Automotive, 60-V, 6-A, 30-mΩ, one-channel smart high-side switch with adjustable current limit TPS1HTC30-Q1 is a single-channel, smart high-side switch, with integrated NMOS power FET and charge pump, designed to meet the requirements of 24-V automotive battery systems. The low RON(30 mΩ) minimizes device power dissipation driving a wide range of output load current up to 6-A DC, and the 60- V DC operating range improves system robustness. The device integrates protection features such as thermal shutdown, output clamp, and current limit. These features improve system robustness during fault events such as short circuit. TPS1HTC30-Q1 implements an adjustable current limiting circuit that improves the reliability of the system by reducing inrush current when driving large capacitive loads and minimizing overload current. The device also provides an accurate load current sense that allows for improved load diagnostics such as overload and open-load detection enabling better predictive maintenance. TPS1HTC30-Q1 is available in a small 14-pin, 4.40- mm × 5.0-mm HTSSOP leaded package with 0.65- mm pin pitch minimizing the PCB footprint. • Single-channel smart high-side power switch for 24-V automotive systems with full diagnostics • Wide operating voltage range: 6 V to 60 V – OVP protection: 66 V • Low RON: 30-mΩ typical, 55-mΩ maximum • Low standby current: < 0.5 µA • Low quiescent current (Iq): < 2 mA • Improve system level reliability through adjustable current limiting – Current limit: 2 A –16 A • Accurate current sensing: ±4% at 1 A • Protection – Overload and short-circuit protection – Integrated inductive discharge clamp – Undervoltage lockout (UVLO) protection – Loss of GND, loss of supply protection – Reverse battery protection with external components • Diagnostics – On and off state output open-load and short-tobattery detection – Overload and short to ground detection – Absolute and relative thermal shutdown detection • Functional Safety-Capable – Documentation available to aid functional safety system design • Operating junction temperature: –40 to 125°C • Input control: 1.8-V, 3.3-V and 5-V logic compatible • Integrated fault sense voltage scaling for ADC protection • Qualifications – AEC-Q100 qualified for automotive applications • Temperature grade 1: –40°C to +125°C, TA • 14-pin thermally-enhanced TSSOP package TPS1HTC30AQPWPRQ1 #CommonPartsLibrary #IntegratedCircuit

Single-channel high-speed low-side MOSFET/IGBT gate driver with 4-A source/8-A sink, split outputs for independent turn-on/off control, dual inverting/noninverting inputs, 4.5–18 V supply, 13 ns typical delay, and UVLO in SOT-23-6.

Buck Switching Regulator IC Positive Fixed 3.3V 1 Output 2A SOT-23-6 Thin, TSOT-23-6 The AP63200/AP63201/AP63203/AP63205 is a 2A, synchronous buck converter with a wide input voltage range of 3.8V to 32V and fully integrates a 125mΩ high-side power MOSFET and a 68mΩ low-side power MOSFET to provide high-efficiency step-down DC/DC conversion. The AP63200/AP63201/AP63203/AP63205 device is easily used by minimizing the external component count due to its adoption of peak current mode control along with its integrated compensation network. The AP63200/AP63201/AP63203/AP63205 has optimized designs for Electromagnetic Interference (EMI) reduction. The converter features Frequency Spread Spectrum (FSS) with a switching frequency jitter of ±6%, which reduces EMI by not allowing emitted energy to stay in any one frequency for a significant period of time. It also has a proprietary gate driver scheme to resist switching node ringing without sacrificing MOSFET turn-on and turn-off times, which further erases highfrequency radiated EMI noise caused by MOSFET switching. The device is available in a low-profile, TSOT26 package. • VIN 3.8V to 32V • 2A Continuous Output Current • 0.8V ±1% Reference Voltage • 22µA Ultralow Quiescent Current • Switching Frequency o 500kHz: AP63200 and AP63201 o 1.1MHz: AP63203 and AP63205 • Pulse Width Modulation (PWM) Regardless of Output Load o AP63201 • Supports Pulse Frequency Modulation (PFM) o AP63200, AP63203, and AP63205 o Up to 80% Efficiency at 1mA Light Load o Up to 88% Efficiency at 5mA Light Load • Fixed Output Voltage o 3.3V: AP63203 o 5.0V: AP63205 • Proprietary Gate Driver Design for Best EMI Reduction • Frequency Spread Spectrum (FSS) to Reduce EMI • Precision Enable Threshold to Adjust UVLO • Protection Circuitry o Overvoltage Protection o Cycle-by-Cycle Peak Current Limit o Thermal Shutdown • 12V and 24V distributed power bus supplies • Flat screen TV sets and monitors • Power tools and laser printers • White goods and small home appliances • FPGA, DSP, and ASIC supplies • Home audios • Network systems • Set top boxes • Gaming consoles • Consumer electronics #commonpartslibrary #integratedcircuit #AP63203WU7 #BuckConverter #DCDCConverter #PowerManagement #VoltageRegulator #SynchronousBuck #EmbeddedSystems #IndustrialElectronics #PowerSupply #DiodesInc #3V3Power #ElectronicsDesign

High voltage half-bridge gate driver for GaN transistors Features • dV/dt immunity ±200 V/ns • Driver current capability: – 1.3/2.4 A source/sink typ @ 25 °C, 6 V – 5.5/6 A source/sink typ @ 25 °C, 15 V • Separated turn on and turn off gate driver pins • 45 ns propagation delay with tight matching • 3.3 V, 5 V TTL/CMOS inputs with hysteresis • Interlocking function • UVLO on low-side and high-side sections • Dedicated pin for shut down functionality • Over temperature protection Applications • High-voltage PFC, DC-DC and DC-AC converters • Switch-mode power supplies • UPS systems • Solar power • Motor driver for home appliances, factory automation and industrial drives. #CommonPartsLibrary #IntegratedCircuit #powermanagement

Buck Switching Regulator IC Positive Fixed 5V 1 Output 1A SOT-23-6 The LMR50410Y5FQDBVRQ1 (part of the LMR50410-Q1 family from Texas Instruments) is a synchronous step-down (buck) DC-DC converter designed for automotive and industrial power applications. It operates over a wide input voltage range of 4 V to 36 V and can deliver up to 1 A output current, making it suitable for converting higher, unregulated voltages into stable lower voltages (e.g., 5 V or 3.3 V rails). The device integrates power switches, control circuitry, and compensation internally, allowing simple design with minimal external components and a compact PCB footprint. Key Features Power & Performance Wide input voltage range: 4 V to 36 V Output current: up to 1 A High switching frequency: 2.1 MHz (enables small inductors) High efficiency with PFM (light load) and FPWM (constant frequency) options Integration & Ease of Use Synchronous rectification (integrated high-side & low-side MOSFETs) Internal compensation (no complex external tuning) Minimal external components required Small SOT-23-6 package for compact designs Protection & Reliability Cycle-by-cycle current limit Short-circuit protection (hiccup mode) Thermal shutdown protection Undervoltage lockout (UVLO) ±1% reference voltage accuracy Automotive & Industrial Capability AEC-Q100 qualified (automotive grade) Operating temperature: Ambient: up to 125°C Junction: up to 150°C Designed for rugged automotive environments Additional Features Soft-start for controlled startup Precision enable pin for system control Monotonic startup with pre-biased output Available in fixed output (e.g., 5 V) variants Typical Applications Automotive electronics (ADAS, infotainment, lighting) Industrial power supplies Distributed power systems General-purpose DC-DC regulation #commonpartslibrary #integratedcircuit #powermanagement #voltageregulator

Linear Voltage Regulator IC Positive Fixed 1 Output 500mA SOT-23-5 The TLV75533PDBVR is a low-dropout (LDO) linear voltage regulator designed to provide a stable 3.3 V output from a higher input voltage source. It features ultra-low quiescent current and high power-supply rejection ratio (PSRR), making it ideal for battery-powered and noise-sensitive applications such as IoT devices, portable electronics, and RF circuits. The device is optimized for fast transient response and stable operation with small ceramic output capacitors. Key Features Fixed output voltage: 3.3 V Low dropout voltage (typ. ~200 mV at full load) Ultra-low quiescent current (typ. 25 µA) High PSRR for noise-sensitive applications Stable with small ceramic capacitors (≥1 µF) Thermal shutdown and overcurrent protection Available in compact SOT-23-5 package (DBV) Absolute Maximum Ratings Input voltage: –0.3 V to 6.5 V Output voltage: –0.3 V to (VIN + 0.3 V) Operating junction temperature: –40°C to +125°C Storage temperature range: –65°C to +150°C Recommended Operating Conditions Input voltage range: 1.45 V to 5.5 V Output voltage: 3.3 V (fixed) Output current: up to 500 mA Operating temperature range: –40°C to +125°C Electrical Characteristics (Typical unless otherwise noted) Output voltage accuracy: ±1% Dropout voltage: ~200 mV @ 500 mA Quiescent current: ~25 µA PSRR: up to 70 dB (at 1 kHz) Line regulation: <0.05%/V Load regulation: <0.5% Pin Configuration (SOT-23-5) Pin 1: IN – Input voltage Pin 2: GND – Ground Pin 3: EN – Enable (active high) Pin 4: NC – No connect Pin 5: OUT – Regulated output Typical Application Power management for microcontrollers and sensors Battery-powered portable devices RF and analog circuits requiring low noise supply IoT and wearable electronics Protection Features Thermal shutdown protection Overcurrent protection Undervoltage lockout (UVLO) #commonpartsLibrary #integratedcircuit #powermanagement #voltageregulator

Single-Channel EiceDRIVER With True Differential Inputs, 4V UVLO, +4/-8A, SOT-23-6 Driver, Dual MOSFET SOT?23*

3A 55V Boost Converter with Programmable Switching Frequency and UVLO #ultralibrarian

Ultra-Low IQ Synchronous Buck DC-DC Converter – 300 mA synchronous step-down (buck) switching regulator for high-efficiency industrial, automotive, battery-powered, and embedded power applications. Operates from a 3 V to 65 V input voltage, provides an adjustable output voltage from 1.0 V to 65 V, and delivers up to 300 mA output current. Features 6 µA typical quiescent current, programmable switching frequency from 200 kHz to 2.2 MHz, 100% duty-cycle operation, synchronous rectification, Power Good (PG) output, enable input, soft-start, cycle-by-cycle current limiting, hiccup short-circuit protection, thermal shutdown, and undervoltage lockout (UVLO). Specified for operation over a −40°C to +150°C junction temperature range and housed in a 9-pin VQFN-HR (2 × 2 mm) wettable-flank package. #TexasInstruments #LMR36503RFRPER #LMR36503 #BuckConverter #SynchronousBuck #DCDCConverter #SwitchingRegulator #PowerManagement #UltraLowIQ #300mA #VQFN9 #EmbeddedSystems

Buck Switching Regulator IC Positive Adjustable 1.2V 1 Output 3.5A 8-PowerSOIC (0.154", 3.90mm Width) The LM5013DDAR is a 100-V input, 3.5-A buck switching regulator IC that efficiently steps down high DC voltages (such as 24 V, 48 V, or battery rails) to lower regulated outputs. It is optimized for rugged environments where wide input variations and high reliability are required. It features ultra-low quiescent current operation, making it suitable for systems that require high efficiency even at light load or standby conditions. Key Features Wide input voltage range: 6 V to 100 V Up to 3.5 A output current capability Integrated 100-V high-side MOSFET Non-synchronous buck topology Ultra-low quiescent current (IQ) for high efficiency in standby Constant-on-time (COT) control for fast transient response No external compensation components required Adjustable output voltage (down to ~1.2 V reference) 50 ns minimum on/off time for high step-down ratios Built-in protection features: Overcurrent protection Thermal shutdown Input undervoltage lockout (UVLO) Open-drain power-good (PGOOD) signal for system monitoring Meets low EMI requirements (CISPR 25 Class 5 capable) Package 8-pin SO PowerPAD (DDA) surface-mount package Designed for good thermal performance in high-voltage applications Typical Applications Industrial power supplies (24 V / 48 V systems) Automotive power systems Telecom and networking equipment High cell-count battery systems Motor control and inverter subsystems #LM5013 #BuckConverter #DCDCConverter #TexasInstruments #PowerManagementIC #HighVoltageRegulator #3ARegulator #IndustrialPower #AutomotiveElectronics #SwitchingRegulator #COTController

Non-Synchronous Buck DC-DC Converter – 3 A non-synchronous step-down (buck) switching regulator with an integrated 80 V, 3.5 A power MOSFET for industrial, telecom, and high-voltage power supply applications. Operates from a 12 V to 76 V input voltage, provides an adjustable output voltage from 1.0 V to 76 V, and features a programmable switching frequency from 50 kHz to 750 kHz. Includes current-mode control, soft-start, enable input, 0 µA standby current, precision reference (±1.5%), externally programmable undervoltage lockout (UVLO) with hysteresis, overcurrent protection (OCP), overvoltage protection (OVP), and thermal shutdown (TSD). Specified for operation over a −40°C to +85°C temperature range and housed in an 8-pin HTSOP-J exposed-pad package. #ROHM #BD9G341AEFJE2 #BD9G341AEFJ #BuckConverter #DCDCConverter #StepDownRegulator #SwitchingRegulator #PowerManagement #3A #80VMOSFET #IndustrialPower #HTSOPJ8 #EmbeddedSystems

Single-channel high-side N-channel smart power switch for power distribution, supporting a 6 V to 18 V load voltage and up to 11 A continuous output current. Features 8.8 mΩ typical ON resistance, non-inverting ON/OFF control, and integrated overcurrent, overvoltage, short-circuit, and undervoltage lockout (UVLO) protection. Specified for operation over a −40°C to +150°C junction temperature range and housed in a PG-TSDSO-14-22 (14-pin TSSOP exposed pad) package. #Infineon #BTS70081EPPXUMA1 #SmartPowerSwitch #HighSideSwitch #LoadSwitch #PowerDistribution #PROFET #NChannel #11A #PowerManagement #AutomotiveElectronics #TSDSO14

Automotive Smart High-Side Power Switch – Single-channel N-channel smart high-side power switch for automotive power distribution and wire harness protection. Operates from a 4.1 V to 28 V supply (2.75 V minimum during cranking), supports a 15.7 A nominal load current, and features an ultra-low 3.6 mΩ typical RDS(on). Includes adjustable overcurrent protection (24 A to 137.5 A), integrated I²t wire protection, analog current sensing, open-load detection (ON/OFF state), short-circuit protection, reverse battery protection, overvoltage protection, undervoltage lockout (UVLO), overtemperature protection, slew-rate control, and logic-level control input. Qualified to AEC-Q100 and ISO 26262-compliant, it operates over a −40°C to +150°C junction temperature range and is housed in a 14-pin PG-TSDSO exposed-pad package. #Infineon #BTG7003A1EPWXUMA1 #PROFET #HighSideSwitch #SmartPowerSwitch #Automotive #PowerDistribution #LoadDriver #CurrentSense #WireProtection #AECQ100 #ISO26262 #EmbeddedSystems

Automotive H-Bridge DC Motor Driver IC – Fully integrated 40 V H-bridge motor driver with integrated power MOSFETs for brushed DC motors and one winding of a bipolar stepper motor. Operates from a 4 V to 40 V supply, delivers up to 5 A continuous output current, and features a PWM control interface with integrated current-sense output for motor monitoring. Includes an internal charge pump for high-side gate drive, low-RDS(on) MOSFETs, current regulation, undervoltage lockout (UVLO), overcurrent protection (OCP), thermal shutdown, and shoot-through protection. Qualified to AEC-Q100 Grade 1, operates over a −40°C to +125°C junction temperature range, and is housed in an 18-pin QFN (3 × 4 mm) wettable-flank package. #MonolithicPowerSystems #MPS #MPQ6612AGLEAEC1P #MPQ6612A #MotorDriver #HBridge #BrushedDCMotor #StepperMotor #CurrentSense #PWM #PowerMOSFET #AECQ100 #Automotive #EmbeddedSystems

Buck-Boost Switching Regulator IC Positive Adjustable (Fixed) 6.5V (11.5V) 1 Output 6A 22-PowerWFQFN The MAX25239/MAX25240 are small, synchronous, buck-boost converters with integrated H-bridge switches. These ICs provide a fixed-output regulation voltage and an externally adjustable output voltage in the 3V to 20V range with an input voltage above, below, or equal to the output regulation voltage. The ICs have typical 8.2A and 10A input current limit options and can support continuous load currents up to 6A depending on the input-to-output voltage ratio and operating frequency. It also has a wide input voltage range of 2V to 36V. The MAX25239/MAX25240 have three switching frequency options: 2.1MHz, 400kHz, and 200kHz. The 2.1MHz high switching frequency allows small external components and reduced output ripple, and guarantees no AM band interference, while the 400kHz or 200kHz switching frequency offers better efficiency and relieves the power consumption concern. The SYNC input allows three operation modes: skip mode with ultra-low quiescent current, forced fixed-frequency PWM operation, and synchronization to an external clock. The IC also includes spread-spectrum frequency modulation to minimize EMI interference. The MAX25239/MAX25240 feature a power-OK (POK) indicator, undervoltage lockout, overvoltage protection, cycle-by-cycle current limit, and thermal shutdown. The ICs are available in small, 4.25mm x 4.25mm x 0.75mm, 22-pin FC2QFN and 5.00mm x 5.00mm x 0.75mm, 18- pin FCQFN packages. Key Features Wide 2 V to 36 V input voltage range Synchronous buck-boost topology for seamless step-up and step-down conversion Delivers up to 6 A continuous output current Adjustable output voltage from 3 V to 20 V (device variant includes fixed output configuration options) High conversion efficiency with integrated low-RDS(ON) MOSFETs 400 kHz switching frequency with spread-spectrum option for reduced EMI Very low 95 µA quiescent current in standby and 10 µA shutdown current Integrated protection features including overvoltage, short-circuit, thermal shutdown, and undervoltage lockout (UVLO) Power-Good (PGOOD) output for power monitoring AEC-Q100 qualified for automotive applications Operating junction temperature range: −40°C to +150°C Compact 22-pin FC2QFN (4.25 × 4.25 mm) package #MAX25240AFFFVY #AnalogDevices #BuckBoostConverter #DCDCConverter #PowerManagement #AutomotiveElectronics #AECQ100 #SwitchingRegulator #EmbeddedSystems #AutomotivePower