Welcome to your new project. Imagine what you can build here.

Accelerometer X, Y, Z Axis ±2g, 4g, 8g, 16g 0.05Hz ~ 1.6kHz 14-LGA (3x5) The ADXL345 is a small, thin, ultralow power, 3-axis accelerometer with high resolution (13-bit) measurement at up to ±16 g. Digital output data is formatted as 16-bit twos complement and is accessible through either a SPI (3- or 4-wire) or I2C digital interface. The ADXL345 is well suited for mobile device applications. It measures the static acceleration of gravity in tilt-sensing applications, as well as dynamic acceleration resulting from motion or shock. Its high resolution (3.9 mg/LSB) enables measurement of inclination changes less than 1.0°. Several special sensing functions are provided. Activity and inactivity sensing detect the presence or lack of motion by comparing the acceleration on any axis with user-set thresholds. Tap sensing detects single and double taps in any direction. Free-fall sensing detects if the device is falling. These functions can be mapped individually to either of two interrupt output pins. An integrated memory management system with a 32-level first in, first out (FIFO) buffer can be used to store data to minimize host processor activity and lower overall system power consumption. Low power modes enable intelligent motion-based power management with threshold sensing and active acceleration measurement at extremely low power dissipation. The ADXL345 is supplied in a small, thin, 3 mm × 5 mm × 1 mm, 14-lead, plastic package. ► Ultralow power: as low as 23 µA in measurement mode and 0.1 µA in standby mode at VS = 2.5 V (typical) ► Power consumption scales automatically with bandwidth ► User-selectable resolution ► Fixed 10-bit resolution ► Full resolution, where resolution increases with g range, up to 13-bit resolution at ±16 g (maintaining 4 mg/LSB scale factor in all g ranges) ► Embedded memory management system with FIFO technology minimizes host processor load ► Single tap/double tap detection ► Activity/inactivity monitoring ► Free-fall detection ► Supply voltage range: 2.0 V to 3.6 V ► I/O voltage range: 1.7 V to VS ► SPI (3- and 4-wire) and I2C digital interfaces ► Flexible interrupt modes mappable to either interrupt pin ► Measurement ranges selectable via serial command ► Bandwidth selectable via serial command ► Wide temperature range (−40°C to +85°C) ► 10,000 g shock survival ► Pb free/RoHS compliant #commonpartslibrary #sensor #transducer #accelerometer

ADXL345 iMEMS® Accelerometer, 3 Axis Sensor Evaluation Board The ADXL345 measures acceleration in three axes (X, Y, Z) and outputs digital data via either I²C or SPI interfaces. It is widely used in applications like tilt sensing, vibration monitoring, free-fall detection, and motion-based user interfaces. Its high resolution (up to 13-bit) allows it to detect very small changes in motion, making it suitable for both consumer electronics and industrial applications. Key Features 3-axis acceleration measurement (X, Y, Z) Selectable measurement ranges: ±2g, ±4g, ±8g, ±16g High resolution (13-bit) with up to 4 mg/LSB sensitivity Digital output interfaces: I²C and SPI Low power consumption: ideal for battery-powered devices Built-in motion detection functions: Tap and double-tap detection Free-fall detection Activity and inactivity monitoring Wide bandwidth range: supports various data rates for different applications Operating voltage: typically 2.0V to 3.6V Compact package: small LGA form factor suitable for space-constrained designs Common Applications Smartphones and tablets (screen rotation, motion sensing) Wearable devices and fitness trackers Gaming controllers Robotics and drones Vibration and shock monitoring systems #commonpartslibrary #developmentboard #evaluationboard #sensor

Accelerometer, Gyroscope, Magnetometer, 9 Axis Sensor I2C, SPI, UART Output The BNO085 is a high-performance 9-axis absolute orientation sensor system-in-package (SiP) that integrates a 3-axis accelerometer, 3-axis gyroscope, 3-axis magnetometer, and a low-power ARM Cortex-M0+ microcontroller running CEVA/Hillcrest SH-2 sensor fusion firmware. It provides accurate real-time orientation, motion tracking, and activity detection while offloading complex sensor fusion calculations from the host processor. The device is widely used in robotics, AR/VR systems, wearables, drones, IoT devices, and navigation applications. Key Features 9-axis motion sensing with integrated accelerometer, gyroscope, and magnetometer Built-in SH-2 sensor fusion engine for accurate orientation tracking ARM Cortex-M0+ processor for onboard motion processing Outputs quaternion, rotation vector, linear acceleration, gravity vector, angular velocity, and magnetic field data Advanced motion detection including tap, step, shake, and significant motion detection Activity classification and stability detection capabilities Low-latency rotation vectors optimized for AR/VR applications Supports I²C, SPI, and UART communication interfaces Configurable output data rates and timestamps Low-power operation suitable for battery-powered devices Compact 28-pin LGA package (5.2 mm × 3.8 mm) Operating temperature range: -40°C to +85°C Backward compatible with BNO080 designs while adding support for future application-specific libraries Applications Robotics and autonomous systems Virtual Reality (VR) and Augmented Reality (AR) Wearable devices and fitness trackers Drones and UAVs Head-mounted displays (HMDs) Industrial motion tracking IoT and smart devices Navigation and positioning systems #BNO085 #IMU #9AxisSensor #MotionTracking #SensorFusion #OrientationSensor #Robotics #AR #VR #IoT #Wearables #EmbeddedSystems #CEVA #HillcrestLabs #MotionDetection #Quaternion #InertialMeasurementUnit

Delay Line IC Programmable 1024 Tap 3.2ns ~ 14.8ns 32-TQFP #commonpartslibrary #integratedcircuit #delayline #programmable

WP-BUFU REDCUBE Bush, full height: 7mm, total height: 10.5mm, thread length: 4mm, pin length: 3.5mm, raster: 2.54mm, REDCUBE Press-Fit; M5, blind 4mm 16 Pin Screw Terminal, Power Tap M5 Through Hole The 7461147 is a high-current PCB-mounted power terminal from the REDCUBE® WP-BUFU series by Würth Elektronik. It is designed to provide a robust and low-resistance connection for transferring high currents between cables, busbars, and printed circuit boards. The terminal utilizes press-fit technology, eliminating the need for soldering while ensuring a gas-tight, vibration-resistant electrical connection. It is particularly suitable for power distribution, industrial equipment, automotive electronics, battery systems, and renewable energy applications. Key Features High current rating up to 180 A M5 screw terminal for secure high-power connections Press-fit termination for solderless PCB assembly 16-pin through-hole mounting configuration Gas-tight electrical connection for long-term reliability Excellent resistance to vibration and mechanical shock Low contact resistance for efficient power transfer Simplifies manufacturing by eliminating soldering processes Suitable for high-current power distribution and battery applications RoHS compliant design Typical Applications Power supplies and power converters Battery management and energy storage systems DC-DC and DC-AC converters Industrial automation equipment Automotive power electronics Solar and wind energy systems High-current PCB power distribution networks #CommonPartsLibrary #REDCUBE #PowerTerminal #PressFit #HighCurrentConnector #PCBTerminal #WurthElektronik #IndustrialElectronics #AutomotiveElectronics #PowerDistribution #EnergyStorage #RenewableEnergy #7461147

Accelerometer X, Y, Z Axis ±2g, 4g, 8g, 16g 0.05Hz ~ 1.6kHz 14-LGA (3x5) The ADXL345 is a small, thin, ultralow power, 3-axis accelerometer with high resolution (13-bit) measurement at up to ±16 g. Digital output data is formatted as 16-bit twos complement and is accessible through either a SPI (3- or 4-wire) or I2C digital interface. The ADXL345 is well suited for mobile device applications. It measures the static acceleration of gravity in tilt-sensing applications, as well as dynamic acceleration resulting from motion or shock. Its high resolution (3.9 mg/LSB) enables measurement of inclination changes less than 1.0°. Several special sensing functions are provided. Activity and inactivity sensing detect the presence or lack of motion by comparing the acceleration on any axis with user-set thresholds. Tap sensing detects single and double taps in any direction. Free-fall sensing detects if the device is falling. These functions can be mapped individually to either of two interrupt output pins. An integrated memory management system with a 32-level first in, first out (FIFO) buffer can be used to store data to minimize host processor activity and lower overall system power consumption. Low power modes enable intelligent motion-based power management with threshold sensing and active acceleration measurement at extremely low power dissipation. The ADXL345 is supplied in a small, thin, 3 mm × 5 mm × 1 mm, 14-lead, plastic package. ► Ultralow power: as low as 23 µA in measurement mode and 0.1 µA in standby mode at VS = 2.5 V (typical) ► Power consumption scales automatically with bandwidth ► User-selectable resolution ► Fixed 10-bit resolution ► Full resolution, where resolution increases with g range, up to 13-bit resolution at ±16 g (maintaining 4 mg/LSB scale factor in all g ranges) ► Embedded memory management system with FIFO technology minimizes host processor load ► Single tap/double tap detection ► Activity/inactivity monitoring ► Free-fall detection ► Supply voltage range: 2.0 V to 3.6 V ► I/O voltage range: 1.7 V to VS ► SPI (3- and 4-wire) and I2C digital interfaces ► Flexible interrupt modes mappable to either interrupt pin ► Measurement ranges selectable via serial command ► Bandwidth selectable via serial command ► Wide temperature range (−40°C to +85°C) ► 10,000 g shock survival ► Pb free/RoHS compliant #CommonPartsLibrary #IntegratedCircuit #Sensor #Transducer #Motion-Sensor #Accelerometer #ADXL345

Accelerometer, Gyroscope, 6 Axis Sensor I2C, I3C, SPI Output The BMI323 is a low-power, high-performance inertial measurement unit developed by Bosch Sensortec. It integrates a three-axis accelerometer and a three-axis gyroscope within a compact surface-mount package intended for motion sensing applications requiring precise movement detection, orientation tracking, vibration monitoring, and activity recognition. The device is optimized for wearable electronics, industrial sensing, robotics, navigation systems, IoT devices, and consumer electronics where low power consumption and high motion accuracy are critical. The sensor includes advanced digital signal processing, configurable motion-detection features, programmable interrupts, and integrated FIFO buffering to reduce host processor workload and improve system efficiency. Communication is supported through standard digital interfaces, enabling straightforward integration with microcontrollers and embedded platforms. The BMI323 is designed for robust environmental performance and supports flexible power management modes suitable for battery-operated systems. Engineering Specifications Device Type Six-axis inertial measurement unit consisting of: Three-axis accelerometer Three-axis gyroscope Manufacturer Bosch Sensortec Package Compact LGA surface-mount package suitable for automated assembly processes. Accelerometer Characteristics Supports multiple selectable full-scale measurement ranges for motion and acceleration sensing applications. Provides high-resolution digital output with configurable filtering and sampling parameters for low-noise operation and accurate motion analysis. Gyroscope Characteristics Integrated three-axis angular rate sensor with programmable measurement ranges and digital filtering capabilities. Designed for rotational movement tracking, stabilization, gesture recognition, and inertial navigation applications. Digital Interfaces Supports: I²C serial communication SPI serial communication I3C compatible operation Power Features Designed for ultra-low power operation with multiple configurable power modes to optimize energy consumption for portable and battery-powered devices. Embedded Features Includes integrated: FIFO data buffering Motion detection engine Activity and inactivity detection Tap and gesture detection Orientation and tilt sensing Interrupt generation Self-test functionality Output Data Handling Provides configurable output data rates, oversampling settings, and digital filtering options for balancing performance, bandwidth, and power consumption. Temperature Performance Integrated temperature sensing and compensation support for improved measurement stability across varying environmental conditions. Interrupt System Programmable interrupt outputs support event-driven system architectures and allow efficient host wake-up functionality. Operating Environment Designed for operation across industrial and consumer temperature ranges with stable sensor performance under dynamic motion conditions. Applications Suitable for: Wearable devices Smart watches Fitness trackers Industrial motion monitoring Robotics Drones Navigation systems Gaming controllers AR/VR systems IoT motion sensing Human-machine interfaces #commonpartslibrary #integratedcircuit #accelerometer #sensor

Delay Line IC Programmable 8 Tap 1µs ~ 33.6s 6-WFDFN Exposed Pad #Timer #commonpartslibrary

Delay Line IC Programmable 8 Tap 1µs ~ 33.6s 6-WFDFN Exposed Pad #Timer #commonpartslibrary

WE-LAN 10/100/1000 Base-T SMT Transformer 1 Port 1000BASE-T LAN transformer, SMD, 24pin, pitch 1.27mm, 0C to +70C, 1.5KVrms isolation, PoE+ 1100mA per centre tap

Delay Line IC Programmable 8 Tap 1µs ~ 33.6s SOT-23-6 Thin, TSOT-23-6 #Timer #commonpartslibrary

Accelerometer X, Y, Z Axis ±2g, 4g, 8g, 16g 0.05Hz ~ 1.6kHz 14-LGA (3x5) The ADXL345-EP is an extended performance version of the ADXL345, which is a small, thin, ultralow power, 3-axis accelerometer with high resolution (13-bit) measurement at up to ±16 g. Digital output data is formatted as 16-bit twos complement and is accessible through either a SPI (3- or 4-wire) or I2 C digital interface. The ADXL345-EP is well suited for extended temperature range industrial and aerospace equipment. It measures the static acceleration of gravity in tilt-sensing applications, as well as dynamic acceleration resulting from motion or shock. Its high resolution (3.9 mg/LSB) enables measurement of inclination changes less than 1.0°. Several special sensing functions are provided. Activity and inactivity sensing detect the presence or lack of motion by comparing the acceleration on any axis with user-set thresholds. Tap sensing detects single and double taps in any direction. Freefall sensing detects if the device is falling. These functions can be mapped individually to either of two interrupt output pins. An integrated memory management system with a 32-level first in, first out (FIFO) buffer can be used to store data to minimize host processor activity and lower overall system power consumption. Low power modes enable intelligent motion-based power management with threshold sensing and active acceleration measurement at extremely low power dissipation. The ADXL345-EP is supplied in a small, thin, 3 mm × 5 mm × 1 mm, 14-lead, enhanced plastic package. Ultralow power: as low as 23 µA in measurement mode and 0.1 µA in standby mode at VS = 2.5 V (typical) Power consumption scales automatically with bandwidth User-selectable resolution from 10 to 13 bits 4 mg/LSB scale factor in all g ranges 32-sample FIFO minimizes host processor load Single tap, double tap, and free-fall detection Activity/inactivity monitoring Supply voltage range: 2.0 V to 3.6 V I/O voltage range: 1.7 V to VS SPI (3- and 4-wire) and I2C digital interfaces Flexible interrupt modes mappable to either interrupt pin Measurement ranges selectable via serial command Bandwidth selectable via serial command 10,000 g shock survival Pb free/RoHS compliant Small and thin: 3 mm × 5 mm × 1 mm LGA package #CommonPartsLibrary #Sensor #Motion-sensor #accelerometer