Automotive Nano-Power Precision Window Watchdog Timer – Automotive-grade precision window watchdog timer for automotive ECUs, ADAS, industrial controllers, safety-critical embedded systems, and microcontroller supervision. Operates from a 1.04 V to 6.0 V supply with an ultra-low 250 nA typical quiescent current, making it ideal for always-on and battery-powered applications. Features a programmable precision window watchdog with ±10% timing accuracy, factory-programmed or capacitor-programmable watchdog timeout (1 ms to 100 s), programmable reset delay (2 ms to 10 s), watchdog startup delay, open-window to close-window ratio selection (1× to 511×), manual reset (MR) support, latched or non-latched fault output, and open-drain active-low watchdog output for reliable system monitoring. Qualified to AEC-Q100 Grade 1, it operates over a −40°C to +125°C ambient temperature range and is housed in a compact 8-pin TSOT-23 (DDF) package. #TexasInstruments #TPS3436BFACADDFRQ1 #TPS3436Q1 #WatchdogTimer #WindowWatchdog #SupervisorIC #SystemMonitor #FunctionalSafety #AutomotiveElectronics #AECQ100 #TSOT238 #EmbeddedSystems

Single cell, 0.8A Li-Ion/Li-Po linear charge management controller, up to 30V input, 4.2V charge voltage, Open-Drain Status Output, Temperature sense input, SOT-23-6 1-cell battery charger lithium SOT?23*

Single cell, Li-Ion/Li-Po charge management controller, 4.20V, Open-Drain Status Output, in SOT23-5 package battery charger lithium SOT?23*

2-Bit Bidirectional Voltage-Level Shifter for Open-Drain and Push-Pull Application, X2SON-8 Level-Shifter CMOS-TTL-Translation X2SON*1.4x1mm*P0.35mm*

48-V, 16-bit ultra-precise current, voltage, and power monitor with I²C/SMBus interface and open-drain alert; INA236A address variant in 8-pin DDF SOT-23-THIN package.

Comparator General Purpose Open-Collector, Open-Drain 20-LCCC (8.89x8.89) #commonpartslibrary #integratedcircuit #linearcomparator

2-Bit Bidirectional Voltage-Level Shifter for Open-Drain and Push-Pull Application, VSSOP-8 Level-Shifter CMOS-TTL-Translation VSSOP*2.3x2mm*P0.5mm*

2-Bit Bidirectional Voltage-Level Shifter for Open-Drain and Push-Pull Application, SSOP-8 Level-Shifter CMOS-TTL-Translation SSOP*2.95x2.8mm*P0.65mm*

1-Bit Bidirectional Voltage-Level Shifter for Open-Drain and Push-Pull Application, SOT-23 Level-Shifter CMOS-TTL-Translation SOT?23*

Supervisor Open Drain or Open Collector 1 Channel TSOT-23-8 TPS3436CFDBEDDFRQ1 – Automotive precision window watchdog timer that monitors system operation by supervising watchdog timing and asserting a reset output when timing faults occur. It operates from a 1.04 V to 6.0 V supply, draws 250 nA typical quiescent current, supports factory-programmed or user-programmable watchdog timeout and reset delay, and provides active-low open-drain or push-pull outputs with watchdog enable/disable, startup delay, manual reset, and latched output options. #TexasInstruments #TPS3436CFDBEDDFRQ1 #WatchdogTimer #WindowWatchdog #AutomotiveIC #VoltageSupervisor #ResetSupervisor #NanoPower #EmbeddedSystems #PCBComponents

The TPS6216x device family are easy to use synchronous step-down DC/DC converters optimized for applications with high power density. A high switching frequency of typically 2.25 MHz allows the use of small inductors and provides fast transient response as well as high output voltage accuracy by utilization of the DCS-Control™ topology. With its wide operating input voltage range of 3 V to 17 V, the devices are ideally suited for systems powered from either a Li-Ion or other battery as well as from 12-V intermediate power rails. It supports up to 1-A continuous output current at output voltages between 0.9 V and 6 V (with 100% duty cycle mode). Power sequencing is also possible by configuring the enable and open-drain power good pins. In power save mode, the devices show quiescent current of about 17 μA from VIN. Power save mode, entered automatically and seamlessly if the load is small, maintains high efficiency over the entire load range. In shutdown mode, the device is turned off and shutdown current consumption is less than 2 μA. The device, available in adjustable and fixed output voltage versions, is packaged in an 8-pin WSON package measuring 2.00 mm × 2.00 mm (DSG) or 8- pin VSSOP package measuring 3.00 mm x 3.00 mm (DGK) • DCS-Control™ Topology • Input Voltage Range from 3 V to 17 V • Up to 1-A Output Current • Adjustable Output Voltage From 0.9 V to 6 V • Fixed Output Voltage Versions • Seamless Power Save Mode Transition • Typically 17-µA Quiescent Current • Power Good Output • 100% Duty Cycle Mode • Short Circuit Protection • Over Temperature Protection • Pin to Pin Compatible With TPS62170 and TPS62125 • Available in 3.00 mm x 3.00 mm 8-Pin VSSOP and 2.00 mm × 2.00 mm 8-Pin WSON Packages • Create a Custom Design using the TPS62160 with the WEBENCH® Power Designer #CommonPartsLibrary #IntegratedCircuit #PowerManagement #Voltage-regulator #switching-regulator

Buck Switching Regulator IC Positive Fixed 3.3V 1 Output 1A 8-WFDFN Exposed Pad The TPS6216x device family are easy to use synchronous step-down DC/DC converters optimized for applications with high power density. A high switching frequency of typically 2.25 MHz allows the use of small inductors and provides fast transient response as well as high output voltage accuracy by utilization of the DCS-Control™ topology. With its wide operating input voltage range of 3 V to 17 V, the devices are ideally suited for systems powered from either a Li-Ion or other battery as well as from 12-V intermediate power rails. It supports up to 1-A continuous output current at output voltages between 0.9 V and 6 V (with 100% duty cycle mode). Power sequencing is also possible by configuring the enable and open-drain power good pins. In power save mode, the devices show quiescent current of about 17 μA from VIN. Power save mode, entered automatically and seamlessly if the load is small, maintains high efficiency over the entire load range. In shutdown mode, the device is turned off and shutdown current consumption is less than 2 μA. The device, available in adjustable and fixed output voltage versions, is packaged in an 8-pin WSON package measuring 2.00 mm × 2.00 mm (DSG) or 8- pin VSSOP package measuring 3.00 mm x 3.00 mm (DGK). • DCS-Control™ Topology • Input Voltage Range from 3 V to 17 V • Up to 1-A Output Current • Adjustable Output Voltage From 0.9 V to 6 V • Fixed Output Voltage Versions • Seamless Power Save Mode Transition • Typically 17-µA Quiescent Current • Power Good Output • 100% Duty Cycle Mode • Short Circuit Protection • Over Temperature Protection • Pin to Pin Compatible With TPS62170 and TPS62125 • Available in 3.00 mm x 3.00 mm 8-Pin VSSOP and 2.00 mm × 2.00 mm 8-Pin WSON Packages • Create a Custom Design using the TPS62160 with the WEBENCH® Power Designer #CommonPartsLibrary #IntegratedCircuit #PowerManagement

LED Driver IC 16 Output Linear PWM Dimming 25mA 28-TSSOP The PCA9685 is an I2C-bus controlled 16-channel LED controller optimized for Red/Green/Blue/Amber (RGBA) color backlighting applications. Each LED output has its own 12-bit resolution (4096 steps) fixed frequency individual PWM controller that operates at a programmable frequency from a typical of 24 Hz to 1526 Hz with a duty cycle that is adjustable from 0 % to 100 % to allow the LED to be set to a specific brightness value. All outputs are set to the same PWM frequency. Each LED output can be off or on (no PWM control), or set at its individual PWM controller value. The LED output driver is programmed to be either open-drain with a 25 mA current sink capability at 5 V or totem pole with a 25 mA sink, 10 mA source capability at 5 V. The PCA9685 operates with a supply voltage range of 2.3 V to 5.5 V and the inputs and outputs are 5.5 V tolerant. LEDs can be directly connected to the LED output (up to 25 mA, 5.5 V) or controlled with external drivers and a minimum amount of discrete components for larger current or higher voltage LEDs. The PCA9685 is in the new Fast-mode Plus (Fm+) family. Fm+ devices offer higher frequency (up to 1 MHz) and more densely populated bus operation (up to 4000 pF). Although the PCA9635 and PCA9685 have many similar features, the PCA9685 has some unique features that make it more suitable for applications such as LCD or LED backlighting and Ambilight: • The PCA9685 allows staggered LED output on and off times to minimize current surges. The on and off time delay is independently programmable for each of the 16 channels. This feature is not available in PCA9635. • The PCA9685 has 4096 steps (12-bit PWM) of individual LED brightness control. The PCA9635 has only 256 steps (8-bit PWM). • When multiple LED controllers are incorporated in a system, the PWM pulse widths between multiple devices may differ if PCA9635s are used. The PCA9685 has a programmable prescaler to adjust the PWM pulse widths of multiple devices. • The PCA9685 has an external clock input pin that will accept user-supplied clock (50 MHz max.) in place of the internal 25 MHz oscillator. This feature allows synchronization of multiple devices. The PCA9635 does not have external clock input feature. • Like the PCA9635, PCA9685 also has a built-in oscillator for the PWM control. However, the frequency used for PWM control in the PCA9685 is adjustable from about 24 Hz to 1526 Hz as compared to the typical 97.6 kHz frequency of the PCA9635. This allows the use of PCA9685 with external power supply controllers. All bits are set at the same frequency. • The Power-On Reset (POR) default state of LEDn output pins is LOW in the case of PCA9685. It is HIGH for PCA9635. #CommonPartsLibrary #IntegratedCircuit #PowerManagement