• ESP32 IMU Template

    ESP32 IMU Template

    This project is a small 100mm X 100mm quadcopter controlled by ESP32 and MPU-6050 Template #drone #motorController #ESP32 #controller #motor #helicopter #referenceDesign #project #quadcopter #MPU6050 #template

    vasy_skral

    2 Stars

  • 3DO In-Game Reset Mod

    3DO In-Game Reset Mod

    A simple 3DO in-game reset mod. MCU sniffs controller data and fires a reset signal to the console when L+R+X+P buttons are pressed.

    robertdalesmith

    2 Stars

  • ATTINY841 BMS

    ATTINY841 BMS

    DIY BMS using ATTINY841-SSU this hardware has a higher balance current, fuse and TVS diode to help with voltage spikes. Most importantly, an external crystal to the micro controller (attiny841) which means the device is more reliable in low voltage situations

    flux

    &

    2 Stars

  • 7-Segment Controller

    7-Segment Controller

    This is a 7-segment controller. It runs on a 3-bit counter so the count is from 0-7. Buttons to toggle reset, pause, increment. Knobs to control speed and lighting configuration. Try the simulation here: https://www.flux.ai/jbreidfjord-dev/7-seg-3-bit-counter

    jlamflux

    57 Comments

    1 Star

  • ESP32 Robot Controller

    ESP32 Robot Controller

    Control board for autonomous or radio-controlled robots. It has inputs to connect distance sensors and encoders for autonomous mode. It can be radio controlled by the ESP32 bluetooth or by connecting a Flysky RC controller receiver to the IBUS port. It also has 3 push buttons and you can connect some kind of display by I2C to visualize and select configuration modes. Forked from original project: https://www.flux.ai/jr98/esp32-robot-controller

    jharwinbarrozo

    18 Comments

    1 Star

  • Pulse Width Modulation (PWM) Controller

    Pulse Width Modulation (PWM) Controller

    This project is a Pulse Width Modulation (PWM) Controller, built around an LM555 timer IC. It controls a load connected to a MOSFET, with adjustments via a potentiometer, and uses capacitors, resistors and diodes for various functions. #PWM #controller #project #Template #projectTemplate

    anchal23

    &

    +2

    11 Comments

    1 Star

  • STM32F4 Flight Controller Template oB1U

    STM32F4 Flight Controller Template oB1U

    This is a STM32F4 Flight Controller template with 6-axis Accelerometer, Gyroscope. With OSD generator MAX7456EUI. #drone #flightController #STM32F405 #controller #OSD #video #referenceDesign #project #MPU6000 #template

    selcukc

    1 Comment

    1 Star

  • BLE Controller Template 5p8p

    BLE Controller Template 5p8p

    This is a BLE Controller project based on E73-2G4M04S1A module with SoC nRF52810 on board. Can be used to control RC cars, robots, planes, drones, etc #robotics #nRF52810 #E73 #Ebyte #BLE #referenceDesign

    tbartelmess

    1 Comment

    1 Star

  • ESP32 RS485 (Modbus) Controller Module 02e3 8a70 11db

    ESP32 RS485 (Modbus) Controller Module 02e3 8a70 11db

    This project is a controller module that uses the ESP32-WROOM-32E and the MAX3485 to communicate with Modbus devices. It has a USB-C port for power and data, a voltage regulator for stable operation. It also has a CH340C chip for USB to serial conversion. #referenceDesign #project #ESP32 #ESP32WROOM #RF #WIFI #MCU #reusable #module #simple-embedded #espressif #template #MAX3485 #RS485 #maximintegrated

    tyson0906

    1 Comment

    1 Star

  • Qwiic PC Fan Controller

    Qwiic PC Fan Controller

    The Qwiic PC Fan Controller allows you easily control almost any PC fan over the Qwiic bus using the on board ATtiny microcontroller and control firmware. The control firmware monitors the tachometer output of the fan in order to implement PI Control over the fan speed, allowing you to set your desired speed in real units.

    adrian95

    &

    1 Comment

    1 Star

  • SMC3 3DOF Motion Controller

    SMC3 3DOF Motion Controller

    Arduino-compatible SMC3/SimTools 3-DOF motion controller for three 12 V worm-drive motors, Hall feedback sensors, dual USB-C interfaces, and E-stop safety input.

    evanrowlands

    1 Star

  • STM32 CAN Stepper Controller

    STM32 CAN Stepper Controller

    Standalone STM32F446RE-header CAN/RS485 stepper motor controller PCB with external 5V input, 3.3V logic rail, CAN protection, SWD/reset, level-shifted STEP/DIR/ENABLE outputs, and split-ready modular layout.

    kaanolgun

    1 Star

  • Industrial Welding IoT Controller

    Industrial Welding IoT Controller

    Industrial Welding IoT Controller — schematic and placement preserved; PCB routing cleanup still required before manufacturing.

    genzzprotech

    1 Star

  • ESP32-S3 Handheld Controller

    ESP32-S3 Handheld Controller

    Production-intent ESP32-S3 handheld controller with USB-C sink power, ST7789 SPI TFT, 5-way controls, class-D speaker output, and factory test pads on a 4-layer PCB.

    3fathleticsllc

    1 Star

  • 110 VAC PDLC Controller

    110 VAC PDLC Controller

    110 VAC mains-input PDLC controller redesign for 25 W+ load with protected front end, rectified HV bus, auxiliary control supply, and preserved downstream square-wave output control.

    rgallizzi

    &

    1 Star

  • Bluetooth RC Car Controller

    Bluetooth RC Car Controller

    Bluetooth RC car controller using ESP32-WROOM-32E, TB6612FNG dual H-bridge, XL4015 5V buck module, DC barrel battery input, dual 2-pin motor screw terminals, 1000uF VM bulk capacitor, 100nF decoupling, 10k EN pull-up, 30 mil power traces, 10 mil signal traces, and ESP32 antenna edge keep-out.

    feliperiquelme

    1 Star

  • Nintendo Controller

    Nintendo Controller

    Original Nintendo Entertainment System (NES) controller. Just like the originals, it uses a CD4021B 8-bit shift register to send serial data of the button state to the console.

    robertdalesmith

    1 Star

  • Flight Controller

    Flight Controller

    This is a custom flight controller based around a STM32F103C8T6. It contains a BMP280 to measure the altitude of a drone, an ICM-42688-P that contains an accelerometer and gyroscope for motion control. The input voltage should be 12V and is set up to work with a LiPo battery.

    hakeem02

    1 Star

  • Arduino WS2812b Controller Shield

    Arduino WS2812b Controller Shield

    The Arduino WS2812b Controller Shield is a shield designed to offload the implementation of the WS2812b protocol to the shield. It is implemented on an ATtiny85, and the Arduino communicates with the shield over standard SPI. The code for the ATtiny85 can be found at https://github.com/k3jph/ws2812b-spi-controller

    k3jph

    1 Star

  • Midi Drumpad Controller

    Midi Drumpad Controller

    A versatile MIDI drum pad controller with 16 responsive buttons, potentiometers, and optimized circuitry, designed to seamlessly integrate into any music production setup.

    sochii

    1 Star

  • Engine Controller

    Engine Controller

    Welcome to your new project. Imagine what you can build here.

    blaravie

    12 Comments

    1 Star

  • ESP32 Robot Controller | AI Design Review Tutorial [Example] 3o6U

    ESP32 Robot Controller | AI Design Review Tutorial [Example] 3o6U

    Spot the mistake! Learn how to use AI to conduct a design review on an ESP32-based control board. This project is ideal for autonomous or radio-controller robots featuring inputs for sensors, encoders, and a Flysky RC receiver, plus an I2C display for configuration.

    dmit

    5 Comments

    1 Star

  • Resistive Touch Screen Controller - STMPE610

    Resistive Touch Screen Controller - STMPE610

    This breakout board features the STMPE610, which has both I2C and SPI interfaces available. There is also an interrupt pin that you can use to indicate when a touch has been detected to your microcontroller or microcomputer.

    adrian95

    &

    3 Comments

    1 Star

  • ✅ Raspberry Pi LEGO 9V Motor Controller

    ✅ Raspberry Pi LEGO 9V Motor Controller

    PWM-capable low-side MOSFET driver for controlling a 9 V LEGO motor from a Raspberry Pi 3.3 V GPIO signal, sized for up to 1.4 A stall/current peaks.

    dacre

    &

    1 Comment

    1 Star

  • ESP32 Robot Controller | AI Design Review Tutorial [Example]

    ESP32 Robot Controller | AI Design Review Tutorial [Example]

    Spot the mistake! Learn how to use AI to conduct a design review on an ESP32-based control board. This project is ideal for autonomous or radio-controller robots featuring inputs for sensors, encoders, and a Flysky RC receiver, plus an I2C display for configuration.

    jrvc18

    1 Comment

    1 Star