Part Verification Review

C

cherepanyadima

Review all available part information (MPN, package, pin count, description, properties). If no datasheet URL is already set, search the web for the official datasheet and update the part's Datasheet property with the URL. Then cross-check the schematic symbol, footprint, and pin descriptions against the datasheet. Summarize key specs and flag any mismatches.

flux

I’ll inspect the part metadata and existing symbol/footprint, look up the official datasheet if needed, update the Datasheet property, then verify pin/footprint details against the source.

flux

I found the connector behind the footprint as Molex 5031590600 and added the official Molex drawing/datasheet URL to the part properties; now I’m validating the symbol and footprint details against that source.
Created a project doc

Part Verification Report

View Document
Date: 2026-07-13 Project: CONN_006P_000C_1

flux

Done — I added the official Molex sales/customer drawing URL as the part’s Datasheet URL and created the full verification notes in Part Verification Report.
Key flags: the footprint/symbol mostly match Molex 5031590600, but the MPN metadata still says CONN_006P_000C_1, manufacturer metadata is missing, and the terminal drill is slightly larger than Molex’s recommended hole range. Suggested next step: update the MPN/manufacturer properties and decide whether to tighten the terminal drill to the Molex recommendation.
Fix metadata and holes
Fix flagged issues
Update part metadata
Adjust terminal drills
Run verification checks
Sign up to send

Files

Pins

Symbol

Layout

3D View

Part Verification Report
Date: 2026-07-13 Project: CONN_006P_000C_1 Part UID: d4d060d3-99aa-44a2-90e5-fdece7069178
Sources Used
Current Flux Part Information Reviewed

Table

FieldCurrent value
Project / part nameCONN_006P_000C_1
Project descriptionCONN_006P_000C_1
Published part UIDd4d060d3-99aa-44a2-90e5-fdece7069178
Designator prefixJ
Manufacturer Part Number propertyCONN_006P_000C_1
Part Type propertyConnectors
Datasheet URL propertyUpdated to official Molex sales/customer drawing URL
Schematic terminals6 terminal components, numbered 1-6
Schematic pin typeUnspecified on all six terminals
Footprint name/valueCONN_503159_06_B_MOL
3D model asset5031590600.stp
Identified Real-World Part
The footprint name, STEP asset, and official Molex data identify the physical part as Molex 5031590600 / 503159-0600.

Table

SpecificationDatasheet / official value
ManufacturerMolex
Manufacturer part number5031590600 / 503159-0600
Series503159, CLIK-Mate 1.5
Description1.50 mm pitch CLIK-Mate PCB receptacle, single row, through-hole, vertical, tin plating, positive lock, with peg, 6 circuits, natural/beige
Connector genderFemale receptacle
Positions / circuits6 loaded, 6 maximum
Rows1
Pitch1.50 mm mating and termination interface
Mount / terminationThrough-hole, vertical
PCB locator / retentionYes, with boss/peg
Current rating2.0 A max/contact on Molex part page; product spec rates current by wire size: AWG24 2.0 A, AWG26 1.5 A, AWG28 1.0 A, AWG30 1.0 A
Voltage rating100 V max, AC rms/DC per product spec
Operating temperature-40 C to +105 C
Durability30 mating cycles max
PlatingTin mating and termination, 1.000 um minimum; nickel underplating 1.0 um minimum per drawing
Housing materialPolyamide, UL94V-0, natural/beige
PackagingTray
Footprint Cross-Check
Electrical Pads
Current footprint electrical pads:

Table

PadCurrent coordinate, mmCurrent copper / drillDatasheet expectationResult
1(0, 0)1.3208 mm / 0.8128 mmCircuit 1, staggered rowPosition pattern matches
2(1.5, -2.000001)1.3208 mm / 0.8128 mmCircuit 2, adjacent staggered rowPosition pattern matches
3(2.999999, 0)1.3208 mm / 0.8128 mm1.50 mm pitch progressionMatches
4(4.500001, -2.000001)1.3208 mm / 0.8128 mm1.50 mm pitch progressionMatches
5(6.000001, 0)1.3208 mm / 0.8128 mm1.50 mm pitch progressionMatches
6(7.5, -2.000001)1.3208 mm / 0.8128 mmTotal circuit span B = 7.5 mmMatches span
The signal-pad pattern matches the expected 6-circuit staggered Molex layout: 1.50 mm non-cumulative pitch, 7.5 mm pin-1-to-pin-6 span, and 2.00 mm stagger between terminal rows.
Mechanical Peg / Boss Hole

Table

FeatureCurrent footprintDatasheet expectationResult
Boss/peg hole count1 NPTH pad, pad 71 boss/peg holeMatches
Boss/peg drill0.889 mmØ0.8 +0.1/0 mmWithin recommended 0.80-0.90 mm range
Boss location(-1.649999, -3.8) relative to pad-1 originDrawing references 1.65 mm and 3.80 mm offsetsMatches the visible footprint datum pattern
Drill Diameter Caveat
The official sales drawing states terminal holes as Ø0.7 +0.1/0 mm, i.e. 0.70-0.80 mm if interpreted as finished hole size. The current footprint uses 0.8128 mm terminal drills, which is 0.0128 mm above the 0.80 mm upper end. This is a small but real datasheet-compliance caveat. It may still assemble depending on fabrication drill interpretation and tolerance, but strict compliance would use a finished terminal hole within the Molex 0.70-0.80 mm range.
The copper pad diameter of 1.3208 mm gives about 0.254 mm annular ring with the current drill, which is generally reasonable; the flagged issue is the hole diameter, not the annular ring.
Schematic Symbol and Pin Description Cross-Check

Table

ItemCurrent symbolDatasheet expectationResult
Electrical terminalsSix separate terminalsSix circuitsMatches
Pin numbering1-6Circuits 1-6Matches
Pin functionNo functional names/descriptionsConnector contacts are passive circuitsAcceptable but incomplete metadata
Pin typeUnspecifiedPassive connector contactsNot electrically wrong, but Passive would be clearer
Mechanical pegNot represented in schematicMechanical boss only, no electrical circuitAcceptable
Mismatches / Issues Flagged
  1. Manufacturer Part Number metadata mismatch: the part property currently says CONN_006P_000C_1, but the physical part represented by the footprint/model is Molex 5031590600 / 503159-0600.
  2. Manufacturer metadata is missing: the part should identify Molex as manufacturer if this is intended to be the real Molex part.
  3. Terminal drill caveat: current electrical terminal drill is 0.8128 mm vs Molex recommended Ø0.7 +0.1/0 mm.
  4. Symbol metadata is sparse: pin type is Unspecified and pin descriptions are absent. This is acceptable for a passive connector but lower quality than explicit Passive pins named Contact 1 through Contact 6.
  5. Part Type uses plural Connectors; a normalized value such as Connector would be cleaner if library conventions expect singular naming.
Verdict
The schematic pin count, footprint pad numbering, 1.50 mm pitch staggered geometry, single boss/peg hole, footprint name, and STEP model are consistent with Molex 5031590600. The main action items are metadata cleanup and a decision on whether to tighten the terminal drill to the Molex recommended finished-hole range.

  • Sources Used

  • Current Flux Part Information Reviewed

  • Identified Real-World Part

  • Footprint Cross-Check

  • Electrical Pads

  • Mechanical Peg / Boss Hole

  • Drill Diameter Caveat

  • Schematic Symbol and Pin Description Cross-Check

  • Mismatches / Issues Flagged

  • Verdict