Chat

Welcome to Flux

Treat Flux like your intern. Tell it what you'd like to build and it'll get to work. You can also ask it questions, brainstorm ideas, and teach it your preferences. Learn More

Explain project
Write a project description
Find schematic issues
Create a test plan

Ready.

Sign up to send
how to use q1 as zero crossing detection for sine wave frequency 50hz magnitude ...
maghji

maghji

@copilot how to use q1 as zero crossing detection for sine wave frequency 50hz magnitude 220v
2y

copilot

The H11AA1M is an optocoupler suitable for directly interfacing with AC mains for zero-crossing detection. Here is a general guideline on how you can use it for detecting zero crossing on a 220V, 50Hz sine wave:
  1. AC Mains input series resistor: Connect input pins 1 and 2 of the H11AA1M to the AC mains. It is essential to put a suitable series resistor for current limiting. For a 220V, 50Hz input, you should choose a resistor high enough to limit the current to a safe level (below the device's 60mA peak). Let's assume a 2mA current through the device. If the peak voltage is $V_{peak} = \sqrt{2} \times 220V \approx 311 V$, the resistor value can be calculated:
[ R = \frac{V_{peak} - V_{LED}}{I} ]
where $V_{LED}=1.2V$ is the voltage across the internal LED and I is the desired current (2mA in this case). This gives $R \approx 155 k\Omega$. It is typical to use a 1-watt resistor for this role. It's safer to use a higher value if unsure, as a lower value would cause a higher current, which could eventually damage the optoisolator.
  1. Connect to Microcontroller: The collector (C, pin 5) and emitter (E, pin 4) can be connected to an input pin of your microcontroller (U1, STM32, aka "Blue Pill"). Connect the collector to a digital I/O pin on the Blue Pill (pin PA0 for example), and the emitter to the ground of U1. You might want to add a pull-up resistor between the collector and the microcontroller's I/O power (3.3V typically). This is to ensure the logic level at the I/O pin is high when the transistor inside the H11AA1M is not conducting (i.e., the AC signal is at its zero crossing).
  2. Powering the H11AA1M: The H11AA1M does not require any external power supply as it is a passive component.
So in summary:
  • Connect a current limiting resistor to IN1 or IN2 of Q1, and connect the other end to one lead of a 50Hz 220V AC.
  • Connect the other lead of the 50Hz 220V AC to the other IN pin (not connected to resistor) of Q1.
  • Connect the collector (C) on Q1 to pin PA0 on U1 via a pull-up resistor to 3V3 on U1 (assuming PA0 is a free digital input pin on U1).
  • Connect the emitter (E) pin of Q1 to the GND pin on U1.
A periodic digital signal that goes high around the zero-cross points of your AC input should be present at the chosen input pin of the U1 microcontroller. Inside your software running on the STM32, you can set up an interrupt routine that is triggered at every rising or falling edge of this signal, giving you precise control and knowledge of every zero cross in the AC wave.
This method isolates the microcontroller from the high voltage AC, providing safety and noise immunity.
Please note: Working with mains voltage (220V AC) can be dangerous. Always follow proper safety precautions when working with high voltage and use a transformer or similar isolating power supply when testing if possible.
2y
Q1
U1
  • Ground
    Ground
    A common return path for electric current. Commonly known as ground.
    jharwinbarrozo
    20.5M
  • Net Portal
    Net Portal
    Wirelessly connects nets on schematic. Used to organize schematics and separate functional blocks. To wirelessly connect net portals, give them same designator. #portal
    jharwinbarrozo
    43.0M
  • Power Net Portal
    Power Net Portal
    Wirelessly connects power nets on schematic. Identical to the net portal, but with a power symbol. Used to organize schematics and separate functional blocks. To wirelessly connect power net portals, give them the same designator. #portal #power
    jharwinbarrozo
    11.4M
  • Generic Resistor
    Generic Resistor
    A generic fixed resistor for rapid developing circuit topology. Save precious design time by seamlessly add more information to this part (value, footprint, etc.) as it becomes available. Standard resistor values: 1.0Ω 10Ω 100Ω 1.0kΩ 10kΩ 100kΩ 1.0MΩ 1.1Ω 11Ω 110Ω 1.1kΩ 11kΩ 110kΩ 1.1MΩ 1.2Ω 12Ω 120Ω 1.2kΩ 12kΩ 120kΩ 1.2MΩ 1.3Ω 13Ω 130Ω 1.3kΩ 13kΩ 130kΩ 1.3MΩ 1.5Ω 15Ω 150Ω 1.5kΩ 15kΩ 150kΩ 1.5MΩ 1.6Ω 16Ω 160Ω 1.6kΩ 16kΩ 160kΩ 1.6MΩ 1.8Ω 18Ω 180Ω 1.8KΩ 18kΩ 180kΩ 1.8MΩ 2.0Ω 20Ω 200Ω 2.0kΩ 20kΩ 200kΩ 2.0MΩ 2.2Ω 22Ω 220Ω 2.2kΩ 22kΩ 220kΩ 2.2MΩ 2.4Ω 24Ω 240Ω 2.4kΩ 24kΩ 240kΩ 2.4MΩ 2.7Ω 27Ω 270Ω 2.7kΩ 27kΩ 270kΩ 2.7MΩ 3.0Ω 30Ω 300Ω 3.0KΩ 30KΩ 300KΩ 3.0MΩ 3.3Ω 33Ω 330Ω 3.3kΩ 33kΩ 330kΩ 3.3MΩ 3.6Ω 36Ω 360Ω 3.6kΩ 36kΩ 360kΩ 3.6MΩ 3.9Ω 39Ω 390Ω 3.9kΩ 39kΩ 390kΩ 3.9MΩ 4.3Ω 43Ω 430Ω 4.3kΩ 43KΩ 430KΩ 4.3MΩ 4.7Ω 47Ω 470Ω 4.7kΩ 47kΩ 470kΩ 4.7MΩ 5.1Ω 51Ω 510Ω 5.1kΩ 51kΩ 510kΩ 5.1MΩ 5.6Ω 56Ω 560Ω 5.6kΩ 56kΩ 560kΩ 5.6MΩ 6.2Ω 62Ω 620Ω 6.2kΩ 62KΩ 620KΩ 6.2MΩ 6.8Ω 68Ω 680Ω 6.8kΩ 68kΩ 680kΩ 6.8MΩ 7.5Ω 75Ω 750Ω 7.5kΩ 75kΩ 750kΩ 7.5MΩ 8.2Ω 82Ω 820Ω 8.2kΩ 82kΩ 820kΩ 8.2MΩ 9.1Ω 91Ω 910Ω 9.1kΩ 91kΩ 910kΩ 9.1MΩ #generics #CommonPartsLibrary
    jharwinbarrozo
    1.5M
  • Generic Capacitor
    Generic Capacitor
    A generic fixed capacitor ideal for rapid circuit topology development. You can choose between polarized and non-polarized types, its symbol and the footprint will automatically adapt based on your selection. Supported options include standard SMD sizes for ceramic capacitors (e.g., 0402, 0603, 0805), SMD sizes for aluminum electrolytic capacitors, and through-hole footprints for polarized capacitors. Save precious design time by seamlessly add more information to this part (value, footprint, etc.) as it becomes available. Standard capacitor values: 1.0pF 10pF 100pF 1000pF 0.01uF 0.1uF 1.0uF 10uF 100uF 1000uF 10,000uF 1.1pF 11pF 110pF 1100pF 1.2pF 12pF 120pF 1200pF 1.3pF 13pF 130pF 1300pF 1.5pF 15pF 150pF 1500pF 0.015uF 0.15uF 1.5uF 15uF 150uF 1500uF 1.6pF 16pF 160pF 1600pF 1.8pF 18pF 180pF 1800pF 2.0pF 20pF 200pF 2000pF 2.2pF 22pF 20pF 2200pF 0.022uF 0.22uF 2.2uF 22uF 220uF 2200uF 2.4pF 24pF 240pF 2400pF 2.7pF 27pF 270pF 2700pF 3.0pF 30pF 300pF 3000pF 3.3pF 33pF 330pF 3300pF 0.033uF 0.33uF 3.3uF 33uF 330uF 3300uF 3.6pF 36pF 360pF 3600pF 3.9pF 39pF 390pF 3900pF 4.3pF 43pF 430pF 4300pF 4.7pF 47pF 470pF 4700pF 0.047uF 0.47uF 4.7uF 47uF 470uF 4700uF 5.1pF 51pF 510pF 5100pF 5.6pF 56pF 560pF 5600pF 6.2pF 62pF 620pF 6200pF 6.8pF 68pF 680pF 6800pF 0.068uF 0.68uF 6.8uF 68uF 680uF 6800uF 7.5pF 75pF 750pF 7500pF 8.2pF 82pF 820pF 8200pF 9.1pF 91pF 910pF 9100pF #generics #CommonPartsLibrary
    jharwinbarrozo
    1.5M
  • Generic Inductor
    Generic Inductor
    A generic fixed inductor for rapid developing circuit topology. *You can now change the footprint and 3D model at the top level anytime you want. This is the power of #generics
    jharwinbarrozo
    15.1k
  • Terminal
    Terminal
    An electrical connector acting as reusable interface to a conductor and creating a point where external circuits can be connected.
    natarius
  • RMCF0805JT47K0
    RMCF0805JT47K0
    47 kOhms ±5% 0.125W, 1/8W Chip Resistor 0805 (2012 Metric) Automotive AEC-Q200 Thick Film #forLedBlink
    jharwinbarrozo
    1.2M
  • 875105359001
    875105359001
    10uF Capacitor Aluminum Polymer 20% 16V SMD 5x5.3mm #forLedBlink #commonpartslibrary #capacitor #aluminumpolymer #radialcan
    jharwinbarrozo
    1.2M
  • CTL1206FYW1T
    CTL1206FYW1T
    Yellow 595nm LED Indication - Discrete 1.7V 1206 (3216 Metric) #forLedBlink
    jharwinbarrozo
    1.1M

Inspect

Hostile Lime Dejarik

Hostile Lime Dejarik
Description

Created
Last updated by maghji
1 Contributor(s)
maghji

Controls

Properties

Availability & Pricing

DistributorQty 1
Digi-Key$0.25–$0.92
LCSC$0.46
Mouser$0.78–$0.92

Assets