Mono Audio Amplifier Design
1:18
Running design review.
Reviewing the bill of materials.
Analyzing the PCB layout.
Analyzing the schematic.
Looking for "recommended operating conditions, supply voltage range, output power, typical application circuit, gain configuration, bypass capacitor, output capacitor, speaker load guidance" in suppproductinfo.tsp?distId=10&gotoUrl=http%253A%252F%252Fwww.ti.com%252Flit%252Fgpn%252Flm386
Looking for "pinout and polarity of center pin and sleeve terminal" in pj-037a.pdf
Clarifying citation requirements.
Short answer: the schematic is close, but I would not call the PCB fully verified yet.
It is likely to function at a basic level as a low-power mono amplifier, but there are a few important limitations and one probable wiring issue that mean I can’t yet say “this will definitely work as intended.”
Verdict
| Area | Status | Why |
|---|---|---|
| Basic topology | Good | Stereo input is AC-coupled, summed to mono, level-controlled, then sent into U1, which is a valid single-supply audio amplifier topology. |
| Supply range | Good | U1 supports 5 V to 18 V, so your 5 V to 12 V target is within the datasheet range. |
| Speaker drive target | Not fully met | Your requested up to 3 W is not realistic with U1. TI’s datasheet example for this family is far below that, and the N-4 variant is characterized around 700 mW to 1 W max under favorable conditions, not 3 W. |
| Schematic correctness | Needs one fix/check | The potentiometer grounding appears inconsistent between earlier wiring and current schematic state. |
| PCB completeness | Not complete | DRC still reports 12 airwire errors, so the board is not fully routed yet. |
| Manufacturability | Mostly good | Parts are hobby-friendly: DIP and through-hole parts plus 0805 passives. |
This design follows the standard functional chain a project explanation should describe: input, conditioning, amplification, and output
1. Input coupling and stereo-to-mono summing
- J1 provides L/R/GND input.
- C1 and C2 are 1 uF DC-blocking capacitors, so any source DC offset is removed before the audio reaches the summing network.
- R1 and R2, both 1 kOhm, passively sum left and right to mono. That is a standard safe way to combine stereo channels without directly shorting them together.
- The summed signal feeds the 10 kOhm pot RV1.
- The wiper of RV1 goes to the non-inverting input of U1, so the pot acts as an input attenuator.
- U1 is a valid single-supply audio power amp.
- Leaving pins 1 and 8 open sets the default gain to 20 V/V (26 dB) per the datasheet.
- C6, 10 uF from BYPASS to ground, improves PSRR and reduces supply noise.
- C7, 470 uF, AC-couples the output to the speaker terminal U2, which is correct for a single-supply LM386 output stage.
- J2 is wired center-positive: center pin to VIN, sleeve to GND, which matches the intended polarity from its datasheet lookup.
- Input decoupling is present:
- This matches the general decoupling pattern recommended for real circuits and simulation setups: local 100 nF plus bulk capacitance
This is the biggest issue.
The datasheet result for U1 shows:
- recommended load: 4 Ohm to 32 Ohm
- supply: 5 V to 12 V in the example design window
- but output power is nowhere near 3 W
The retrieved datasheet data says U1 is characterized at roughly 700 mW to 1 W under a 16 V / 32 Ohm condition, and the lower-voltage examples are below that. So for 4 Ohm or 8 Ohm at 5 V to 12 V, you should expect “small speaker amplifier” behavior, not a clean 3 W stage.
So:
- If your real goal is “audible hobby amp”: likely yes.
- If your real goal is “up to 3 W into 4 Ohm/8 Ohm”: no, this implementation does not justify that claim.
Your current netlist shows:
That is electrically usable as a volume control only if that orientation is intentional, but earlier the design notes indicated the pot’s grounded end should be on the opposite side. More importantly, the current implementation means the summed signal is on one end and ground on the other, which is correct in principle, but the naming/orientation has changed from the initial wiring log. I’d want to explicitly verify:
If that is indeed how it is now, it is okay. If not, the control law could be backwards or the input could be referenced incorrectly.
3. The board is not fully routed
The review shows 12 airwire errors, so the PCB is still electrically incomplete at the layout level. The review skill explicitly says DRC/ERC should be used to verify actual project state rather than assumptions
That means:
- schematic may be mostly fine
- PCB is not yet fabrication-ready
ERC reports floating:
These are not necessarily fatal:
So I treat those as acceptable intentional floats, not failures.
Additional engineering concerns
Output capacitor size vs 4 Ohm load
C7 is 470 uF. That works, but for 4 Ohm speakers the low-frequency rolloff is not great.
Approximate cutoff:
- 4 Ohm with 470 uF -> about 85 Hz
- 8 Ohm with 470 uF -> about 42 Hz
So:
- for voice / small speaker use: okay
- for fuller bass into 4 Ohm: you may want 1000 uF or larger
Many U1 application circuits include a small series RC from output to ground for stability. This design currently has no obvious Zobel network. It may still work, but speaker cable/load behavior can be less controlled.
No input bias reference issue? Mostly okay
R4 gives the input a defined return to ground, which is good. Since the source is AC-coupled and the LM386 input bias current is tiny, this is reasonable.
My practical conclusion
Will it work?
- Yes, probably as a basic mono line-level-to-speaker amplifier.
- No, not as a justified 3 W design.
- No, not yet as a finished PCB ready to build, because the layout still has unrouted airwires.
- Schematic concept: medium-high
- As-built PCB success right now: medium-low
- Meeting your original power target: low
What I would change before calling it verified
| Priority | Change | Reason |
|---|---|---|
| 1 | Replace U1 if you truly want 3 W | Current IC choice does not support your stated output target. |
| 2 | Explicitly confirm RV1 end-to-end wiring | Avoid inverted or malformed volume control behavior. |
| 3 | Finish routing and clear all airwires | Required before fabrication. |
| 4 | Consider increasing C7 | Better bass response, especially with 4 Ohm load. |
| 5 | Consider an output Zobel network | Improves LM386 stability with real speaker loads. |
If you want, I can do the next step and give you a strict pass/fail design review with:
- what is correct
- what is risky
- what is wrong
- and the minimum edits needed to make it robust.
Strict pass/fail review
Check remaining airwires
Review decoupling and stability
Find a 3W replacement
Check output capacitor
14 days
Plan completed.
U1
C1 P2 - R1 P1
R3 P2 - LED1 A
U1 VS - J2 Center pin
U1 VS - J2 Center pin
J1 L - C1 P1
C2 P2 - R2 P1
C7 P2 - U2 1
VR1 WIPER - U1 +_INPUT
R1 P2 - R2 P2
U1 VS - J2 Center pin
VR1 WIPER - U1 +_INPUT
U1 VOUT - C7 P1
U1 VS - J2 Center pin
U1 VS - J2 Center pin
R1 P2 - R2 P2
R1 P2 - R2 P2
J1 R - C2 P1
VR1 WIPER - U1 +_INPUT
U1 BYPASS - C6 P1
U1 BYPASS - C6 P1
U1 VS - J2 Center pin
C5
Capacitance
100nF
RV1
Resistance
10kΩ
C3
Capacitance
220uF
C4
Capacitance
100nF
C6
Capacitance
10uF
GND
GND
GND
GND
GND
GND
GND
GND
GND
GND
GND
J2
U2
J1
R2
Resistance
1kΩ
R1
Resistance
1kΩ
R4
Resistance
10kΩ
R3
Resistance
2.2kΩ
Reviews
- Wirelessly connects nets on schematic. Used to organize schematics and separate functional blocks. To wirelessly connect net portals, give them same designator. #portaljharwinbarrozo43.0M
- Wirelessly connects power nets on schematic. Identical to the net portal, but with a power symbol. Used to organize schematics and separate functional blocks. To wirelessly connect power net portals, give them the same designator. #portal #powerjharwinbarrozo11.4M
- A generic fixed resistor ideal for rapid circuit topology development. Its footprint automatically adapts based on the selected package case code—supporting 0402, 0603, 0805, 1203, and many other standard SMD packages, as well as axial horizontal and vertical configurations. Save precious design time by seamlessly add more information to this part (value, footprint, etc.) as it becomes available. Standard resistor values: 1.0 ohm, 10 ohm, 100 ohm, 1.0k ohm, 10k ohm, 100k ohm, 1.0M ohm 1.1 ohm, 11 ohm, 110 ohm, 1.1k ohm, 11k ohm, 110k ohm, 1.1M ohm 1.2 ohm, 12 ohm, 120 ohm, 1.2k ohm, 12k ohm, 120k ohm, 1.2M ohm 1.3 ohm, 13 ohm, 130 ohm, 1.3k ohm, 13k ohm, 130k ohm, 1.3M ohm 1.5 ohm, 15 ohm, 150 ohm, 1.5k ohm, 15k ohm, 150k ohm, 1.5M ohm 1.6 ohm, 16 ohm, 160 ohm, 1.6k ohm, 16k ohm, 160k ohm, 1.6M ohm 1.8 ohm, 18 ohm, 180 ohm, 1.8K ohm, 18k ohm, 180k ohm, 1.8M ohm 2.0 ohm, 20 ohm, 200 ohm, 2.0k ohm, 20k ohm, 200k ohm, 2.0M ohm 2.2 ohm, 22 ohm, 220 ohm, 2.2k ohm, 22k ohm, 220k ohm, 2.2M ohm 2.4 ohm, 24 ohm, 240 ohm, 2.4k ohm, 24k ohm, 240k ohm, 2.4M ohm 2.7 ohm, 27 ohm, 270 ohm, 2.7k ohm, 27k ohm, 270k ohm, 2.7M ohm 3.0 ohm, 30 ohm, 300 ohm, 3.0K ohm, 30K ohm, 300K ohm, 3.0M ohm 3.3 ohm, 33 ohm, 330 ohm, 3.3k ohm, 33k ohm, 330k ohm, 3.3M ohm 3.6 ohm, 36 ohm, 360 ohm, 3.6k ohm, 36k ohm, 360k ohm, 3.6M ohm 3.9 ohm, 39 ohm, 390 ohm, 3.9k ohm, 39k ohm, 390k ohm, 3.9M ohm 4.3 ohm, 43 ohm, 430 ohm, 4.3k ohm, 43K ohm, 430K ohm, 4.3M ohm 4.7 ohm, 47 ohm, 470 ohm, 4.7k ohm, 47k ohm, 470k ohm, 4.7M ohm 5.1 ohm, 51 ohm, 510 ohm, 5.1k ohm, 51k ohm, 510k ohm, 5.1M ohm 5.6 ohm, 56 ohm, 560 ohm, 5.6k ohm, 56k ohm, 560k ohm, 5.6M ohm 6.2 ohm, 62 ohm, 620 ohm, 6.2k ohm, 62K ohm, 620K ohm, 6.2M ohm 6.8 ohm, 68 ohm, 680 ohm, 6.8k ohm, 68k ohm, 680k ohm, 6.8M ohm 7.5 ohm, 75 ohm, 750 ohm, 7.5k ohm, 75k ohm, 750k ohm, 7.5M ohm 8.2 ohm, 82 ohm, 820 ohm, 8.2k ohm, 82k ohm, 820k ohm, 8.2M ohm 9.1 ohm, 91 ohm, 910 ohm, 9.1k ohm, 91k ohm, 910k ohm, 9.1M ohm #generics #CommonPartsLibraryjharwinbarrozo1.5M
- A generic fixed capacitor ideal for rapid circuit topology development. You can choose between polarized and non-polarized types, its symbol and the footprint will automatically adapt based on your selection. Supported options include standard SMD sizes for ceramic capacitors (e.g., 0402, 0603, 0805), SMD sizes for aluminum electrolytic capacitors, and through-hole footprints for polarized capacitors. Save precious design time by seamlessly add more information to this part (value, footprint, etc.) as it becomes available. Standard capacitor values: 1.0pF, 10pF, 100pF, 1000pF, 0.01uF, 0.1uF, 1.0uF, 10uF, 100uF, 1000uF, 10000uF 1.1pF, 11pF, 110pF, 1100pF 1.2pF, 12pF, 120pF, 1200pF 1.3pF, 13pF, 130pF, 1300pF 1.5pF, 15pF, 150pF, 1500pF, 0.015uF, 0.15uF, 1.5uF, 15uF, 150uF, 1500uF 1.6pF, 16pF, 160pF, 1600pF 1.8pF, 18pF, 180pF, 1800pF 2.0pF, 20pF, 200pF, 2000pF 2.2pF, 22pF, 220pF, 2200pF, 0.022uF, 0.22uF, 2.2uF, 22uF, 220uF, 2200uF 2.4pF, 24pF, 240pF, 2400pF 2.7pF, 27pF, 270pF, 2700pF 3.0pF, 30pF, 300pF, 3000pF 3.3pF, 33pF, 330pF, 3300pF, 0.033uF, 0.33uF, 3.3uF, 33uF, 330uF, 3300uF 3.6pF, 36pF, 360pF, 3600pF 3.9pF, 39pF, 390pF, 3900pF 4.3pF, 43pF, 430pF, 4300pF 4.7pF, 47pF, 470pF, 4700pF, 0.047uF, 0.47uF, 4.7uF, 47uF, 470uF, 4700uF 5.1pF, 51pF, 510pF, 5100pF 5.6pF, 56pF, 560pF, 5600pF 6.2pF, 62pF, 620pF, 6200pF 6.8pF, 68pF, 680pF, 6800pF, 0.068uF, 0.68uF, 6.8uF, 68uF, 680uF, 6800uF 7.5pF, 75pF, 750pF, 7500pF 8.2pF, 82pF, 820pF, 8200pF 9.1pF, 91pF, 910pF, 9100pF #generics #CommonPartsLibraryjharwinbarrozo1.5M
- A generic fixed inductor suitable for rapid circuit topology development. The footprint automatically adapts based on the selected package, supporting standard SMD sizes (e.g., 0402, 0603, 0805) as well as well-known inductor packages such as SDR1806, PA4320, SRN6028, and SRR1260. Standard inductor values: 1.0 nH, 10 nH, 100 nH, 1.0 µH, 10 µH, 100 µH, 1.0 mH 1.2 nH, 12 nH, 120 nH, 1.2 µH, 12 µH, 120 µH, 1.2 mH 1.5 nH, 15 nH, 150 nH, 1.5 µH, 15 µH, 150 µH, 1.5 mH 1.8 nH, 18 nH, 180 nH, 1.8 µH, 18 µH, 180 µH, 1.8 mH 2.2 nH, 22 nH, 220 nH, 2.2 µH, 22 µH, 220 µH, 2.2 mH 2.7 nH, 27 nH, 270 nH, 2.7 µH, 27 µH, 270 µH, 2.7 mH 3.3 nH, 33 nH, 330 nH, 3.3 µH, 33 µH, 330 µH, 3.3 mH 3.9 nH, 39 nH, 390 nH, 3.9 µH, 39 µH, 390 µH, 3.9 mH 4.7 nH, 47 nH, 470 nH, 4.7 µH, 47 µH, 470 µH, 4.7 mH 5.6 nH, 56 nH, 560 nH, 5.6 µH, 56 µH, 560 µH, 5.6 mH 6.8 nH, 68 nH, 680 nH, 6.8 µH, 68 µH, 680 µH, 6.8 mH 8.2 nH, 82 nH, 820 nH, 8.2 µH, 82 µH, 820 µH, 8.2 mH #generics #CommonPartsLibraryjharwinbarrozo15.7k
- An electrical connector acting as reusable interface to a conductor and creating a point where external circuits can be connected.Terminal
- 47 kOhms ±5% 0.125W, 1/8W Chip Resistor 0805 (2012 Metric) Automotive AEC-Q200 Thick Film #forLedBlinkjharwinbarrozo1.2M
- 10uF Capacitor Aluminum Polymer 20% 16V SMD 5x5.3mm #forLedBlink #commonpartslibrary #capacitor #aluminumpolymer #radialcanjharwinbarrozo1.2M
- Yellow 595nm LED Indication - Discrete 1.7V 1206 (3216 Metric) #forLedBlinkjharwinbarrozo1.1M
Mono Audio Amplifier
Compact 5 V-12 V mono audio amplifier with stereo 3.5 mm summed input, 10 kOhm log volume control, LM386 power stage, speaker output, power LED, and 2-layer 50 mm x 50 mm layout target.
Properties
Properties describe core aspects of the project.
Pricing & Availability
Distributor | Qty 1 |
|---|
Controls
Welcome 👋
Flux helps you build PCBs faster with an AI teammate!
Create your account to collaborate, stay updated, fork your own version, and get instant answers from our AI agent.