10/100 Base-T/TX PHY Ethernet controller that supports PoE with SPI Interface. Based on W5500. Can be used as PoE injector. #project #referenceDesign #template #w5500 #PoE #EtherNet #RJ5

OctoPower is a monitoring hardware, it provides an end-to-end electricity monitoring solution perfect for monitoring home consumption, solar generation or any AC electrical circuit for that matter. Key features : - 8x clip-on CT current sensor - Full Real/Active power measurement & continuous sampling. - Cumulative energy persisted on reboot. - Wifi (with WPS) and Ethernet support - It send all data on mqtt topic - It can be configurable mqtt topics, calibration, enable/disable wifi over a mqtt api - Upgrade firmware over local network

It is a board based on STM32L4 with a built-in ethernet IC W5500 that allows you to create IoT projects based on the modern ARM Cortex®-M4 core. A connector with SWD interface and USB C for communication are provided for the firmware #IoT #ARM #STM #Ethernet #W5500 #IC #project

An I2C extension shield with 6 shielded ethernet ports and a TCA9548 breakout board. This board is for the target side, any microcontroller with a standard Arduino header can use it. With proper target side hardware and an SSTP ethernet cable, the board provides robust i2c communication over 10ft(could be longer, haven't tested it yet) with a bitrate of 400kHz under a noisy environment( near motors, power cables, switches, etc). The shield board provides power to the target side and can power the i2c device. The board also supports drdy trigger, which is available on many i2c sensors. The TCA9548 breakout board is for a scenario in which all of your i2c devices have the same address. #Arduino #Uno #Shield #Template #project-template #project

Simple Ethernet board used WIZ550 with real MAC address and configures the network setting automatically.

2U 10-inch rackmount 12V distribution power supply for Dell server PSUs, with 12 managed boost-module slots, per-slot current monitoring, temperature logging, MCU supervision, and optional Ethernet metrics.

Industrial Raspberry Pi CM4/CM5-compatible carrier for PoE-powered inspection image capture and cryptographic signing with TPM, RTC, CSI camera, Ethernet, and three TMC2209 stepper axes.

Industrial 100 mm x 80 mm 6-layer RK3588S compute-module carrier for the Sovereign Edge Aggregator, targeting Radxa CM5-class SoM, CrossLink-NX Ring Zero FPGA, ATECC608B trust anchor, INA260 energy metering, NVMe, dual Gigabit Ethernet, and controlled-impedance routing.

10/100 Base-T/TX PHY Ethernet controller that supports PoE with SPI Interface. Based on W5500. Can be used as PoE injector. #project #referenceDesign #template #w5500 #PoE #EtherNet #RJ5

It is a board based on STM32L4 with a built-in ethernet IC W5500 that allows you to create IoT projects based on the modern ARM Cortex®-M4 core. A connector with SWD interface and USB C for communication are provided for the firmware #IoT #ARM #STM #Ethernet #W5500 #IC #project

Industrial-grade RP2350B controller with W5500 Ethernet, 24V input power, isolated industrial I/O, RS485, USB hub, relay outputs, and robust connector protection for -40°C to +85°C consumer/industrial use.

Welcome to your new project. Imagine what you can build here.

Welcome to your new project. Imagine what you can build here.

Welcome to your new project. Imagine what you can build here.

Welcome to your new project. Imagine what you can build here.

Software: Linux Power Requirements: LiPo battery powered Compliance: RoHS Connectivity: USB, WiFi, Bluetooth, Ethernet Human Interface: Joystick, Display Operating Voltage: 3.3V, 5V, 9V Operating Temp: -40 to +85C Reliability: 10,000hrs MTBF Target Cost: $100

An I2C extension board with LTC4311 bus accelerator and shielded ethernet port. This board is for the target side. With proper controller side hardware and an SSTP ethernet cable, the board provides robust i2c communication over 10ft(could be longer, haven't tested it yet) with a bitrate of 400kHz under a noisy environment( near motors, power cables, switches, etc). The breakout board receives power from the controller side and can power i2c device. The board also supports drdy trigger, which is available on many i2c sensors. #project #I2C #shielded #robust #ltc4311 #long-distance

this is a custom board using the MCU "STM32F107RBTx". the reason why i chose this MCU is because i wanted to implement circuits for ethernet communication, CAN communication and USB communication.

10/100 Base-T/TX PHY Ethernet controller that supports PoE with SPI Interface. Based on W5500. Can be used as PoE injector. #project #referenceDesign #template #w5500 #PoE #EtherNet #RJ5

10/100 Base-T/TX PHY Ethernet controller that supports PoE with SPI Interface. Based on W5500. Can be used as PoE injector. #project #referenceDesign #template #w5500 #PoE #EtherNet #RJ5

10/100 Base-T/TX PHY Ethernet controller that supports PoE with SPI Interface. Based on W5500. Can be used as PoE injector. #project #referenceDesign #template #w5500 #PoE #EtherNet #RJ5

10/100 Base-T/TX PHY Ethernet controller that supports PoE with SPI Interface. Based on W5500. Can be used as PoE injector. #project #referenceDesign #template #w5500 #PoE #EtherNet #RJ5

An I2C extension shield with 6 shielded ethernet ports and a TCA9548 breakout board. This board is for the target side, any microcontroller with a standard Arduino header can use it. With proper target side hardware and an SSTP ethernet cable, the board provides robust i2c communication over 10ft(could be longer, haven't tested it yet) with a bitrate of 400kHz under a noisy environment( near motors, power cables, switches, etc). The shield board provides power to the target side and can power the i2c device. The board also supports drdy trigger, which is available on many i2c sensors. The TCA9548 breakout board is for a scenario in which all of your i2c devices have the same address. #Arduino #Uno #Shield #Template #project-template #project

10/100 Base-T/TX PHY Ethernet controller that supports PoE with SPI Interface. Based on W5500. Can be used as PoE injector. #project #referenceDesign #template #w5500 #PoE #EtherNet #RJ5

10/100 Base-T/TX PHY Ethernet controller that supports PoE with SPI Interface. Based on W5500. Can be used as PoE injector. #project #referenceDesign #template #w5500 #PoE #EtherNet #RJ5