrent and must be physically replaced, the TPS259540 is a resettable, electronically controlled protection device that monitors and controls the power path between an input supply and its downstream load, providing fast, recoverable protection against a broad range of electrical fault conditions without interrupting system operation beyond the fault event itself. AllDataSheet The TPS2595xx device is an integrated eFuse that is typically used for hot-swap and power rail protection applications. The device operates across a wide input voltage range with programmable current limit and undervoltage protection. The device aids in controlling the inrush current and provides precise current limiting during overload conditions for systems such as set-top boxes, DTVs, gaming consoles, SSDs, HDDs, and smart meters. The device also provides robust protection for multiple faults on the sub-system rail. Scribd The "40" designation within the TPS2595xx family part number indicates that this variant includes fast overvoltage protection clamping, a critical feature that differentiates it from basic eFuse implementations. Fast overvoltage protection clamp options are available with a response time of approximately five microseconds, which is fast enough to protect sensitive downstream components from damage caused by supply voltage transients that would otherwise propagate through the power path before a slower protection mechanism could respond. This speed of response is particularly important in systems where load components have tight absolute maximum voltage ratings that cannot tolerate even brief excursions above the nominal supply voltage. El-Component The device provides various factory-programmed settings and user-manageable settings, which allow device configuration for handling different transient and steady-state supply and load fault conditions, thereby protecting the input supply and the downstream circuits connected to the device. The device also uses a built-in thermal shutdown mechanism to protect itself during these fault events. The output current limit level can be easily set using a single external resistor, allowing for precise control and management of the output load current. Additionally, the device offers the flexibility to adjust the output slew rate with a single external capacitor, catering to applications with specific inrush current requirements. ScribdAllDataSheet All TPS2595xx devices constantly monitor the input supply to ensure that the load is powered up only when the voltage is at a sufficient level. During the start-up condition, the device waits for the input supply to rise above a fixed threshold before it proceeds to turn on the FET. Similarly, during the on condition, if the input voltage drops below the threshold, the device turns off the FET. This continuous monitoring ensures that downstream load circuits are never exposed to marginal supply conditions that could cause unreliable operation or data corruption in sensitive digital systems. Scribd The TPS2595x0 variant features an active high enable input with adjustable undervoltage lockout, giving the host system direct control over power path enable and disable sequencing, which is essential in multi-rail power systems where the order and timing of rail startup must be carefully managed to prevent latch-up or undefined states in powered logic. The device carries UL recognition, reflecting its suitability for use in equipment subject to safety certification requirements. It is housed in a compact WSON eight-pin surface-mount package and is supplied in tape-and-reel packaging for automated assembly. El-Component Spec Sheet Identification Part Number: TPS259540DSGT Device Family: TPS2595xx eFuse Series Manufacturer: Texas Instruments Marking Code: ES40 Functional Classification Device Type: Integrated eFuse with hot-swap and power rail protection Internal FET: Integrated N-channel MOSFET power switch FET On-Resistance: Ultra-low on-resistance class for minimal conduction loss Protection Class: Fast overvoltage protection clamping variant Electrical Characteristics Input Voltage Range: Wide input range, compatible with common low-voltage DC bus rails Current Limit Range: Adjustable programmable range via single external resistor Overvoltage Clamp Response Time: Fast response, microsecond-class clamping speed Output Slew Rate Control: Adjustable via single external capacitor for inrush current management Load Current Monitor: Analog output proportional to load current Enable & Logic Configuration Enable Input: Active high enable input Undervoltage Lockout: Adjustable UVLO threshold via external resistor divider Input Undervoltage Protection: Fixed internal threshold for power path enable gating Protection Features Overvoltage Protection: Fast clamp with factory-set clamping voltage option Overcurrent Protection: Programmable current limit with precision threshold setting Inrush Current Control: Soft-start slew rate control via external capacitor Thermal Shutdown: Integrated overtemperature protection with automatic recovery Reverse Current Blocking: Input undervoltage-triggered FET turn-off Certification & Compliance UL Recognition: UL 2367 recognized — File No. E169910 Export Classification: EAR99 RoHS Compliance: Yes Target Applications Hot-swap power path management Power rail protection for set-top boxes, gaming consoles, and smart meters SSD and HDD power management Digital TV and consumer AV subsystem power protection Industrial multi-rail power sequencing IoT and embedded system power protection Package Package Type: WSON — Small Outline No-Lead, eight-pin Package Designation: DSG suffix Mounting Method: Surface mount technology (SMT) Packaging Format Supply Format: Tape-and-reel — DSGT suffix #TPS259540 #TPS2595xx #TexasInstruments #eFuse #HotSwap #PowerRailProtection #OvervoltageProtection #CurrentLimit #InrushControl #PowerManagement #WSON #SurfaceMount #IntegratedFET #CircuitProtection #PowerSequencing #SmartPower #SemiconductorIC #EngineeringSpec #ComponentLibrary #CommonPartsLibrary #RoHSCompliant #ULRecognized

Automotive CAN FD Transceiver – High-speed CAN FD transceiver compliant with ISO 11898-2:2016 for automotive ECUs, body electronics, industrial automation, motor control, battery management systems (BMS), and embedded communication networks. Supports Classical CAN and CAN FD communication with data rates up to 8 Mbps, operating from a 4.5 V to 5.5 V supply. Features standby mode with ultra-low power consumption, ±58 V bus fault protection, TXD dominant timeout, thermal shutdown, undervoltage protection, 100 mV receiver hysteresis, and failsafe operation for robust and reliable CAN communication. Qualified to AEC-Q100 Grade 1, it operates over a −40°C to +125°C junction temperature range and is housed in a standard 8-pin SOIC package. Unlike the TCAN1462VDRBRQ1, this version does not include Signal Improvement Capability (SIC), making it suitable for conventional CAN/CAN FD networks. #TexasInstruments #TCAN1462VDRQ1 #TCAN1462Q1 #CANFD #CANTransceiver #AutomotiveElectronics #IndustrialCommunication #BatteryManagement #AECQ100 #SOIC8 #EmbeddedSystems