The RP2350, developed by Raspberry Pi Ltd, is a high-performance microcontroller designed to cater to a broad range of applications requiring efficient power management, advanced security features, and versatile IO options. This microcontroller stands out with its dual-core architecture, featuring either Cortex-M33 or Hazard3 processors operating at up to 150 MHz, ensuring robust performance for complex applications. It boasts a substantial 520 KB of on-chip SRAM distributed across 10 independent banks, enhancing parallel data processing capabilities. Additionally, the RP2350 supports up to 16 MB of external QSPI flash/PSRAM for extensive program and data storage, further expandable via an optional second chip-select. A notable feature of the RP2350 is its integrated on-chip switched-mode power supply, designed to generate core voltage efficiently, complemented by a low-quiescent-current LDO mode for reduced power consumption in sleep states. Security is a paramount feature of the RP2350, offering options for boot signing with key fingerprint in OTP, hardware mitigations against fault injection attacks, and a hardware SHA-256 accelerator for cryptographic operations. The microcontroller is also equipped with a comprehensive set of peripherals, including USB 1.1 controller and PHY, multiple UARTs, SPI, and I2C controllers, 24 PWM channels, and 12 programmable IO (PIO) state machines, providing extensive interface capabilities. The RP2350 is available in QFN-60 and QFN-80 packages, with or without flash-in-package options, catering to various design requirements and application needs.

10/100 Base-T/TX PHY Ethernet controller that supports PoE with SPI Interface. Based on W5500. Can be used as PoE injector. #project #referenceDesign #template #w5500 #PoE #EtherNet #RJ5

10/100 Base-T/TX PHY Ethernet controller that supports PoE with SPI Interface. Based on W5500. Can be used as PoE injector. #project #referenceDesign #template #w5500 #PoE #EtherNet #RJ5

This is a LoRa soil monitor Reference Design. It uses a STM32L031G6U6S microcontroller and a RFM95W-915S2 LoRa transceiver, integrated with sensor interfacing and LED indicators. Communication occurs via USART and SPI. The system is powered using a battery. #referenceDesign #simple-embedded #stm #template #reference-design

3D Camera Module is a scalable SPI enabled 4 camera array pinout for 3D photogrammetry reconstruction which uses I2C to connect between each module to expand camera capacity while keeping capture sequences in sync. It uses ATMega32U4 with its built in USB 2.0 for data transfer and camera array adjustments and capture as well as a micro SD card slot for local image storage. An interrupt logic pinout should be used on the SPI master module as capture command. Each module is powered via USB-C (5V) or barrel jack (12V regulated to 5V).

Haptic Glove Controller Board NUCLEO-F411RE based Fixed Servo Connections to match standard servo wiring Revised footprint of 2n3904s transistors since base and emitter footprint were swapped Larger power traces Swapped SDO and SDI of SPI Lines to the FPC connector so it matches with peripheral.

The LIS3DH is a very popular low power triple-axis accelerometer. It's low-cost, but has just about every 'extra' you'd want in an accelerometer. This sensor communicates over I2C or SPI (our library code supports both) so you can share it with a bunch of other sensors on the same I2C bus. There's an address selection pin so you can have two accelerometers share an I2C bus.

Time-to-Digital converter plug-on module (shield) for Raspberry Pi B+. The board utilizes a TDC7200 (TI) with a time resolution of ~50ps. The Start/Stop inputs to the TDC can be configured with JP2 from either external signals or coming from the RPi's GPIO5 pin in case a timing signal is present at this pin from another plug-on board on the same RPi. Start and Stop signals can be configured from different signals (coming from the input connectors) or the same source (setting "common" on JP3) either supplied from the Start input connector or GPIO5. Read-out of the TDC chip is done through the RPi's SPI bus.

Haptic Glove Controller Board NUCLEO-F411RE based Fixed Servo Connections to match standard servo wiring Revised footprint of 2n3904s transistors since base and emitter footprint were swapped Larger power traces Swapped SDO and SDI of SPI Lines to the FPC connector so it matches with peripheral.

RP2040 is a low-cost, high-performance microcontroller device with flexible digital interfaces. Key features: • Dual Cortex M0+ processor cores, up to 133 MHz • 264 kB of embedded SRAM in 6 banks • 30 multifunction GPIO • 6 dedicated IO for SPI Flash (supporting XIP) • Dedicated hardware for commonly used peripherals • Programmable IO for extended peripheral support • 4 channel ADC with internal temperature sensor, 0.5 MSa/s, 12-bit conversion • USB 1.1 Host/Device

10/100 Base-T/TX PHY Ethernet controller that supports PoE with SPI Interface. Based on W5500. Can be used as PoE injector. #project #referenceDesign #template #w5500 #PoE #EtherNet #RJ5

3D Camera Module is a scalable SPI enabled 4 camera array pinout for 3D photogrammetry reconstruction which uses I2C to connect between each module to expand camera capacity while keeping capture sequences in sync. It uses ATMega32U4 with its built in USB 2.0 for data transfer and camera array adjustments and capture as well as a micro SD card slot for local image storage. An interrupt logic pinout should be used on the SPI master module as capture command. Each module is powered via USB-C (5V) or barrel jack (12V regulated to 5V).

10/100 Base-T/TX PHY Ethernet controller that supports PoE with SPI Interface. Based on W5500. Can be used as PoE injector. #project #referenceDesign #template #w5500 #PoE #EtherNet #RJ5

This is a LoRa remote control project built around a Raspberry Pi RP2040 SoC and the RFM95W LoRa module. The design includes user interface features such as multiple buttons and LEDs, power management components, and a temperature sensor. The project utilizes SPI, I2C, and USB interfaces for communication and control. #referenceDesign #simple-embedded #raspberrypi #lora #template #reference-design

10/100 Base-T/TX PHY Ethernet controller that supports PoE with SPI Interface. Based on W5500. Can be used as PoE injector. #project #referenceDesign #template #w5500 #PoE #EtherNet #RJ5

The LIS3DH is a very popular low power triple-axis accelerometer. It's low-cost, but has just about every 'extra' you'd want in an accelerometer. This sensor communicates over I2C or SPI (our library code supports both) so you can share it with a bunch of other sensors on the same I2C bus. There's an address selection pin so you can have two accelerometers share an I2C bus

Accelerometer, Gyroscope, Magnetometer, 9 Axis Sensor I²C, SPI Output

10/100 Base-T/TX PHY Ethernet controller that supports PoE with SPI Interface. Based on W5500. Can be used as PoE injector. #project #referenceDesign #template #w5500 #PoE #EtherNet #RJ5

Humidity Temperature Sensor 0 ~ 100% RH I²C, SPI ±3% with 4 pins

Portable ESP32-S3 AI voice assistant development board with USB-C programming, LiPo charging, OLED, I2S microphone/amplifier, SPI flash, and microSD expansion.

Portable AI-powered spectral reflectance analyzer based on a Radxa Zero 3W carrier PCB, with AS7341 spectral sensing, GPS, SPI touchscreen LCD, microSD logging, USB-C LiPo charging, and integrated optical LED measurement head.

DeskNeuron V0.1 — USB-C ESP32-S3 6-key macro pad with dual EC11 encoders and SPI TFT header.

Professional 4-layer STM32H743ZIT6 learning/development board with USB-C power, USB FS, SWD, crystals, SPI flash, ESP-12F Wi-Fi, full GPIO breakout, and expansion headers.

Carrier board schematic for network-audio-sink v1.0 using plug-in dev board modules via pin headers plus selected on-board ICs. Initial net plan includes 5V_BUS, 3V3, GND, I2S0/I2S1 audio, SPI control, and Ethernet differential-pair nets.

Four-channel electrochemical gas sensor signal-conditioning module based on the TI LMP91000EVM architecture, with shared I2C, per-channel SPI ADCs, 2.5V reference, sensor headers, and STM32F767ZI interface.