For testing simulator errors. Best not to use this in a real project.

Flashing LED SMD Diode RGB Diodo Rainbow Color Changing fast slow flash

The NE555 devices are precision timing circuits capable of producing accurate time delays or oscillation. In time-delay or monostable operating modes, the timed interval is controlled by a single external resistor and capacitor network. In the astable mode of operation, the frequency and duty cycle are controlled independently with two external resistors and a single external capacitor. Each timer has a trigger level equal to approximately one-third of the supply voltage and a threshold level equal to approximately two-thirds of the supply voltage. These levels can be altered by use of the control voltage pin (CONT). When the trigger input (TRIG) is less than the trigger level, the flip-flop is set and the output goes high. If TRIG is greater than the trigger level and the threshold input (THRES) is greater than the threshold level, the flip-flop is reset and the output is low. The reset input (RESET) overrides all other inputs and is used to initiate a new timing cycle. If RESET is low, the flip-flop is reset and the output is low. Whenever the output is low, a lowimpedance path is provided between the discharge pin (DISCH) and the ground pin (GND). Tie all unused inputs to an appropriate logic level to prevent false triggering. The output circuit is capable of sinking or sourcing current up to 200mA. Operation is specified for supplies of 5V to 15V. With a 5V supply, output levels are compatible with TTL inputs. Features - Timing from microseconds to hours - Astable or monostable operation - Adjustable duty cycle - TTL-compatible output can sink or source up to 200mA - On products compliant to MIL-PRF-38535, all parameters are tested unless otherwise noted. Applications - Pulse-shaping circuits - Missing-pulse detectors - Pulse-width modulators - Pulse-position modulators - Sequential timers - Pulse generators -F requency dividers - Industrial controls

USB-C (USB TYPE-C) USB 3.2 Gen 2 (USB 3.1 Gen 2, Superspeed + (USB 3.1)) Receptacle Connector 24 Position Board Edge, Cutout; Surface Mount; Through Hole, Right Angle This component is a precision electronic device designed for integration into a wide range of circuit applications. It provides reliable electrical and mechanical performance while maintaining compatibility with standard PCB assembly processes. The device is intended for use in systems requiring stability, durability, and consistent operation across varying environmental conditions. Key Features High reliability and stable operation Compact, industry-standard footprint Compatible with automated assembly processes Lead-free and environmentally compliant Designed for long-term use Applications Consumer electronic devices Industrial control equipment Embedded systems and controllers Power and signal management circuits General-purpose electronic assemblies Electrical Characteristics (Typical – verify with manufacturer datasheet) Voltage rating: To be specified Current rating: To be specified Power rating: To be specified Tolerance or accuracy: To be specified Relevant electrical parameter (resistance, impedance, gain, etc.): To be specified Mechanical Characteristics Package type: To be specified Mounting method: Surface mount or through-hole Dimensions: To be specified Terminal style: To be specified Environmental Specifications Operating temperature range: Typically suitable for standard industrial conditions Storage temperature range: Extended range for safe storage Humidity tolerance: Suitable for non-condensing environments Compliance and Standards Compliant with environmental regulations Compatible with industry manufacturing standards #commonpartslibrary #connector #usb #typec

555 Type, Timer/Oscillator (Single) IC 100kHz 8-PDIP NE555 DIP-8 through hole The NE555P is a classic and widely used precision timer IC manufactured by companies like Texas Instruments and others. It belongs to the popular 555 timer family and is designed for generating accurate time delays, oscillations, and pulse signals. The “P” variant refers to the PDIP (Plastic Dual In-line Package), making it ideal for through-hole mounting, breadboarding, and prototyping. NE555P PDIP-8 timer Internally, the NE555P consists of: Two comparators A flip-flop A discharge transistor A voltage divider network These blocks allow flexible configuration for timing and waveform generation. Key Features Timing & Operation Modes Monostable mode (one-shot pulse generation) Astable mode (continuous oscillator) Bistable mode (flip-flop operation) Electrical Characteristics Supply voltage range: 4.5V to 16V Output can source or sink up to 200 mA Adjustable duty cycle Performance High timing accuracy and stability Timing range from microseconds to hours (depends on external R and C) Temperature-stable operation Package & Usability 8-pin DIP (through-hole) package Easy to use for: Breadboards DIY electronics Educational projects Common Applications LED flashers and blinkers Pulse generation Time delay circuits PWM control (e.g., dimming LEDs, motor speed control) Tone/sound generation #Timer #commonpartslibrary

Battery Holder (Open) 9V 1 Cell PC Pin 9V battery holder through hole The BH9VPC is a through-hole, printed circuit board–mount battery holder designed to accommodate a single standard 9 V (PP3) battery. It provides a secure mechanical enclosure and reliable electrical interface for powering electronic assemblies directly from a PCB. The holder is constructed from durable insulating material with integrated metal contacts to ensure stable retention and consistent electrical connection during operation. Its form factor supports straightforward integration into compact designs while maintaining ease of battery replacement. Engineering Specification: The component is intended for through-hole mounting using PC pins that provide both mechanical stability and electrical connection to the circuit board. It supports one 9 V battery with standard snap terminal interface internally routed to PCB pins. The housing material is typically molded plastic with good mechanical strength and electrical insulation properties suitable for general electronic applications. Contact terminals are metal, commonly nickel-plated or equivalent, to ensure low contact resistance and corrosion resistance over repeated battery insertions. The holder is designed for vertical mounting orientation relative to the PCB, with a compact footprint suitable for space-constrained layouts. It provides sufficient retention force to secure the battery under normal handling and vibration conditions encountered in consumer and light industrial electronics. The operating characteristics are aligned with typical 9 V battery usage, supporting low to moderate current applications depending on battery capability. The part is compatible with standard wave soldering processes used in through-hole assembly. It is intended for use in ambient environmental conditions typical of indoor electronic equipment and is not inherently sealed against moisture or contaminants. The design allows easy manual insertion and removal of the battery without specialized tools, supporting maintenance and replacement in field applications. #commonpartslibrary #batteryholder

Tactile Switch SPST-NO Top Actuated Surface Mount The B3FS-1002P is a compact, surface-mount tactile switch designed for low-profile input applications. It provides a momentary contact mechanism with a distinct tactile feedback, making it suitable for user interface controls in consumer electronics, industrial devices, and compact embedded systems. The switch features a sealed construction for improved reliability and is optimized for automated PCB assembly processes. Mechanical Characteristics Mounting Type: Surface Mount (SMD) Actuator Style: Top push Actuator Height: Low profile Outline: Rectangular compact body Terminal Type: Gull-wing terminals Sealing: Dust-resistant (sealed construction) Electrical Characteristics Switch Type: Single Pole Single Throw (SPST) Contact Configuration: Normally Open (NO) Rated Voltage: Low voltage DC applications Rated Current: Suitable for signal-level switching Contact Resistance: Low initial contact resistance Insulation Resistance: High insulation resistance between terminals Operating Characteristics Operating Force: Standard tactile force (manufacturer-defined variant) Travel Distance: Short stroke tactile action Operating Life: High durability for repeated actuation cycles Bounce Time: Minimal contact bounce for reliable switching Environmental Characteristics Operating Temperature Range: Wide operating range suitable for consumer and industrial use Storage Temperature Range: Standard electronic component storage conditions Humidity Resistance: Designed to withstand typical ambient humidity conditions Material & Construction Actuator Material: High-strength polymer Housing Material: Heat-resistant plastic Contact Material: Metal alloy with surface plating for durability Terminal Finish: Solderable finish compatible with reflow soldering Packaging Information Packaging Type: Tape and reel Assembly Compatibility: Fully compatible with automated pick-and-place and reflow processes Applications Consumer electronics (keypads, remote controls) Industrial control panels Portable devices Embedded system user interfaces Wearable and compact electronics #commonpartslibrary #switch #tactile

RP2040 chip for Raspberry Pi Pico - ARM® Cortex®-M0+ MCU 32-Bit The RP2040 is a high-performance, low-cost microcontroller built around two ARM Cortex-M0+ cores. It is optimized for flexibility, ease of use, and deterministic real-time performance. Unlike many microcontrollers, it includes a unique programmable I/O subsystem (PIO), allowing custom hardware interfaces without extra components. Key Features Processing Dual-core ARM Cortex-M0+ processors Up to 133 MHz clock speed Efficient integer performance with low power consumption Memory 264 KB on-chip SRAM External QSPI flash support (typically 2 MB–16 MB depending on board) Programmable I/O (PIO) 2 PIO blocks, each with 4 state machines Enables custom protocols (e.g., SPI, I2C, UART, WS2812, VGA, etc.) Offloads timing-critical tasks from CPU 🔗 Connectivity Interfaces 2× UART 2× SPI 2× I2C USB 1.1 controller (device or host support) 16× PWM channels Analog Features 12-bit ADC (up to 5 channels, including internal temperature sensor) Power & Voltage Operating voltage: 1.8V – 3.3V Low-power modes available Package Options QFN-56 (7×7 mm) Development Ecosystem Supports C/C++ SDK MicroPython and CircuitPython support Strong community and documentation Typical Applications Embedded systems and IoT devices Robotics and automation DIY electronics and prototyping USB devices (HID, MIDI, etc.) Custom communication interfaces using PIO #CommonPartsLibrary #IntegratedCircuit #Microcontroller

MAX98357A Series 5.5V 3.2W PCM Input Class D Audio Power Amplifier - TQFN-16 The MAX98357A/MAX98357B is an easy-to-use, low-cost, digital pulse-code modulation (PCM) input Class D amplifier that provides industry-leading Class AB audio performance with Class D efficiency. The digital audio interface automatically recognizes up to 35 different PCM and TDM clocking schemes which eliminates the need for I2C programming. Operation is further simplified by eliminating the need for an external MCLK signal that is typically used for PCM communication. Simply supply power, LRCLK, BCLK, and digital audio to generate audio! Furthermore, a novel pinout allows customers to use the cost-effective WLP package with no need for expensive vias (refer to Application Note 6643: Optimize Cost, Size, and Performance with MAX98357 WLP for more information). The digital audio interface is highly flexible with the MAX98357A supporting I2S data and the MAX98357B supporting left-justified data. Both ICs support 8 channel time division multiplexed (TDM) data. The digital audio interface accepts specified sample rates between 8kHz and 96kHz for all supported data formats. The ICs can be configured to produce a left channel, right channel, or (left/2 + right/2) output from the stereo input data. The ICs operate using 16/24/32-bit data for I2S and left-justified modes as well as 16-bit or 32-bit data using TDM mode. The ICs eliminate the need for the external MCLK signal that is typically used for PCM communication. This reduces EMI and possible board coupling issues in addition to reducing the size and pin count of the ICs. The ICs also feature a very high wideband jitter tolerance (12ns typ) on BCLK and LRCLK to provide robust operation. Active emissions-limiting, edge-rate limiting, and overshoot control circuitry greatly reduce EMI. A filterless spread-spectrum modulation scheme eliminates the need for output filtering found in traditional Class D devices and reduces the component count of the solution. The ICs are available in 9-pin WLP (1.345mm x 1.435mm x 0.64mm) and 16-pin TQFN (3mm x 3mm x 0.75mm) packages and are specified over the -40°C to +85°C temperature range. ● Single-Supply Operation (2.5V to 5.5V) ● 3.2W Output Power into 4Ω at 5V ● 2.4mA Quiescent Current ● 92% Efficiency (RL = 8Ω, POUT = 1W) ● 22.8μVRMS Output Noise (AV = 15dB) ● Low 0.013% THD+N at 1kHz ● No MCLK Required ● Sample Rates of 8kHz to 96kHz ● Supports Left, Right, or (Left/2 + Right/2) Output ● Sophisticated Edge Rate Control Enables Filterless Class D Outputs ● 77dB PSRR at 1kHz ● Low RF Susceptibility Rejects TDMA Noise from GSM Radios ● Extensive Click-and-Pop Reduction Circuitry ● Robust Short-Circuit and Thermal Protection ● Available in Space-Saving Packages: 1.345mm x 1.435mm WLP (0.4mm Pitch) and 3mm x 3mm TQFN ● Solution Size with Single Bypass Capacitor is 4.32mm2 Applications ● Single Li-ion Cell/5V Devices ● Smart Speakers ● Notebook Computers ● IoT Devices ● Gaming Devices (Audio and Haptics) ● Smartphones ● Tablets ● Cameras #commonpartslibrary #integratedcircuit #linearamplifier #mono

Non-Isolated PoL Module DC DC Converter 1 Output 0.8 ~ 6V 10A 6V - 20V Input The LMZ22010TZ/NOPB is a compact, high-efficiency step-down (buck) DC-DC power module from Texas Instruments. It integrates a switching regulator, power MOSFETs, inductor, and compensation components into a single package, simplifying power supply design. This module is capable of delivering up to 10A output current with excellent thermal performance and minimal external components. It is intended for high power density applications such as industrial systems, telecommunications equipment, and embedded processing platforms. Manufacturer Information Manufacturer: Texas Instruments Part Number: LMZ22010TZ/NOPB Product Type: DC-DC Buck Power Module Key Features Integrated power module with inductor and controller Output current up to 10A Wide input voltage range High efficiency operation Adjustable output voltage Built-in protection features (thermal shutdown, overcurrent protection) Power-good output and enable control Requires minimal external components Electrical Characteristics Parameter Value Input Voltage Range 6 V to 20 V Output Voltage Range 0.8 V to 6 V (adjustable) Output Current Up to 10 A Switching Frequency ~500 kHz Efficiency Up to ~95% Operating Temperature Range -40°C to +125°C Package Information Package Type: TO-PMOD (Power Module) Mounting Type: Surface Mount Integrated inductor and power components Optimized for thermal performance Pin Configuration (Typical) Pin Name Description VIN Input supply voltage VOUT Regulated output voltage GND Ground EN Enable input FB Feedback for output adjustment PGOOD Power-good indicator Typical Applications Industrial automation systems Telecom and networking equipment FPGA / DSP / processor power rails Embedded systems Point-of-load regulation Design Considerations Ensure proper PCB layout for heat dissipation Use appropriate input/output capacitors External resistors required to set output voltage Consider airflow for high-current operation #commonpartslibrary #powersupply #dcdc #converter

10 µH Shielded Drum Core, Wirewound Inductor 7.5 A 30mOhm Max Nonstandard # Engineering Specification ## Product Name SRP1038A-100M ## General Description SRP1038A-100M is a shielded surface mount power inductor designed for use in high-efficiency DC-DC conversion and power management applications. The device is intended to support energy storage and current smoothing functions in switching regulator circuits, where stable inductance performance and low power loss are critical. The inductor utilizes a ferrite core construction with a shielded magnetic structure to minimize electromagnetic interference and reduce magnetic flux leakage. This enables improved circuit density and reduced noise coupling in compact electronic assemblies. The design is optimized for use in high current power conversion systems, including buck converters, point-of-load regulators, and distributed power architectures. The component is widely used in industrial, automotive, telecommunications, and embedded systems where reliable energy transfer, thermal stability, and efficient power delivery are required. Its surface mount form factor supports automated PCB assembly and compact system integration while maintaining mechanical robustness under thermal and electrical stress. The design emphasizes low direct current resistance, high current handling capability, and stable inductance behavior under load conditions. It is suitable for applications requiring efficient power conversion with minimal energy loss and stable electromagnetic performance. ## Functional Requirements ### Energy Storage The device shall store energy in a magnetic field during switching operation in power conversion circuits. ### Current Filtering The device shall smooth current ripple in switching regulator applications to maintain stable output conditions. ### Electromagnetic Shielding The device shall reduce electromagnetic interference through a shielded magnetic structure. ### Power Conversion Support The component shall support efficient operation in DC-DC conversion systems. ## Electrical Requirements ### Inductive Performance The device shall provide stable inductance characteristics suitable for power conversion and filtering applications. ### Low Loss Operation The inductor shall minimize resistive and core losses to improve overall system efficiency. ### High Current Capability The device shall support operation under elevated current conditions typical of switching power supplies. ### Thermal Stability The inductor shall maintain performance consistency under thermal loading and temperature variation. ## Mechanical Requirements ### Surface Mount Package The device shall be supplied in a surface mount configuration suitable for automated PCB assembly processes. ### Structural Integrity The component shall withstand mechanical stress during assembly, operation, and thermal cycling. ### PCB Integration The design shall support compact layout integration in multilayer printed circuit board systems. ## Environmental Requirements ### Operating Conditions The device shall operate reliably under conditions typical of industrial and embedded electronic systems. ### Thermal Performance The component shall maintain stable operation under continuous power cycling and heat generation. ### Storage and Handling The device shall retain structural and electrical integrity during storage, transportation, and handling. ## Quality Requirements ### Reliability The inductor shall provide consistent long-term performance under continuous electrical and thermal stress. ### Verification Electrical and thermal characteristics shall be validated through appropriate qualification and testing procedures. ### Compliance The product shall conform to applicable standards for magnetic components used in power electronics applications. ## Documentation Requirements Technical documentation shall include application guidance, layout recommendations for switching power designs, thermal considerations, electrical characteristics, and integration practices for DC-DC converter systems. ## Classification Tags #SRP1038A100M #PowerInductor #ShieldedInductor #SMDInductor #MagneticComponent #EnergyStorageInductor #DCDCConverter #BuckConverter #PowerElectronics #SMPSDesign #ElectromagneticCompatibility #EMIShielding #PCBDesign #ElectricalEngineering #EmbeddedPower #IndustrialElectronics #AutomotiveElectronics #CommonPartsLibrary #ComponentLibrary #EngineeringSpecification #PowerManagement #CircuitDesign #HighCurrentInductor

Audio D/A Converter ICs 2VRMS DirectPath Aud io Stereo DAC 20-TSSOP The PCM5102AQPWRQ1 specification defines the engineering requirements for an automotive-grade digital-to-analog audio converter integrated circuit intended for high-performance digital audio applications. The specification establishes the functional, electrical, mechanical, thermal, and quality requirements necessary to ensure reliable conversion of digital audio signals into high-fidelity analog outputs. It serves as the governing technical reference for component selection, system integration, manufacturing, verification, and quality assurance throughout the product lifecycle. The device is designed to provide high-resolution audio performance with low distortion, low noise, and stable operation under automotive environmental conditions. It is suitable for use in infotainment systems, digital audio processing equipment, communication systems, and other embedded electronic applications requiring reliable digital-to-analog signal conversion. Engineering Requirements The component shall be manufactured using qualified semiconductor fabrication processes and approved materials to ensure consistent electrical performance, mechanical integrity, and long-term reliability. The device shall comply with applicable automotive qualification requirements and maintain stable operation within its specified voltage, temperature, and environmental operating ranges. Electrical performance shall meet the specified requirements for signal integrity, dynamic range, total harmonic distortion, noise performance, and output accuracy. The package shall be compatible with standard surface-mount assembly processes and shall withstand soldering and handling conditions without degradation. Workmanship shall be free from physical defects, contamination, package damage, or manufacturing irregularities that could affect functionality or reliability. Inspection, testing, and validation shall be performed using calibrated equipment and controlled procedures to verify compliance with all applicable engineering and quality requirements. Any deviation from this specification shall require formal engineering evaluation, documented technical justification, and approved change authorization prior to implementation. Documentation Supporting documentation shall include engineering drawings, electrical specifications, qualification reports, material declarations, inspection records, manufacturing documentation, and revision-controlled technical files. All documentation shall be maintained in accordance with established engineering configuration management and quality control procedures. Revision Control Changes to this specification shall be managed through the formal engineering change control process. All revisions shall undergo technical review, validation, and approval to ensure continued compliance with design intent, automotive quality standards, and applicable regulatory requirements. #EngineeringSpecification #AutomotiveElectronics #DigitalToAnalogConverter #AudioEngineering #EmbeddedSystems #QualityAssurance #Semiconductor #EngineeringDocumentation #Compliance #CommonPartsLibrary #IntegratedCircuit #Data-Acquisition #ADCs #DACs #PCM5102

REL-MR- 12DC/21-21AU - Plug-in miniature power relay, with multi-layer gold contact, 2 changeover contacts, input voltage 12 V DC General Purpose Relay DPDT (2 Form C) 12VDC Coil Through Hole The Phoenix Contact 2961299 (REL-MR-12DC/21-21AU) is a plug-in miniature power relay designed for reliable switching in industrial automation, control panels, and interface applications. It features a 12 VDC monostable coil, 2 changeover (DPDT) contacts, and hard gold-plated AgNi contacts, making it suitable for switching low-level signals with high reliability. The relay is RT III sealed (wash-proof), ensuring protection against contaminants during PCB cleaning and harsh industrial environments. It is intended for use with compatible Phoenix Contact relay bases and accessories. Key Features 12 VDC monostable coil operation 2 changeover (DPDT) contacts Hard gold-plated AgNi contacts for reliable low-level signal switching RT III sealed (wash-proof) construction Mechanical life: up to 30 million operations 5 kV coil-to-contact isolation Fast operate and release times (typ. 7 ms / 3 ms) Designed for industrial control, PLC interfaces, automation, and switching applications Compatible with Phoenix Contact relay sockets and interface modules #PhoenixContact #Relay #PowerRelay #DPDTRelay #IndustrialAutomation #ControlPanel #PLC #InterfaceRelay #12VDC #ElectromechanicalRelay