Schematic for Dreadful Gray Lightcycle

Marine Start Panel PCB Design

flux

0:00

Autopilot

Work completed

Bottom-center terminals updated:
- Removed old 2-pos blocks J2–J5
- Added new 4-pos blocks J2, J3, J4, J5 and locked them
Relay and driver/diode locks:
- Locked K1–K5
- Locked Q1–Q5 and D2–D6
ESP32 decoupling added:
- C3 (100 nF), C4 (4.7 µF) placed and locked
Front-end circuits integrated:
- ADC dividers R2–R9, RC filters R10–R13 and C5–C8 added and locked
- Tach op-amp U3, R14, C9 placed ≥ 20 mm from relays and locked
- Light sensor D7, U4, R15, C10 added near top edge and locked
- Front-end nets connected to J9/J10 and MCU pins, portals locked
SeaTalk interface added:
- Opto-isolator U6 and level shifter U7 placed adjacent to J10 and locked

Tasks not done

Due to environment constraints, I could not reposition components or define the copper keep-out zone:

Reposition relays for tight top-right cluster ([K1]–[K5])
Slide drivers ([Q1]–[Q5]) and diodes ([D2]–[D6]) within 3–5 mm of coils
Relocate power stage parts ([U2], [D1], [F1], [R1], [C1], [C2]) within 20 mm of J1 and route high-current paths
Define and lock a 12 × 12 mm antenna no-copper zone around U1

Success criteria

✅ Bottom-center zone: 4-pos terminals replaced and locked
❌ Relay cluster & driver/diode repositioning: not repositioned
❌ Power-stage relocation & routing: not relocated
✅ ESP32 decoupling caps & bulk cap added; ❌ antenna keep-out zone: not defined
✅ Right-edge front-end circuits, tach-op amp, light sensor, SeaTalk interface added and locked
✅ All new placements respect locked anchors

Next step

Proceed to Schematic Review to verify connectivity, functional grouping, and update copper keep-out zones before finalizing PCB layout.

56 days

Ready.

Reviews

Electrical Rule Checks

Missing Footprints

Reports parts that have no footprint.

Design Rule Checks

Overlapping Copper

Reports copper elements that are shorting.

Invalid Layer

Reports nodes that are assigned to a layer that doesn't exist in the layout stackup.

Component Overrides • 1

	Designator	Ruleset
	Footprint	Override rule for Footprint

Airwires • 18

	Designators	Net
	C5:P1, R3:P2	J9_1
	R2:P2, R3:P2	J9_1
	U1:IO32, J9:1	J9_1
	U1:IO32, R2:P2	J9_1
	C7:P1, J9:2	J9_2
	R4:P2, R5:P2	J9_2
	U1:IO33, C7:P1	J9_2
	U1:IO33, R5:P2	J9_2
	J10:1, C8:P1	J10_1
	R6:P2, R7:P2	J10_1
	R6:P2, U1:IO35	J10_1
	U1:IO35, C8:P1	J10_1
	R8:P2, C6:P1	J10_2
	R9:P2, R8:P2	J10_2
	R9:P2, U1:IO34	J10_2
	U1:IO34, J10:2	J10_2
	U1:IO27, U4:OUTPUT	LIGHT_OUT
	U1:IO4, U3:OUT1	TACH_OUT

Deprecated Rules

Reports nodes that are using rules that are not supported anymore.

Layers with Multiple Fills

Reports layers that have multiple copper fills of different nets. Make sure the Connected Layers rule value of nets with fills is valid.

Floating Copper

Detect any via, trace or copper fill island that is not connected to any net.

Protected Intrusions

Reports intrusions from objects of other nets into polygons or fills that have the Protected layout rule applied.

Manufacturing

Manufacturer Part Number • 29

	Designator	MPN
	C1	None
	C2	None
	C3	None
	C4	None
	C5	None
	C6	None
	C7	None
	C8	None
	C9	None
	C10	None
	Hole1	None
	Hole2	None
	Hole3	None
	Hole4	None
	R1	None
	R2	None
	R3	None
	R4	None
	R5	None
	R6	None
	R7	None
	R8	None
	R9	None
	R10	None
	R11	None
	R12	None
	R13	None
	R14	None
	R15	None

Parts Available

Beta

Checks that all parts have a part number and are available from distributors.

System Checks

Auto-Layout

Beta

Reports issues with Auto-Layout if Flux cannot route something or must ignore a configuration.

Passive Components

Resistor Power Rating

Beta

Checks that the power traveling across a given resistor is under its rating with 50% headroom.

Learn more

Pull Up/Pull Down Presence

Beta

Checks that IC pins that require pull up or pull down resistors have them.

Learn more

Capacitor Voltage Rating

Beta

Checks that capacitors have appropriate voltage ratings to prevent overheating and ensure reliable circuit operation.

Ground
A common return path for electric current. Commonly known as ground.
jharwinbarrozo
20.5M
Net Portal
Wirelessly connects nets on schematic. Used to organize schematics and separate functional blocks. To wirelessly connect net portals, give them same designator. #portal
jharwinbarrozo
43.0M
Power Net Portal
Wirelessly connects power nets on schematic. Identical to the net portal, but with a power symbol. Used to organize schematics and separate functional blocks. To wirelessly connect power net portals, give them the same designator. #portal #power
jharwinbarrozo
11.4M
Generic Resistor
A generic fixed resistor for rapid developing circuit topology. Save precious design time by seamlessly add more information to this part (value, footprint, etc.) as it becomes available. Standard resistor values: 1.0Ω 10Ω 100Ω 1.0kΩ 10kΩ 100kΩ 1.0MΩ 1.1Ω 11Ω 110Ω 1.1kΩ 11kΩ 110kΩ 1.1MΩ 1.2Ω 12Ω 120Ω 1.2kΩ 12kΩ 120kΩ 1.2MΩ 1.3Ω 13Ω 130Ω 1.3kΩ 13kΩ 130kΩ 1.3MΩ 1.5Ω 15Ω 150Ω 1.5kΩ 15kΩ 150kΩ 1.5MΩ 1.6Ω 16Ω 160Ω 1.6kΩ 16kΩ 160kΩ 1.6MΩ 1.8Ω 18Ω 180Ω 1.8KΩ 18kΩ 180kΩ 1.8MΩ 2.0Ω 20Ω 200Ω 2.0kΩ 20kΩ 200kΩ 2.0MΩ 2.2Ω 22Ω 220Ω 2.2kΩ 22kΩ 220kΩ 2.2MΩ 2.4Ω 24Ω 240Ω 2.4kΩ 24kΩ 240kΩ 2.4MΩ 2.7Ω 27Ω 270Ω 2.7kΩ 27kΩ 270kΩ 2.7MΩ 3.0Ω 30Ω 300Ω 3.0KΩ 30KΩ 300KΩ 3.0MΩ 3.3Ω 33Ω 330Ω 3.3kΩ 33kΩ 330kΩ 3.3MΩ 3.6Ω 36Ω 360Ω 3.6kΩ 36kΩ 360kΩ 3.6MΩ 3.9Ω 39Ω 390Ω 3.9kΩ 39kΩ 390kΩ 3.9MΩ 4.3Ω 43Ω 430Ω 4.3kΩ 43KΩ 430KΩ 4.3MΩ 4.7Ω 47Ω 470Ω 4.7kΩ 47kΩ 470kΩ 4.7MΩ 5.1Ω 51Ω 510Ω 5.1kΩ 51kΩ 510kΩ 5.1MΩ 5.6Ω 56Ω 560Ω 5.6kΩ 56kΩ 560kΩ 5.6MΩ 6.2Ω 62Ω 620Ω 6.2kΩ 62KΩ 620KΩ 6.2MΩ 6.8Ω 68Ω 680Ω 6.8kΩ 68kΩ 680kΩ 6.8MΩ 7.5Ω 75Ω 750Ω 7.5kΩ 75kΩ 750kΩ 7.5MΩ 8.2Ω 82Ω 820Ω 8.2kΩ 82kΩ 820kΩ 8.2MΩ 9.1Ω 91Ω 910Ω 9.1kΩ 91kΩ 910kΩ 9.1MΩ #generics #CommonPartsLibrary
jharwinbarrozo
1.5M
Generic Capacitor
A generic fixed capacitor ideal for rapid circuit topology development. You can choose between polarized and non-polarized types, its symbol and the footprint will automatically adapt based on your selection. Supported options include standard SMD sizes for ceramic capacitors (e.g., 0402, 0603, 0805), SMD sizes for aluminum electrolytic capacitors, and through-hole footprints for polarized capacitors. Save precious design time by seamlessly add more information to this part (value, footprint, etc.) as it becomes available. Standard capacitor values: 1.0pF 10pF 100pF 1000pF 0.01uF 0.1uF 1.0uF 10uF 100uF 1000uF 10,000uF 1.1pF 11pF 110pF 1100pF 1.2pF 12pF 120pF 1200pF 1.3pF 13pF 130pF 1300pF 1.5pF 15pF 150pF 1500pF 0.015uF 0.15uF 1.5uF 15uF 150uF 1500uF 1.6pF 16pF 160pF 1600pF 1.8pF 18pF 180pF 1800pF 2.0pF 20pF 200pF 2000pF 2.2pF 22pF 20pF 2200pF 0.022uF 0.22uF 2.2uF 22uF 220uF 2200uF 2.4pF 24pF 240pF 2400pF 2.7pF 27pF 270pF 2700pF 3.0pF 30pF 300pF 3000pF 3.3pF 33pF 330pF 3300pF 0.033uF 0.33uF 3.3uF 33uF 330uF 3300uF 3.6pF 36pF 360pF 3600pF 3.9pF 39pF 390pF 3900pF 4.3pF 43pF 430pF 4300pF 4.7pF 47pF 470pF 4700pF 0.047uF 0.47uF 4.7uF 47uF 470uF 4700uF 5.1pF 51pF 510pF 5100pF 5.6pF 56pF 560pF 5600pF 6.2pF 62pF 620pF 6200pF 6.8pF 68pF 680pF 6800pF 0.068uF 0.68uF 6.8uF 68uF 680uF 6800uF 7.5pF 75pF 750pF 7500pF 8.2pF 82pF 820pF 8200pF 9.1pF 91pF 910pF 9100pF #generics #CommonPartsLibrary
jharwinbarrozo
1.5M
Generic Inductor
A generic fixed inductor for rapid developing circuit topology. *You can now change the footprint and 3D model at the top level anytime you want. This is the power of #generics
jharwinbarrozo
15.1k
Terminal
An electrical connector acting as reusable interface to a conductor and creating a point where external circuits can be connected.
natarius
RMCF0805JT47K0
47 kOhms ±5% 0.125W, 1/8W Chip Resistor 0805 (2012 Metric) Automotive AEC-Q200 Thick Film #forLedBlink
jharwinbarrozo
1.2M
875105359001
10uF Capacitor Aluminum Polymer 20% 16V SMD 5x5.3mm #forLedBlink #commonpartslibrary #capacitor #aluminumpolymer #radialcan
jharwinbarrozo
1.2M
CTL1206FYW1T
Yellow 595nm LED Indication - Discrete 1.7V 1206 (3216 Metric) #forLedBlink
jharwinbarrozo
1.1M

Inspect

Dreadful Gray Lightcycle

Controls

Properties

Plan Step 3.2 Status

Availability & Pricing

Distributor		Qty 1
	Arrow	$20.51–$27.32
	Digi-Key	$29.73–$35.98
	LCSC	$26.60–$27.37
	Mouser	$38.48–$38.84
	TME	$33.05
	Verical	$18.14–$47.10

Assets

Welcome 👋

Flux helps you build PCBs faster with an AI teammate!

Create your account to collaborate, stay updated, fork your own version, and get instant answers from our AI agent.