Buck Switching Regulator IC Positive Adjustable 1.2V 1 Output 3.5A 8-PowerSOIC (0.154", 3.90mm Width) The LM5013DDAR is a 100-V input, 3.5-A buck switching regulator IC that efficiently steps down high DC voltages (such as 24 V, 48 V, or battery rails) to lower regulated outputs. It is optimized for rugged environments where wide input variations and high reliability are required. It features ultra-low quiescent current operation, making it suitable for systems that require high efficiency even at light load or standby conditions. Key Features Wide input voltage range: 6 V to 100 V Up to 3.5 A output current capability Integrated 100-V high-side MOSFET Non-synchronous buck topology Ultra-low quiescent current (IQ) for high efficiency in standby Constant-on-time (COT) control for fast transient response No external compensation components required Adjustable output voltage (down to ~1.2 V reference) 50 ns minimum on/off time for high step-down ratios Built-in protection features: Overcurrent protection Thermal shutdown Input undervoltage lockout (UVLO) Open-drain power-good (PGOOD) signal for system monitoring Meets low EMI requirements (CISPR 25 Class 5 capable) Package 8-pin SO PowerPAD (DDA) surface-mount package Designed for good thermal performance in high-voltage applications Typical Applications Industrial power supplies (24 V / 48 V systems) Automotive power systems Telecom and networking equipment High cell-count battery systems Motor control and inverter subsystems #LM5013 #BuckConverter #DCDCConverter #TexasInstruments #PowerManagementIC #HighVoltageRegulator #3ARegulator #IndustrialPower #AutomotiveElectronics #SwitchingRegulator #COTController

LED Driver IC 16 Output Linear PWM Dimming 25mA 5.5V 28-TSSOP PCA9685PW,118 is a 16-channel, 12-bit PWM LED controller with an I²C interface designed for LED dimming, RGB/RGBA lighting, and servo motor control applications. It provides independent PWM control for up to 16 outputs, allowing precise brightness or position control while minimizing MCU GPIO usage. The device supports Fast-mode Plus I²C communication up to 1 MHz and operates from a 2.3 V to 5.5 V supply range. It is commonly used in robotics, LED backlighting, automation systems, and PWM expansion modules for microcontrollers such as Arduino, ESP32, and Raspberry Pi. Key Features 16 independent PWM output channels 12-bit PWM resolution (4096 steps) Programmable PWM frequency from approximately 24 Hz to 1526 Hz I²C Fast-mode Plus compatible interface up to 1 MHz Six hardware address pins allowing up to 62 devices on one I²C bus Programmable open-drain or totem-pole outputs Output capability: 25 mA sink current 10 mA source current Internal 25 MHz oscillator with optional external clock input Individual programmable LED ON/OFF timing for reduced EMI and current surges Supports software reset and group addressing (All Call/Sub Call) 5.5 V tolerant inputs and outputs Operating voltage range: 2.3 V to 5.5 V Package: 28-pin TSSOP (PW suffix) #CommonPartsLibrary #IntegratedCircuit #PowerManagement #LEDdriver

Comparator General Purpose Open-Drain, Rail-to-Rail SOT-23-5 #CommonPartsLibrary #Integratedcircuit #Linearcomparator

MCP6566 Series 5.5 V 1 pA Low Power Open-Drain Output Comparator - SOT-23-5 #CommonPartsLibrary #Integratedcircuit #Linearcomparator

Supervisor Open Drain or Open Collector 1 Channel SOT-23-3 The MCP120T-450I/TT is a microcontroller supervisory (voltage reset) IC from Microchip Technology designed to monitor the system supply voltage and ensure reliable startup and operation of microcontroller-based systems. It keeps the microcontroller in the reset state until the supply voltage reaches a safe operating level and automatically asserts a reset signal if the supply voltage falls below the preset threshold, protecting the system from brown-out and power-failure conditions. The device features an open-drain active-low RESET output, a 4.375 V threshold, and is housed in a compact SOT-23-3 package, making it suitable for space-constrained embedded applications. Key Features Monitors a single supply voltage with a 4.375 V reset threshold Open-drain, active-low RESET output Holds the microcontroller in reset during power-up until VDD is stable Automatically resets the system during brown-out or power-loss events 150 ms minimum reset timeout after VDD exceeds the threshold Supports 3 V, 3.3 V, and 5 V system supervision Low operating current (typically 45 µA) Wide operating temperature range: −40°C to +85°C Compact SOT-23-3 surface-mount package Hashtags #Microchip #MCP120 #VoltageSupervisor #ResetIC #BrownOutProtection #PowerOnReset #PMIC #EmbeddedSystems #Microcontroller #SOT23 #PowerManagement #CircuitProtection

Comparator General Purpose CMOS, Open-Drain 8-SOIC #CommonPartsLibrary #Integratedcircuit #Linearcomparator

LED Driver IC 1 Output DC DC Controller SEPIC, Step-Down (Buck), Step-Up (Boost) Analog, PWM Dimming 8-SO-EP # AL8866QSP-13 Engineering Specifications **General Description** The AL8866QSP-13 is an automotive-qualified, multi-topology DC-switching LED controller manufactured by Diodes Incorporated. It is designed to control an external power MOSFET for high-power automotive LED lighting systems. The device supports buck, boost, buck-boost and single-ended primary-inductance converter configurations. Its wide input-voltage range makes it suitable for automotive power systems and various high-voltage LED applications. The controller uses fixed-frequency peak current-mode regulation with spread-spectrum frequency modulation to reduce electromagnetic interference. It supports both analog and pulse-width-modulation dimming through the DIM input. An integrated programmable soft-start function gradually increases the inductor and switching currents during startup to reduce output-voltage and current stress. The open-drain fault output provides system-level fault reporting for abnormal operating conditions. **Engineering Specifications** **Manufacturer:** Diodes Incorporated **Manufacturer Part Number:** AL8866QSP-13 **Component Type:** Automotive LED driver controller **Converter Topologies:** Buck, boost, buck-boost and SEPIC **Control Architecture:** Fixed-frequency peak current-mode control **External Switching Device:** External power MOSFET **Minimum Input Voltage:** Four point seven volts **Maximum Input Voltage:** Eighty-five volts **Maximum Output Voltage:** Eighty-five volts **Switching Frequency:** Four hundred kilohertz **Frequency Modulation:** Spread-spectrum modulation for reduced electromagnetic interference **LED Current Control:** External current-sense resistor and external MOSFET configuration **Feedback Voltage:** Two hundred millivolts **Typical Quiescent Current:** One point eight milliamperes **Typical Efficiency:** Up to approximately ninety-three percent, depending on the application circuit and external components **Dimming Methods:** Analog dimming and pulse-width-modulation dimming **Analog Dimming Range:** One percent to one hundred percent **Analog Dimming Dynamic Range:** Greater than one hundred to one **Pulse-Width-Modulation Dimming Ratio:** One hundred to one at a two-hundred-hertz dimming frequency **Pulse-Width-Modulation Frequency Range:** Approximately one hundred hertz to one kilohertz **Full-Brightness Current Accuracy:** Approximately plus or minus three percent **Low-Level Dimming Current Accuracy:** Approximately plus or minus twelve percent at twenty-percent dimming **Soft-Start Function:** Externally programmable **Fault Output:** Active-low open-drain fault indicator **Protection Features:** Output overvoltage protection, LED open-circuit protection, output undervoltage protection, LED short-circuit protection, cycle-by-cycle overcurrent limitation, current-sense resistor short-circuit protection, inductor and diode short-circuit detection, diode open-circuit protection and thermal shutdown **Automotive Qualification:** AEC-Q100 Grade One qualified **Automotive Documentation:** PPAP capable **Manufacturing Standard:** Manufactured in IATF-certified automotive facilities **Operating Temperature Range:** Minus forty degrees Celsius to positive one hundred twenty-five degrees Celsius **Package Type:** Thermally enhanced SO-8 exposed-pad package **Pin Count:** Eight leads with exposed thermal ground pad **Mounting Style:** Surface mount **Packing Method:** Thirteen-inch tape and reel **Standard Packing Quantity:** Two thousand five hundred components per reel **Moisture Sensitivity:** Level One **Terminal Finish:** Matte-tin-plated leads **Environmental Compliance:** Lead-free, RoHS compliant, halogen-free and antimony-free **Typical Applications** Automotive high-beam and low-beam lighting Automotive daytime running lights Automotive fog lights Automotive turn-signal lights Automotive position lights Automotive brake and stop lights High-power exterior LED lighting Multi-topology automotive LED driver modules #AL8866QSP13 #AL8866Q #DiodesIncorporated #LEDDriver #AutomotiveLED #AutomotiveElectronics #BuckConverter #BoostConverter #BuckBoostConverter #SEPICConverter #PowerElectronics #LEDLighting #ElectronicComponents #EngineeringSpecifications

I2C Port Expander with 8 Push-Pull and 8 Open-Drain I/Os, QSOP-24 Expander I2C Parallel Port GPIO Maxim QSOP*3.9x8.7*P0.635mm*

Comparator featuring two independent low-voltage comparators for comparing analog input signals and providing open-drain digital outputs. The LM393LV operates from a 1.65 V to 5.5 V supply, supports a –40°C to +125°C operating temperature range, includes rail-to-rail common-mode input capability, and offers a push-pull output option in other device variants, while the LM393LVPWR specifically provides open-drain outputs. #Comparator #DualComparator #OpenDrain #LowVoltage #Analog #TexasInstruments #LM393LV #SOIC #Electronics #PCB

Dual Non-Inverting Open-Drain Buffer IC – Dual non-inverting buffer with open-drain outputs for logic level translation, bus interfacing, signal buffering, wired-AND logic, and embedded digital systems. Operates from a 1.65 V to 5.5 V supply and features two independent 1-bit buffer channels capable of sinking up to 32 mA per output. The open-drain outputs allow direct interfacing with multiple voltage domains using external pull-up resistors, making the device suitable for I²C buses, interrupt lines, LED driving, and mixed-voltage logic applications. Features high-speed CMOS operation, low static power consumption, 5.5 V input tolerance, and is specified for operation over a −40°C to +85°C ambient temperature range. Housed in a 6-pin SC-88 (SC-70-6 / SOT-363) surface-mount package. #onsemi #NC7WZ07P6X #LogicBuffer #OpenDrain #NonInvertingBuffer #LogicIC #LevelShifter #I2C #SignalBuffer #WiredAND #SC88 #EmbeddedSystems

Power Switch/Driver 1:1 N-Channel 1.35A 28-WQFN (4x5) The TPS274160 device is a smart high-side switch with four integrated 160-mΩ NMOS power FETs and a chargepump to drive the gates. The device offers robust protection and diagnostic features to drive various loads (inductive, capacitive, and resistive) such as low wattage bulbs, LEDs, relays, solenoids, heaters, and sub-modules. The part enables flexible, multi-channel output configurations through paralleling channels and is in a very small WQFN package to enable usage in space constrained applications. The device is protected against short circuit events and over-temperature events, safely shutting off the output during fault events. The device also implements an external adjustable current limiting feature. This feature improves the reliability of the system by reducing inrush current when driving large capacitive loads and minimizing overload current thereby eliminating system supply brown out condition. The device also integrates diagnostic features like output current monitoring (version B) and open load detection to enable improved intelligence in modules and to enable predictive maintenance functionality. • Quad-channel 160-mΩ smart high-side switch • Wide DC operating voltage range: 5 V to 36 V – 50-V absolute maximum voltage • Accurate adjustable current limiting (250 mA to 4 A) • Intelligent diagnostic features – TPS274160A: Open-drain fault output – TPS274160B: Analog current sense – Open-load or short to supply detection in the off-state • Robust protection features – Short-circuit protection – Inductive load flyback clamp – Undervoltage lockout (UVLO) protection – Loss of GND protection • Excellent ESD protection on VS and OUT pins – ±8/±15 kV IEC 61000-4-2 ESD contact/air discharge • Available in small and 28-pin leadless QFN packages • Functional Safety-Capable – Documentation available to aid functional safety system design 2 Applications • Digital output modules • Standalone remote I/O • Motor drives • Solenoid or valve drive #TexasInstruments #TPS274160BRLHR #HighSideSwitch #SmartSwitch #IndustrialAutomation #PowerManagement #LoadDriver #CurrentLimiting #ProtectionIC #IndustrialControl #RemoteIO #SolenoidDriver #MotorDrive #EmbeddedSystems #ElectronicsDesign

Monitors & Reset Circuits TPS3808G33DRVT WSON-6_L2.0-W2.0-P0.65-TL-EP LCSC Part Number: C702176 JLCPCB Part Class: undefined Manufactured by TI(德州仪器) Texas Instruments TPS3808 low-quiescent-current voltage supervisor and reset generator, supply voltage monitoring from 0.4V to 5V, 0.5% threshold accuracy, adjustable reset delay from 1.25ms to 10s using external capacitor, open-drain RESET output, manual reset (MR) input, ultra-low 2.4µA typical quiescent current, suitable for microcontrollers, DSPs, FPGAs, ASICs, battery-powered and portable devices, operating temperature range -40°C to +125°C, available in SOT-23-6 and WSON-6 packages. Search Keywords: TPS3808, TPS3808G, Texas Instruments TPS3808, TI TPS3808, voltage supervisor, reset supervisor, reset generator, watchdog reset, power-on reset, POR supervisor, brownout detector, voltage monitor IC, microcontroller supervisor, open drain reset, adjustable reset delay, manual reset supervisor, low power supervisor, battery powered reset IC, TPS3808 datasheet, TPS3808 SOT-23-6, TPS3808 WSON-6 Hashtags: #TPS3808 #TexasInstrumentsTPS3808 #TIVoltageSupervisor #VoltageSupervisor #ResetSupervisor #ResetGenerator #PowerOnReset #BrownoutDetector #VoltageMonitorIC #MicrocontrollerSupervisor #OpenDrainReset #ManualReset #LowPowerSupervisor #BatteryPoweredDesign #SOT236 #WSON6

Single 1.8V Low-Power Open-Drain Output Comparator, SOT-23-5 cmp collector SOT?23*