Temperature and Humidity Sensor Design

flux

Here’s how the PCB layout phase will proceed and what I’ll focus on, tailored to your design:
  • Board outline and placement anchors
    • Set a compact provisional board (about 50 x 35 mm).
    • Reserve a straight board edge for the USB-C receptacle.
    • Place the ESP32-S3 module U1 so the antenna area faces the board edge with a clear RF keepout.
    • Place the SHTC3 sensor U2 near an opening/edge for airflow, away from heat sources.
  • RF keepout and rules
    • Define a 2.4 GHz antenna keepout area around U1 with no copper pours, traces, or components beneath/near the antenna.
    • Keep ground reference continuous under digital areas; avoid stitching vias in the antenna keepout.
    • Set conservative default trace width/via sizes suitable for 2-layer or 4-layer stackups.
  • Functional grouping
    • Cluster SW1–SW4 for user ergonomics; place SW5 (BTN_CLR) and SW6 (BTN_PWR) apart to reduce accidental presses.
    • Place the TVS diodes D1–D6 close to their respective buttons to minimize loop area.
    • Keep pull-up resistors R1–R6 near the MCU side to ensure defined logic levels.
  • Power integrity
    • Route USB VBUS short to input protection and regulator (to be added) with wide traces; add local bulk and high-frequency decoupling.
    • Place decoupling capacitors as close as possible to U1 and U2 supply pins with short returns to GND.
  • Manufacturability and test
    • Maintain component-to-edge clearances for USB-C and buttons.
    • Add test pads for 3V3, GND, key button nets, and UART/boot signals.
If you want, I can proceed to set the provisional board size and start placing these anchors, then we can iterate on exact dimensions and connector orientation.
Ask about antenna keepout size
Clarify stackup choice
Button placement strategy
Ask about USB-C area layout
Test pad recommendations

Flux stopped

R1 P1 - SW1 P1
D6 2 - GND GND
R1 P1 - SW1 P1
R1 P1 - SW1 P1
R1 P1 - SW1 P1
R1 P1 - SW1 P1
R1 P1 - SW1 P1
R1 P1 - SW1 P1
R1 P1 - SW1 P1
R1 P1 - SW1 P1
R1 P1 - SW1 P1
R1 P1 - SW1 P1
R1 P1 - SW1 P1
U1 3V3 - R1 P2
R1 P1 - SW1 P1
R1 P1 - SW1 P1
D6 2 - GND GND
R1 P1 - SW1 P1
R1 P1 - SW1 P1
R1 P1 - SW1 P1
R1 P1 - SW1 P1
R1 P1 - SW1 P1
R1 P1 - SW1 P1
R1 P1 - SW1 P1
D6 2 - GND GND
R1 P1 - SW1 P1
R1 P1 - SW1 P1
R1 P1 - SW1 P1
R1 P1 - SW1 P1
GND
D1
R3
Resistance
10kΩ
U2
D4
D2
R5
Resistance
10kΩ
D3
R4
Resistance
10kΩ
U1
R1
Resistance
10kΩ
D6
R6
Resistance
10kΩ
D5
R2
Resistance
10kΩ
  • Generic Inductor
    Generic Inductor
    A generic fixed inductor suitable for rapid circuit topology development. The footprint automatically adapts based on the selected package, supporting standard SMD sizes (e.g., 0402, 0603, 0805) as well as well-known inductor packages such as SDR1806, PA4320, SRN6028, and SRR1260. Standard inductor values: 1.0 nH, 10 nH, 100 nH, 1.0 µH, 10 µH, 100 µH, 1.0 mH 1.2 nH, 12 nH, 120 nH, 1.2 µH, 12 µH, 120 µH, 1.2 mH 1.5 nH, 15 nH, 150 nH, 1.5 µH, 15 µH, 150 µH, 1.5 mH 1.8 nH, 18 nH, 180 nH, 1.8 µH, 18 µH, 180 µH, 1.8 mH 2.2 nH, 22 nH, 220 nH, 2.2 µH, 22 µH, 220 µH, 2.2 mH 2.7 nH, 27 nH, 270 nH, 2.7 µH, 27 µH, 270 µH, 2.7 mH 3.3 nH, 33 nH, 330 nH, 3.3 µH, 33 µH, 330 µH, 3.3 mH 3.9 nH, 39 nH, 390 nH, 3.9 µH, 39 µH, 390 µH, 3.9 mH 4.7 nH, 47 nH, 470 nH, 4.7 µH, 47 µH, 470 µH, 4.7 mH 5.6 nH, 56 nH, 560 nH, 5.6 µH, 56 µH, 560 µH, 5.6 mH 6.8 nH, 68 nH, 680 nH, 6.8 µH, 68 µH, 680 µH, 6.8 mH 8.2 nH, 82 nH, 820 nH, 8.2 µH, 82 µH, 820 µH, 8.2 mH #generics #CommonPartsLibrary
    jharwinbarrozo
    16.5k
  • Generic Capacitor
    Generic Capacitor
    A generic fixed capacitor ideal for rapid circuit topology development. You can choose between polarized and non-polarized types, its symbol and the footprint will automatically adapt based on your selection. Supported options include standard SMD sizes for ceramic capacitors (e.g., 0402, 0603, 0805), SMD sizes for aluminum electrolytic capacitors, and through-hole footprints for polarized capacitors. Save precious design time by seamlessly add more information to this part (value, footprint, etc.) as it becomes available. Standard capacitor values: 1.0pF, 10pF, 100pF, 1000pF, 0.01uF, 0.1uF, 1.0uF, 10uF, 100uF, 1000uF, 10000uF 1.1pF, 11pF, 110pF, 1100pF 1.2pF, 12pF, 120pF, 1200pF 1.3pF, 13pF, 130pF, 1300pF 1.5pF, 15pF, 150pF, 1500pF, 0.015uF, 0.15uF, 1.5uF, 15uF, 150uF, 1500uF 1.6pF, 16pF, 160pF, 1600pF 1.8pF, 18pF, 180pF, 1800pF 2.0pF, 20pF, 200pF, 2000pF 2.2pF, 22pF, 220pF, 2200pF, 0.022uF, 0.22uF, 2.2uF, 22uF, 220uF, 2200uF 2.4pF, 24pF, 240pF, 2400pF 2.7pF, 27pF, 270pF, 2700pF 3.0pF, 30pF, 300pF, 3000pF 3.3pF, 33pF, 330pF, 3300pF, 0.033uF, 0.33uF, 3.3uF, 33uF, 330uF, 3300uF 3.6pF, 36pF, 360pF, 3600pF 3.9pF, 39pF, 390pF, 3900pF 4.3pF, 43pF, 430pF, 4300pF 4.7pF, 47pF, 470pF, 4700pF, 0.047uF, 0.47uF, 4.7uF, 47uF, 470uF, 4700uF 5.1pF, 51pF, 510pF, 5100pF 5.6pF, 56pF, 560pF, 5600pF 6.2pF, 62pF, 620pF, 6200pF 6.8pF, 68pF, 680pF, 6800pF, 0.068uF, 0.68uF, 6.8uF, 68uF, 680uF, 6800uF 7.5pF, 75pF, 750pF, 7500pF 8.2pF, 82pF, 820pF, 8200pF 9.1pF, 91pF, 910pF, 9100pF #generics #CommonPartsLibrary
    jharwinbarrozo
    1.5M
  • Generic Resistor
    Generic Resistor
    A generic fixed resistor ideal for rapid circuit topology development. Its footprint automatically adapts based on the selected package case code—supporting 0402, 0603, 0805, 1203, and many other standard SMD packages, as well as axial horizontal and vertical configurations. Save precious design time by seamlessly add more information to this part (value, footprint, etc.) as it becomes available. Standard resistor values: 1.0 ohm, 10 ohm, 100 ohm, 1.0k ohm, 10k ohm, 100k ohm, 1.0M ohm 1.1 ohm, 11 ohm, 110 ohm, 1.1k ohm, 11k ohm, 110k ohm, 1.1M ohm 1.2 ohm, 12 ohm, 120 ohm, 1.2k ohm, 12k ohm, 120k ohm, 1.2M ohm 1.3 ohm, 13 ohm, 130 ohm, 1.3k ohm, 13k ohm, 130k ohm, 1.3M ohm 1.5 ohm, 15 ohm, 150 ohm, 1.5k ohm, 15k ohm, 150k ohm, 1.5M ohm 1.6 ohm, 16 ohm, 160 ohm, 1.6k ohm, 16k ohm, 160k ohm, 1.6M ohm 1.8 ohm, 18 ohm, 180 ohm, 1.8K ohm, 18k ohm, 180k ohm, 1.8M ohm 2.0 ohm, 20 ohm, 200 ohm, 2.0k ohm, 20k ohm, 200k ohm, 2.0M ohm 2.2 ohm, 22 ohm, 220 ohm, 2.2k ohm, 22k ohm, 220k ohm, 2.2M ohm 2.4 ohm, 24 ohm, 240 ohm, 2.4k ohm, 24k ohm, 240k ohm, 2.4M ohm 2.7 ohm, 27 ohm, 270 ohm, 2.7k ohm, 27k ohm, 270k ohm, 2.7M ohm 3.0 ohm, 30 ohm, 300 ohm, 3.0K ohm, 30K ohm, 300K ohm, 3.0M ohm 3.3 ohm, 33 ohm, 330 ohm, 3.3k ohm, 33k ohm, 330k ohm, 3.3M ohm 3.6 ohm, 36 ohm, 360 ohm, 3.6k ohm, 36k ohm, 360k ohm, 3.6M ohm 3.9 ohm, 39 ohm, 390 ohm, 3.9k ohm, 39k ohm, 390k ohm, 3.9M ohm 4.3 ohm, 43 ohm, 430 ohm, 4.3k ohm, 43K ohm, 430K ohm, 4.3M ohm 4.7 ohm, 47 ohm, 470 ohm, 4.7k ohm, 47k ohm, 470k ohm, 4.7M ohm 5.1 ohm, 51 ohm, 510 ohm, 5.1k ohm, 51k ohm, 510k ohm, 5.1M ohm 5.6 ohm, 56 ohm, 560 ohm, 5.6k ohm, 56k ohm, 560k ohm, 5.6M ohm 6.2 ohm, 62 ohm, 620 ohm, 6.2k ohm, 62K ohm, 620K ohm, 6.2M ohm 6.8 ohm, 68 ohm, 680 ohm, 6.8k ohm, 68k ohm, 680k ohm, 6.8M ohm 7.5 ohm, 75 ohm, 750 ohm, 7.5k ohm, 75k ohm, 750k ohm, 7.5M ohm 8.2 ohm, 82 ohm, 820 ohm, 8.2k ohm, 82k ohm, 820k ohm, 8.2M ohm 9.1 ohm, 91 ohm, 910 ohm, 9.1k ohm, 91k ohm, 910k ohm, 9.1M ohm #generics #CommonPartsLibrary
    jharwinbarrozo
    1.5M
  • Ground
    Ground
    A common return path for electric current. Commonly known as ground.
    jharwinbarrozo
    20.5M
  • Terminal
    Terminal
    An electrical connector acting as reusable interface to a conductor and creating a point where external circuits can be connected.
    natarius
  • Net Portal
    Net Portal
    Wirelessly connects nets on schematic. Used to organize schematics and separate functional blocks. To wirelessly connect net portals, give them same designator. #portal
    jharwinbarrozo
    43.0M
  • RMCF0805JT47K0
    RMCF0805JT47K0
    General Purpose Thick Film Standard Power and High-Power Chip Resistor 47 kOhms ±5% 0.125W, 1/8W Chip Resistor 0805 (2012 Metric) Automotive AEC-Q200 Thick Film Features: - RMCF – standard power ratings - RMCP – high power ratings - Nickel barrier terminations standard - Power derating from 100% at 70ºC to zero at +155ºC - RoHS compliant, REACH compliant, and halogen free - AEC-Q200 compliant
    jharwinbarrozo
    1.2M
  • 875105359001
    875105359001
    10 µF 16 V Aluminum - Polymer Capacitors Radial, Can - SMD 30mOhm 2000 Hrs @ 105°C #commonpartslibrary #capacitor #aluminumpolymer #radialcan
    jharwinbarrozo
    1.2M
  • CTL1206FYW1T
    CTL1206FYW1T
    Yellow 595nm LED Indication - Discrete 1.7V 1206 (3216 Metric)
    jharwinbarrozo
    1.1M
  • 1070TR
    1070TR
    Battery Holder (Open) Coin, 20.0mm 1 Cell SMD (SMT) Tab bate or batt #forLedBlink
    jharwinbarrozo
    700.5k

Agreed Copper Scramble Suit

Agreed Copper Scramble Suit thumbnail
Active USB-C Wi-Fi & BLE Environmental Sensor Node with Cloud Connectivity and Integrated Six-Button User Interface

Properties

LED

USB-C

Buttons

3.3

V

Temperature/Humidity (SHTC3)

``` flowchart LR USB-C([USB-C Connector]) --> Protection([Input Protection]) Protection --> Regulator([3.3V Regulator]) Regulator --> MCU([MCU: Wi-Fi+BLE]) MCU --> SHTC3([Environmental Sensor - SHTC3]) MCU --> BTN1([BTN1 - Input Button 1]) MCU --> BTN2([BTN2 - Input Button 2]) MCU --> BTN3([BTN3 - Input Button 3]) MCU --> BTN4([BTN4 - Input Button 4]) MCU --> BTN_CLR([BTN_CLR - Clear Button]) MCU --> BTN_PWR([BTN_PWR - Power/On Button]) MCU --> LED([Status LED]) MCU --> HDR([Programming Header]) ```

Consumer Electronics

Bluetooth

WiFi

Pricing & Availability

Distributor

Qty 1

Arrow

$1.04

Digi-Key

$4.51–$4.85

LCSC

$5.86

Mouser

$6.71

TME

$0.00

Verical

$1.64–$1.89

Controls