First in the world hands-free Otherside communication device! You need only the board, spirit or ghost don't need to move the ouija anymore. Symbols will light up from the inside so you will be able to read your messages and spirit or ghost just need to turn on a red bottom entry LED. Two MEMS microphones allow your interlocutor to clearly hear your questions. WiFi connectivity gives you an opportunity to "dial" without a Medium anytime anywhere. And it has Bluetooth as well, because: "Everything is better with Bluetooth"! This board is powered by a single 10440(AAA) LiFePO4 battery that gives you up to 2 hours of seance. Designed by Vasyl Skral

Test Project for the green dot project.

This project is a reference project for ESP32-S3-WROOM-1 to develop your IoT ideas. The board has 3 LEDs, USB C for firmware, EN and BOOT buttons, and 2 IO connectors for development #IoT #WiFi #MCU #RF #ESP32 #referenceDesign #project

RP2040 Dual TLC5940 High-Current LED Driver Board

Template for RT1062 Teensy 4.1 series ARM® Cortex®-M7 MPU Embedded Evaluation Board #template #project-template

A simple 1-to-3 buffered mult - Eurorack-talk for an audio/CV distributor The board itself is a 3U 4hp rack-mountable module This circuit was designed by https://www.skullandcircuits.com/utilities-buffered-multiple/ and their T&Cs apply to commercial use (I built these for myself)

Control board for autonomous or radio-controlled robots. It has inputs to connect distance sensors and encoders for autonomous mode. It can be radio controlled by the ESP32 bluetooth or by connecting a Flysky RC controller receiver to the IBUS port. It also has 3 push buttons and you can connect some kind of display by I2C to visualize and select configuration modes.

The unknown project

Template for Raspberry Pi 5 Model Shield. Include an official pinout so you will always know Raspberry Pi names, the alternative roles of pins, which one is SDA, or SCL, etc. On PCB you can find the 3D model of the Raspberry Pi itself along with the board outline on the silkscreen. #RaspberryPi #Raspberry #RaspberryPi5 #raspberry #Pi #RPi #Shield #template #project #project-template

This Weather Station Logger project employs the versatile ESP32 microcontroller board, integrated with an SD card slot for data storage. It features a USB interface for easy programming and is efficiently powered by a single 18650 battery, complete with a protection circuit for safe operation. #iot #esp32 #lora #weather #edgecomputing

Use this template if you're planning to get your board manufactured in OSHPARK. It has the via min/max and trace width constraints already baked as global rules. #project-template #template #manufacturer-design-rules OSHpark 4-layer stackup specs: Top overlay or silkscreen: 1 mil thick Top solder mask or solder resist: 1 mil thick Top copper: 1.7 mil thick on 1 oz copper Dielectric: 7.96 mil thick FR408HG 2113 Mid layer 1: 0.68 mil thick on 0.5 oz copper Dielectric core: 39 mil thick FR408HR Mid layer 2: 0.68 mil thick on 0.5 oz copper Dielectric: 7.96 mil thick FR408HG 2113 Bottom copper: 1.7 mil thick on 1 oz copper Bottom solder mask or solder resist: 1 mil thick
Bottom overlay or silkscreen: 1 mil thick

This project is a 6-output irrigation control board with pump and other device support. It features 8 connectors, 2 GPIO pins each, and a GC9A01A display. The board is powered by an STM32L073V8T6 microcontroller and has 6 LEDs connected to GPIO pins. #irrigationcontrol #STM32 #GPIO #GC9A01A #LEDs.

Project Overview: This project is an enhanced LED blinking circuit that goes beyond a simple 555 timer-based design. It incorporates additional features such as random blinking patterns, speed control, and a start/stop function. The project utilizes a microcontroller, such as an Arduino or Raspberry Pi, to control the blinking patterns, speed, and start/stop functionality. LED Blinking: The board features a total of 8 LEDs that blink in various random patterns. When the board is powered on, even before user interaction, the LEDs start blinking randomly, creating an eye-catching display. Each LED has its own current-limiting resistor to ensure proper current flow and prevent damage. The microcontroller is programmed to generate random blinking patterns for the LEDs, ensuring that the LEDs do not blink in a predictable or sequential order. This random blinking adds an element of unpredictability and visual interest to the project. Speed Control: The board includes two speed control buttons that allow the user to adjust the blinking speed of the LEDs. Button 1 is designated as the "fast" button, increasing the blinking speed when pressed, while Button 2 is designated as the "slow" button, decreasing the blinking speed when pressed. The speed control provides a range of blinking speeds, from a slow, gradual blink to a rapid, strobe-like effect. The microcontroller monitors the state of the speed control buttons and adjusts the blinking speed accordingly. Start/Stop Functionality: A third button serves as a start/stop control. When pressed, it toggles the blinking of the LEDs on or off. This allows the user to freeze the blinking pattern at any desired moment or resume the blinking when desired. The microcontroller handles the start/stop functionality by turning the LEDs on or off based on the state of the start/stop button. Manual Speed Adjustment: In addition to the speed control buttons, the board includes a potentiometer or variable resistor. This component allows the user to manually adjust the blinking speed of the LEDs by turning the knob or sliding the control. The manual speed adjustment provides more precise and customizable control over the blinking speed compared to the preset speeds of the buttons. The microcontroller reads the analog value from the potentiometer and adjusts the blinking speed accordingly. Power and Connectivity: The board is powered through a USB-C or USB-micro B connector, allowing it to be easily connected to a power source such as a computer or wall adapter. A voltage regulator may be included to ensure a stable and appropriate voltage supply to the components. A power switch is incorporated to conveniently turn the board on or off.

sEMG-DAQ is a wearable 6 channel data acquisition unit for capturing surface electromyographic (sEMG) signals from human arm muscles using SJ2-3593D jack connectors while conditioning, digitizing, processing and transmitting them as sEMG data to an external AI accelerated board through an SM12B-SRSS IDC connector where AI models are run for various applications including robotic control, muscle signals medical assessment and gesture recognition. The board leverages an INA125P instrumentation amplifier together with filter stages utilizing LM324QT op-amps for conditioning and an STM32G4A1VET6 microcontroller for the digitization, processing and data transmission of the signals. Since AI models can only be as good as the data, the design of such a DAQ is necessary to ensure clean, reliable and real-time data for AI applications requiring sEMG data. The board also has USB-FS and JTAG to cater for debugging. The power (5V) is fed through a screw terminal and is regulated by two LDK320AM LDO regulators to offer 5V, 3.3V and 1.8V to meet the requirements of various components on the board.

This is a board for a robotic arm controlled by Particle Argon. Settings can be made using a display module that connects to the board. You can teach him to draw or cook. Just use your imagination!

Template for ATmega32U4 Arduino Micro AVR® ATmega AVR MCU 8-Bit Embedded Evaluation Board #project-template #template #arduino #micro

Build your own Modular LED Sign! This design prioritizes accessibility which means that the BoM can be ordered on Amazon and that everything was designed with solder-ability in mind. NOTE: This board is still an unfinished prototype that has not been built and verified. Operating Instructions: 1. [Important!] Power your buck converter and adjust the output voltage to 1.5V output before attempting to power the LEDs. If you cannot power the buck converter, just turn the potentiometer counterclockwise to its maximum setting.

This BMS 10s board for Zinc ion batteries is made of water, zinc, and carbon. The maximum battery voltage is 1.8v. #BMS #zinc #esp32#battery

ATTINY85 to toggle the LEDs of this cute board.

IMPORTANT NOTICE: Hey, I opened editing permissions and this doc is broken, see the frozen version here: https://www.flux.ai/markwuflux/on-air-markwu2001-remix-r1-backup-freeze-0b49 R1 changes: -Changed LED part to Red LEDs -adjusted resistor value of buck converter -Changed source for USB-C Connector -Removed exposed soldermask on buck converter with negative soldermask expansion -Order with black soldermask Modified by markwu2001: - Adjustable Brightness, - 85-90% Drive Efficiency - <5W Operation (Can use 5V 1A Plug) This project can be purchased from LCSC Original Description: Daddy's second circuit board. A sign to let my wife know when I'm on a call. Activates with a slide switch and is powered by USB-C.

Board for air-powered soft robots. Board contains 4 air pumps powered by a 12.4v li-on battery and controlled by fixed buttons

A simple 1-to-3 buffered mult - Eurorack-talk for an audio/CV distributor The board itself is a 3U 4hp rack-mountable module This circuit was designed by https://www.skullandcircuits.com/utilities-buffered-multiple/ and their T&Cs apply to commercial use (I built these for myself)

A simple 1-to-3 buffered mult - Eurorack-talk for an audio/CV distributor The board itself is a 3U 4hp rack-mountable module This circuit was designed by https://www.skullandcircuits.com/utilities-buffered-multiple/ and their T&Cs apply to commercial use (I built these for myself)

Template for Arduino Mega2560 Shield. On PCB you can find the board outline on the silkscreen. #Shield #arduino #template #mega #2560 #ATMEGA2560 #template #project #project-template

This is a WiFi relay board based on ESP32-H2 WiFi module. It have AC-DC power supply with output 12V and relay for controlling voltage #esp32 #project #Relay #wifi #esp32-h2 #iot #template