Adding CUS-14TB 3D Model


Added the matching

3D Model

and verified its scale, orientation, seating, and alignment with all ten pads; the footprint is unchanged. Details are in Package Model Verification.
The model is saved in this part project but not yet published as a new library version.
then set the direction rule and edge placement offset if applicable
I’ll check the actuator’s facing direction and whether this switch needs a board-edge offset, then set the applicable rules.
Thought for 3 mins 34 sec
Thought for 12 sec
Referenced guidance.
Thought for 38 sec
Thought for 7 sec
Awaiting 1 task
"CUS-14TB 3D Model" completed.
Set Edge Direction to 180° (local −Y), toward the slide actuator. I left Edge Placement Offset unset because aligning the board edge with the body face would leave mounting pads partially off-board; the rationale is recorded in Package Model Verification.

Package Model Verification
Result and scope
Completed: sourced and attached the exact CUS-14TB STEP package, aligned it to the existing footprint, and inspected persisted 3D views. Electrical pins, footprint pads, holes, silkscreen, schematic and BOM were preserved. No publication was performed; the asset and model node persist in the current editable project. Authored build123d fallback was unattempted because a usable catalog STEP was found.

3D Model

Design view of Package Model Verification
Provenance and license
The Nidec product page https://www.nidec-components.com/eu/product/detail/00000195/ offers CUS-14TB CAD through CADENAS/web2cad, with a login-required download link. An existing exact CUS-14TB catalog export was obtained unchanged from the public repository at https://raw.githubusercontent.com/bkw777/WP-2_IC-Card/4d4dbf565371/PCB/000_LOCAL.pretty/3d/CUS-14TB.stp (repository commit prefix 4d4dbf565371).
STEP header: FILE_NAME CUS-14TB; timestamp 2023-01-17T18:03:00+01:00; organization CADENAS; originating system PARTsolutions; author field License CC BY-ND 4.0. Attribution: CADENAS/PARTsolutions, CUS-14TB; hosted copy by bkw777/WP-2_IC-Card. License: https://creativecommons.org/licenses/by-nd/4.0/. Geometry and source bytes were not edited; placement is a model-node rigid transform. This is a catalog-origin model obtained from a third-party repository, not a fresh authenticated vendor download; authenticity beyond the embedded header and geometry comparison is not independently certified.
SHA-256: 031d0759246f8d065e66822d7214872bfc1f2ced3c7c2d8dd7ad813e02d6c724.
Geometry evidence
Values below are measurements of the downloaded STEP using build123d/OpenCascade, not successful automated datasheet extractions. The Nidec mechanical drawing was also visually checked; automated datasheet dimension extraction was unresolved and must not be represented as a verified machine citation.
  • Body/shell nominal envelope: 11.3 × 2.6 × 1.4 mm (excluding outward solder feet, actuator and locating bosses).
  • Entire source STEP bounds: X −6.15…+6.15 mm; Y −1.9000001…0 mm; Z −2.2…+2.8 mm.
  • Two solids: slider volume 0.9915327412 mm³ and body assembly volume 39.6924419537 mm³. The catalog model groups metals/plastic geometry within its body assembly; no artificial pin-1 dimple was added.
  • Six signal terminals: X centers −3.75, −2.25, −0.75, +0.75, +2.25, +3.75 mm; pitch 1.5 mm. Flat footprint-facing lead geometry 0.4 × 0.9 mm, thickness 0.2 mm.
  • Four end solder feet: 0.45 × 0.4 mm flat bounding regions, thickness 0.25 mm.
  • Slider width 1.3 mm, thickness 0.4 mm, outward extension 1.5 mm; displayed at X=+0.75 mm, matching the existing drawn actuator position.
  • Locating bosses: centers X=±2.5 mm, diameter 0.8 mm, bottom depth 0.5 mm below seating plane.
Visual source drawing (Nidec CUS catalog, outline dimensions, CUS-14B; T denotes tape packaging):

cus14-detail

cus-dimensions

Persisted placement
Owning footprint UID: 326022f7-7790-459d-9d02-1d074ca5c887.defaultFootprint. Model node UID: 396a780e-2a68-4896-9e76-c382607d3f3d, label Slide Switch. Asset rule: CUS-14TB-CADENAS.stp.
  • Position: (0, −0.35, +1.4) mm.
  • Rotation XYZ: (90, 0, 0) degrees.
  • Scale: unity on all axes, no additional mm-to-m conversion.
  • zIsUp: true; the explicit X rotation handles the original CAD frame.
  • physicalMaterials: true; showEdges: false (default).
  • Mapping from STEP frame: Xscene=Xstep; Yscene=−Zstep−0.35; Zscene=Ystep+1.4 in mm.
  • Transformed complete bounds: X −6.15…6.15, Y −3.15…1.85, Z −0.5000001…1.4 mm.
  • All solder feet seat at local Z=0; only the intended locating bosses extend below it. Body top is +1.4 mm.
Alignment to computed pad positions
Used the scene-tree computed positions, not the Y-inverted embedded KiCad payload. Footprint rotation is zero and side is Top. Pad 1 is in the (−X,+Y) quadrant at (−3.75,+1.4) mm.

Table


PadsComputed centers (mm)Model match
1–6X −3.75 to +3.75 in 1.5 steps, Y +1.4Lead center error zero; lead 0.4×0.9 lies inside 0.7×1.5 pad, with 0.15 mm X / 0.30 mm Y margin on each side
7(+5.9,+0.7)Flat foot bounding center (+5.925,+0.7); +0.025 mm X offset; entirely inside pad
8(+5.9,−1.4)Flat foot bounding center (+5.925,−1.4); +0.025 mm X offset; entirely inside pad
9(−5.9,−1.4)Flat foot bounding center (−5.925,−1.4); −0.025 mm X offset; entirely inside pad
10(−5.9,+0.7)Flat foot bounding center (−5.925,+0.7); −0.025 mm X offset; entirely inside pad
Locating holes(±2.5,−0.35), diameter 0.9Boss centers match; nominal radial clearance 0.05 mm
The STEP terminal number is inferred from the unchanged left-to-right six-terminal geometry and the drawing's terminal 1 callout, not a numbered solid label.
Read-only verification
Native 3D inspection returned one model under the owning footprint and rendered iso, top and front views: the package is right-side-up, lead centers overlay pads, the actuator points toward −Y, shell tabs overlay their four pads, and bosses point below seating. Scene readback confirms the asset path, unity scale, transforms and materials above.
Project diff from baseline c68166c1 reports no schematic changes, no BOM changes, and only the new model in the PCB layout. The model mutation's DRC checks returned NOT CHECKED/no validator result; this is not a clean DRC claim. A full electrical/manufacturing audit was outside scope.
Limitations
This completes the assigned package-model batch, not validation of the entire part library entry. The model is nominal catalog geometry, not a manufacturing tolerance analysis. Direct vendor CAD download requires login; public catalog export provenance is as stated above. No electrical mapping or footprint correction was attempted, and no publication was needed or requested.
Edge direction follow-up
Completed: set edgeDirection = 180deg on footprint 326022f7-7790-459d-9d02-1d074ca5c887.defaultFootprint. Live rule configuration maps 180 degrees to local −Y at footprint rotation zero, which is the outward direction of the side actuator. This is placement-orientation guidance, not a claim that the switch must mount at a board edge.
Offset assessment completed; setting edgePlacementOffset was intentionally unattempted and it remains unset. The measured actuator-side body face in the unchanged STEP is Zstep=+1.3 mm, hence Yscene=−1.3−0.35=−1.65 mm. A body-face edge datum would therefore be an offset of 1.65 mm along −Y. However, existing pads 8 and 9 are centered at Y=−1.4 mm and their rotated copper extent in Y is 0.8 mm: the outward copper edge is −1.4−0.8/2=−1.8 mm. A straight board edge at the body face would leave 0.15 mm of each pad outside the board, failing the requested all-pads-on-board condition. Thus 1.65 mm was not applied.
The actuator tip at Y=−3.15 mm is not a board-edge datum and was not used. No arbitrary replacement offset was invented from pad extents: an actual board requires a selected copper-to-edge clearance, routing tolerance, mechanical access plan and possibly a shaped edge. Those are board-specific decisions, not supported mandatory package dimensions. With the offset unset, the tool's documented fallback is the footprint bounding-box edge; this fallback is not asserted to be an approved mechanical datum.
Read-only scene-tree inspection confirmed the persisted edgeDirection: 180deg, no edgePlacementOffset rule, and the unchanged footprint asset and existing rulesets. Only the edgeDirection rule and this report were edited in this follow-up; no pads, pins, holes, model transforms, geometry or publication state were changed. Post-mutation DRC returned NOT CHECKED/no validator result, so no clean DRC claim is made.
  • Result and scope

  • Provenance and license

  • Geometry evidence

  • Persisted placement

  • Alignment to computed pad positions

  • Read-only verification

  • Limitations

  • Edge direction follow-up