A board with a lora module (which can be programmed) and the ability to work autonomously from a battery and a solar panel #mppt #solar #lora #stm

LoRa Weather Station

Firefly Board is part of a smart network designed for wireless control of light, water and other parts of the house in locations where GSM communication and WiFi are not available. #LoRa #smart #IoT #power #led #arm #stm32

The "Green Dot 2040E5" Board is a Node that interfaces RS485 Sensor probes and can log information to the cloud using LoRa Connectivity. It uses the XIAO RP2040 and the LoRa-E5 (STM32WLE5JC) modules from Seeed Studio to do its magic. It also has amazing power management capabilities (Solar charging, Battery protection, etc) that make it very useful for IoT applications #SeeedStudio #XIAO #LoRa #RP2040 #IoT

A board with a lora module (which can be programmed) and the ability to work autonomously from a battery and a solar panel #mppt #solar #lora #stm

The "Green Dot 2040E5" Board is a Node that interfaces RS485 Sensor probes and can log information to the cloud using LoRa Connectivity. It uses the XIAO RP2040 and the LoRa-E5 (STM32WLE5JC) modules from Seeed Studio to do its magic. It also has amazing power management capabilities (Solar charging, Battery protection, etc) that make it very useful for IoT applications #Seeed #XIOA #LoRa #RP2040 #IoT

The "Green Dot 2040E5" Board is a Node that interfaces RS485 Sensor probes and can log information to the cloud using LoRa Connectivity. It uses the XIAO RP2040 and the LoRa-E5 (STM32WLE5JC) modules from Seeed Studio to do its magic. It also has amazing power management capabilities (Solar charging, Battery protection, etc) that make it very useful for IoT applications #Seeed #XIOA #LoRa #RP2040 #IoT

Firefly Board is part of a smart network designed for wireless control of light, water and other parts of the house in locations where GSM communication and WiFi are not available. #LoRa #smart #IoT #power #led #arm #stm32

Production-prototype ESP32-S3 control/RF/GNSS/sensor board for an outdoor livestock collar. Includes LoRa 915 MHz, GNSS, I2C/I2S sensors, local actuator drivers, battery-cell solder pads, solar pass-through, soldered flex-tail zones, HV electrode isolation, test points, and a 120 mm x 80 mm 4-layer FR4 target stackup.

Single M5Stack Cardputer ADV HAT integrating CC1101 sub-GHz radio, nRF24L01+ PA/LNA 2.4GHz radio, LoRa RA-02, and PN532 NFC with shared host interface, 3.3V power distribution, decoupling, and RF layout constraints.

4-layer marine GPS timing and communication device using nRF52840, u-blox ZED-F9P GNSS with external active antenna via u.FL, 915 MHz LoRa radio, Li-ion battery with USB-C charging, separate clean GNSS LDO and digital 3.3V rail, SPI memory LCD, RGB LEDs, buzzer, and 6-axis IMU. PCB target is a 70 mm circular layout with strict RF zoning, dedicated ground plane, 50 ohm RF traces, physical separation between GNSS and LoRa, and low-noise placement suitable for harsh marine environments.

SCADA Sensor Node v2.1 using a Heltec WiFi LoRa 32 V4 module with separate +5V and board-generated +3V3 rails, ADS131M08 8-channel ADC front end, TCA9548A I2C multiplexer, TMP102-based fan control, ULN2003A relay and fan driver, CT/pressure/analog/One-Wire/vibration/humidity/Qwiic/flow/digital sensor interfaces, relay outputs, fan connector, brownout sensing, and a 200 mm x 140 mm 2-layer layout with Heltec keepout, antenna clearance, mounting holes, and DIN-rail slots.

Village Node ESP32 DevKit and LoRa Carrier Board

The "Green Dot 2040E5" Board is a Node that interfaces RS485 Sensor probes and can log information to the cloud using LoRa Connectivity. It uses the XIAO RP2040 and the LoRa-E5 (STM32WLE5JC) modules from Seeed Studio to do its magic. It also has amazing power management capabilities (Solar charging, Battery protection, etc) that make it very useful for IoT applications #internetOfThings #smartHomeDevices #SeeedStudio #XIAO #LoRa #RP2040 #IoT

Architectural Lavender Translation Collar – ESP32‑S3 Wi‑Fi + LoRa, USB‑C, Li‑ion, low‑power design Overview Experience a cutting-edge IoT solution with this low‑power board built around the ESP32‑S3‑MINI‑1‑N8. Designed for seamless Wi‑Fi (2.4 GHz), BLE, and LoRa (868 MHz) connectivity, this board integrates ENS161 and ENS210 sensors over I2C alongside an RFM95W‑868 LoRa radio on SPI. It is powered via a 3.7 V Li‑ion cell with USB‑C charging up to 500 mA, complete with full battery protection, a robust 3.3 V rail tailored for Wi‑Fi burst currents, and per‑peripheral power gating to enhance energy efficiency. Core Features • MCU: ESP32‑S3‑MINI‑1‑N8 equipped with an onboard PCB antenna for 2.4 GHz Wi‑Fi/BLE, ensuring optimal wireless performance. • Sensors: Integrated ENS161 and ENS210 sensors utilize a shared I2C bus with controllable 4.7 kΩ pull‑ups for streamlined communication. • LoRa Radio: The RFM95W‑868 module, connected via SPI, enables long‑range communication at 868 MHz. Power & USB‑C Connectivity • Battery: A reliable 3.7 V 1200 mAh Li‑ion battery connected via a right‑angle JST‑PH 2‑pin connector features built‑in battery protection. • Charging: The USB‑C receptacle, with CC resistors and TVS protection on D+/D− along with series resistors, supports fast, safe charging with a current limit of 500 mA. • Regulation: A dedicated 3.3 V regulator capable of handling Wi‑Fi burst currents coupled with bulk and high‑frequency decoupling ensures stable operation, supported by status LEDs indicating power and charge states. Low‑Power Control • Peripheral Management: Load switches allow selective power‑gating of the ENS161, ENS210, and RFM95W modules, controlled directly by ESP32‑S3 GPIOs. • Energy Efficiency: Controllable I2C pull‑ups minimize idle current, vital for prolonged battery life in IoT applications. RF and Antenna Integration • 2.4 GHz: Utilizes the integrated PCB antenna on the ESP32‑S3 with proper ground/metal keep‑out zones for optimal signal integrity. • 868 MHz: Features a controlled‑impedance feed from the RFM95W to a PI matching network (C‑L‑C pads) with flexible antenna options—selectable via SMA connector, chip antenna, or PCB trace—and includes RF ESD protection. Connectivity & Debug Features • USB‑C Interface: Provides secure data connectivity with integrated safeguards and proper terminations. • Debugging: A comprehensive programming/debug header exposes EN, BOOT, and UART lines, with test points on key rails and buses (3V3, VBAT, SCK, MOSI, MISO, SDA, SCL, RESET/EN, GND) to simplify development and troubleshooting. Design Verification • Rigorous ERC/DRC and decoupling checks ensure adherence to component ratings and optimal signal routing. • Maintain RF keep‑outs and impedance‑controlled traces for both 2.4 GHz and 868 MHz paths, securing reliable performance even during high‑intensity operations. #IoT #ESP32S3 #LoRa #LowPowerDesign #USB-C #WirelessConnectivity #BatteryPowered #RFDesign

Smart Wellhead Controller V1.1: ESP32 + LoRa Industrial IoT Node with Solar Power, Deep-Sleep Leak Sensing, and OLED HMI. Now upgraded with a solar charging and battery management stage featuring a TP4056/CN3791 charger IC, power-path switching, Li-ion battery protection, and integrated 3.3 V rail supply. #PowerBlock #SolarCharging #BMS

SX1276 LoRa RF Test Board with USB-C Power, On-board USB-SPI Bridge Control, TCXO Clock, and 915 MHz 50 Ω RF Front-End

Falcon One v1 – Compact STM32-Based GNSS + LoRa 915 MHz Telemetry Node with LiPo Power and USB-C

VikingBoard: Multi-Wireless Expansion Board with WT32-SC01 Wi-Fi/BT, LoRa CC1101, NRF24L01+, GPS, Haptic Drivers, and Multi-Rail Power Management (+3V3_IO, +3V3_RF, +3V3_KBD, +5V_SYS, GND) #multi-wireless #expansion #power-management

ConexTeam LoRa Node. Control load state.

1.1 BLE Beacon Tags – Dual-Mode (BLE + LoRa) Installation: Mounted on safety helmets. Specification Requirement Communication Protocols BLE 5.0+ and LoRaWAN 1.0.4 Class A/B BLE Range Up to 150 meters LoRa Range > 5 km Battery Life BLE: ≥ 5 years; LoRa: ≥ 8 years Indoor Accuracy 1–5 meters using BLE Outdoor Accuracy 1–10 meters using LoRa + IMU + AI (no GPS on tag) Sensors 3-axis IMU, optional T&H, fall detection Alert Features SOS button, red LED, buzzer, vibration motor IP Rating IP67 minimum Operating Temperature -20°C to +70°C Certifications IECEx, IPSEC, FCC, CE, RoHS, REACH Branding White label with client logo

The "Green Dot 2040E5" Board is a Node that interfaces RS485 Sensor probes and can log information to the cloud using LoRa Connectivity. It uses the XIAO RP2040 and the LoRa-E5 (STM32WLE5JC) modules from Seeed Studio to do its magic. It also has amazing power management capabilities (Solar charging, Battery protection, etc) that make it very useful for IoT applications #Seeed #XIOA #LoRa #RP2040 #IoT

The LoST 3296 board features an Low Power STM32, an RFM95 Module for LoRA connectivity and a connector to interface different sensors. You can hook up a UART module, I2C module and a module using the RS485. The board is powered by the USB-C port

connent ESP32-WROOM-32 microcontroller with 10 BME688 sensors using CD74HC4066: Type: 4-Channel Analog Multiplexer and RAK811 LORA module

small UGV based with 4x brushless motor drivers Wifi and lora connectivity:battery connection is xt-90 pcb:) :RPI 4 mount with uart connectivity to EPS32-s3