Cpp
// Minimal BLE control for two DC motors via L293D on ESP32
// Motor A: U5 1A/2A -> D25/D26
// Motor B: U5 3A/4A -> D27/D14

#include 
#include 
#include 
#include 

#define M1_IN1 25  // U5:1A -> U1:D25 (Net 14)
#define M1_IN2 26  // U5:2A -> U1:D26 (Net 15)
#define M2_IN1 27  // U5:3A -> U1:D27 (Net 65)
#define M2_IN2 14  // U5:4A -> U1:D14 (Net 30)

// LEDC PWM setup
const int freq = 20000; // 20 kHz, above audible for most motors
const int res  = 8;     // 8-bit
const int ch1  = 0;
const int ch2  = 1;
const int ch3  = 2;
const int ch4  = 3;

// BLE UUIDs (random example UUIDs)
#define SVC_UUID  "6e400001-b5a3-f393-e0a9-e50e24dcca9e"
#define M1_UUID   "6e400002-b5a3-f393-e0a9-e50e24dcca9e" // write: -100..100
#define M2_UUID   "6e400003-b5a3-f393-e0a9-e50e24dcca9e" // write: -100..100

BLEServer* server;
BLECharacteristic* m1Char;
BLECharacteristic* m2Char;

int8_t clampCmd(int v) {
  if (v   100) v =  100;
  return (int8_t)v;
}

void driveMotor(int8_t cmd, int pwmFwdChan, int pwmRevChan, int revPin) {
  // cmd  reverse, cmd > 0 => forward
  int duty = map(abs(cmd), 0, 100, 0, 255);
  if (cmd > 0) {
    // forward: FWD PWM, REV low
    ledcWrite(pwmFwdChan, duty);
    ledcWrite(pwmRevChan, 0);
    // make sure the opposite GPIO is driven low
    // (LEDC holds pin low with duty 0, but set pinMode OUTPUT for safety)
  } else if (cmd getValue();
    if (value.empty()) return;

    // Expect 1-byte signed int (-100..100)
    int8_t cmd = (int8_t)value[0];
    cmd = clampCmd(cmd);

    if (c == m1Char) {
      // Motor A: M1_IN1 forward, M1_IN2 reverse
      driveMotor(cmd, ch1, ch2, M1_IN2);
    } else if (c == m2Char) {
      // Motor B: M2_IN1 forward, M2_IN2 reverse
      driveMotor(cmd, ch3, ch4, M2_IN2);
    }
  }
};

void setupPWM() {
  ledcSetup(ch1, freq, res);
  ledcSetup(ch2, freq, res);
  ledcSetup(ch3, freq, res);
  ledcSetup(ch4, freq, res);

  ledcAttachPin(M1_IN1, ch1);
  ledcAttachPin(M1_IN2, ch2);
  ledcAttachPin(M2_IN1, ch3);
  ledcAttachPin(M2_IN2, ch4);

  // Ensure all low at boot
  ledcWrite(ch1, 0);
  ledcWrite(ch2, 0);
  ledcWrite(ch3, 0);
  ledcWrite(ch4, 0);
}

void setupBLE() {
  BLEDevice::init("ESP32-RC-Car");
  server = BLEDevice::createServer();

  BLEService* svc = server->createService(SVC_UUID);

  m1Char = svc->createCharacteristic(M1_UUID, BLECharacteristic::PROPERTY_WRITE);
  m2Char = svc->createCharacteristic(M2_UUID, BLECharacteristic::PROPERTY_WRITE);

  m1Char->setCallbacks(new WriteCallbacks());
  m2Char->setCallbacks(new WriteCallbacks());

  svc->start();
  BLEAdvertising* adv = BLEDevice::getAdvertising();
  adv->addServiceUUID(SVC_UUID);
  BLEDevice::startAdvertising();
}

void setup() {
  // Pins to outputs (LEDC will manage level)
  pinMode(M1_IN1, OUTPUT);
  pinMode(M1_IN2, OUTPUT);
  pinMode(M2_IN1, OUTPUT);
  pinMode(M2_IN2, OUTPUT);

  setupPWM();
  setupBLE();
}

void loop() {
  // Nothing here; motor commands arrive via BLE writes
}

• Install nRF Connect (iOS/Android).
• Connect to “ESP32-RC-Car”.
• Write a single signed byte to the M1 and M2 characteristics:
  • 50 = forward half speed, -50 = reverse half, 0 = stop.
• If motors spin in the opposite direction, swap the two inputs for that motor in software (flip the sign) or swap the two wires at the motor.