(AL8805W5) The PicoBuck LED Driver is an economical and easy to use driver that will allow you to control and blend three different LEDs on three different channels. By default, each channel is driven at 330mA; that current can be reduced by either presenting an analog voltage or a PWM signal to the board. Version 12 of the board adds a solderable jumper that can be closed to increase the maximum current to 660mA. The new voltage regulator also increased the voltage rating on the various components on the board, allowing it to be used up to the full 36V rating of the AL8805 part.

A small, simple display for household information over MQTT. Based around the ESP12F chip, with an integrated 128x64 OLED display for information visualization, and 20x LEDs to display general status information.

The best way to have a friend is to build one. Jellybean is a robot friend whose gonna be right with you. Jellybean has been designed with a number of sensors to be able to interact with the environment and with the owner.

Raspberrypi Pico-based sampler, sequencer + drum machine w/ an embedded speaker, Adafruit I2S amplifier and momentary step switches, evoking the tr808 synthesizer ⁠

A discrete 555 timer plug-in replacement composed of 26 transistors and 16 resistors. #N555 #transistor #resistor

PCB that sends ambient temperature and high resolution analog data over a CAN bus for a FSAE electric car. Runs off a Teensy 4.0 and has connection pins for separate external analog sensors.

This project is a Gesture Light Switch Relay Reference Design. It involves an STM32 microcontroller (STMicroelectronics) that interacts with an APDS-9960 sensor (Broadcom) to detect hand gestures. The gesture data is used to control a Toshiba TLP175A relay and an Everlight tri-color LED to switch the light and change colors, respectively. Power is supplied by a Diodes Incorporated's AP2112K-3.3TRG1 regulator. #referenceDesign #edge-computing #edgeComputing #stm #relay #sensors #reference-design

This device will be connected to computer through type-C and recognize as MIDI device. User can change two effects(A and B) from lists, effect speed(Tempo) and volume.

The Texas Instruments MSP430FR604x and MSP430FR603x family comprises highly integrated ultrasonic sensing and measurement system-on-chips (SoCs) designed specifically for water and heat metering applications. The featured components, including MSP430FR6047, MSP430FR60471, MSP430FR6045, MSP430FR6037, MSP430FR60371, and MSP430FR6035, deliver best-in-class ultrasonic water flow measurement with ultra-low power consumption. These microcontrollers excel with an active mode current consumption of approximately 120 µA/MHz and a standby mode power draw as low as 450 nA with a real-time clock (RTC) enabled. Key functionalities include a high-precision differential time-of-flight (dTOF) accuracy of less than 25 ps, integrated analog front-end, programmable pulse generation (PPG), and an analog comparator. They also interface directly with standard ultrasonic sensors up to 2.5 MHz and feature up to 256KB FRAM, robust RAM options, and integrated LCD drivers for up to 264 segments. The embedded low-energy accelerator (LEA) enhances digital signal processing capabilities, making these components ideal for battery-powered metering solutions. Peripherals include multiple enhanced serial communication interfaces, high-performance ADCs, DMA controllers, and a suite of timers and encryption modules. These features combine to offer a powerful solution for high-accuracy, low-cost, and ultra-low-power metering applications.

This is a simple charger modul that can be connected to a DC generator or solar panel at the input and a battery at the output

This project designs a Linux Single Board Computer using STM32MP157FAC1, featuring DDR memory, a power management IC, USB and SD card interfaces, and essential user controls, aimed at versatile embedded applications.

Change History from V1: -13.56MHz tuning -larger instruction font -put some stuff on the back I wanted to create a business card that has some functionality and shows off a bit of my portfolio IRL: -NFC to my flux page -here's the awesome [instructables](https://www.instructables.com/PCB-Business-Card-With-NFC/) -Put a bunch of modules on it Find the BoM [here](https://www.digikey.com/short/2db2vnmp)

This is a reference design of TPS56339 DC-DC Converter IC with input voltage 4.5-24V and output 5V and 3A #dcdc #ti #power #3A #5V #referenceDesign #powermanagement #texas-instruments #template #reference-design

An ATtiny13 is more than sufficient to control almost any number of NeoPixels via an IR remote. The NeoController was originally developed as a tester for 800kHz NeoPixel strips. Since there was still so much flash left in the ATtiny13, an IR receiver was integrated so that some parameters can be controlled with an IR remote control. In this way, it is also suitable as a simple and cheap remote-controlled control unit for NeoPixels. Due to its small size (21.6mm x 11.4mm), it can be soldered directly to the LED strip without any problems. The power supply via a USB-C connection enables currents of up to 3A. There is still more than a third of the flash memory left for additional ideas.

A universal PD module that outputs 5-20V and a maximum power of 100W

Guitar pedal starter template based on project by Mark Wu. Includes schematic and PCB layout for basic DIY pedal hardware. This includes two 1/4" jacks (one for input and one for output), a 9V power supply (including LED), a 3PDT true bypass wiring setup, and an example potentiometer that can be copy/pasted throughout the circuit. The headers are meant to be unpopulated so that wires can be soldered to the pads. PCB design rules imported from the JLCPCB 2-layer stackup template. #template

The nRF52840 DK is a versatile single board development kit for Bluetooth 5, Bluetooth mesh, Thread, Zigbee, 802.15.4, ANT and 2.4 GHz proprietary applications on the nRF52840 SoC. It also supports development for the nRF52811 SoC.

This is the multipurpose PCB that works with Arduino Nano, a way that you can run 2 Stepper motors, 2 DC motors, 2 Servo motors at the same time and this is not it you can even connect BT module, rotary encoder, I2C device, potentiometer at same time. This PCB is very much helpful in building any project and no need to worry about messy wire connections.

This is a recreation of the [EV5920-5048-V-00A](https://www.monolithicpower.com/en/ev5920-5048-v-00a.html) from MPS which demonstrates a MP5920 Hot-Swap controller commanding 5 MP5048 e-fuses in parallel. WIP Items: -Routing In flux, this project demonstrates hierarchal design through the use of modules. Additionally, parametric symbols are used extensively to improve schematic cleanliness. Components in the canvas are locked because their positions correspond to the same positions as the original layout. Changelog from Original MPS Design: - Not including GPIO2 or GPIO3 as included in the original board due to NC pin name on the IC. - PC1 and PC2 footprints are 5mm in pitch and 12.5mm in diameter rather than the 16mm diameter in the original layout. This change corresponds with the selected part more accurately. -Renamed Designators to be More Verbose

The SparkFun ZOE-M8Q GPS Breakout is a high accuracy, miniaturized, GPS board that is perfect for applications that don't possess a lot of space. The on-board ZOE-M8Q is a 72-channel GNSS receiver, meaning it can receive signals from the GPS, GLONASS, BeiDou, and Galileo constellations. This increases precision and decreases lock time and thanks to the onboard rechargable battery you'll have backup power enabling the GPS to get a hot lock within seconds! Additionally, this u-blox receiver supports I2C (u-blox calls this Display Data Channel) which made it perfect for the Qwiic compatibility so we don't have to use up our precious UART ports. Utilizing our handy Qwiic system, no soldering is required to connect it to the rest of your system. However, we still have broken out 0.1"-spaced pins in case you prefer to use a breadboard.

Integrated 4-layer ROV main control board for 48 V tether-powered underwater vehicle, with onboard 48 V to 12 V/5 V/3.3 V electronics power conversion, STM32F407 control, Jetson Nano interface, sensors, ESC PWM signal outputs, RS485/Ethernet tether interfaces, and conformal-coated underwater-enclosure constraints.

12V LiFePO4 power distribution board requirements package: 150 mm x 100 mm 2-layer SMD PCB with 12V battery input, input protection, 12V-to-5.1V buck conversion, six USB-C power outputs, 3.3V logic rail, current/voltage monitoring, test points, board-edge connectors, and JLCPCB-aligned fabrication outputs.

A self-contained “retro PC” platform built around the ESP32, exposing classic PC-style IO: VGA video, PS/2 keyboard/mouse, audio-out to an onboard speaker, microSD storage, plus USB-C for power and USB-UART for programming/debug.

This is a MAX30102 based integrated pulse oximetry and heart-rate monitor biosensor module #wearable #pulse #heartRate #oximeter #MAX30102 #referenceDesign

This compact breakout board makes it easy to add high-quality audio output to your microcontroller projects using the MAX98357A/B Class D audio amplifier. Perfect for Arduino, ESP32, Raspberry Pi, or any microcontroller with I2S output capabilities. Features High-Performance Audio: Delivers Class AB audio quality with Class D efficiency (92% efficient at 1W) Powerful Output: 3.2W into 4Ω speakers at 5V supply Clean Sound: Low distortion (0.013% THD+N at 1kHz) Wide Supply Range: Operates from 2.5V to 5.5V Simplified I2S Interface: No MCLK required, just BCLK, LRCLK, and DIN Selectable Gain: Solder jumpers for easy gain selection (3dB, 6dB, 9dB, 12dB, or 15dB) Channel Selection: Configure for left, right, or combined (mono) output Filterless Design: No need for external output filtering components Compact Form Factor: Minimal board space with optimized layout Applications Smart speakers and voice assistants Portable audio devices IoT audio projects Gaming devices and sound effects Educational audio projects Digital instrument amplification The FLUX MAX98357 breakout board requires only three I/O pins plus power, making it the perfect audio solution for projects where simplicity and sound quality matter.