Molex Datasheet Review

Review all available part information (MPN, package, pin count, description, properties). If no datasheet URL is already set, search the web for the official datasheet and update the part's Datasheet property with the URL. Then cross-check the schematic symbol, footprint, and pin descriptions against the datasheet. Summarize key specs and flag any mismatches.

Thought for 7 sec

flux

I’ll inspect the part metadata, find and set the official datasheet URL if it’s missing, then compare symbol/footprint/pin details against the datasheet and summarize any mismatches.

Worked for 7 mins 13 sec

Created a project doc

Part Datasheet Cross-Check: Molex 52271-3069

View Document

Date: 2026-07-17 Reviewed available part information in this Flux part project and cross-checked the schematic symbol, footprint, and pin me...

flux

Completed the datasheet review for Molex 52271-3069. The official Datasheet URL was already set, so I did not change it; the 30-contact signal footprint matches the datasheet well, but pin metadata is incomplete and the mounting-pad/keepout details need visual verification.

Detailed findings are in Part Datasheet Cross-Check: Molex 52271-3069.

Open items:

All symbol pins are still Unspecified and missing pin descriptions.
MP1/MP2 fitting-nail pads and no-footprint/keepout regions should be checked against the official Molex drawing before production use.

Suggested next steps:

Update pin types/descriptions for pins 1–30 and MP1/MP2.
Visually verify or revise MP1/MP2 pad geometry from the Molex recommended PCB pattern.
Add explicit connector keepouts/no-footprint areas if needed.

Fix metadata and verify

Update pin metadata

Verify MP pads

Add keepouts

Run ERC/DRC

Files

Pins

Symbol

Layout

3D View

Part Datasheet Cross-Check: Molex 52271-3069

Date: 2026-07-17

Scope

Reviewed available part information in this Flux part project and cross-checked the schematic symbol, footprint, and pin metadata against the official Molex datasheet/customer drawing.

Project Metadata Found

Table

Field	Project / indexed value	Datasheet / source check
Manufacturer Part Number	52271-3069	Matches Molex part 52271-3069 / 0522713069
Manufacturer	Molex	Matches
Part Type	Connectors	Matches FFC/FPC connector
Designator Prefix	J	Appropriate for connector
Mount	Surface Mount	Matches SMT/right-angle connector
Datasheet URL	https://www.molex.com/pdm_docs/sd/522713069_sd.pdf	Already present; no update required
Product URL	Not found as a project-level property	Official product detail commonly appears as https://www.molex.com/en-us/products/part-detail/0522713069
Description	Not explicitly stored as project-level property	Easy-On FFC/FPC Connector, 1.00 mm Pitch, Slider Series, Right-Angle, Bottom Contact, 3.00 mm Height, 30 Circuits, Gold Plating
Pin / pad count	30 signal terminals + MP1/MP2 mounting pads; 32 pads total	Matches 30 circuits plus two fitting nails / hold-down pads

Key Datasheet Specs

Table

Spec	Value
Series / drawing	Molex 52271, customer drawing SD-52271-038, Rev G
Connector type	Easy-On FFC/FPC, ZIF slider
Orientation	Right angle
Contact style	Bottom contact
Circuits	30
Pitch	1.00 mm mating and termination interface
Mated height	3.00 mm
Current rating	0.5 A max per contact
Voltage rating	50 V max
Operating temperature	-40 °C to +85 °C
Durability	30 mating cycles max
Housing material	Nylon, UL94V-0
Actuator material	PPS, UL94V-0
Terminal material	Phosphor bronze, t=0.25 mm
Fitting nail material	Copper alloy, t=0.25 mm
Contact plating	Gold, 0.1 um min on contact portion; tin 1.0 um min on solder portion; nickel underplating 1.0 um min
Recommended FFC/FPC finished thickness	0.3 ± 0.05 mm
Coplanarity	Tail and fitting nail coplanarity 0.15 mm max

Schematic Symbol Cross-Check

Table

Item	Project state	Assessment
Signal terminals	Pins 1 through 30 present	Matches 30-circuit datasheet
Mounting pads	MP1 and MP2 present	Matches fitting nail / solder hold-down concept
Pin numbering	1-30 sequential; MP1/MP2 separate	Correct and clear
Pin Type	All terminals show `Unspecified`	Library-quality mismatch / incomplete metadata. Connector signal pins should normally be Passive or Bidirectional; MP1/MP2 should be Mechanical or Passive if Mechanical is unavailable.
Pin Description	No functional pin descriptions present	Incomplete. Suggested descriptions: `FFC/FPC contact N` for pins 1-30 and `Solder fitting nail / mechanical hold-down` for MP1/MP2.
Bottom-contact orientation note	Not represented in pin descriptions	Consider documenting bottom-contact orientation and pin-1/cable insertion direction in the symbol or part notes.

Footprint Cross-Check

Signal-contact pad array

Table

Datasheet expectation	Project footprint	Assessment
30 SMT signal pads	Pads 1-30 present	Matches
1.00 mm pitch	Pads positioned at x = -14.5 mm to +14.5 mm in 1.0 mm increments	Matches
Contact span `(N-1)` = 29.0 mm for 30 circuits	Project span = 29.0 mm	Matches
Recommended signal land width about 0.6 mm	Project pad width 0.600 mm	Matches
Recommended signal land length about 1.9 mm	Project pad length 1.900 mm	Matches
Pin-1 marking	Silk pin-1 dot near pad 1	Present

Fitting nail / mounting pads

Table

Datasheet evidence	Project footprint	Assessment
Fitting nails present for prevention of PCB pattern peeling	MP1/MP2 present	Matches conceptually
Extracted drawing values include 2.1 mm, 4.2 mm, 1.65 mm, 1.6 mm, 0.6 mm, 2.8 mm around fitting nail recommended pattern	MP pads at x = ±17.650 mm, y = -1.7 mm, size 2.100 mm × 2.800 mm	Needs manual visual confirmation against the Molex drawing. The extracted values may mix land sizes, positional references, and no-footprint-area dimensions. If 4.2 mm is the actual recommended land length, the current 2.8 mm MP pad length may be too short; if 2.8 mm is the actual land length and 4.2 mm is a reference span, the project may be correct.
Datasheet includes `NO FOOT PRINT AREA` note	Footprint contains pads, fab/silk/courtyard-like lines, but no explicit keepout/no-footprint-area rules were identified	Potential omission. Add/verify mechanical keepouts for actuator/FPC insertion and no-footprint zones before production use.

Mismatches / Issues Flagged

Pin metadata incomplete: all schematic terminals have Pin Type = Unspecified.
Pin descriptions missing: pins 1-30 and MP1/MP2 have no descriptive function text.
Mounting pad dimensions/position need visual verification: signal pads match well, but MP1/MP2 interpretation is ambiguous from OCR extraction of the Molex drawing.
No-footprint / keepout areas not explicitly modeled: the datasheet drawing includes no-footprint-area notes; project footprint does not show explicit keepout rules in the inspected layout data.
Product URL and human-readable description are not explicitly stored as project-level properties: datasheet-backed values are known, but not currently captured as metadata fields.

Conclusion

The core part identity and the 30-contact signal footprint appear correct against the official Molex drawing: count, pitch, span, and signal pad dimensions match. The main production-risk item is the fitting-nail / mounting-pad land pattern and associated keepout/no-footprint areas, which should be visually checked against the official Molex recommended PCB pattern before relying on this footprint for fabrication. The symbol is functionally complete in pin count but needs better pin types and descriptions for library quality.

Scope
Project Metadata Found
Key Datasheet Specs
Schematic Symbol Cross-Check
Footprint Cross-Check
Signal-contact pad array
Fitting nail / mounting pads
Mismatches / Issues Flagged
Conclusion