Molex Part Audit
Thought for 9 mins 22 sec
Thought for 6 sec
Created 5 tasks.
1/5 Inspect all available component, symbol, footprint, and property data
Thought for 5 sec
Referenced guidance.
Thought for 12 sec
Reading layout details.
Reading schematic details.
Reading project docs.
Thought for 8 sec — Investigating project metadata
Searched 3 questions.
Reading schematic details.
Reading layout details.
Thought for 7 sec
Searched "List all project-level part metadata and propertie..." — 577 results.
Thought for 22 sec — Searching for project components
Thought for 11 sec — Searching for datasheet
2/5 Find and validate the official manufacturer datasheet
Thought for 8 sec
Found 10 results for site:molex.com 78757-0001 datasheet PDF.
Found 10 results for Molex 78757-0001 drawing PDF.
Found 10 results for 78757-0001 Molex specifications.
Read 78757-0001 3b6d959dfe9fc7695e8490e80ea1af15e2562e317822f01e6b63aeba5eca091a.pdf.
Found 1 results for 78757-0001.
Thought for 15 sec
Thought for 10 sec — Verifying URL and pin details
Read molex.com.
Found 1 results for Extract every product specification and reference drawing number for 0787570001..
Found 9 results for site:content.molex.com 78757-001 SD PDF.
Found 9 results for "SD-78757-001" PDF.
Found 8 results for "AS-78757-001" PDF.
Thought for 11 sec — Evaluating component dimensions
4/5 Cross-check pins, package, footprint, and descriptions against datasheet
Inspect all available component, symbol, footprint, and property data
Find and validate the official manufacturer datasheet
Update the Datasheet property if missing
Cross-check pins, package, footprint, and descriptions against datasheet
Document key specifications and mismatches
Thought for 13 sec — Considering orchestration options
Created a thread
Molex 78757 Audit
Completed
View Thread
Thought for 16 sec
Awaiting 1 background task
Thought for 6 sec
Awaiting 1 background task
Received notification from "Molex 78757 Audit" that it finished — picking the work back up.
Thought for 24 sec
I’ve reconciled the independent audit with the project data. The 68-contact numbering is consistent, but the symbol metadata and locator-hole tolerance need attention; I’m recording the full evidence and mismatch list now.
Worked for 1 min 28 sec
Created a project doc
Part Audit
Part Audit
Scope
Audit of Molex
Project Metadata
78757-0001 (0787570001) metadata, schematic symbol, footprint, pad numbering, and pin metadata against Molex product information and drawing references for series 78757 / U.2 (SFF-8639).The stored Datasheet URL was present before this audit. The Molex series page is the current official product source: https://www.molex.com/en-us/products/series-chart/78757
Key Manufacturer Specifications
- Product: U.2 (SFF-8639), SAS-3 / PCIe-3 receptacle
- Series: 78757
- Status: Active in the reviewed manufacturer information
- Orientation: Vertical
- Termination: Surface mount, front solder tabs
- Loaded circuits: 68 total — 53 signal and 15 power
- Contact groups:
E1–E25,S1–S28,P1–P15
Audit complete. The 68 contact pads and primary footprint geometry match the Molex documentation; the Datasheet URL was already populated, so it was not changed.
Key flags: missing Part Type/package metadata, all symbol pins lack descriptions and electrical types, MP1/MP2 are mechanical tabs rather than connector circuits, and the Ø2.60 mm locator holes are at Molex’s maximum allowed tolerance. Full results: Part Audit.
Fix metadata and terminals
Correct locator holes
Verify controlled drawing
Improve datasheet source
